Tender For Misc Civil Repairs Of Quarter No D1at New Shimla; (i) Concrete/ RCC (a) Rectification of structural / superficial / non-structural cracks. (b) Rectification of dampness / seepage in roof slab / junctions & sunken portion. (c) Rectification of cracks in beam, shade, column. (ii) Brick work/ Concrete Block Masonry (a) Rectification of cracks in panel wall / portion. (b) Cracks / settlement of dwarf walls. (c) Rectification of efflorescence/ leaching. (iii) Joinery (a) Replacement of warped joinery. (b) Cracks in panels, rails / styles etc. (iv) Builders Hardware (a) Repairs / Replacement of loosened / pre-mature failure of fittings. (b) Tightening / Replacement of sag in mosquito proofing. (v) Steel & Iron work (a) Rectification / Replacement of defective part of rolling shutter. (b) Redoing of defective portion in fabrication / welding including painting. (c) Steel windows, grills, gates etc. – defects to be rectified. (vi) Roof treatment (a) Rectification of leakage / seepage of roof slab including covering at junction till guarantee period. (vii) Plastering (a) Rectification of structural / superficial cracks if any. (b) Rectification of protruding / peeling off plaster if any. (c) Rectification of efflorescence (viii) Flooring (a) Rectification of sinking portion of plinth protection including saucer drain. (b) Settlement of foundation & floors, hollow sounding, cracks in tiles/stones. (ix) Plumbing / Sanitary fittings (a) Making good of leakage through soil / waste pipe joints. (b) Replacement of looking mirror if found wavy. (c) Rectification of leakage of overhead tanks. (d) Leakage / seepage of sunken floor, blockage of taps / pipes, nonfunctioning of cistern. (x) Finishes (a) Making good of defective / dissimilar patches of painting to match with remaining surfaces, peeling of paint. (xi) Internal Water Supply (a) Repairs / Replacement of defective taps / fittings. (b) Repair to leakage of GI/ SS water pipe lines including joints. (c) Removal of blockage of GI/ SS pipe lines. (xii) Roads (a) Repair of sinked portion of road & potholes, if any (xiii) Sewage (a) Rectification of slope / system if found defective during use. (b) Rectification of major blockage in Sewer lines. (c) Cracks & settlement of sewage lines. (xiv) Drains (a) Repair to Drains. (b) Settlement of Drains (xv) External Water Supply (a) Repairs to installations & fittings. (xvi) General (a) All manufacturing defects of structures / fixtures / fittings / equipment other than listed above including any defects of shrinkage or other faults that appear in the work within twelve months after a certificate of its completion is given by the Engineerin-Charge shall be rectified by the contractor. 1. Acrylic Emulsion Paint Asian (Royale), ICI (Velvet), Berger (Luxol Silk), Nerolac (Allscapes) 2. Premium Acrylic Smooth Exterior Paint Apex Ultima of Asian paints or equivalent. 3. Aluminium Composite Panel Alpolic, Aluco Bond, Reynobond, Euro bond, Al-strong, Aludecor. 4. Aluminium Extrusions Hindalco, Indalco, Jindal. 5. Aluminum Sections Hindalco, Indalco, Jindal. 6. Board & Plywood Duro, Greren, Century. 7. Ceramic/Rectified Tiles First quality tiles of :-Kajaria, Somany, Orient Bell, RAK. HR Johnsons 8. CP fittings Johnson, Jaquar, Marc, Cera. 9. CPVC Pipes Astral Flowguard, Ashirvad 10. Designer coloured cement concrete floor tiles for external used / Concrete paver blocks. Ultra, Nitco or Equivalent. 11. Epoxy Primer & Paints Berger, Pidilite, CICO. 12. Float Glass Modi Float, Saint Gobain, Tata. 13. Flush Doors (ISI Mark only) Green or Century or Equivalent 14. Galvanized/Stainless Steel Anchor Fasteners Arrow, Hilti, Fischer, Hatticth 15. Gun Metal Gate Valve Zoloto, Leader, SAINT 16. Gypsum Board False Ceiling Boral Gypsum, India Gypsum, USG, St. Gobain(Gyproc) 17. Hardner Hard crete of Snowcem India, MC Deritop F.H. 18. Hydraulic Door Closer Hardwyn, Godrej, Dorma. 19. Hydraulic Floor spring Hardwyn, Godrej, Dorma. 20. Laminate Greenlam, Decolam, Century, Formica. 21. Melamine Polish Melamine Gold of Asian Paint, Wudfin of pidilite, Timbertone of ICI Dulux. 22. M. S. Pipe Electro Steel, Apollo (ISI). 23. Marine Plywood / BWP Ply Century, Green, Duro 24. Oil Bound Distemper Asian (Tractor), ICI (Maxi lite), Berger(Bison), Nerolac (NAD) 25. Sanitary fittings Parryware, Hindware, Cera, Johnson, Somany 26. Plastic Connection Pipe Parryware, Kamal Delux. 27. Ply Wood Kitply, Green ply, Century 28. Pre-coated GI sheet for roofing Jindal Saw, Tata Blue Scope. 29. Polymer Modified Cementitious grout Bal-Endura, Pidilite, Ceco. 30. Pre-laminated Particle Board IS : 12823 (Gr-I, Type-II) Action TESA, Kitlam, Archid Ply, Asis, Green Lam 31. Primer Asian, ICI DuLux, Nerolac 32. PVC Rain Water Pipe & Fitting IS:13592 Type A Finolax, Supreme, Plasto. 33. PVC Shutter Rajshri, Sintex, Akal America. 34. PVC Tank (ISI Marked) Sintex, Star, Lotus, Plasto, Supreme. 35. R. C. C. Pipes (NP-2) ISI Make 36. Solid Plastic Seat Cover for EWC EWC standard seat cover white of Perryware/Hindware/ Neycer, Cera. 37. Stainless Steel Jindal Stainless Steel, Salem Steel 38. Stainless steel Sink with or without Draining board. Nirali, Hindware, Frankee, Cobra 39. Structural Silicon Sealant Dow Corning, Wacker, GE. 40. Structural steel section TATA, SAIL, RINL, Jindal. 41. Synthetic Enamel Paints ICI(Dulux),Asian (Apcolite),Berger (Luxol),Nerolac (NST) 42. Textured Exterior wall paint Snowcem, ICI dulux, Asian. 43. Towel Ring/Towel Rod/Towel Rack. Marc, Jaquar, 44. Tubular Section Windows M/S classic Engineers & Fabricator, Raipur, M/s JK Enterprises, Jaipur. 45. TMT Bars As per criteria laid down in Para 4.3 of Part-B 46. Vitrified Tiles First quality full body tiles of Orient Bell, Kajaria, RAK Ceramics, Johnson, NITCO, RESTILE. 47. Waste Pipe Kamal with brass checknut,Viking 48. Water Proofing Compound (Liquid) Pidiproof Ltd., Sico, Impermo 49. Wire mesh Sterling, Trimurty welded mesh. 50. White Cement JK, Birla. 51. Wall Putty JK, BIRLA 52. Work Stations/ Modular Furniture Godrej, Wipro 53. Stoneware pipe and Gully Trap Perfect or equivalent 54. PVC flushing System Parryware, Johnson, Commander 55. Tactile Tiles Johnson or equivalent 56. Plastic Emulsion Paint Asian, ICI, Berger, Nerolac 1 CEMENT CONCRETE (CAST IN SITU) 1.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1.1.1 1:2:4 (1 cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 1 cum 7878.50 7879.00 1.1.2 1:5:10 (1 cement : 5 coarse sand (zone-Ill) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 2 cum 6518.60 13037.00 1.2 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1.2.1 1:2:4 (1 Cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 1 cum 9895.20 9895.00 2 REINFORCED CEMENT CONCRETE 2.1 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement: 2.1.1 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) 1 cum 10852.95 10853.00 2.2 Centering and shuttering including strutting, propping etc. and removal of form for 2.2.1 Lintels, beams, plinth beams, girders, bressumers and cantilevers 10 sqm 736.40 7364.00 2.3 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 2.3.1 Cold twisted bars 100 kg 107.85 10785.00 3 MASONRY WORK 3.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 3.1.1 Cement mortar 1:6(1 cement :6 coarse sand) 1 cum 7132.25 7132.00 3.2 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : 3.2.1 cement mortar 1:4(1 cement :4 coarse sand) 1 sqm 905.05 905.00 3.3 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 3.3.1 Cement mortar 1:4(1 cement :4 coarse sand) 68.56 sqm 1123.80 77048.00 3.4 Extra for providing and placing in position 2 Nos 6 mm dia. M.S. bars at every third course of half brick masonry. 68.56 sqm 104.80 7185.00 4 STONE WORK 4.1 Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like. 4.1.1 Cement mortar 1:6(1 cement :6 coarse sand) 52.5 cum 9275.45 486961.00 5 CLADDING WORK 5.1 Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3(1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 81.63 sqm 1267.95 103503.00 6 WOOD AND P. V. C. WORK 6.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). 6.1.1 Sal wood 0.4 cum 116520.30 46608.00 6.2 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 6.2.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 15.54 sqm 3473.85 53984.00 6.3 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 6.3.1 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 4 sqm 2172.10 8688.00 6.4 Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 6.4.1 35 mm thick shutters 6.4.1.1 With ISI marked stainless steel butt hinges of required size 6.4.1.1.1 Kiln seasoned and chemically treated hollock wood 3.78 sqm 3792.75 14337.00 6.5 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 6.5.1 Fixed to openings /wooden frames with rawl plugs screws etc. 300 kg 238.35 71505.00 6.6 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. 10 each 854.65 8547.00 6.7 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 6.7.1 250x10 mm 10 each 115.15 1152.00 6.7.2 150x10 mm 15 each 82.55 1238.00 6.8 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 6.8.1 125 mm 8 each 66.25 530.00 6.9 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 6.9.1 Twin rubber stopper 10 each 72.35 724.00 6.1 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 6.10.1 1.0 mm thick 30 sqm 897.30 26919.00 6.11 Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. 6.11.1 With 12 mm mild steel U beading 30 sqm 1228.00 36840.00 6.12 Providing and fixing Pre-laminated medium density fibre board IS: 14587:1998 marked, with one side decorative lamination other side balancing lamination Grade-I (exterior grade) in shelves with screws and fittings wherever required, edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand (fittings to be paid separately). 6.12.1 Pre-laminated with decorative lamination one side and other side balancing lamination exterior Grade - I MDF Board 18 mm thick conforming to IS:14587 30 sqm 1415.70 42471.00 6.13 Providing and fixing 19 mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS : 710 of approved brand boxes,shelves,racks,almirah,cupboard and drawer etc. including necessary nails,screws etc. complete as per direction of Engineer-in- charge. 20 sqm 2593.15 51863.00 6.14 Providing and fixing stainless steel sof closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge. 20 each 272.00 5440.00 6.15 Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per direction of Engineer- in-charge, 16 one set 885.10 14162.00 6.16 Providing and fixing ready made 304 grade stainless steel Modular kitchen basket and accessories such as right angle basket (Plain Cup & Saucer, plant, Partition, Bottle rack, Thali, Cutlery) kitchen utensil basket, Dinner set basket, kitchen grain basket, Multipurpose basket as per site requirement including finishing (wherever required) and fittings. The same shall be fixed with necessary stainless steel nuts & bolts, Stainless Steel screws & telescopic channel etc. as per direction of Engineer-in- charge. (For payment purpose only weight of Stainless steel basket shall be considered excluding weight of all fixing accessories such as nuts, bolts, fasteners telescopic basket channels etc. Payment of providing and fixing telescopic channel shall be paid separately) 75 kg 533.25 39994.00 7 STEEL WORK 7.1 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, bufing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 30 kg 772.40 23172.00 8 FLOORING 8.1 Precast terrazo tiles 22 mm thick with graded marble chips of size upto 12 mm, laid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement:4 coarse sand) : 8.1.1 Ordinary cement without any pigment 40 sqm 1386.80 55472.00 8.2 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 24.41 sqm 1096.55 26767.00 8.3 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 8.3.1 Polished Granite stone slab of colour Black, Cherry/Ruby Red or equivalent 15 sqm 4481.30 67220.00 9 ROOFING 9.1 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 9.1.1 110 mm diameter 50 metre 377.40 18870.00 9.2 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansion. 9.2.1 Bend 87.5° 9.2.1.1 110 mm bend 16 each 150.35 2406.00 10 FINISHING 10.1 12 mm cement plaster of mix: 10.1.1 1:6 (1 cement: 6 coarse sand) 95.64 sqm 343.65 32867.00 10.2 15 mm cement plaster on rough side of single or half brick wall of mix: 10.2.1 1:6(1 cement: 6 coarse sand) 80.67 sqm 395.35 31893.00 10.3 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour: 10.4 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 10.4.1 Two or more coats on new work 50 sqm 155.90 7795.00 10.5 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 250 sqm 156.05 39013.00 10.6 Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. 10.6.1 Two coats 350 sqm 137.45 48108.00 10.7 Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. 10.7.1 With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre 250 sqm 73.95 18488.00 10.8 Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 250 sqm 25.15 6288.00 10.9 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade 10.9.1 Old work (Two or more coats applied @ 1.43 V/ 10 sqm) over existing cement paint surface 250 sqm 131.30 32825.00 11 REPAIRS TO BUILDING .... more in document
