Tender For Special Repairs To Bldg No. P-65, P-66 And P-12 (01 To 08) Of 116 Engr Regt Under Ge (East) Bareilly.; 1 Taking down cement plaster including racking out joint, hacking for key & Scrubbing down with water etc complete all as specified and directed. 2 Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 3 Dismantling of stone slabs and tiles of any description or thickness in floors, aprons Laid, bedded and pointed in any mortar etc. complete all as specified and directed. 4 Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove complete all as specified and directed. 5 Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level complete all as specified and directed. 6 Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed. 7 Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. 8 Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed. 9 Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed. 10 Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each and removing from site complete all as specified and directed. 11 Taking down shutter and refixing with easing in same openingof any description exc. 1 sqm but n.exc 2 sqm each complete all as specified and directed. 12 Dismantling of 100mm bore cast iron/ PVC drain pipe alongwith fittings and accessoriesjointed in cement mortar and taking out from walls, floors or fromtrenches, if required complete all as specified and directed. 13 Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed. 14 Dismantling of 75mm bore cast iron / PVC drain pipe alongwith fittings and accessoriesjointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed. 15 Taking up or down15 mm steel tubingand connections including cleaning for refixing or removal complete all as specified and directed. 16 Taking up or down 20 mm steel tubingand connections including cleaning for refixing or removal complete all as specified and directed. 17 Dismantling water tankscapacity of 500 & n exc 1000 and removing to store of all retrieved material complete all as specified and directed. 18 M&L for 15mm thick rendering in cement mortar 1:4 to brick masonry wall surfaces or on other than fair faces of brick wall surfaces finished fair & even without using extra cement for fixing tiles etc complete all as specified and directed. 19 M&L for 25 mm thick PCC 1:2:4type B0, using 12.5mm graded stone aggregate as in floors toreceive surface of tile complete all as specified and directed. 20 M&L for screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed. 21 M&L for screed bed or bedding layer of mortar, 20 mm thick, in cement mortar 1:6, for laying floor finishes/tiles complete all as specified and directed. 22 M&L for non- skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed. 23 M&L for non skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular )area of each tiles exc 0.18 sqm but not exceeding 0.38 Sqm in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match with coloured tiles complete all as specified and directed 24 M&L for non skid ceramic tiles 7 to 8 mm thick (square / rectangular )area of each tiles exc 0.18 sqm but not exceeding 0.38 Sqm on vertical surfacesetc set and jointed in neat cement slurry and pointed in coloured cement to match with colouredtiles complete all as specified and directed. 25 M&L for 7 to 8 mm thick glazed coloured ceramic tiles (square/ rectangular) with border , area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed. 26 M&L for 20-25mm thick machine cut kota stone pre-polished as in riser and spets, skirting in full length in single peice without joint, with groove cutting in double line of sir width laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. 27 M&L for machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. 28 M&L for green Marble work 25mm thick, (table rubbed and polished) in treads and riserand like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed. 29 M&L for 20 mm thick Granite of black colour (table rubbed and polished) as in windows cill &cooking platforms and like over and including 15mm cement mortar (1:4) screed bed including form work, pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with full round bull nosing edging complete all as specified and directed. 30 M&L for 75mm thick PCC 1:3:6 , type C-2 using 40 mm graded stone aggregate as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length.Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed . 31 M&L for 100 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base floor/ pavings complete all as specified and directed. 32 M&L for 75 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base floor/ pavings complete all as specified and directed. 33 M&L for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed. 34 M&L for cement Concrete coloured interlocking paver blocks shall be factory made with casting in rubber/pvc moulds & compacting on a vibro table assembly and shall be cured in curing tank for atleast 14 days and then air dried before use. The paver block shall be confirming to IS 15658 -2006 of60mm thickness, M-35 Grade. Approved design, shape, size and colour of top layer complete all as specified and directed. 35 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed. 36 M&L for reinforced cement concrete 1:1.5:3 (20 mm graded aggregates) (nominal mix) as in slabs supported on wall like including bonding agent, as in slabs supported on wall,landing, balconies, shelves and like including bonding agent complete all as specified and directed. 37 M&L for form work to chajja, weather shade, troughs and similar items includingedges for rough finished surfaces of concrete flat complete all as specified and directed. 38 M&L for form work to edges of concrete flats, treads, breaks in floors window cill, concrete railing opening in conc wall , floor and roof n.exc 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n.exc 20cm wide for rough finished surfaces of concrete complete all as specified and directed. 39 S&F TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) but not less than 0.9 mm dia conforming to Fe-410 - 0 complete all as specified and directed. 40 M&L for PCC (1:2:4) type B-0 using 12.5 mm graded stone aggregrate laid over roof, kerbs or mud stops, rounded or chamfered on edges slab after applying cement slurry for filling undulationations finished even and smooth without using extra cement complete all as specified and directed. 41 M&L for 15 mm thick screed bed or bedding layer in cement mortar 1:4, over RCC roof slabs for laying water proofing treatment mixed with using water proofing liquid @ 150 ml per 50 Kg bag of cement complete all as specified and directed. 42 supply Integral water proofing Liquid complete all as specified and directed. 43 M&L for PCC 1:5:10 type E-2 40 mm graded stone aggregate as sunken sub base of floor fillings complete all as specified and directed. 44 S&F 32mm dia GI pipe, medium grade as in spout pipe in sunken floor complete all as specified and directed. 45 M&L for brick work with fly ash bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as specified and directed. 46 M&L rendering 15 mm thick in CM 1:6 on brick masonary wall surfaces or on other than fair faces of brick masonry finished even and smooth witout using extra cement complete all as specified and directed. 47 M&L for rendering 10mm thick in cement mortar (1:4), and 5 mm thick setting layer in CM1:3 finished even and smooth using extra cementto on brick masonary wall surfaces or on other than fair faces of brick masonaryfinishedeven and smooth without using extra cement with using water proofing liquid @ 150 ml per bag of cement complete all as specified and directed.(Note : Water proofing liquid shall be measured and paid separately) 48 M&L for rendering 5 mm thick in CM 1:3as on concerete surface on ceilings finished even and smooth without using extra cement complete all as specified and directed. 49 M&L for applying cement slurry over existing roof surface @ 3 Kg/ Sqm including mix with water proofing liquid @0.15 ltr per 50 Kg cement bags as per manufactures instruction complete all as specified and directed. 50 S&F APP polymeric water proofing membrane, minimum 3mm thick and weighing above 3.0 Kg/Sqm with rich bitumen and select polymers blended to obtain excellent heat resistant& cold resistant, black finish reinforced with non-wovenpolyester matt, with a thermo fusable finish laid over compatible bitumen primer torching overlaps with a propane or a butane gas torch, with a overlap of 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions completed including removal of existing treatment all as specified and as directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 85/25 confirming to IS-73, applied@1.20 Kg/Sqm over a coat of bituminous primer confirming to IS-3384 applied @ 0.40 Kg/Sqm(ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii)The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv)In case of stone masonry parapet wall etc a groove of size 25mmx25mm(minimuim) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimny/other vertical surfaces and polimeric membrane insterted in groove and sealed with paving bitumen (v) Exposed surfaces of APP membrane shall be applied with one coat of bituminous aluminium paint @ 150 ml/Sqm. (vi) Above aspects are deemed to be included in quoted rate. 51 M&L for WPT in sunken floors as described here under:- Sunken floor and sides up to finished floor level shall be plastered with 15 mm thick cement plaster in CM 1:4 mixed with water proofing liquid @ 150 ml per bag of cement . (ii) Preparing plastered surfaces and providing APP polymeric water proofing membrane, minimum 4mm thick and weighing above 4.0 Kg/Sqmmembrane with rich bitumen and select polymers blended together to obtain excellent heat resistance & cold resistant by Dr fixit or super thermolay manufactured by as approved by GE, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over compatible bitumen primer at the rate of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturers instructionsincluding preparation of surface by removing the existing treatment, complete all as specified an as directedNote :-(i) Polymeric membrane shall belaid in sunken floor and on sides up to finished floor level.(ii)The waterproofing treatment shall be got carried out by the manufacturer or their authorised applicators. (iii)Above aspects are deemed to be included in quoted rate. (iv) Supply only water proofing liquid shall be measured and paid seperately 52 M&L for cool roof antislip tiles 300x300x10 mm with high SRI value not less than 90 laid over existing treatment on accessible roof and including 15mm thick screed bed in CM 1:4 complete all as specified and directed. 53 S&F for Pressed steel frames Size 125mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., complete all as specified and directed 54 S&F factory made WPCdoor frame 100% Solid(wood polymer composite) suitableSize Rebated ,made from wpc material comparising of virign PVC polymer of K value 58-60 (suspension grade ) calcium corbonate and natural fibers ( wood powder/rice husk /wheat husk)minimum compressive strength of 58 N/mm2, moduus of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite / borer proof, water / moisture proof & fire retardant & fixed in postion with SS dash fasterns / hold fast of required dia and length,colour of door frame to match that of shutter all as per specifications drawings complete all as specified and directed 55 M&L for in repair 2nd class hardwood, Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and directed. 56 S&F flush shutters, 40 mm thickness solid core construction, with block board core and plywood face panels, commercial type on both sidesFace is covered with decorative face veneer with lipping/frame to match complete all as specified and directed. 57 S&F 35mm thick 2nd class hardwood factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed. 58 S&F 150 mm long floor door stopper of aluminium alloy body and tongue, brass body and tongue with hard drawn steel spring fixed in floor complete all as specified and directed. 59 S&F 18 mm thick termite resistant and water proof, both side prelaminated wooden plywood one side with decorative choice lamination, and other side plain white lamination total thickness not more than 22 mm thick, as in cup board shutters, with wardrobe/ finch lock & PVC lipping on all exposed edges of same texture and shade, withcomplete all as specified as directed. Note:1) Design & layout of wardrobe and pattern / colour of lamination to be approved by GE. 2) thickness of laminated not less than 1mm for inside plain white type & 1.5 mm for outer decorative type. The laminate shall be fixed to base with approved adhesive as per manufacturers instructions and machine pressed to ensure proper bonding with base ply and avoid air pockets. 3) Frame to be fixed to walls, soffits & base of cupboard with fasterners complete all as specified and directed. 60 S&F aluminium powder coated frame hollow sections members of size 63.50 mm x38mmx 1.48mm thick,4 mm thick aluminium composite panel LDPE core with PET coating fixed with into the wall for kithen cabinet/ cupboard shelf incl hanging self for clothes with aluminium clip/strips, pvc beadings fixed with adhesive on edging , design as per site requirements basis, complete all neccessary fitting complete all as specified and directed. 61 S&F solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick single side prelam PVC sheet used instead of Plain colour PVC sheet , suppling & fixing in opening as per specification & drawing complete all as specified and directed. 62 S&F 30 mm thick factory made both side Prelam PVC sheet used instead of Plain colour PVC sheet. Stile and rails feathered at edges consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C channel heaving aPanelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed. 63 S&F mild steel window grills box typeframed work as in window guard bars, grills or forged into spikes, framed balusters, walkway railing and similar work including welding complete FE-290 grade E-165 complete all as specified and directed. 64 S&F Powder coated aluminium sliding windows frame with movable shutter ( sliding on minimum two PVC roller of best quality, for each shutter on threetracks with stainless steel mosquito proofing and glazing shutter and incl 5.50 mm thick glass & stainless steel wire mesh fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below- (i) Window frame :68.4x38mm X 1.15 mm thick for three tracks.(ii) Top/bottom rail and style / rail of shutter : 15x37.5x1.15 mm thick and over.(iii) Aluminium beading - 0.7mm thick(iv) stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperature 1.40mm and fixed in aluminium window or alongwith F/Y section fixed with aluminium wire staples complete.(v)Aluminiumfittings suchaluminium suitable handle with auto interlock cap with suitable size .(vi) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed. 65 S&F Powder coated aluminium sliding windows frame with movable shutter (sliding on minimum two PVC roller of best quality, for each shutter on threetracks with stainless steel mosquito proofing and glazing shutter and incl 5 mm thick glass & stainless steel wire mesh fixed with neoprene rubber gasket with aluminium beading, clips, frame made with aluminium section as appended below- (i) Window frame :95x38mm X 1.15 mm thick for three tracks.(ii) Top/ bottom rail and style / rail of shutter : 15x37.5x1.15 mm thick and over. (iii) stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperature 1.40mm and fixed in aluminium window or alongwith F/Y section fixed with aluminium wire staples complete.(iv)Aluminiumfittings suchaluminium suitable handle with auto interlock cap with suitable size .(v) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed. 66 S&F Powder coated aluminium ventilators box type with louvers & wire mesh fixed with neoprene rubber gasket, aluminium beading, clips. Frame made with powder coated aluminium section of size as appended below (i)frame :45.2mm x35mm X 1.15 mm(ii) Aluminium beading - 0.7mm thick(iii) Glass louvers depth 6 inch. Blade Angle: 38 degrees and thickness of blade 2.02 mm with 106.25 mm spacing.(iv) Aluminium neccessary fittings complete as required.(v) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed. 67 S&F Powder coated aluminium sliding windows and frame with movable shutter (sliding on minimum two PVC roller of best quality on two tracks Aluminium composite panel shutter fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below-(i) Window frame :68.4x38mm X 1.15 mm thick for two tracks.(ii) Top/bottom rail and style / rail of shutter : 15x37.5x1.15 mm thick and over.(iii) Aluminium beading - 0.7mm thick(v)Aluminiumfittings suchaluminium suitable handle with auto interlock cap with suitable size .(vi) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed. 68 S&F Powder coated aluminium sliding windows and frame with movable shutter (sliding on minimum two PVC roller of best quality on two tracks Aluminium composite panel shutter fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below-(i) Window frame :45.2x35mm X 1.15 mm thick for two tracks.(ii) Top/bottom rail and style / rail of shutter : 15x37.5x1.15 mm thick and over.(iii) Aluminium beading - 0.7mm thick(v)Aluminiumfittings suchaluminium suitable handle with auto interlock cap with suitable size .(vi) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed. 69 S&F powder coated aluminium ventilator box type with louvers & wire fixed neoprene rubber gasket, aluminium bading, clips. Frame made with powder coated aluminium as appended below-(i) Window frame :45.2x35mm X 1.15 mm thick for two tracks(ii) Aluminium beading - 0.7mm thick(iii)Glass louvers depth 6 inch. Blade angle 38 degree and thickness of blade 2.02 mm with 106.25 mm spacing.(iv) Aluminium necessary fittings complete as required.(vi) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed. 70 S&F 18 mm thick imported wooden medium density fibreboard fixed with frame including hold fat (as in shutter including knob in each shutter) etc. including magnet catcher built in cup board with all necessary fitting complete all as specified and directed. 71 S&F magnet catch with striking plate including letting in and fixed complete all as specified and directed. 72 S&F 300 mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed. 73 S&F 150 mm thick Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed. 74 S&F 150mm size aluminium handles, cast type anodised completed all as specified and directed. 75 S&F 100 mm size butt hinges medium weight stainless steel colled rolledcomplete all as specified and directed. 76 S&F in repair 300mm size ordinary mild steel , rat tailed rod pattern spring including roller and roller platewelded to mild steel frame complete all as specified and directed. 77 S&F 300 mm long aluminium sliding door bolts plate type with bright bolt not less than 16 mm dia with and including a minimum of 6 bolts and nuts, 04 Nos on bolt plate and 02 Nos on staple plate and fix complete all as specified and directed 78 S&F hydraulic concealed hinge with clip on installation and integrated Silent System, opening angle not less than 100º, For shutter thickness 15 - 24 mm full overlay type shutters, hinge cup dia 35 mm including necessary fixing arrangement with SS screw complete all as specified and directed. 79 S&F 200 mm long stainless steel glossy finish handles with SS screw complete all as specified and directed. 80 S&F stainless steel wire cloth, 0.56 mm nominal dia of wire and average with of aperture 1.18 mm and fixed with stainless steel wire staples complete all as specified and directed. 81 S&F 1000 litres, rotational moulded polyethylene of white colour in tripple layer water storage tank (cylindrical vertical with closed top with suitable size ofM S cover with suitable locking system ), hoisted and fixed in position complete all as specified and directed. 82 S&F 20mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. 83 S&F 15 mm bore dia steel water tubing galvanized medium grade concealed in all type wallwith all fittings, fixed to walls and ceiling or in floor complete all as specified and directed. 84 S&F 20 mm bore dia steel water tubing, galvanized, medium gradeconcealed in all type wallwith all fittings,fixed to walls and ceiling or in floor complete all as specified and directed. 85 S&F in repair brass chromium plated wall mixer 2 in 1, 15mm for mixing hot & cold water screwd down three joints to steel pipes or unions and plugging and screwed to walls complete all as specified and directed. 86 S&F in repair fancy type 15mm dia chromium plated fancy type wall mixer hot & cold with long swan for kitchen sink fixing and connection to pipes complete all as specified and directed. 87 S&F in repair fancy type 150mm size square brass CP shower rose complete all as specified and directed. 88 S&F in repair 15 mm dia bib tap fancy type chromium plated with flange quarter turn complete all as specified and directed. 89 S&F 15 mm bore dia fancy type chromium plated brass two way bib cock complete all as specified and directed. 90 S&F in repair 15 mm dia bib tap cast copper alloy with butterfly handle , screwed down for iron pipe or for brass ferrule and fixed complete all as specified and directed. 91 S&F in repair vitreous china coloured wash hand basin with pedestal 55x45x82 cm complete including fancy CP pillar tap, CP Waste coupling, waste pipe, complete fixing arrangementand cutting for and pinningin walls & making good complete all as specifed and directed. 92 S&F stainless steel of AE - SI 316 grade tubulartowel ringincluding a pair ofCP brass bracket complete all as specified and directed. 93 S&F in repair tubular towel ring including apair of CP brass bracket complete all as specified and directed. 94 S&F in repair 15mm bore PVC connections, with PTMT nuts of length 450mm complete all as specified and directed. 95 S&F in repair fancy type brass chromium plated soap dish of 160x160x90 mm complete all as specified and directed. 96 S&F in repair fancy type chromium plated brass angle valve type suitable for 15mm bore pipe complete all as specified and directed. 97 S&F in repair fancy type stainless steeltowel racksize 600mmincluding a pair of brass bracket complete all as specified and directed. 98 S&F chromium plated brass tubular towel rail 20 mm dia, D type for wash hand basin centre holed fixed to iron pipe complete all as specified and directed. 99 S&F in repair fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with CP bracket gaurd and railling 60 cm long complete all as specified and directed. 100 S&F in repair fancy type glass corner 300mm radius of 10mm thick toughned glass with CP railing fixed with screws fancy type complete all as specified and directed. 101 S&F in repairs of 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 102 S&F in repair 15 mm dia fancy type stop cock , chromium plated with long shank and cup (conncelaed type) for iron pipe or for unions and fixed complete all as specified and directed. 103 S&F in repair vitreous china squatting pan of orrissa pattern long pan size580 x 440 mm white with Por S trap size100 mm dia front or back inlet and integral foot rest any pattern (excluding flushing cistern and flush pipe) including provn of lime concrete bedding complete all as specified and directed. 104 S&F in repair PVC low level flushing cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed 105 S&F brass CP health faucet with 8mm dia 1.0 meter long flexible tube and wall hook screwed for iron pipe fancy type log body complete all as specified and directed. 106 S&F in repairPVC (SWR) multifloor trap with grating including jointing with solvent cement floor trap 75 mm dia outlet plain with grating including jointing to waste pipe fixed in cement concrete 1:2:4, typeB-1 complete all as specified and directed. 107 S&F in repair PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floorwith necessary fitting complete all as specified and directed. 108 S&F in repair PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floorwith necessary fittingcomplete all as specified and directed. 109 S&F PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floorwith necessary fitting complete all as specified and directed. 110 S&F PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floorwith necessary fittingcomplete all as specified and directed. 111 S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed. 112 S&F PVC (SWR) 75mm bore bends any radiuscomplete all as specified and directed. 113 S&F PVC (SWR) 75 mm bore junction single (Single T) equal or unequal with access doorcomplete all as specified and directed. 114 S&F PVC (SWR) 110 mm bore junction single (Single T) equal or unequal with access doorcomplete all as specified and directed. 115 S&F designed looking mirror size exc 0.54 sqm to 0.75 sqm of selected quality 6mm thick glass, mounted on fixed to wall with CPplugs with chromium plated brass screws and cup washers complete all as specified and directed. 116 S&F PTMT alloy toilet cabinet with mirror overall sizee 350x450 mm complete all as specified and directed. 117 S&F in repair stainless Steel plate rack of size 90x80x25cm made with 1.00 mm thick sheet including taking out existing wooden plate rack complete all as specified and directed. 118 S&F 0.8 mm thick stainless steel kitchen sink size 590x460x230mmundermount, single bowl (bowl size 540x410x230 mm), including waste pipe & SS coupling complete all as specified and directed. 119 S&F in repair 20 mm dia stainless steel 1.0 mm thick fancy typedroppery rod with decorative design matching brackets as approved and knobs (lattu) or end bracket as required incl fitting with 80 mm long SS screw with 75 mm long wooden gitty of appropriate c/s in each end & intermediate support complete all as specified and directed. 120 S&F mild steel rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding door,Fixed with angle cleats or other connecting plates complete all as specified and directed. 121 S&F rolled mild steel Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed. 122 S&F Pre-coated galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed. 123 M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges ofsunshades, shelves, lintels, Chajja (up to IInd floor) etc making good, cutting out exc 10cm and not exc 40cm girth in RCC chajjas in brick walls complete all as specified and directed. 124 M&L for dubbing coat on exposed cement concrete 10 to 20 mm thick in CM 1:4 incl micro concrete with chicken wire mess with water proofing liquid @200 ml per bag up to II nd floor roof level complete all as specified and directed. 125 Dismantling of concrete by chiseling from RCC members like column , beam, parapet facia, chajja, ceiling,etc exposingthe reinforcement without disturbing the reinforcement free from rust by sand blasting/using chemical , apply a coat of rustolin to remove rust and acralic polymer on old rusted reinforcement proving at places addl reinforcement welding with existing reinforcement as directed wherever required binding RCC 50 mmx50 mm (10 mm gauge welded mesh ) & tack , securing with clips / blinding wire, welding & provision guniting pressure 2.2 to 2.5 kg /sqm with admixer 1 cement 3.5 of sand of thickness 25 to 40 mm including stripping floating with wooden strippers for proper dimension control neccssary form work & scaffolding up to three storey and including height of head room complete surface of guniting to be finished fair with 10 mm thick plaster in cement mortar 1:4 with water proofing compound @3% by weight of cement and construction fibre as per manufacturer instruction cleaning & removing of waste meterial etc as dirply two coat of water proofing liquid new coat ezee at interval of 8 hours cure for thesurfaces complete all as specified and directed. 126 S&F 0.71mm thick Aluminium plain sheeting Alloy 31000 H4, stucco embossed finish withfixed with coach screw and Aluminium washer in roof and wall etc. with end laps stitched with 25x6mm G.I. bolts at 20cm apart gap to be with thermocol sheet including dismantling complete all as specified and directed. 127 M&L for preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coatof red oxide zinc chrome primer complete all as specified and directed. 128 M&L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coatof pink primer complete all as specified and directed. 129 M&L for preparation of old painted wooden or wood based surfaces of any description n.exc 10 cm in width or girth when unconnected with other painting or when painted in a diferenttint and applying one coat of synthetic enamel paint over and including one coat of red oxide complete all as specified and directed. 130 M&L for complete removal of existing treatment on wall by scrapping with mechanical sander (having mechanical vaccum mechanism ) with sanding pad of appropriate grit to make surface clean ,free from dust ,loose paint etcby skilled labour and applying two coat OBD on wall with airless electric sprayers over a coat of primer applied using airless electric sprayer over one coat of plaster of paris of 1mm thickness complete all as specified and directed.Note:-Application to be done through authorised applicator of manufacturer. 131 M&L for praparing newly plastered surface and applying two coats of dust resistant and anti algal weather proof exterior emulsion paints over a one coat of wall care putty complete all as specified and directed. 132 M&L for two coat OBD on newly plastered wall surface with airless electric sprayers over a coat of primer applied using airless electric sprayers over two coats of wall care putty of 1mm thickness complete all as specified and directed. Note-Application to be done through authorised applicator of manufacturer 133 M&L for complete removal of existing treatment on ceiling,etc including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying two coats ofwhite wash complete all as specified and directed. 134 Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided complete all as specified and directed. 135 M&L for preparation of new surface of plastered and applying of two coats OBD on ceiling with airless electric sprayers over a coat of primer applied using airless electric sprayers over and including 1 mm thick plaster of paris (approved by GE) prepared and sanded with electrically operated sanding machine. Application to be done through the authorised applicator of manufacturer complete all as specified and directed. 136 M&L for applying two coats of white putty on new surface and applying one coat of exterior water based primer by using Airless spray techonology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose lengthof 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressue and paint usage and certified by jpaint manufacturer and as mentioned in PS and accessories fpr applying distemper, should be able to spray in hard to reach areas and penetration of distemper, on the surface to achieve excllent application using limited manpower complete all as specified and directed. 137 M&L for complete removal of existing treatment, preparation of old decorated plastered or unplastered surfaces of walls / roofprojections including facia,cornices etc. and applying two coats of white putty and applying one coat of primer by using Airless spray techonology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose lengthof 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressue and paint usage and certified by paint manufacturer and accessories for applying Primer, should be able to spray in hard to reach areas and penetration of Primer, on the surface to achieve excllent application using limited manpower complete all as specified and directed. Note : - Sanding of old decorated surface to be done by mechanical sander with 1500 - 2700 rpm, with internal dust extraction system for clean environment certified by paint manufacturer. 138 M&L for applying two coats of exterior weather proof 100% anti fungal acrylic smooth emulsion with silicon additives that offer anti algae high performance exterior wall finishapplied by using Airless spray technology with max working pressure of 3300 PPSI and capable of operating single spray gun with a max material hose length of 30 mtr the spray machine should be of reputed manufacture with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and accessories for applying exterior weather proof paint, should be able to spray in hard to reach areas and penetration of exterior weather proof paint on the surface to achieve excellent application using limited manpower complete all as specified and directed. 139 M&L for complete removal of existing treatment on surface of wall including cleaning the surface throughly by using wire brushes and removing used materials from the surface and applying two coats of dust resistant and anti algal weather proof exterior emulsion paints over a one coat of wall care putty complete all as specified and directed. 140 M&L for preparing newly plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed. 141 Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete with fittings and fixtures such as switches, ceilingroses, pendants, regulators, socket, lamp holders brackets, bulk head fittings, tube light fittings etc complete and removing allretrieved materials toMES storesfor segregation of serviceable /Unserviceable fitting&fixture and also making good disturbed surfaces of wall, floors etc complete all as specified and directed. 142 M&L concealed point wiring complete with single core FRLS PVC insulated, unsheathed, multi stranded copper conductor cables 1.5 Sqmm 1100 volts grade, with and incl 1.5 Sqmm FRLS PVC insulated, unsheathed, multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, complete wiring drawn through &including PVC Conduit (Concealed in wall/ceiling) of size 20mm dia and above (as per conductor run ) medium grade, ISI marked, incl all accessories & fittings / junction boxes / inspection covers etc, with and incl concealed Modular metal flush box of suitable size flush within wall surface, suitable for fixing of Modular cover plate, switches / sockets etc, complete all as specified and directed for the following :-Note : 1. Modular white cover plate shall be measured and paid separately2. Rate quoted shall deemed to be inclusive of Metal flush box, cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. 143 One light point or one fan point controlled by one switch 144 one 3 pin socket outlet 5 Amp on same board 145 one 3 pin socket outlet 5 Amp on independent board 146 one bell/ buzzer point controlled by one push button on the same board with other switches or independent 147 All as per serial item No 142 here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 2.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and directed. 148 S&F Modular Switch 1 way 16 Amps, 1 Module size complete all as specified and directed. 149 S&F Modular Socket 6 A, 5 Pin 2 Module size complete all as specified and directed. 150 S&F Modular Socket 6A/16 A, 5 Pin ,2 Module size complete all as specified and directed. 151 S&F Modular Switch 1 way 6 Amps, 1 Module size complete all as specified and directed. 152 S&F Modular white cover plate with frame, 1 Module size complete all as specified and directed. 153 S&F Modular white cover plate with frame, 3 Module size complete all as specified and directed. 154 S&F Modular white cover plate with frame,4 Module size complete all as specified and directed. 155 S&F Modular white cover plate with frame, 6/8 Module size complete all as specified and directed. 156 S&F modular fan requlator step type 120 watt, 2 module complete all as specified and directed. 157 S&F modular bell push 6A 1 module complete all as specified and directed. 158 S&F electric call bell ding dong AC 230 vlts single pole complete all as specified and directed. 159 S&F angular lamp holder, metal cased body of brass with back plate including 09Watt LED Bulb inbatten fittings, including Plastic square box of required size complete all as specified and directed. 160 S&F LED Bulb 9 Watt energy efficient color temp 6500k, lumen 825lm operating voltage 220 Volt complete all as specified and directed. 161 Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge. 162 S&F LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. 163 S&FLED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 164 S&F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size. complete all as specified and directed. 165 S&F LED street light luminaire of 35 Watt capacity, made of single piece pressure die-cast aluminium housing with high power LED with lens for proper light distribution luminiaries, IP 66, with toughned glass cover and incl control gear etc, with and including making all electric connection and including bracket, 1.5 mtr long made out of galvanized iron pipe of 40 mm dia size light grade complete with and incl 02 nos MS clamp made of MS flate iron of 50 x 6 mm size with nut, bolts, washer etc with and incl two coats of aluminum paint over a coat of red oxide primer complete all as specified and directed. 166 Taking down MCB Distributing board with MCCB/MCB of any size and capacity complete all as specified and directed 167 S&F sheet Metal enclosure double shutter type for DB’s 240 Volts Single Pole and Neutral 12 way with 200 Amps rated bus bar complete all as specified and directed. 168 S&F sheet Metal enclosure double shutter type for DB’s 240 Volts single Pole and Neutral 8 way with 200 Amps rated bus bar complete all as specified and directed. 169 S&F SPN 40 amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning complete all as specified and directed. 170 S&F SP 5 to 32 amp rating 240V, 10KA B curve miniature circuit breaker (MCB) of Single pole and neutral in the MCB DB complete with connection testing and commissioning complete all as specified and directed. 171 S&F VTPN DB 6 way double door type including MCCB TP 63 Amps as incomercomplete all as specified and directed 172 Taking down submain wiring of size 4/6 Sqmm complete all as specified and directed 173 M&L for concealed sub main wiring with 2 runs of 6 Sqmm FRLS, PVC insulated, unsheathed and stranded copper conductor cable with and incl 6 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn drawn through & PVC conduit of size 25 mm and aboveincl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. incl taking out old wiring and conduitNote : 1. The cost of concealed conduit & accessories is deemed to be included in quoted rates.2. The two 2 runs of 6 Sqmm wire and one run of 6 Sqmm wire will be measured as one unit. 174 All as per item Ser No. 168 above but wiring with 2 run of 4 Sqmm and one run 4 Sqmm complete all as specified and directed. 175 All as per item Ser No.168 above but wiring with 3 run of 4 Sqmm complete all as specified and directed. 176 M&L for earthing complete withgalvanized steel earth plate electrode 60 cmx 60 cm x 6 mm thick buried directlyin ground (earth pit notless than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level,connecting to theGalvanized ironearth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron andsteelearth wire protected by provision of GI lightgrade pipe15 mmbore including provision of concrete pitmade from PCC ( 1:2:4) type B-1 (using20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angleiron40 x 40 x 6 mm and handle of 6 mmdia MS barmade to shape, GI light grade 20 mmbore pipefor watering perforated atbottom, 1.50metre long placed on top edge of earth plate, common salt &charcoalfilling, withfixing arrangement , funnel, wire mesh and earthwork in hard/dense soil, returning filling in and removal of surplus soilto a distance notexceeding50 metres, all as perelectrical plateNo 5 of SSR 2009 Part-I and connecting toMCBDB’searth test point all as specified or indicated including testing on completion complete all as specified and directed. 177 S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed. 178 S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm including taking down old fan and depositing to MES store complete all as specified and directed. 179 S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified and directed. 180 Taking down the old serviceable electric meter 4 Nos and keeping in safe custody including refixing the same including electric wire, flexible pipe and PVC conduit from DB to meter and fixing accessories including sheet metal eclosure made of CRCA sheet 2 mm thickhaving locking arrangement duly painted with two coats of super enamelled paint over a coat of red oxide suitable for mounting on wall and housing 4 Nos electirc meter and 01 No VTPN DB complete all as specified and directed. 181 Taking down the old serviceable electric meter 8 Nos and keeping in safe custody including refixing the same including electric wire, flexible pipe and PVC conduit from DB to meter and fixing accessories including sheet metal eclosure made of CRCA sheet 2 mm thickhaving locking arrangement duly painted with two coats of super enamelled paint over a coat of red oxide suitable for mounting on wall and housing 4 Nos electirc meter and 01 No VTPN DB complete all as specified and directed. 182 S&F ceiling fans BLDC complete with blades, down rods, Modular type electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor complete all as specified and directed. 183 Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store, complete all as specified and directed. 184 S&F in replacement AC functional box MCB protected socket plastic bse dimension 415 x 375x 225 mm 4 module raise neutral link complete with one single pole MCB 20 Amp C series 240 volt complete all as specified and directed. 185 M&L for painting of ceiling fans complete, with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. including, winding and capacitor hanging ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed.
