Tender For Spl Repairs To Bldg No 50 ( 8 X Or Md Accn) In Zone E At Mil Stn Agartala.; 1 Taking out complete existing roof treatment from roof surfaces and roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust and removing rubbish at distance not exceeding 50m as per direction of Engineer-in-Charge complete all as specified and as directed. 2 Material and labour for Cutting out cracks to V-section in existing RCC roofs or terrace, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) complete all as specified and directed.Note: Cutting of grooves will be carried out by using mechanical means like Groove cutter/ wall chaser. 3 Material and labour for 15 mm thick screed bed or bedding layer in CM 1:4 mixed with water liquid proofing compound @ 200 ml per bag of cement on concrete roof surface, finished the surface fair and even to maintain the proper slope of roof surface complete all as specified and as directed.(Note: Liquid WPC shall be measured and paid separately) 4 Material and labour for PCC (1:2:4) type B0 (using 12.50mm graded stone aggregate) mixed with water liquid proofing compound @ 200 ml per bag of cement as in chajjas, rounded or chamfered on edges complete all as specified and as directed.(Note: Liquid WPC shall be measured and paid separately) 5 M & L for cleaning plastered surfaces to receive the water proofing membrane, applying one coat of hot paving bitumen of penetrationvalue 85/25 conforming to IS 73 @ 1.20 kg/sqm over a coat of bitumenous primer @ 0.30 ltrs per sqm and applying a layers of APP based polymeric membrane, 3mm thick (minimum) weight 3.00 Kg/sqm reinforced with polyster non woven fabric (weighing not less than 150 gms/sqm) shall be applied overBitumenious primer (Application of polymeric memberane shall be by torch application, over laps shall be minimum 100mm on the transverse direction & 75 mm on the longtudinaldirection) polymeric membrane shall be taken to a height of 60 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by membrane flashing, coved fillet in PCC (1:2:4) type B-0 of radius 75 mmshall be provided at the junction of roof & other vertical surfaces& surfaces shall be painted with hot paving bitumen of penetrationvalue 85/25 conforming to IS 73 @ 1.20 kg/sqm & applying one coat of aluminium paint over the APP modified membrane @ 0.11 kg/sqm complete all as specified and as directed. 6 Dismantling of AC sheet corrugated / CGI corrugated sheets in roofing any gauge and any thickness including ridge, valley/gutter etc. complete all as specified and directed. 7 Supply and fixing pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws as specified complete all as specified and as directed. 8 Supply and fixing pre-painted galvalume aluminium zinc coating GI based plain steel sheet0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws as specified complete all as specified and as directed. 9 Material and labour for preparation of old steel surfaces over 10cm width or girth and applying one coats of syntheticenamel paint complete all as specified and directed. 10 Dismantlingfloor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceabletiles to store and rubbish off the premises complete all as specified and as directed. 11 Material and labour non skid ceramic coloured tiles7 to 8mm thick (square /rectangular) of premium quality, area of each tile exceeding 0.18 sqm but not exc 0.38 sqm in floors etc.set & jointed in neat cement slurry & pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by AGE(I). 12 Material and labour non skid ceramic coloured tiles7 to 8mm thick (square /rectangular) of premium quality, area of each tile exceeding 0.18 sqm but not exc 0.38 sqm on skiriting/dado, set & jointed in neat cement slurry & pointed with white/coloured to match over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by AGE(I). 13 Material and labour non skid ceramic coloured tiles7 to 8mm thick (square /rectangular) of premium quality, area of each tile exceeding 0.11 sqm but not exc 0.18 sqm in floors etc.set & jointed in neat cement slurry & pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by AGE(I). 14 Material & Labour glazed ceramic coloured tiles 450X 300X 7mm thick of premium quality on skiriting/dado, set & jointed in neat cement slurry & pointed with white/coloured to match over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by AGE(I). 15 M & L for machine cut Kota stone slab flooring using 20 to 25mm thick slabs, laid and jointed with grey cement slurry mixed with a admixture of pigment to match shade of slab including rubbing and polishing to smooth mirror finish all to required sizes, the size and design / pattern of slabs shall be as directed, including diagonals, inlays, borders, margins in two or more shades of slabs including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:3 complete all as specified and as directed. 16 Material & Labourmachine cut kota stone slab as in riser of steps, skirting, dado etc. using 20 to 25mm thick slabs laid and jointed with grey cement slurry mixed with a admixture of pigment to match shade of slab including rubbing and polishing to smooth mirror finish all to required sizes, the size and design / pattern of slabs shall be as directed, including borders, margins in two or more shades of slabsover backing coat of 10mm thick in cement mortar 1:3 complete all as specified and as directed. 17 Material and labour 25mm thick forPCC 1:2:4 typeB-0, using 12.5 mm graded stone aggregate as in levelling course infloor finished even and roughcomplete all as specified and directed. 18 Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. 19 Material & Labour for providing 100 mm thick plain cement concrete 1:3:6 type C-2, using (40 mm graded brick aggregate) as in path or pavement or low laying area surfaces finished even and rough complete all as specified and directed. 20 Material and labour for precast cement concrete chequered tiles of size 300 x 300 x25 mm thick as in floor, set and jointed and pointed with neat cement slurry laid over and including 15 mm thick screed bed or bedding layer in CM 1:4 complete all as specified and directed. 21 Material & Labour for 75mm thick, PCC 1:3:6, Type C-1, using 20mm graded aggregate as in Plinth protection etc surface finished even and smooth without using extra cement and providing necessary joints 12mm wide to the full depth of PCC at every 3 meters and every change of directions and the joints duly filled with mastic filling comprising of 01 Part of heated bitumen blown grade any penetration and 3 parts of sand [all by weight] complete all as specified and as directed. 22 Material and labour for PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in surface channel and like etccompleteall as specified and as directed. 23 Materials and labour for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc.completeall as specified and as directed. 24 Add or deduct for each 25 mm girth or part thereof over or under 30cm from item No. 23 above. (For adjustment only) 25 Demolition of reinforced cement concreteof any description and in any position not otherwise specifically provided for complete all as specified and as directed. 26 Material and labourfor reinforced cement concrete (1:2:4) type B-1 using 20mm graded aggregate (nominal mix)for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves, chajjas complete all as specified and directed. 27 M & L for use and waste of form work to soffits of suspended slab such as roof slabs, floor slabs, landing and similar work, etc. not exceeding 200mm thick with rough finished surfaces of concrete flat complete all as specified and as directed. 28 Material and labour for mild steel TMT bars 10mm dia and over, cut to length bent to shape required, including cranking bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and as directed. 29 Material & Labour for Granite Stone Slabs of 20 mm thick as in Steps, Jambs, Pillars, Window Cills, Cooking Platform etc. and the like with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and jointed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of the Granite Slabsincluding backing coat of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed. 30 Demolition of brick work of any description and in any position built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed. 31 Material and labour forbrick work with sub class `B` bricks, old size,straight or curved on plan exc 6m mean radius built in cement mortar (1:4) complete all as specified and as directed. 32 Materials and labour for half brick thick brick work with sub class B bricks straight or curved on plan to any radius built in cement mortar(1:4) including 2 Nos of 6mm dia bars at every fourth course of brick work complete all as specified and as directed. 33 Taking down cement plaster on brick concrete surfaces including racking out joints hacking for key, scrubbing down with, water etc complete all as specified and directed. 34 Material and labour for 15mm thick rendering in CM (1:4) on concrete surfaces mixed with integral water proofing compound @ 200ml per bag of cement/ as per manufacturers instructions and finish the surface even and fair complete all as specified and directed.(Note:Water proofing compound shall be measured & paid separately) 35 Materials and labour for 10 mm thick rendering on other than fair faces of brick work or concrete surfacein cement mortar (1:6) andfinish the surface even and smooth without using extra cementcomplete all as specified and as directed. 36 Material and labour for 5 mm thick rendering in CM (1:3) on fair face of concrete surfaces as in ceiling etc finished the surface even and smooth without using extra cement complete all as specified and directed. 37 Material and labour for preparation of newly plastered wall surfaces and applyingAcrylic Smooth exterior paint of required shade ,two coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqmon wallsurfaces complete all as specified and as directed. 38 M & L for Complete removal of existing treatment of any description on wallsurfaces and applyingAcrylic Smooth exterior paint of required shade two coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqmon wallsurfaces complete all as specified and as directed. 39 Material and labour for preparing newly plastered Wallsurfacesandapplying two coats of Oil Bound Distemper over a coat ofprimer over 1 mm thick Cement based Wall Care Putty on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the Wall surfaces complete all as specified and as directed. 40 Material and labour for Complete removal of existing treatment of any description on wallsurfaces and applying 1mm thick Cement based Wall Care Putty on walls including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of Oil Bound Distemper over one of primer on wallsurfaces complete all as specified and as directed. 41 Material and labour for preparing newly plastered ceiling, chajjassurfaces and applying three coats of white washing complete all as specified and as directed. 42 Material and labour for preparation of old plastered or unplastered surfaces including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil and greasy spots and applying two coats of white wash on ceilings/chajja complete all as specified and as directed. 43 Material and labour for Writing letters or figures [Block, Roman, Italic or Indian] not exceeding 30 cm high with thick paint to stand out boldly and solidly without showing signs of brush marks complete all as specified and as directed. 44 Supply only liquid water proofing compound complete all as specified and directed. 45 Dismantling Wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed. 46 S & F False Ceiling Frame Work using Anodised Aluminium snap grid frame work of 600 X 600 mm panel size for false ceiling with Aluminium T section of size 38 X 25 X 1.50 mm thick for Main Runners, 25 X 25 X 1.5 mm thick for Cross Runners and Angle of size 25 X 25 X 1.50 mm thick along the Walls suspended with and including 6 mm dia, Galvanized mild steel wire as in suspenders of ceiling members fixed in proper positioncomplete all as specified and as directed. 47 Material and labour for 6mm thick prepainted Non asbestos fibre cement building boards (E-board), fixed on aluminium framework with screws complete all as specified and as directed. 48 Supply and fixing Rolled mild steel joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming to Fe 410-W (Gde-E- 250) quality- B etc complete all as specified and as directed . 49 Material and labour for preparation of new or previously untreated steel surfaces of any description over 10 cm width or girthand applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed. 50 Taking down Chowkats or frame with shutters [without taking off shutter from the frame] exceeding 1.5 Sq.m but not exceeding 4.00 Sq.m each and removing to store complete all as specified and as directed. 51 Supply and fixing 125x60mm size pressed steel, frames 1.6 mm thick for door with one or more rebates including necessary fixing lugs, hinges,lock strike plate, etc, complete all as specified and as directed. 52 Supply and fixing 105x60mm size pressed steel, frames 1.6mm thick for door with one or more rebates including necessary fixing lugs, hinges,lock strike plate, etc, complete all as specified and as directed. 53 Material and labour Plain cement concrete in bed block and filling of door frame type C-0 1:3:6 (10 mm graded stone aggregate) complete all as specified . 54 Supply and fixing for 35mm thick factory made flush door shutters solid core construction with block board core and ply wood face panels commercial type on both faces complete all as specified and as directed. 55 Supply & Fixing factory made, 35mm thick, Second Class Hard Wood, Glazed and Skeleton Shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part – I, Section 8, Clause 8.24 [a] and fitted to Chowkats complete all as specified and as directed. 56 Supply and fixing Second Class Hard Wood, plain, solid, straight Chowkats and Frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed. 57 Cutting holes into brick wall for inserting hold fast & making good dismantled portion in cm (1:3) or PCC (1:2:4) type B1, depth of cutting exe half brick but not exe one brick complete all as specified and as directed.Note: Cutting of holes will be carried out by using mechanical means like Groove cutter/ wall chaser. 58 Material and labour mild steel work as in holdfast and similar works conforming to Fe290 GDE E-165 complete all as specified and as directed. 59 Supply and fixing 25 mm thick exterior grade prelaminated particle board (prelaminated on one side) with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work for cupboard shutters complete all as specified. 60 Supply and fixing18/19 mm thick exterior grade prelaminated particle board (prelaminated on one side) with decorative choice lamination and other side balancing white lamination fixed with screws to timber frame work for Cupboard partition complete all as specified. 61 Material and labour for 6mm thick teak wood lipping with nails on block board or veneered particle boardcomplete all as specified and directed. 62 Material and labour well seasoned 2nd class hard wood plain fillets, square, rectangular in section, clean sawn secured with nails or brads, sectional area exc. 13 but not exc. 25 Sqcm complete all as specified and as directed. 63 Taking down chowkat with shutter without taking off shutter from the frame n.exc 1.50 Sqm each complete all as specified and as directed. 64 Supply and fixing Solid PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening complete all as specified and as directed. 65 Supply and fixing Factory Made Solid PVC Moulded Door Shutter, with Particle Board Core, 28 to 30mm thick [Stiles], with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm plain colour PVC sheet on back face, termite proof, water proof and fire resistant, supplying & fixing in frame at site as per specification & drawing shown on Serial Page No. 181 of MES Schedule Part - II complete all as specified and as directed. 66 Supply and fixing Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodisedof 100mm size, type B-21 complete all as specified and as directed. 67 Supply and fixing continious (Piano) hinges, mild steel, bright finish or electro galvanised of 30mm width (when open) complete all as specified and as directed. 68 Supply and fixing Mild Steel Door Spring 300 mm, Ordinary Rat Rail Rod Pattern springs including roller and roller plate complete all as specified and as directed. 69 Supply and fixing 150mm size extruded aluminium alloy handles, fabricated type anodized complete all as specified and directed. 70 Supply and fixing 125mm size extruded aluminium alloy handles, fabricated type anodized complete all as specified and directed. 71 Supply and fixing 150mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed. 72 Supply and fixing 200mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed. 73 Supply and fixing 100mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed. 74 Supply and fixing Aluminium alloy, anodised, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed. 75 Supply and fixing 40mm dia copboard knobs fixed with nut, screw and washer of brass polished. complete all as specified and as directed 76 Supply and fixing Hasp and Staple, safety type of aluminium anodised including bolt to hinge plate, fixed with screws of 100mm size complete all as specified and as directed. 77 Supply and fixing in repair Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised of 100mm size, type B-21 complete all as specified and as directed. 78 Supply and fixing in repair 200mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed. 79 Supply and fixing in repair 150mm size extruded aluminium alloy handles, fabricated type anodized complete all as specified and directed. 80 Supply and fixing in repair Aluminium alloy, anodised, sliding door bolt 250mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed. 81 Dismantling timber boarding of any description fixed in any position complete all as specified and directed. 82 Supply and fixing 2nd class Hard wood 20 mm thick boarding planed both side with butt joints fixed with nails in any situation complete all as specified and as directed 83 Material and labour forpreparation of new wooden surface exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primercomplete all as specified and as directed. 84 Material and labour forpreparation of old wooden surface exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. 85 Supply and fixing in repairs 25 mm dia Harrison Rails [Curtain Rails], mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified and as directed. 86 S & F Aluminium Powder Coated Three Track (2 glazed & one gauze shutter) Sliding Window Frame (aluminium sections weighing not less than 1.67kg/m for frame) and Shutters (aluminium sections weighing not less than 0.55kg/m for shutter) including necessary Joining Cleats, Glazing Clips, Neoprene Rubber Packing, Powder Coated Aluminium Snap Beading, Screws, Powder Coated Aluminium Fittings such as Locking Arrangement [4 Nos], including glazing with 5.5 mm thick Tinted Glass and aluminium Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium beading and making good the surface complete all as specified .Note: (a)The size of aluminium sections shall be all as specified in relevant IS code and MES Schedule Part - I.[b] Unit rate quoted shall be deemed to include for cost of rubber beading, glazing clips, neoprene packing, fittings such as locks, 5.5mm thick tinted glass and wire cloth etc. 87 Supply and fixing Powder coated aluminium louvered ventilators of size 600X600mm with glass louvers, without sash bars of aluminium sections weighing not less than 0.605kg/m for frame of size 40x20x2mm including necessary jointing cleats, glazingcleats, rubber packing , anodised aluminium snap beading,screws, anodised aluminium fittings and 5.5mm thick frosted tinted glass fixed in panels with suitable locking arrangementsand making good the surface complete all as specified . Note: (a)The size of aluminium sections shall be all as specified in relevant IS code and MES Schedule Part - I.[b] Unit rate quoted shall be deemed to include for cost of rubber beading, glazing clips, neoprene packing, fittings such as locks, 5.5mm thick tinted glass etc. 88 Supply and fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. 89 Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. 90 Supply and fixing mild steel work such as grills,gratings,guard bars etc and similar work conforming to Fe290 GDE E-165 complete all as specified and as directed. 91 Material and labour for preparation of steel surface n.exc 10cm width or girth and applying two coats of syntheticenamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed. 92 Demolition of Unreinforced Cement Concrete/ Lime concrete of sunken floor (ground or 1st) and removing rubbish to a distance exceeding 150M but not exceeding 250 M complete all as specified and as directed. 93 Material and labour forPCC 1:5:10 type E2, using 40 mm graded stone aggregate as in sunken floor complete all as specified and directed. 94 Material and labour for 20 mm thick cement plaster in CM 1:4 mixed with Water proofing Compound@ 200ml per bag of cement/ as per manufacturers instructions on sunken portion with acrylic based polymer modified cementitious composite compound as approved by GE/AGE(I) and applying cement slurry two layers i.e. 1st layer @ 0.488Kg/ Sqm mixed with composite compound @ 0.253 Kg/Sqm & 2nd layer @ 0.242Kg/ Sqm mixed with composite compound @ 0.126 Kg/Sqm and applying 200 micron polyfilm with adhesive complete all as specified and directed.Note: Minimum 4 hours gap for air curing will be maintained between 1st layer and 2nd layer. 95 Supply and fixing in repairs 10 litre capacity low level PVC flushing cistern (any colour), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete all as specified and as directed by Engineer-in-Charge. 96 Supply and fixing in repairs Vitreous China squatting pan of‘Orissa pattern’, size 580 mm x 440mm (white) with ‘P’ or ‘S’ trap, front or back inlet and foot rests, any pattern complete including provision of PCC bedding andconnection to trap, flushing pipe, antisyphonage pipe, etc. including making good the disturbed floor complete all as specified and as directed. 97 Supply and fixing in repairs vitreous china WHB of size 450x300mm including waste fittings, brass, chromium plated with long screwed shanks and flynuts, flange end bedded in red lead cement and other end fixed etc complete all as specified and directed. 98 Supply and fixing in repair low density polythene (LDPE) pipes of pressure rating 6 Kg/Sq cm bore of tube 32 mm for waste pipe of WHB or sinks etc complete all as specified directed. 99 Supply and fix in repair PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed. 100 Supply and fix in repair pillar taps 15mm dia bore fancy typewith capstain heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified directed. 101 Supply and fixing in repairs looking mirror ofsize 600mm x 450mm x 5mm thick bevelled edge of selected quality glass, decorative type mounted on 6mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers completeall as specified and as directed.. 102 Supply and fixing in repairs 15mm bore angular stop valve fancy type,chromium plated , screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed. 103 Supply and fixing in repairs Brass Chromium Plated Tubular Towel Rail, 20mm dia, D Type, 600 mm long between flanges complete all as specified and as directed. 104 Supply and fixing in repairs 15mm bore fancy type chromium plated bib taps with crutch of butterfly handle screwed down for iron pipes complete all as specified and directed. 105 Supply and fixing in repairs 15mm bore brass chromium plated mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all specified and directed. 106 Supply and fixing in repairs of size 125 mm brass chromium plated shower rose with or without swivel joints, any size including fixing to steel pipe or union complete all as specified 107 Supply and fixing in repairs Soap dish, vitreous China white of approximate size 160 x 160 x 90 mm complete all as specified and as directed. 108 Supply and fixing in repair 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified . 109 Supply and fixing in repairs 50mm bore high density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or innfloors etc complete all as specified . 110 Taking up or down 20mm bore steel water tubing & connections complete all as specified and as directed. 111 Taking up or down 15mm bore steel water tubing & connections complete all as specified and as directed. 112 S & FUPVC Pipe of 20 mm bore, of pressure rating 10 KGf / Sq.cm including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, sockets etc and fixed to walls, ceiling, and laid on floors including testing complete all as specified and as directed. 113 S & F UPVC Pipe of 15 mm bore, of pressure rating 10 KGf / Sq.cm including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, sockets etc and fixed to walls, ceiling, and laid on floors including testing complete all as specified and as directed. 114 Cutting chases, pinning in, making good to facings where required and pointing in CM(1:3) to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth in brick wall complete all as specified and as directed. Note: Cutting of walls will be carried out by using mechanical means like Groove cutter/ wall chaser. 115 Supply and fixing in repair stainless steel (conforming to AISI-304 grade) plate rack of overall size 31 x 36 x 10 or equivalent made of 0.6mm thick stainless steel sheetfixed on wall with 4 Nos, 50mm long screws & PVC rawl plug complete all as specified and as directed 116 Supply and fixing as in replacement stainless steel (conforming to AISI-304 grade) kitchen sink with drain board of overall size 915mm x 460mm and bowl size 410mm x 310mmx 160mm depth or equivalent made of 1mm thick stainless steel sheet with 40mm bore CP waste coupling, 32mm bore PVC waste pipe(heavy duty) 90 cm long,and bedded in cement mortar and fixed on CP cantilever brackets complete all as specified and as directed. 117 Dismantling water tank of capacity exc. 250 litre but n.exc. 500 litre and removing from site complete all as specified and as direcetd. 118 Supply and fixing500 ltrs capacity rotationalmoulded polythene three layer water storage tanks (Cylindrical vertical with closed top) hoisted & fixed in position complete all as specified directed. 119 Supply and fixing 20 mm bore Ball Valves, 20 mm Bore, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe [Minimum Weight 20mm - 210 Grams] etc. complete all as specified and as directed. 120 Supply & fixing in repairs gun metal gate valve 20mm dia with iron wheel head screwed both ends for iron pipe complete all as specified and directed. 121 Taking down PVC soil pipe with fittings from wall, treches of any description including fittings complete all as specified. 122 Supply and fixing 75 mm bore dia PVC (SWR) pipes single socketed, in any length with rubber ring loints, fixed to walls complete all as specified and directed. 123 Supply and fixing 110 mm bore dia PVC (SWR) pipes single socketed, in any length with rubber ring loints, fixed to walls complete all as specified and directed. 124 Supply and fixing 110 mm bore PVC (SWR) bends in any types complete all as specified and directed. 125 Supply and fixing 75 mm bore PVC (SWR) bends in any types with acess door complete all as specified and directed. 126 Supply and fixing 110 mm bore PVC (SWR) bends in any types with acess door complete all as specified and directed. 127 Supply and fixing 110 mm bore PVC [SWR] Branch Piece, Single [Single T] equal or unequal with access door including jointing with solvent cement complete all as specified and as directed. 128 Supply and fixing 110 mm bore PVC [SWR] Branch Piece, single [Single Y] equal or unequal with access door including jointing with solvent cement complete all as specified and as directed. 129 Supply and fixing 110 mm bore PVC (SWR) vent cowl complete all as specified and directed. 130 Material and labour for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment along external walls below concrete or masonry apron using chemical emulsion @ 2.25 litres per RM by drilling 12 mm dia holes up to 300 mm deep and 300 mm centre to centre including plugging holes complete all as specified and as directed. 131 Material and labour for Treatment of soil under existing floors using emulsion @ 01 litre / hole, 300mm apart including drilling minimum 300mm deep & plugging 12mm dia holes with CM(1:2) to match the existing floors complete all as specified and as directed. 132 Taking down carefullyexisting copper/Aluminum point wiring (light,socket or power) complete includingfittings such as switches, ceiling roses, pendents, sockets, boxes, light fitting etc and removing from site and making good disturbed surfaces of walls, floors etc complete all as specified and as directed. 133 Material and labour for point wiring , concealed on wall or ceiling for one light/fan/call bell point with 1.5 sqmmPVC insulated (FR-LSH) unsheathed copper cable multistranded conductor 1100 volts gradecontrolled by one way switchincluding 1.5 sqmm PVC (FR-LSH) insulated unsheathed copper cable multistrand conductor 1100 volts grade for earth continuitywire connected to common earth dolly drawn through and including PVC rigid conduit of adequate sizewith all accessories and the cables will terminate to Modular Type Pressed Metal Flush Box made out of 2.5mm thick MS Sheet of suitable size duly painted with black bitumen paint over a coat of red oxide primer and providing 3 mm thick plastic laminated bakelite sheet top cover for housing Switches, Sockets and Regulators etc. concealed in walls complete all as specified and as directed. Note: (i) Red coloured cable shall be used for live connection,black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board. (ii) Cutting chases will be carried out by using mechanical means like Groove cutter/ wall chaser.(iii) payment for cutting chases shall deemed to be included in the quote rate. 134 All as per item No 133 above but for 3 pin, 5 Amp Socket outlet on the same board complete all as specified and directed. 135 All as per item No 133 above but for 3 pin,5 Amp switch Socket outlet on independent board complete all as specified and directed. 136 All as per item No 133 above but for 3/5 pin,5 Amp switch Socket outlet on independent but below the switch board of light points in the same vertical plane wall complete all as specified and directed. 137 All as per item No 133 above but for one light point control by two way switch complete all as specified and directed. 138 All as per item no 133 here in before but for power point controlled by one 15 Amp switch on independent boardwith 2.50 sqmmPVC (FR-LSH) insulated un-sheathed copper conductor cable multistranded conductor 1100 volts grade and 2.50 Sqmm PVC (FR-LSH) copper conductor cable as earth continuity conductor. 139 Supply & fixing switch piano flush type (ISI marked), single pole, one way 5 Amp, 240 Volts complete all as specified & directed. 140 Supply and fixing switch piano bell push6 Amps, 230 volt flush type complete all as specified and as directed. 141 S & F Call bell, Ding dong AC, 230 Volts, Single Pole complete all as specified and as directed. 142 Supply & Fixing switch socket combination 2 in 1, 5 pin, 16 Amp flush type with all as specified and directed. 143 Supply & fixing Switch socket combination 2 in 1, 3 pin, 5 Amp flush type universal complete all as specified & as directed. 144 Supply and fixing socket out let, 2 in 1, 3 Pin, 6 Amps flush typecomplete all as specified and as directed. 145 Supply and fixing switch flush type 2 way6 Amps, 230 volt single pole complete all as specified and as directed. 146 Supply and fixing stepped type electronic fan regulator flush type complete all as specified and as directed.. 147 Supply and fixing ceiling rose, PVC/polycarbonate, isolated body surface bakelite, 65mm x 50mm,ISI marked three terminals complete all as specified & directed. 148 Supply and fixing as in replacement MCB DB SPN 8 ways double door, 230 Volts, powder painted including bus bar neutral link, earth bar and din rail,recessed with wall surfaces by chase cutting and making good surfaces of wall including taking down old unserviceable DB alongwith MCBs complete all as specified and as directed. 149 Supply and fixingMCB 6 - 32 Amps, SP, 230 Volt B series, breaking capacity 10 KA complete all as specified and as directed. 150 Supply and fixingMCB 6-32 Amps, SPN, 230 Volt B series, breaking capacity 10 KA complete all as specified and as directed. 151 Supply and fixingMCB 63 Amps, TPN, 415 Volt B series, breaking capacity 10 KA complete all as specified and as directed. 152 S & F in repairs MCB DB, TPN, 4 Way, 415 Volts, with DIN Channel, Double Door suitable with 200 Amps rated bus bar suitable for mounting MCBs flush mounted with wall including taking down of existing unserviceable DB with MCBs including making good disturbed surfaces complete all as specified and as directed.Note for ser Item No. 148 to 152: Make of MCB, MCCB DB and MCB DB shall be of same make as approved by AGE(I). 153 Supply and fixing in repairs LED street light fitting 35 Watt 230 V AC with Pressure Die Cast Aluminium Housing, IP66 protection, heat resistant glass cover, high power LEDs as light source, electronic driver, including GI Bracket made out of 32 mm bore GI Tube, Medium Grade of size not exceeding 1.50 m in length and bent to shape required and fixed with 2 Nos of Pole fitting Clamps made out of MS Flat of size 50 X 6mm, bolts, nuts, washers and painting with two coats of aluminium paint over a coat of primer red oxide zinc chrome primer and connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95 154 Supply and fixing in repairs Surface & wall mounted Energy efficient LED Tube Light Fitting, of 20 W, 6500 K of cool white, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm and making good the disturbed surfaces to match with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95 155 Supply and fixing in repairs Surface & wall mounted Energy efficientLED Mirror Tube Light Fitting, of 10 W, 2 feet long, 6500 K of cool white, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm and making good the disturbed surfaces to match with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95 156 Supply and fixing in repair Integrated LED Bulk head with luminaire of 10W, 6000 K with Pressure Die Cast Aluminium Housing, IP54 protection, heat resistant glass cover, high power LEDs as light source, electronic driver and connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. Note: Light fitting shall be of PF>0.95 157 Material & Labour for sub main wiringwith two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLS Copper conductor cable of size 4.0 sqmm (Nominal area) drawn through in and including PVCCasing/ Caping with all fittings and accessories alongwith one single core green colour PVC insulated unsheathed 1100 volt grade multi stranded FRLS Copper conductor cable of size 4.0 sqmm as earth lead and connected to earth dolly and including taking down old unserviceable sub main wiring of any description, making good to disturbed surfaces complete all as specified as directed. Note : (i) 3 Runs of 4.0 Sqmm cable and one run of PVC Casing/ Caping shall be measured as one unit length 158 Taking down ceiling fan carefully of any size from its original position, kept in safe custody and refixing the fan in same position or at new place including cleaning and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. 159 Taking down exhaust fan mounted fan carefully of any size from its original position, kept in safe custody and refixing the fan in same position or at new place including cleaning and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm complete all as specified and as directed. 160 Taking down carefully KWH meter with connection from its original position, kept in safe custody and refixing in same position or at new place including cleaning complete all as specified and as directed. 161 Supply and fixing in repair Decorative LED wall mounting, Champagne gold finish fixture with plastic body of9 W, Base type B-22 LED lamp complete all as specified and as directed. Note: Light fitting shall be of PF>0.95 162 Materials and labour for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised wire of 4mm diaby means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe of 15mm bore (light grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (medium grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar at 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on completion including taking down old unserviciable earthing set all as specified and as directed.Notes:-(i) Main earthing strip from earth plate electrode to rest point upto length of 7.5 meters length shall deemed to be included in the unit rate quoted against this item. (ii) On testing after completion if the desired resistenance is not obtained the contractor shall redo the earthing without any extra cost to the department.
