Tender For Development Of Sri Kailasanathar Temple, Thingalur In Thanjavur District.; 1 Earth work excavation for foundation in all classes of soils and sub soils and to depth as may be directed except in hard rock, requiring blasting, including infinal leads and lifts and re-filling the sides of foundation, with excavated earth in 150mm layers well watered rammed and consolidated, including depositing surplus earth within the compound in places shown with initial leads of 10m of 2m and lifts, clearing and levelling the site, shoring strutting baling of water wherever necessary etc., complete complying with standard specification. 2 Earth work OPEN excavation for foundation in all classes of soils and sub soils and to depth as may be directed except in hard rock, requiring blasting, including infinal leads and lifts and re-filling the sides of foundation, with excavated earth in 150mm layers well watered rammed and consolidated, including depositing surplus earth within the compound in places shown with initial leads of 10m of 2m and lifts, clearing and levelling the site, shoring strutting baling of water wherever necessary etc., complete complying with standard specification. 3 Supplying and filling in foundation with Crushed Stone Sand (M-Sand) including cost conveyance of all materials complete complying with standard specification complete 4 Cement concrete 1:5:10 (One cement five Sand and Ten aggregate) using 40mm gauge hard granite broken stone jelly for foundationincluding cost and conveyance of all materials labour formixing, laying, compacting, curing, dewatering, side shuttering, wherever necessary including curingetc.,complete complying with standard specification and as directed 5 Plain Cement Concrete 1:2:4 (one cement, two sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers. 6 Supplying and filling of Gravel by lorry in basement filling including conveyance loading and unloading charges and all other incidential charges filling laying watering and consolidation etc., complete as directed by the Dept., Officers with standard specification. 7 Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oakjoists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid) 8 For plane surfaces such asrcolumn footings, column pedestals, plinth beams, grade beams, staircase steps, etc. 9 For plane surfaces such asrectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc. 10 For plane surfaces such asrectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc. 11 Providing and laying in position, Standardised Concrete Mix M-25 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 350 kglms and maximum water cement ratio of 0.50, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials). 12 For Ground Floor 13 For First Floor 14 Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 400 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials). 15 Supplying and fabricating and placing in position M.S.grills for reinforcement for all RCC works, including cost of rods, straightening, bending, cracking tying grills,with 18 gauge galvanished binding wire and placing the grills in position etc., complete and as directed. 16 Brick work in CM 1:6 (One cement and Six M.Sand) using best quality country bricks of size 8 3/4 4 1/4x 2 1/4 for walls incluing cost and convetance of all labour andmaterials including scaffolding curing finishingetc., complete complying with standard specification and as directed.etc.,complete 17 For foundation & basement 18 In Ground floor 19 R.R Masonary in cement mortar1:5(one cement,and five crushed stone sand) for foundation and basement including simultaneously pointing above ground level with the same mortar directed by the departmental engineers etc., complete complying with standard specification. 20 Plastering with CM 1:5 (one cement and five sand) 12mm thick in all floors includingcuring etc., complete complying with standard specification and as directed by the departmental officers) 21 Special Celing plastering and finishing the exposed surface of RCC items of work such as slabs , beams, sunshades, faciam canopy slab, staircase waist slab, landing slab etc.,with CM1:3(One cement and Three Sand ) 10mm thick includinghacking the curface and providing cement mortar nosing, beading fpr sunshade, staircases, steps, landing slabs and finishing, curing, etc., in all floors complying with standard specification as directed by the departmental officers 22 Dadooing walls with best approved quality, white / colour glazed tiles of 300 x 200 x 6mmsize set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. 23 Flooring with Anti- Skid first quality design Ceramic Colouredtiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.Sand)base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. 24 Flooring with Anti- Skid first quality design Ceramic Colouredtiles of size 305 x 305 x 6 mm laid over 25 mm thick cement mortar 1:3 (One Cement and Three M.Sand)base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. 25 Cleaning the flooring areas surface from algae and dust using water and pointing wherever necessary with using NITO BOND (OR) SBR by FOSROC make with mixing of white cement,and if any damages in press tiles and replace new tile for same, using pressure grouting if any weakness points only. Applying of three coats of rain coats using NITO BOND AR (OR) SPR mixing of water @ ratio and applying one coat of primer two coat milk white colour polymer on the surface as well as fixing membrane in each and every wall floor joints followed by one extra coat of polymer (Green seal make ) including all labour, materials and completions. 26 Weathering Course Concrete using best quality broken brick jelly of size 20mm uniform gauge in pure slaked lime,the proportion of brick jelly to lime being 32 to 12.5 ( No sand is to be added ) by volume and laid over the R.C.C.roof slab in a single layer and consolidated to the finished thickness by beating the concrete with wooden beaters of approved pattern keeping the surface constantly wet by sprinkling lime jaggery water etc., complete. complying with standard specification. 27 Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stoneSand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 28 Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of U clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 29 Painting one Coat with White Cementfor plastering area complete. complying with Standard specification in all floors including all cost of materials brushes, scaffolding charges etc., complete complying with standard specification. 30 Painting Two Coats withWater Based Exterior Emulsion Paint including over priming coat in cement plastered wall surface in all floors including all cost of materials brushes, scaffolding charges etc., complete 31 Providing and fixing factory made single extruded 35mm thick WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction ofdepartmental officers. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 32 Paving the floor with best approved qualitygranite stoneSlabs of size 600 x 600 mm with not less than 20mm thick laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) and pointed with colour cement neatlyetc. The granite stone slabs and other materials to be used shall be got approved by the concerned Engineer before use on work, etc., complete as per standard speicification. 33 Supplying and paving the floor with Double charged Virtified Tiles of approved quality and brand (colour /Shade shall be got approved by the departmental officers concerned) of size 600mm x 600mm x 8mm in all floors over a base layer of cement mortar 1:3 (One cement and three sand) 20mm thick laid insitu true to alignment and pointed with white cement slurry mixed with colouring pigments at the rate of 0.40kg/sq.m and fixed in position without any air gap in between tht tiles complying with standard specification and as directed by departmental officers. 34 SSupplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia B class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works). 35 Supplying and laying of 83 mm thick high strength type of interlocking paver block by using Rubber Moulld designedconcrete mix 1:1:2 using 10 to 12 mm size HBG stone jelly, in required shapes and sizes having minimum compressive strength of 40 N/mm2 to be laid in flurrying bone pattern with approved non sticking surface at top. The rate is inclusive of leveling the site, providing sand cushion 100 mm thick, compacting with power compactor and sweeping the sand grouting and also inclusive of transportation charges loading, unloading and labour charges for laying the paver block etc., complete complying with standard specification and as directed by the departmental officers. 36 Supplying and laying of Interlocking Paver Block Stone 63mm thk. high strength type of interlocking paver block by using Rubber Moulld designedconcrete mix 1:1:2 using 10 to 12 mm size HBG stone jelly, in required shapes and sizes having minimum compressive strength of 40 N/mm2 to be laid in flurrying bone pattern with approved non sticking surface at top. The rate is inclusive of leveling the site, providing sand cushion 100 mm thick, compacting with power compactor and sweeping the sand grouting and also inclusive of transportation charges loading, unloading and labour charges for laying the paver block etc., complete complying with standard specification and as directed by the departmental officers. 37 Paving the floor with kota stone slab of size 600 x 600 of 18 / 20mm (un-polished) in all floors laid in of cement mortor 1:3 (one cement three sand), 20mm thick and pointed with colour cement neatly including polishing with polishing stone and oxalic acid etc., so as to perfectly smooth and glossy and including hire charges for polishing machine and power consumption charges etc. The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification. 38 Supplying and fixing mild steel iron grill for Windows Ventilators and grill gate etc., including one coat of red oxide primer using M.S. angle of size 40x40x6mm and grill using 20x6mm MS flat and necessary hold fast with M.S. angle of size of 40x40x6mm - 230mm long spliced at end is to be provided appropriate places for fixing the grill etc complete complying with standard specification. The type design for the grills should be got approved by the departmental officers before execution. 39 Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm P or S trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings..... 40 Supply and fixing in position of best Indian make white / colour glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers.(The urinal should be got approved by the Executive Engineer before use on works.) 41 Supplying, laying and jointing CPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using CPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications.The CPVC pipes shall be got approved by Executive Engineer before use on works. 42 35mm dia cpvc pipe 43 25mm dia cpvc pipe 44 20mm dia cpvc pipe 45 15mm dia cpvc pipe 46 Supplying and fixing in position best quality 75 mm PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications.(The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level 47 Supplying and fixing 25mm dia Gun Metal values ( Heavy Duty), GI fittings, pvc specials of various sizes of approved quality and ISI band as per standard specification. 48 Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works) 49 Supplying CPVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangementsnote :Since the labour for cutting, threading / pasting, sundries have already been included under pipe line item of works, no separate provision for fixing PVC specials needs to be allowed 50 32x20mm Reducer 51 32x20mmBrass FTA 52 32mm diaCoupling 53 40mm diaElbow 54 40mm diaTee 55 40mm diaCoupling 56 40mm diaUnion 57 40mm diaNipple 58 32mm dia value gate 59 Teak wood plug (50x50x100mm) 60 Supplying and fixing in position 15mm dia C.P.Brass screw down tap and pillar tap, longbody tap of approved make confirming to IS specifications and qulity including costof Shellac thread etc. complying with standard specification. 61 UPVC Ventilator :Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and Koints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work 62 Providing Pre construction Anti - Termite Treatment and creating a chemical barrier to the building by inKecting chemical emulsion of required concentration under grade slab, grade beam, alround the pile caps, Catch Basins, Trenches, Pits, Tunnels, Wall Trenches, Back fill, Plinth filling, Kunction of wall and floor, external perimeter of building, surrounding of pipes, expansion Koints, below U.G.Sump and retaining wall / side walls etc., as per instuction of chemical manufacture and as directed by the Department officer incharge. 63 Supply and installation of Greenlam Door (Essentia - serene - suede-1995) Overall size of 1535mm(W) x 1200mm(D) x 1995mm(H) and thickness of 12mm, Door of height 600x1785 with alumnium PC Door stopper channel, top rail, U Channel, Noise deafening tape. Complete Nylon adjustable foot, Coat hook, door knob,gravity hinge, nylon thumb turm indicator and Screws 64 Manufacturing, supplying and Fixing of stainless steel Hand rails for staircase using 50mm dia 304L Grade stainless steel pipe of 1.60mm thick at requied locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1.00mm thick as vertiscal at 900mm centre with 2Nos of 25mm dia intermediate horizontal stainless stell pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100x100x6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc., complete. 65 Labour charges for providing ornamental finishing to the Kodungai, including the Navadai Padmam detail at the bottom, projecting 1.2 m all around the building from the outer wall line of the roof slab and curving downward to 0.75 m below the bottom of the roof slab, as mentioned in the architectural detail drawing complying with as per directed. 66 Labour charges for providing ornamental finishing to the 0.4 m high parapet wall, all around the building above the Kodungai, with the Viyazhavari detail projecting 0.13 m from the 230 mm thick parapet along the outer wall line and extending 0.23 m in depth from the top, as per the architectural detail drawing complying with as per directed. 67 Labour charges for providing ornamental finishing to the wall below the plinth line, all around the building, with Kambu Ezhuthugam detail projecting 40 mm from the outer wall line and to a depth of 150 mm, as mentioned in the architectural detail drawing complying with as per directed. 68 Labour charges for providing ornamental finishing to RCC columns, visible in the elevation, up to 3.6 m in height and up to 0.30 m in width, with Padhavari on the Uvapeedam at the base, Stambam details on the shaft, and Pazhaga, Kundam, Thandam, Kadam, etc., details in the capital, as mentioned in the architectural detail drawing complying with as per directed. 69 Supplying and filling with aggregate including cost conveyance of all materials complete complying with standard specification complete. 70 40mm 71 20mm 72 Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of second class Table Mould Bricks of size 9 x 43/8 x 23/4 with Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification. 73 Providing and supplying heavy-duty steel luggage racks fabricated using 4 Nos of 7 ft (2.1 m) mild steel angles as vertical supports and 6 Nos of steel panels sized 36 (1 m) x 15 (375 mm) as shelving surfaces. The steel panels shall be fabricated from minimum 1.2 mm thick mild steel sheets, reinforced with bent edges for added strength and safety. The entire rack shall be assembled with necessary accessories including nuts, bolts, and corner brackets for structural stability. All components shall be finished with a corrosion-resistant powder coating in AD Grey for durability and a uniform appearance. The rack shall be designed to carry an approximate uniform load of 50–100 kg per shelf and shall be suitable for indoor use in luggage storage areas. 74 Providing and supplying CHAPPAL RACK constructed using 4 Nos of 7 ft (2.1 m) mild steel angles as vertical supports, fitted with 7 Nos of steel panels measuring 36 x 15 for shelving. The unit includes 18 Nos of 15 x 15 polypropylene (PP) plates to form individual slots for organized chappal/footwear storage. The rack shall be fully enclosed on three sides with mild steel cover sheets to prevent dust and maintain a clean appearance. All components shall be assembled with heavy-duty bolts and nuts, and finished with a rust-resistant powder coating in AD Grey for long-term durability. The chappal rack is suitable for high-footfall areas such as educational institutions, temples, offices, and dormitories. 75 24 Hours Programmable Timer Switch with Shortest Switching Time 15 Minutes 76 Supply and installation of Street light feeder pillar with 63A MCB incomer and 8 Nos 16A DP MCB with sheet metal enclosure - Weather proof type with inbuilt timer control All compontents covered with Hylem sheet of 12mm thickness with necessary bolts and nuts and with earth connection complete 77 Supply and laying of 4c x 6 sq.mm PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good 78 Supply and run of 4 of 4 sq.mm. (56 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour 79 Earthing as per the ISI specification with an earth electrode of 2.10 metre Class B GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonr 80 Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated single core unsheathed copper conductor of 1100V grade in suitable gauge MS conduit pipe on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour 81 SUPPLY OF NERI ARCHITECTURAL POST TOP STYLE LED LIGHT FIXTURE - MODEL - NERI- LIGHT 851-(40W-45W) Power Module LED, 3000K, 6000 Lumens Minimum, Upright - Light 851:its upper square frame in single piece made of die cast aluminum with a decorative element with threaded tube male G 3/4which is also made of die cast aluminum using pressure die-casting process, fixed on the top. Auxiliary and optical compartment can be accessed by tilting the top frame.Bottom frame in single piece, made of die cast aluminumwith a four-armed bracket & decorative element, which is also made of die cast aluminum. Screen made of polymethylmethacrylate(PMMA) molded in a single piece. Screens Impact resistance: IK06. Pure polyester powder coating in Metallic Grey Colour. Pure polyester powder coating in Standard NERI Grey Colour. IP Rating - IP 66. Height – 605mm, Length - 325mm, Width - 325mm,Weight - 6Kg, Area Exposed to Wind(S) - 0.16 m2 Power LED Module with Company /brand name printed on PCB with the metal core plate.LED Chips of CREE/NICHIA/OSRAM/LUMILEDS make - same should be supported by LED manufacturers tech sheet . Colour Rendering Index: Ra > 70.Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage& Over- Current, with in-built surge protection (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA/PC . LED Lifetime >1,00,000hours. Safety test report as per IEC 60598from UL/UL Authorised/Intertek lab should be submitted. BIS Certificate with manufacturer name same as brand proposed should be submitted. LM79 report also should be submitted fromUL/UL Authorised/Intertek Laboratory. Sample should be submitted for approval from concerned engineer-in charge. CAT REF - NERI ARCHITECTURAL POST TOP STYLE LED LIGHT FIXTURE - MODEL - LIGHT 851 (40W-45W) Power Module LED, 6000 Lumens Minimum / 3000K 82 SUPPLY OF 3M HEIGHT NERI ARCHITECTURAL POST TOP POLE (JM.04.24.007)-3M Height post top Pole Made of mild steel pipe section of 76mm dia. Decorative Base in Steel - Its design starting with dia 260mm for 170mm height, then tapers to 180mm, followed by a cylindrical section of 165mm dia., 365mm Height. It ends with a Top section consist of a Ring of 205mm dia. and 40mm height followed by a taperinng section with Bottom dia. 175mm, Top dia 105mm and Height of 90mm. Total Height of the Base is 700mm. A Steel base plate of 300mm x 300mm is welded at the bottom of the base. This base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation.Decorative cast iron flower starting with a dia 102 mm increasing gradually to 160mm and then tapering to a dia 99mm.Total height of cast iron flower is 304 mm & weight is 6.3kgs. Top Ring-(weight- 3kgs.) are made of cast iron. All cast iron parts weight mentioned are with +/- 5% tolerance. Entire pole including the decorative elements shall be made to provide pleasing aesthetics as approved by Architect/ Engineer in-charge.. The pole should be provided with an inbuilt junction box with 1No. 32A Heavy Duty Stud type connector and 1No. 6A SP MCB, at the bottom- the inbuilt box should have a flush door of suitable size. Wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole strength. Pole is treated with effective corrosion resistance methods & Cast iron parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint. Sample should be submitted for approval from Architect/ engineer-in charge..CAT REF - NERI-ARCHITECTURAL 3M HEIGHT POST TOP POLE WITH ORNOMENTAL BASE & RING 83 SUPPLY OF NERI ARCHITECTURAL POST TOP STYLE LED LIGHT FIXTURE - MODEL - NERI- LIGHT 851-(50W-55W) Power Module LED, 3000K, 7500 Lumens Minimum, Suspended - Light 851:its upper square frame in single piece made of die cast aluminum with a decorative element with threaded tube male G 3/4which is also made of die cast aluminum using pressure die-casting process, fixed on the top. Auxiliary and optical compartment can be accessed by tilting the top frame.Bottom frame in single piece, made of die cast aluminumwith a four-armed bracket & decorative element, which is also made of die cast aluminum. Screen made of polymethylmethacrylate (PMMA) molded in a single piece. Screens Impact resistance: IK06. Pure polyester powder coating in Metallic Grey Colour. Pure polyester powder coating in Standard NERI Grey Colour. IP Rating - IP 66. Height – 650mm, Length - 325mm, Width - 325mm,Weight - 6Kg, Area Exposed to Wind(S) - 0.16 m2 Power LED Module with Company /brand name printed on PCB with the metal core plate.LED Chips of CREE/NICHIA/OSRAM/LUMILEDS make - same should be supported by LED manufacturers tech sheet . Colour Rendering Index: Ra > 70.Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage& Over- Current, with in-built surge protection (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA/PC . LED Lifetime >1,00,000hours. Safety test report as per IEC 60598from UL/UL Authorised/Intertek lab should be submitted. BIS Certificate with manufacturer name same as brand proposed should be submitted. LM79 report also should be submitted fromUL/UL Authorised/Intertek Laboratory. Sample should be submitted for approval from concerned engineer-in charge. CAT REF - NERI ARCHITECTURAL POST TOP STYLE LED LIGHT FIXTURE - MODEL - LIGHT 851 (50W-55W) Power Module LED, 3000K / 7500 Lumens Minimum Suspended Type 84 SUPPLY OF 6M HEIGHT NERI ARCHITECTURAL SINGLE ARM POLE (JM.04.24.007)-6M Height Single Arm Pole made in combination of decorative base,mild steel pipe section of 76mm dia & Top bracket. Topbracket which is made in combination of steel pipe sections 76mm dia.(vertical) & 33mm dia.(gradually bent ) to get 500mm horizonal arm length & pleasing aesthetics. Decorative Base in Steel - Its design starting with dia 260mm for 170mm height, then tapers to 180mm, followed by a cylindrical section of 165mm dia., 365mm Height. It ends with a Top section consist of a Ring of 205mm dia. and 40mm height followed by a taperinng section with Bottom dia. 175mm, Top dia 105mm and Height of 90mm. Total Height of the Base is 700mm. A Steel base plate of 300mm x 300mm is welded at the bottom of the base. This base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation.Decorative cast iron flower starting with a dia 102 mm increasing gradually to 160mm and then tapering to a dia 99mm.Total height of cast iron flower is 304 mm & weight is 6.3kgs. Decorative cast iron pole top starts from bottom with a ring section of dia. 67mm followed by a ring of dia. 75mm, radially incrases to 100mm dia. for a height 15mm,then radially reduces to 46mm for a height 20mm followed by a jack shaped section(45mm(W & 20mm(H), followed by a ring of dia. 60mm which is followedby a Conical section(bottom dia. 40mm & top dia.10mm,140mm(H) with sphere shape(30mm dia.) on top-total height of the pole top is 260mm & weight is 2.5 Kgs. All cast iron parts weight mentioned are with +/- 5% tolerance. Entire pole including the decorative elements shall be made to provide pleasing aesthetics as approved by Architect/ Engineer in-charge. The pole should be provided with an inbuilt junction box with 1No. 32A Heavy Duty Stud type connector and 1No. 6A SP MCB, at the bottom- the inbuilt box should have a flush door of suitable size. Wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole strength. Pole is treated with effective corrosion resistance methods & Cast iron parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint. Sample should be submitted for approval from Architect/ engineer-in-charge. CAT REF - NERI-ARCHITECTURAL 6M HEIGHT SINGLE ARM POLE WITH ORNOMENTAL BASE & RING 85 SUPPLY OF NERI ARCHITECTURAL POST TOP STYLE LED LIGHT FIXTURE - MODEL - NERI- LIGHT 851-(50W-55W) Power Module LED, 3000K, 7500 Lumens Minimum, Suspended - Light 851:its upper square frame in single piece made of die cast aluminum with a decorative element with threaded tube male G 3/4which is also made of die cast aluminum using pressure die-casting process, fixed on the top. Auxiliary and optical compartment can be accessed by tilting the top frame.Bottom frame in single piece, made of die cast aluminum with a four-armed bracket & decorative element, which is also made of die cast aluminum. Screen made of polymethylmethacrylate (PMMA) molded in a single piece. Screens Impact resistance: IK06. Pure polyester powder coating in Metallic Grey Colour. Pure polyester powder coating in Standard NERI Grey Colour. IP Rating - IP 66. Height – 650mm, Length - 325mm, Width - 325mm,Weight - 6Kg, Area Exposed to Wind(S) - 0.16 m2 Power LED Module with Company /brand name printed on PCB with the metal core plate.LED Chips of CREE/NICHIA/OSRAM/LUMILEDS make - same should be supported by LED manufacturers tech sheet . Colour Rendering Index: Ra > 70.Electronic Power Supply for LED Module, which offers Protection against Short Circuit, Over- Voltage& Over- Current, with in-built surge protection (an additional surge protection device of 10kV also provided in-built the fixture). Optics with refractive lens in PMMA/PC . LED Lifetime >1,00,000hours. Safety test report as per IEC 60598from UL/UL Authorised/Intertek lab should be submitted. BIS Certificate with manufacturer name same as brand proposed should be submitted. LM79 report also should be submitted fromUL/UL Authorised/Intertek Laboratory. Sample should be submitted for approval from concerned engineer-in charge. CAT REF - NERI ARCHITECTURAL POST TOP STYLE LED LIGHT FIXTURE - MODEL - LIGHT 851 (50W-55W) Power Module LED, 3000K / 7500 Lumens Minimum Suspended Type 86 SUPPLY OF 6M HEIGHT NERI ARCHITECTURAL TWIN ARM POLE (JM.04.24.009)-6M HeightTwin Arm Pole made in combination of decorative base,mild steel pipe section of 76mm dia & Top bracket. Topbracket which is made in combination of steel pipe sections 76mm dia.(vertical) & 33mm dia.(gradually bent ) to get 500mm horizonal arm length & pleasing aesthetics. Decorative Base in Steel - Its design starting with dia 260mm for 170mm height, then tapers to 180mm, followed by a cylindrical section of 165mm dia., 365mm Height. It ends with a Top section consist of a Ring of 205mm dia. and 40mm height followed by a taperinng section with Bottom dia. 175mm, Top dia 105mm and Height of 90mm. Total Height of the Base is 700mm. A Steel base plate of 300mm x 300mm is welded at the bottom of the base. This base plate along with foundation bolts of suitable size to be used for ensuring firm grouting into the specially designed RCC foundation.Decorative cast iron flower starting with a dia 102 mm increasing gradually to 160mm and then tapering to a dia 99mm.Total height of cast iron flower is 304 mm & weight is 6.3kgs. Decorative cast iron pole top starts from bottom with a ring section of dia. 67mm followed by a ring of dia. 75mm, radially incrases to 100mm dia. for a height 15mm,then radially reduces to 46mm for a height 20mm followed by a jack shaped section(45mm(W & 20mm(H), followed by a ring of dia. 60mm which is followedby a Conical section(bottom dia. 40mm & top dia.10mm,140mm(H) with sphere shape(30mm dia.) on top-total height of the pole top is 260mm & weight is 2.5 Kgs. All cast iron parts weight mentioned are with +/- 5% tolerance. Entire pole including the decorative elements shall be made to provide pleasing aesthetics as approved by Architect/ Engineer in-charge. The pole should be provided with an inbuilt junction box with 1No. 32A Heavy Duty Stud type connector and 1No. 6A SP MCB, at the bottom- the inbuilt box should have a flush door of suitable size. Wind pressure calculation as per IS 875(part-3) & structural calculation report as per EN40 should be submitted to verify the pole strength. Pole is treated with effective corrosion resistance methods & Cast iron parts are painted in 3 layer coating(coating thickness-100 microns minimum) in which 1st layer with etch primer, 2nd layer with epoxy primer & 3rd final layer with PU paint. Sample should be submitted for approval from Architect/ engineer-in-charge. CAT REF - NERI-ARCHITECTURAL 6M HEIGHT TWIN ARM POLE WITH ORNOMENTAL BASE & RING 87 Supply and fixing of seating module; Size – 5 x 2 x2.5 foot,Castings – Made of casted material of 28 kg.,Strips –Made of FRP STRIPS,Nut Bolts – G.I Powder coated up to 90 Microns for directional signage. 88 Supply and fixing of seating module;Size – 5 x 3 foot,Castings – Made of casted material of 32 kg.,Strips – Made of FRP STRIPS 6 MM Thick.,Nut Bolts – G.I,Powder coated up to 90 Microns for directional signage. 89 Supply and fixing of seating module; Size – 5 x 2 x2.5 foot,Castings – Made of casted material of 28 kg.,Strips –Made of FRP STRIPS,Nut Bolts – G.I Powder coated up to 90 Micron for seating. 90 Supply and fixing of seating module;Size – 5 x 3 foot,Castings – Made of casted material of 32 kg.,Strips – Made of FRP STRIPS 6 MM Thick.,Nut Bolts – G.I,Powder coated up to 90 Microns for seating. 91 Supply and fixing of drinking water RO Purifier plant120 Litres per hour of Dispense Rate.AQUAGUARD GREEN PURE CHILL 80 PSS ROUV Water Purifier (Ambient & Cold dispensing)RO+ UV+ Cu Zn 120 Litres storage PSS Purifier Customized technology cum enhance delivers safe Drinking water as per WHO Standards.3-Faucets Taps- COLD & NORMAL 92 Supply and fixing of DUSTBIN 3 in 1 (SS - 3021),Size - 35000,Material – Made of SS302 Grade,3 in 1 Dustbin,Capacity – 320 Ltrs 93 Supply and fixing ofDUSTBIN,Size – 3 feet,CAPACITY - 70 LTRS 94 Excavating pits of site 0.45m x 0.45m x 0.45m filling them with garden soil mixture of manure, red earth and river sand in the ratio of 2:2:1 respectively and adding soil enrichments - neem cake (0.40 Kg / Cum). Procuring and planting specified country plants (listed below) of minimum 1.50M height. supporting it with a sturdy stake put into the pit by the side of the saplings and tied to it. The spacing, location and other details as per the drawings and specifications. Rate to include for excavation, plant cost, transport. garden sioil mix, neemcake, installation, labour, disposing the surplus earth,etc.. 95 NEODYPSIS DECARYII 96 TRACHYCARPUSFORTUNEI 97 JUNIPERUS CHINENSIS 98 TERMINALIA ARJUNA 99 AZADIRACHTA INDICA (ARJUNA) 100 NEOLAMARCKIA CADAMBA (KADAMBA) 101 FICUS BENGHALENISIS (BANYAN) 102 MASNIFERA INDICA(MANGO) 103 BAMBUSA VULGARIS (BAMBOO) 104 HOPEA PARVIFLORA (OR) GOLDEN CYPRESS 105 FICUS RELIGIOSA (PEEPAL) 106 Procuring and planting specified Shurbs (listed below) of 0.9m to 1.2 M height, supporting it with a sturdy stake put into the pit by the side of the saplings and tied to it. The spacing, location and other details as per the drawings and specifications, supply laying, transportation & mixing of soil improvement nutrients including manure as required in all pits ,flooding with water, dressing including removal or rubbish & surplus earth if any with all leads & lifts, planting & stacking in full & final location including all locations specified, finally fine dressing, levelling etc. 107 FICUS BENJAMINA COMPACTA 108 FICUS BENJAMINA STARLIGHT 109 PLEOMELE REFLEXA 110 PITTOSPORUM TOBIRA (OR) SPANISH CHERRY 111 ACALYPHA WILKESIANA JAVA 112 ACALYPHA WILKESIANA MACROPHYLLA 113 JADE VINE RED (OR) MAGNOLIA.CHAMPACA 114 JASMINUM GRANDIFLORUM 115 Supply and laying of springler and trip irrigation approved make and quality for Texmo single phase 2hp motor,2.5 sub cable,1.5 sub motor pipe, 2 pvc pipe 4kg,50mm pvc pipe 10kg,1/2Popup adjustment sprinkler set of 360° x 30°, 2 valve.1.5x0.5 Tee,2 elbow,2 tee, 1/2 inch elbow,1/2 tee,1/2 fla,1.5 flush valve,2 filter & assembly set, drip irrigation automation controller, Surge decoder protector, wiring panel box,2 smart irrigation valve,Air valve,2 Pressure releaser valveand fitting and accessories including laying earth work excavation and refilling after laying in necessary places etc., complete.The rate is including Materials and labour etc., complete as directed by the corporation officers 116 Texmo Single phase 2hp motor 117 2.5 sub cable 118 1.5 inch sub motor pipe 119 FITTING AND ACCESSORIES 120 Pump Fitting labour 121 50 mm pvc pipe 4kg 122 40mm inch pvc pipe 4kg 123 1/2 inch popup springler 124 50 mm valve 125 11/2*1/2 TEE 126 50mm elbow 127 50 mmtee 128 1/2inch elbow 129 1/2 inch tee 130 1/2inch fta 131 40mm flush valve 132 50 mm filter and assemblying set 133 Plumbing labour charge 134 Trinch open and closing labour 135 SMART DRIP IRRIGATION AUTOMATION CONTROLLER (6 valve controller) 136 SURGE DECODER PROTECTOR WITH TRANSFORMER/440V 137 SAFETY WIRING PANEL BOX 138 2 inch smart irrigation valve 139 AIR VALVE REALLYSIR 140 2PRESSURE RELESER VALVE 141 0.5mm multi core cable 142 Automation labour 143 Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) ( 5 points / Coil) Lower End 144 Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End 145 Supply and fixing of20W 4’ LED Fitting complete on wall or ceiling with TW round blocks with PVC unsheathed Copper leads from terminals to the fitting. 146 supply and fixing of 1200mm (48) sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 300 mm down rod with fan clamp with side plates and cross arm of size 450mm (18) 147 Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire and making good of the concealed portion with suitable colour 148 supply and fixing of 18W LED square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. 149 Supply and fixing of 300mm (12) sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall 150 Supply and fixing of louvers shutters arrangements for 300mm (12) sweep (light duty) AC exhaust fan 151 Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch on suitable module surface mounting Box (GI ) with module cover plate (plastic) on wall with connections. Higher End 152 Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 40A DP MCB Isolator as incoming and 6 nos. 6A to 32A SP MCB as outgoing on suitable angle iron frame on wall with earth connection only. Lower End 153 Supply and fixing of DP sheet enclosure with 32A DP MCB in flush with wall with earth connection 154 Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion 155 Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour 156 Supply and run of 4 x 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V on 7 / 20 GI bearer wire for service connection mains 157 Supply and run of 4 x 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V on 7 / 20 GI bearer wire for service connection mains 158 Supply and run of 2 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V on 7 / 20 GI bearer wire for service connection mains 159 Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1 x 1/8 copper flat) on TW plank of size 375mm x 300mm x 19mm with supporting TW reepers of 1 thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1 No 40 Amp 30 MA Double Pole RCD / RCCB (Higher End) with suitable necessary connection 160 Earthing as per the ISI specification with an earth electrode of 2.10 metre Class B GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry 161 Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection 162 For obtaing 1 nos. three phase service connections from TNEB 163 Supply and fixing of 7W / 9W LED for BH point 164 Supply and fixing of 3 Nos. 5A (3 pin and 2 pin) combined flush type wall socket with control switches concealed in suitable TW box covered with hylem sheet in flush with wall with earth connection (for computer plug socket)
