Tender For Sealed Quotation For Rates For Proposed Restoration Upgradation Alteration And Addition Of Bombay Veterinary College Parel Campus Mumbai Rates For Estimation Purpose- 1 Fencing: Providing and erecting corrugated galvanized iron sheets of 0.63mm thick (24 B.W.G.) fencing and fixed 75 mm above Ground level on vertical M.S Angle of 40 x 40 x 6 mm size including excavating pits for foundation and embedded in C.C. block using PPC cement of 1:4:8 mix of size 450 x 450 x 670 mm. at 1.75 M. c/c with iron bar 16 mm dia. as hold fast including welding link with angle frame at 30 cm c/c with nuts and bolts and horizontal M.S. Angles at top and bottom of 25 x 25 x 5 mm size and vertical M.S. flat 35 x 5 mm and 25 x 5 mm horizontal including cross support of 40 x 40 x 6 mm. Angles both sides at every corner or bends embedded in concrete blocks of 1:4:8 of size 450 x 450 x 670 mm etc. complete. 2 Providing and fixing 18 mm thk. scratch proof Engineered wooden flooring and skirting in deep walnut finish/teak finish as per sample approved by the architect and company specifications. Item to include providing and fixing skirting matching to the flooring as per company details and design including necessary bedding etc. complete. 3 Providing and fixing in position FOLDABLE Aluminium louvered window with anodised aluminium frame of approved make and of size 40mm x 20mm x 2.0mm (wt. 0.605kg/Rm) including adjustable aluminium frame, 4 to 6mm thk. Frosted glass, fixtures and fastenings etc, complete as directed by Engineer In Charge. 4 Design and supply and fixing fully fixed semi unitized structural glazing system includingwith SPIDER FITTINGS as specified: Glass panel shall be 13.5mm thick (6mm + 1.52mm + 6mm)glass unit. Outboard glass shall be 6mm thk heat strenghten. Glass shall be of approved colour and shade and having air gap with aluminium / SS Fin brackets for stabilizer with single joint and having 6mm thick toughened glass. The reflective coating shall be on surface no.2. The insulated glass unit shall be hermetically using primary sealant. The cost includes providing and applying masking at site. Price inclusive of all structural system. 5 Providing and fixing Exterior Grade fin Systems ofAluminium structured with cement bonded fiberboard or High pressure laminate panels (wood finish or any other material) by TDW FACE (VRLS Plain)inclusive of / with aluminium box section framework as per manufactures specifications) All inclusive as per Architects approval and manufacturers installation specification. Fin size to 450mm x 3600mm. (TDW FACE (VRLS PLAIN) 6 Providing and fixing C.P teak wood ceiling planks of 25 mm thk. as per existing detail, tongue and grooved including scaffolding if necessary and one coat of primer complete. Item to include all mouldings and chamfers to be made as per original design indicated by the Architects. Item to include using a larger section of wood to get the mouldings and chamfers as per original design, sample to be shown to the Architect for approval before fixing. 7 Design, Supply, fabrication & installation of suitable steel framework and accessories as required, the structural skylight which shall be cladded with 8mm clear toughened + 1.52 PVB lamination or advanced + 8mm toughened clear toughened, including all necessary fixtures, fittings as per the technical specifications. 8 Providing and carrying out metallizing the steel structure immediately after sandblasting the surface with approved zinc metal to a thickness of 200 DFT. This shall be done as per IRS Standards adopted by Railways RDSO. 9 Providing and fixing 975 wide, 0.71 mm trapazoidal Aluminium Sheets ( 2.41 kg/m2) out of Alloys ‐ AA 8011 and AA 3105 in approved colour including fixing accessories, overlapping the sheets as per specifications. Length of the sheets should be provided in single/maximum length possible as no joints occur long the width of laying. 10 VENEER PANELING: Providing & fixing 4 mm thk Veneer Panelling on 12 mm thk fire retardant plywood fixed on G.I. framework, complete, at all heights as per detail dwgs & as directed by Engineer. FRAME WORK-G.I framework fabricated with 80 x 26 x 0.5 ceiling sections@ 300mm c/c, with perimetre channel as required, 15 x 45 x 0.9 intermediate C channel @ 1220mm c/c, 25x10x0.55 ceiling angle securely fixed to structural sofit hangers @ 1220mm c/c, last ceiling angle not more than 610 mm from adjacent wall, connecting clips etc as required, complete as per manufacturerspecifications with 50mm thk 1000 GSM density polyester wadding placed between the framework. Frame shall be covered by 12 mm thk. comm ply with 4.5 mm thk. veneer as approved by Architect. 3 coats of melamine polish on veneer surface and complete with machine sanding, leveling, applying hard putty, filling gap etc. Including 50 mm thk, 1000 gsm density polyester wadding in between frame. Anti-termtite treatment to internal surface of frame & ply by Aldrex complete with scaffolding etc. NOTE: Pidilite Terminator Wood Preservative shall be applied on all wood, before fabrication. G.I frame work & will have 100x100 x12mm thk rigged rubber behind.Side wall panelling 11 Stage Area Flooring :Providingandfixing100X25mmthicksolidBTC wooden flooring of 100mm wide &1200mm long with toungue and groove, joints fixed on bottom salwood framework 75 X 75mm at 587mm c/c & top salwood framework 75 X 75mm at 600mm c/c with 60mm thick sand layer , and 19mm Marine Plyontheframwillbefixed,including spreading,levelling as per drawing, all trims, edges,skirting,asperdrawingetc.completeas directed. 12 Auditorium Area - Auditorium Chairs The proposed chair shall have a fully upholstered fixed back seat both using Moulded Polyurethane Foam of special grade & special quality & double weave upholstery material. The chair shall be free standing being fixed to the floor by three nos. anchor bolts in the base & coupled together by common armrests. Design shall be such, by choice of its size and section of the structural material used, that the stability of the row of seating, incorporating a number of chairs when coupled together as integrated row is fully ensured.The shell comprises of the following main components namely:1. The main frame proper.2.Seat and back proper.The seat 460X490mm with thickness of 130mm, shall comprise of the plywood support baseplate, the requisite Moulded P.U Foam 3’’ thick with ½ inch walling & requisite upholstery. The support plate shall comprise of 19mm good quality plywood hot moulded and cut to size, finished to be tight closed fit insertion into the cavity formed by the walling of the Moulded P.U Foam.Fabricate the back cushion to be 34mm P.U.foam of 17mm layer each with extra padding for lower back support. The back & seat will be fully & completely upholstered. The upholstery of both back and seat shall be stitched as wall slip-on covers & one edge of the rare for the back, and bottom one for the seat shall be kept open for slip-on purposes and then zipped ensuring a tight uniform wrinkle free finish all round. The machine stitching of the upholstery shall be done in lock stitch using double needle machine only. Each chair shall be supplied with Natural Oak Armrest approx. 10’’ long. Standard grain filling shall be done on the handles after which they will be polished in matt finish of approved tint. The Handles should be atleast 70mm wide.Each chair shall be numbered. Chair numbering to be anodised aluminium/ powder coated.Generally for all purposes of execution and supply the vendor shall duplicate the sample in all respects and where there are discrepancies betweenthe sample and specifications the vendor shall get it clarified and confirm in writing from the architects. The architects may make minor modifications. All metal components to receive electrostatically powder coating process including the nine tank Cleaning Covering Pickling, Degreasing, Activation, Phosphating, Passivation, etc. To ensure 100%grid adherence and minimal coating of 55 micras. This also includes powder coating of fitting material. In all respect the sample so submitted will supercede the specification.Supplying and fixing Auditorium chairswith wooden flat , wooden waterfall , PU flat , wooden flat etc.complete. Polyurethane foam - Apparent density - Seat 50 +-5kg/m3, Back 48+-5Kg/m3, ISO 845-1988IFD at 25%- Seat 15-18 kg/314 cm2, Back 11-14Kg/314 cm2, ISO 2349-1997IFD at 40%- Seat 21-24 kg/315 cm2, Back 17-20Kg/315 cm2, ISO 2349-1997Tensile strength - Seat >1.1mm kg/cm2, Back - >1mm kg/cm2, ISO 1798-1997Tear strength - Seat >0.5mm kg/cm2, Back >0.5mm kg/cm2 13 Dismantling RCC, Brickwork, Doors/windows, Steel trusses, plinths, Timber, existing plumbing fittings, pipes etc. from existing Buildings such as OLD Guest House building as directed and carefully stacking the salvaged items including labour, material, cranes, tools and plants, fuel etc. The work shall be carried out as per directions of Engineer in Charge carefully. Rate shall be inclusive of hiring of cranes and other machineries, tools and plants etc. required for dismantling. Note: Work shall be carried out with utmost care to avoid any damage to the existing property. The removal of Debris is to be part of this item and the site has to be cleared on a daily basis. The debris should not be dumped in landfills or illegally dumped and must be possibly reused on site or offsite for filling, levelling purposes. Contractor is advised to visit the site of work to assess the quantum of work involved as no additional item of dismantling shall be paid separately. Item to include shifting of usable furniture, dismantling roads, asphalt areas, removal of street lamps handed over to PWD, removal of all plumbing fixtures etc., and making the site bare and ready for excavation works. 14 Providing and fixing or replacing damaged teak wood with well seasoned B.T.C. wood for door or window frames or members of decorative frame of the same original design, size and pattern including all mouldings, rebating, holdfasts and any other necessary fittings and finishing with one coat of primer complete. 15 Providing and fixing 50mm thick flushed doubled leaved door using well-seasoned BTC wood inclusive of any brass inlay work. The rate for the door shall include adhesive and all the hardware like heavy duty Brass holdfasts, nails, screws, butt hinges, handles, lock, concealed door closer, door stopper etc. required to complete the item. All the exposed hardware shall be brass finish with a protective lacquer coat. Contractor to do complete finishing of the shutter inclusive of primer and paint or melamine polish as approved by the Architect. 16 Providing and fixing 10 Shutter Burma teak wood sliding folding FULL louvered doors/windows with T.W frame sliding and folding shutters of size 75mm x 40mm thick having BTC wood fully openable louvers as instructed by the Architect including all necessary fitting brass hardware like screws, nails, concealed hinges, tower bolts, handles and inclusive of track cost of the same design, size and weight, etc. complete. Item to also include making all the mouldings and design of the panels with all beading Patti as per size etc., Item to include complete finishing of the shutter inclusive of primer and paint/melamine polish as approved by the Architect. Mode of Measurement: Area of the door/window which is changed or made new in the entire door shall only be paid. The area of the shutter includes the entire opening with all the leaves. 17 Providing and fixing Burma teak wood shutter of size 75mm x 40 mm thick with well-seasoned BTC wood double leaves partly fixed/openable louvered shutters for doors as instructed by the Architect including all necessary fining brass hardware like screws, nails, hinges, tower bolts, handles of the same design, size and weight, etc. complete Item to also include making all the mouldings and design of the panels with all beading Patti as per size etc., Item to include complete finishing of the shutter inclusive of primer and paint/melamine polish with PU coating as approved by the Architect. Mode of Measurement: Area of the door/window which is changed or made new in the entire door shall only be paid. The area of the shutter includes the entire opening with all the leaves. 18 Providing and fixing 100-150mm high Individual cut SS letters chrome finish / Nickel plated brushed gold finish around 5-8mm thick of approved finish, to be glued to door lintels or any other area as indicated in the drawing or as directed by the Architect. Item to be inclusive of all fabrication and fixing with anchors, bolts, and hardware to fix on any surface. Item to be inclusive of sample for Architects approval. 19 Supplying and fixing - Single Bed of Craftsmill or equivalent make- Single bed of size 2m L X 0.96m D X 1.59m W, with height of bed 0.56m and 600mm high Head Board of design and type and size as approved by the Architect. as per shown in image. Bed frame work - Made of hardwood like Indian Teak or Seesham with polish of approved shade. Item to include under-storage with hydraulic system. All exposed surfaces to be finished with polish of approved shade. All interior surfaces of under-storage to be finished with laminate as approved by architect.Item to include spray coating all the surfaces with approved anti termite solutionincluding providing 10 year guarantee for the same as directed by the Architect or Engineer in Charge. Item to be approved by architect prior to procurement and installationItem rate validity:1 year. 20 Providing and fixing mattresses Seista Spring Mattress (Bonnel Spring) of size 78 x 42 x 8 of approved make and brand such as Hush Sleep Studio or any other equivalent brand. 21 Providing & laying 2.1 mm THK SBS modified self adhesive,cross laminated HDPE valeron lining waterproofing membrane, Dr. Fixit Samshield XL 2100, with the execution to be done by the manufacturers authorised/ trained / partner applicator with 10 years warranty against leakages, over the solvent based bituminous Torchshield primer @ 4 sqm/litre. This shall include Surface Preparation by cleaning work, i.e. smoothening the wooden surface of all the to even out all the rough edges the jutting fibres and kinds of impurities, moreover, the wooden surface should be dry and smooth as per manufacturers’ recommendation, all followed by termination of the membrane minimum 200mm above FL with aluminum termination bar shall be fixed with non corrosive fastener @ 4 One Number per RM, sealing of termination bar with PU Sealant / epoxy mortar / putty, as per manufacturer specification, etc. complete. The SBS membrane shall have Roll Size: 1 Mtr X 10 Mtr, Mass per Unit Area > 2.3 Kg/m2 as per ASTM D 5147, Puncture resistance > 200 N as per ASTM E 154, Elongation > 180% as per ASTM D 412‐06, Crack bridging (10 cycles) > 1.5mm as per ASTM C 836.Tensile Strength > 4 Mpa as per ASTM D 412‐06, Tear resistance > 20 N/mmas per ASTM D 4073, Softening Point (ᵒC) ≥ 105 as per IS 1205/1978, Low temperature Flexibility – 10 deg C as per ASTM D 5147, Chemical Resistance (pH) as per ASTM D 543, Hydrostatic pressure > 50M as per DIN 1048. 22 Providing and fixing well-seasoned Burma Teak wood ceiling planks of 25 mm thk. as per existing detail, tongue and grooved including scaffolding if necessary and one coat of primer complete. Item to include all mouldings and chamfers to be made as per original design indicated by the Architects. Item to include using a larger section of wood to get the mouldings and chamfers as per original design, sample to be shown to the Architect for approval before fixing. 23 Providing and fixing Introductory signage (S-E-01) Horizontal made up of 500 mm high (1 thick) individual cut Stainless steel letters SS 304 grade signage in two text layers one above the other and third layer made up of 200mm high stainless steel SS 304 cut letters (1 thk) as shown in the drawing, anchored into the ground or fixed in the wall. The letters to be anchored to each other using 5mm thk SS plate welded. All the three layered text to be anchored below ground 650mm deep cement concrete bed 1:2:4 (1 Cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) inclusive of excavation, centering, shuttering, curing and finishing using 20mm dia SS anchor rods and making sure of all necessary means/hardware required to anchor the signage to the ground/wall. (Total height of signage to add upto human scale/height). Including all the Taxes 24 Providing and fixing Introductory signage (S-E-03) of 1850 mm height and 75 mm in depth using 75mm x 75mm thk MS epoxy coated sections for the framework, cladded with precoated 4mm thk Aluminium sheets bent on the edges to give a seamless finish. Item to include printing on Aluminium as well as laser cutting for letters and other graphics as mentioned in as many colours as required. For the backlit portion of the signage, 5 mm acrylic sheet to be used and fitted with epoxy coated angle cleats as shown in the drawing The entire signage to be fitted to the ground using 6mm the MS epoxy coated base plate and anchored below ground upto depth of 750mm using cement concrete bed 1:2:4 (1 Cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) inclusive of excavation, centering, shuttering, curing and finishing using 20mm dia SS anchor rods and making sure of all necessary means to anchor the signage to the ground/ wall. The signage to also have panel doors at the back to maintenance inclusive of all hinges and locking mechanism. Including all the Taxes. 25 Fabrication and fixing of Cast Iron grill of approved design & drawing in cast iron of min 10mm gauge weight Not less than 40kgs/m2 & having pre cast base plate of thickness 10mm with provision of grouting for bolts. All cast iron members painted with anti-corrosion primer and coated with two coats of polyurethane coating and painted in glossy black colour as specified. All vertical upstands to be embedded in concrete block as shown in drawings. Bolts and nuts to be welded after fixing. Rate to be inclusive of base grouting providing, fixing nuts, bolts, welding, painting, etc. complete. 26 Providing and fixing 1800mm x 450mm x 500mm solid stone benches of solid Polished Steel Grey Granite stone as per the design given by the Architect, complete with drip moulds, Item to include, grooves as per design and having offset of 50mm on either side of bench at the base of malad stone with adequate bearing below ground for anchoring. The bench to also have logo etched on the seat by CNC cutting. item to include making a sample for approval, to 1:1 scale for the Architect. 27 MS Planter- Providing & laying in desired location MS planters of welded together with 2mm gauge sheets to be made, the bottom sheet to be made with perforated MS sheet to allow the passage (drain pipe) of excess water. The box to be interlockable and removable for maintenance purposes. Item to include fixing freestanding framework inside the planter at the bottom. Rate to include samples to be shown to Architect for approval.1.2x1.2mx0.45m
