|
| 1 | Providing and laying in position cement concrete ofspecified grade excluding the cost of centering andshuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand) : 3graded stone aggregate 20 mm nominalsize) as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 2 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:3 (1 cement :3 coarsesand) as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 3 | Providing Sal wood work in frames of doors, windows, clerestory windows and other frames, wroughtframed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 4 | Providing and fixing 30 mm thick shuttersKiln seasoned and chemically treated hollock woodpanelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 5 | Providing and fixing 5mm thick glasspanes (wieght not less than 10 kg per square meter) (Saint Gobin/Modi Guard) as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 6 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws as per direction of Engineer-In-Charge (Century/ Kit ply/Merino) as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 7 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size Kiln seasoned and chemically treated hollock wood as per direction of Engineer-In-Charge as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 8 | Providing and fixing 2nd class teak wood 50 x 20 mm wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete as per direction of Engineer-In-Charge as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 9 | Providing and fixing 12 mm dia chromium plated brass curtainrod having wall thickness of 1.25mm with two chromium plated brass brackets of approved make fixed with C.P. brassscrews and PVC sleeves etc., wherever necessarycomplete as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 10 | Providing and fixing 150x10 mm ISI marked oxidised M.S. tower bolt black finish (Heavy duty of approved make), (Barrel type) with necessary screws etc. complete as per direction of Engineer-In-Charge as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 11 | Providing and fixing 125 mmISI marked oxidised M.S. handles conforming to IS:4992(Heavy duty of approved make) with necessary screws etc. complete as per direction of Engineer-In-Charge as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 12 | Providing and fixing bright finished brass 100 mm mortice latch(Heavy duty of approved make) with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete as per direction of Engineer-In-Charge as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 13 | Providing and fixing bright finished brass hanging type floor door stopper(Heavy duty of approved make) with necessary screws, etc. complete as per direction of Engineer-In-Charge as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 14 | Providing and fixing on wall face unplasticised RigidPVC rain water pipes conforming to IS : 13592 Type A,including jointing with seal ring conforming to IS : 5382,leaving 10 mm gap for thermal expansion, (i) Singlesocketed pipes.110 mm diameter (Finolex, Supreme, Vectus make) as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 15 | Providing and fixing on wall face unplasticised- PVCmoulded fittings/ accessories for unplasticised RigidPVC rain water pipes conforming to IS : 13592 Type A,including jointing with seal ring conforming to IS : 5382,leaving 10 mm gap for thermal expansion 110 mm bend (Finolex, Supreme, Vectus make) as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 16 | 15 mm cement plaster on the rough side of single or halfbrick wall of mix : 1:4 (1 cement: 4 fine sand) as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 17 | Providing and applying white cement based putty ofaverage thickness 1 mm, of approved brand andmanufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 18 | Finishing walls with 100% Premium acrylic emulsionpaint having VOC less than 50 gm/litre and UVresistance as per IS 15489:2004, Alkali & fungalresistance, dirt resistance exterior paint of requiredshade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @1.43 litre/ 10 sqm. Over and includingpriming coat of exterior primer applied @0.90 litre/10 sqm as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 19 | Finishing with Deluxe Multi surface paint system forinteriorsand exteriors using Primer as permanufacturers specifications Painting wood work with Deluxe MultiSurface Paint of required shade. Two ormore coat applied @ 0.90 ltr/10 sqm over anunder coat of primer applied @0.75 ltr/10sqm of approved brand and manufactureas per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 20 | Painting Steel work with Deluxe MultiSurface Paint to give an even shade. Two ormore coat applied @ 0.90 ltr/ 10 sqm overan under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 21 | Repairs to plaster of thickness 12mm to 20mm inpatches of area 2.5 sq.meters and under, including cutting the patch in proper shape, rakingout jointsand preparing and plastering the surface of the walls complete, includingdisposal of rubbish to thedumping ground, all complete as per direction of Engineer-in ChargeWith cementmortar 1:4(1cement : 4 fine sand) including carriage of materials within all leads, lifts and heights. |
| 22 | Supplying and fixing 2nd class teak wood 20x6 mm fillets new wooden fillets wherever necessary as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 23 | Providing water proofing treatment of terrace i/c cleaning the surface , filling all visible cracks , applying Ist Coat using MAC/ INSTA coat with an acrilic modified coating as above as base and applying fibre coating as reinforcement 2nd and 3rd coating with MAC/ INSTA flex white Elastomeric coating as per IPH/HPPWD norms and specifications as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
| 24 | Dismantling old plaster work laid in mortar upto floor two levelincluding stacking of serviceablematerials and disposal ofun-serviceable materials within 20Metres lead (wooden/concrete joiststo be measured and paid for separately) as per the direction of Engineer-In-Chargeincluding carriage of materials within all leads, lifts and heights. |
