Tender For Providing And Installation Of Open Gym Equipments At Village Punjab Khore Under Dilli Gramodhya Abhiyaan (Dga)., rohini-Delhi

Providing And Installation Of Open Gym Equipments At Village Punjab Khore Under Dilli Gramodhya Abhiyaan (Dga).-Earth work in excavation by mechanical means (Hydraulic excavator) / in manual means in foundation trenches or drains (not exceeding 1.5 m width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. (A) All kinds of soil 2 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:5:10 (1 cement : 5 coarse sand (zone-III) : 10 graded stone aggregate 40 mm nominal size) 3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size). 4 Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. 5 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). 6 Providing and installationof AIR WALKER / HEALTH WALKER of size 1070x615x1509mm fabricated with main post of 114mm “C” Class G.I. pipe made of hot roller tubular steel and hot dipped galvanized and powder welded coated using Akzo Nobel of 60-80 micron thick. 7 Providing and installationof DOUBLE SIT-UP STATION with below specifications:- dimensions (lxwxh): 1500x1150x650mm, fabricated with main post of NB 50mm (G.I) ‘C’ class pipe of approved make. Main frame of NB 32mm (G.I) ‘C’ class pipe, leg support of NB 65mm (G.I) ‘C’ class pipe (‘NB’ stands for nominal bore i.e., internal diameter of pipe in millimeters) fixed on its top is back support made of perforated ms sheet of 2mm thickness. All pipes are powder coated using AKZO Nobel or equivalent point of 80-120micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. 8 Providing and installationof SURF BOARD/AIR SWING of size 1150 x 900 x 1250mm fabricated with main post of 114mm dia and “C” Class G.I. Pipe as per IS-1239 and rest of the pipe 40mm dia “C” Class G.I. Pipe as per IS-1239 and powder coated using Akzo Nobel or equivalent of 60-80 micron thick. 9 Providing and installationof HORSE RIDER STATION with below specifications:- dimensions: 1000x600x1100mm. Fabricated with main post of NB 100mm (G.I) ‘C’ class pipe of approved make. Main frame of NB 65mm (G.I) ‘C’ class pipe. Handle support frame of NB 50mm (G.I) ‘C’ class pipe. (‘NB’ stands for nominal bore i.e., internal diameter of pipe in millimeters). all pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. zinc primer paint is applied at all the welding points prior to finishing. base plate cover made of virgin LDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and colored. Foothold made of NB 25mm (G.I) ‘C’ class pipe. Seat to be made up from virgin LDPE plastic by rotational moulding with minimum 4.00mm thickness, colored, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. The equipment is fitted with inbuilt limiters to prevent unwanted movements. 10 Providing and installationof STAIR STEPPER in a combination of pair and a single step of size 1000 x 800 x 1400 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick “C” Class G.I. pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coasted using Akzo Nobel or equivalent of 80‐120 micron thick. 11 Providing and installationof LEG PRESS of size 2000x500x1600 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40 mm dia and 2.5mm thick “C” Class G.I. pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. 12 Providing and installationDOUBLE SHOULDER EXCISER/ PULL CHAIR of size 2572x805x2187mm fabricated with main post of 114mm and “C” Class G.I. Pipe made of hot roller tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 60-80mm micron thick. 13 Providing and installationof EXERCISING BAR/ PARALLEL BAR with below specifications: - providing designing and fixing of exercising bar in pair of size 1800x550x1700 mm fabricated with main post of 114 mm dia and 2.5 mm thick and rest of the pipe 40mm dia and 2.5mm thick. All pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handles bars are to be provided with high quality grip rubber at top end. Base plate cover to be made up from virgin LDPE manufactured by rotational moulding with minimum thickness of plastic as 8mm, colorful and uv resistant and environmental friendly. All open ends of pipe to be closed by G.I. / LDPE caps for user safety. 14 Providing and installationof CHEST PRESS/ SEATED CHEST PRESS (DOUBLE) of size 1957x733x2058mm fabricated with main post of 114mm “C” Class G.I. Pipe made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 60-80mm micron thick. 15 Providing and installation of SHOULDER TWIRL DOUBLE / ARM WHEEL of size 857x850x1815mm fabricated with main post of 114mm and “C” Class G.I. pipe made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 60-80mm micron thick. 16 Providing and installation of DUAL SKY WALKER/ DOUBLE CROSS WALKER of size 160-800 x 60-800 x 160-800 mm fabricated with main post of 114mm dia and “C” Class G.I. Pipe as per IS-1239 and rest of the pipe 40mm dia “C” Class G.I. Pipe as per IS-1239 and powder coated using Akzo Nobel or equivalent of 60-80 micron thick. 17 Providing and installation of HIP TWISTER TRIPLE/ WAIST TWISTER of size1840x1840x2000mm fabricated with main post of 114mm “C” Class G. I. Pipe made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 60-80mm micron thick. 18 Providing of KNEE BACK STRETCH/ LEG STRETCH of size 1200X550X900mm fabricated with main post of 114mm and 4.00mm thick “C” Class G.I. Pipe made of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel of 80-120mm micron thick, FRP / HDPE / LLDPE (Fibre Reinforced Plastic / High Density Poly Ethylene / Linear Low Density Poly Ethylene) seat with backrest is fixed over 40NB Galvanized bend pipe. 19 Providing and installation of CHIN UP STATION / HANGING STATION is made of 80mm dia GI “C“ class pipe with horizontal hanging support bar made out32mm dia G.I “C” class pipe with all necessary bench press exercising attachment , clear hight of chin up station is 2.0mtr and width 1.0 mtr. 20 Providing and installation of ROWING MACHINE with below specifications: - dimensions : 1280x800x1150mm. Fabricated with main post of nb 100mm (g.i) ‘c’ class pipe of approved make. main frame of nb 65mm (g.i) ‘c’ class pipe. Handle support frame of nb 25mm (G.I) ‘C’ class pipe. (‘NB’ stands for nominal bore i.e., internal diameter of pipe in millimeters). All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. zinc primer paint is applied at all the welding points prior to finishing. Base plate cover made of virgin LDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and colored. Foothold made of NB 65mm (G.I) ‘C’ class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, colored, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. the equipment are fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength m-25 and j shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. 21 Total Amount of DSR items (Item No. 1 to 5) 22 Total amount after applying GST correction factor @0.973 on A 23 Add Cost Index @3% on B 24 Total (B+C) 25 Total Amount of Non DSR items (Item No. 6 to 20) 26 Note: 1. The Rates of above items are inclusive of maintenance charges for 1 Year. No separate payment shall be made onaccount of maintenance for 1 year after completion of the work.2. 10% amount of gross work done shall be withheld in bills on account of 1 year Maintenance Charges in addition to 2.5% security amount deducted in each bill. The 10% amount shall be released after satisfactory completion of 1-year maintenance period. 27 Grand Total (D+E)

Refer document

INR 27629.0 /-

INR 13.81 Lakhs /-

FileName	File Description	File Size
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB
Click here to download tender document	Tender Documents	0 KB