|
| 1 | Excavating in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes, laying of cables, pipes etc not exc 10 Sqm on plan and getting out in any type of soil complete all as specified and directed. |
| 2 | All as per Item No 01 here in before but exc 1.5 m and upto 3.0 m depth. |
| 3 | Excavating over areas not exceeding 1.50 m deep and getting out in any type of soil complete all as specified and directed. |
| 4 | M&L cement concrete Type D2 1:4:8 (40mm graded aggregate) in foundation filling and mass concrete complete all as specified and directed. |
| 5 | M&L TMTbar 10mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) than 0.90mm dia complete all as specified and directed. |
| 6 | M&L TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders, cut to length bent to shape required, including crancking bending spirallyfor hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.9 mm dia or securing with clip quality complete all as specified and directed. |
| 7 | M&L for RCC (Nominal Mix) Type B1 (1:1.5:3) (20mm graded aggregate) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete etc complete all as specified and directed. |
| 8 | M&L for RCC (Nominal Mix) Type B1 1:1.5:3 (20mm graded aggregate) as in Columns, pillars, piers, posts and struts etc complete all as specified and directed. |
| 9 | M&L for Formwork for flat rough finished surfaces to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed. |
| 10 | M&L for Formwork for square rough finished surfaces to sides of Columns, pillars, posts, struts, piers and stanchions complete all as specified and directed. |
| 11 | M & L for Steel work as in tubular trusses as in post including special shaped washer and etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed. |
| 12 | Ditto all as per item no 11 above but in curved shape/sections for purlin and rafter members as per the site requirements. |
| 13 | S&F mild steel purpose made bolts of diameter of neck exc 12 mm but n.exc 20 mmwith hexagonal or square head one end and screwed the other or screwed both ends, each screwed ends to be fitted with washers and one hexagonal or square nut exc 30 cm long complete all as specified and directed. |
| 14 | S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachement conforming to Fe 410 W (Grade E-250, quality \"A\" ) complete all as specified and directed. |
| 15 | S&F for rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. and similar small articles conforming to Fe 410 W (Grade E-250 ,quality \"A\") complete all as specified and as directed. |
| 16 | M&L of 16mm thick Polycarbonate sheet (Clear, Bronze, Metallic grey, opal white/blue colours) fixing with 50mm wide aluminium top profile, rubber gasket and suitable size of SDST screws. The clamping shall have provision for rubber gasket for water sealing & silicon sealant shall be used for sealing intersection joints, if any. All the edges of sheets should be closed with suitable tape and aluminium angle complete all as specified and directed. |
| 17 | M&L for PCC 1:2:4 type B1 using 20mm graded aggregate as in surface channels and drains complete all as specified and directed. |
| 18 | M&L, Extra for forming fair finished drain or channel 50cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc., complete all as specified and directed. |
| 19 | M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying a coat of metal wall putty, sanding it smooth, followed by two coat of acrylic paint mechanically overmetal based primer to create a durable and rust resistant base complete all as specified and as directed. |
| 20 | M&L for Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft loose soil complete all as specified and directed. |
| 21 | Material and Labour for Hardcore of broken stones of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. |
| 22 | Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 23 | S&F for framed work such as grills, grating, etc with ends of bars shouldered and or riveted or forged into spikes, framed grating or similar work confirming to Fe 410-0 complete all as specified and directed. |
| 24 | M&L Precast RCC Type B1 1:2:4 (20 MM Gradedaggregate ) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces complete all as specified and directed. |
| 25 | M&L Factory made for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed. |
| 26 | M&L PCC 1:2:4, nominal mix, type B-0, using 12.5mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, coping, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified and directed. |
| 27 | M&L for prepartion of new concrete surface of any description over 10cm girth or width, not otherwise described applying two coats of synthatic enamel paint over a coat of primer complete all as specified and directed. |
| 28 | M & L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and directed. |
| 29 | M&L for rendering 10mm thick plaster in cement morter (1:4) on fair face of concrete brick masonary finishing the surface evenand smooth using extra cement complete all as specified and directed. |
| 30 | Returning filling in, including spreading, levelling watering and well ramming in layer not exc 25 cm thick complete all as specified and directed. |
| 31 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed. |
| 32 | M&L for applying two coats of road marking paint exc 10 cm wide in required shades or colour as per site requirementfor painting lines, dashes, arrows, letters, etc. on roads, pavements and the like complete all as specified and directed. |
| 33 | M&L for aluminium wind tie of any size fixed with self tapping screwswith integral EPDM washer in roof covering complete all as specified and directed. |
| 34 | Supply and laying of factory made Precast Perforated Lid having length of 500 mm, width suitable for placing on U - Shape storm water drain (PUSD) sizes 450 x 450 mm, thickness of 70 mm respectively. Lid should have T-6 load carrying capacity – 4.8 T Axle Load – 2.4 T Wheel Load, confirming to JIS & meeting IS requirements having High Performance Self Compacting Concrete of M-40-cylinder strength/ M-50 cube strength. The Fe 500/ Fe500D shall be used for reinforcement. The each lid unit should have slits of 155 mm X 20 mm slit on two sides along the width of the lid for storm water intake. Lid should have anti-skid finish at top (except 300 mm lid) . Each lid may have in-built, specially designed lifting inserts of appropriate load carrying capacity and fixed at specific location to avoid the tilting of the lid for safe & fast installation complete all as specified and directed. |
| 35 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 36 | M&L for applying two coats of synthetic enamelled paint over a coat of red oxide on steel or iron surfacebased materials of any description , not other wise described over 10 cm width or girth including preparation of new surfaces complete all as specified and directed. |
| 37 | S&FManually operated zebra blindsfor flexiblelight control and privacy having opaque strips aligned to block light with alternate horizontal strips of sheer and opaque fabric or polyester of size as per requirement width & drop, having hardware top tube made of extruded aluminium with spline adoptable to accommodate clutchmoulded plastic having self lubrication with glass fibre reinforcement having a minimum lifting capacity head adoptability operating chain plastic/steel ball chain adoptable to the clutch pitch for smooth operation of blinds locking member plastic /steel stop locks for limit setting adoptable to be steel chain bonding withwide double sided adhesive tape of reqd length for strong holding capacity spring booster provided as per the requirement bottom bar aluminium extruded circular section with powder coated finish ,for a perfect fall to fabric to avoid warpage /floating ends are covered with ends cap to give a perfect finish complete all as specified and as directed. |
| 38 | S&F Fully perforated 12mm thick micro regular edged or 10 mm thick square edged G.R.G. (Glassfibre Reinforced Gypsum) False ceiling tiles ofsize of 595mm x 595mm of approved texture, design and Pattenhaving moisture content less than 2%, humidity resistance of 99%,NRCO.50 to 0.75 as per IS 8225:1987, Non-combustible as per BS 476(part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter- locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main- T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L- shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm centre to centre and 40mm long dry wall wood screws. All accessories should be fixed as per manufacturer\"s instructions. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in- Charge |
| 39 | S&F 18 mm thick PVC Sheetprelaminated of approved texture as in cabinet with shelves and partitions including required beading and accessary auto close hinges, magnetic catch lock ,SS handle/ Profile complete all as specified and as directed by Engineer-in-Charge. |
| 40 | Supply fabricate & fix in position aluminium powder coated tinted(minimum thickness of powder coating 50 micron of approved colour) three track window ( two shutters glazed & one shutters wiregauge) with frame, glazed with 4 mm thick tinted glass and, wire gauge with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber bead joining cleat for fixing in position, concelled type lock for all three shutter, PVC roller etc all as specified below, including taking down old window complete all as specified and directed. (a) Frame (top & side) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 20831)(b) Frame (bottom) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 20832)(c) Top & side Members of shutter Section shall be be of size 18.00 x 40.00 x 1.55 mm (Section No 20738)(d) Shutter Interlock Section shall be be of size 18.00 x 40.00 x 1.45 mm (Section No 20737)(e) Bottom Members of shutter Section shall be be of size 18.00 x 40.00 x 1.55 mm (Section No 20736)Note:-Section No given above are of make Jindal, Contractor may use similar section of other make mention in Appx B |
| 41 | S/F for Gypsum board of false ceiling of12.5 thick Gypsum board of the suspension shall consit 6mm dia GI steel rod suspended from ceiling supporting aluminium grid of 38x25x1.5mm and cross tie of 25x25x1.5mm and aluminium angle 25x25x1.5mm including providing and fixing anchors for hanging the false ceiling from the slab making cutouts in the false ceiling for recessed light fittings AC duct grills etc and filling and finishing the joints including providing and fixingplaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire meshproviding and complete all as specified and as directed by Engineer-in-Charge |
