|
| 1 | Schedule \"A\" Section - I |
| 2 | Dismantling plain or corrugated mild steel sheeting any gauge, thickness, including Nanital or similar pattern roof covering, complete all as specified and directed. |
| 3 | Supply and fixing of Pre-painted galvalume aluminuim zinc coating GI based corrugated steel sheet 0.50mm thick, conforming to IS-15961 of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws, complete, all as specified and as directed.Note- The sheets shall have (150 gm/sqm total on both sides) with super durable polyester quality paint of approved colour, suitable for exterior application conforming to IS-15965. |
| 4 | Supply and fixing ofPre-painted galvalume aluminuim zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 MPa as in roof covering/cladding to wall, fixed with self tapping screws, complete, all as specified and as directed.Note- The sheets shall have (150 gm/sqm total on both sides) with super durable polyester quality paint of approved colour, suitable for exterior application conforming to IS-15965. |
| 5 | Supply andfixing of mild steel work as in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St-240 complete all as specified and as directed. |
| 6 | Supply andfixing mild steel, rolled sections as in main orcross beams, hip and jack rafters, purlin where connected to comman rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting platesconforming to grade Fe-410(Gde 250), complete all as specified and directed. |
| 7 | Taking down chowkats or frames area exceeding 1.50 Square meter andnot exceeding 4.00 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed. |
| 8 | Taking down chowkats or frames areanot exceeding 1.50 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed. |
| 9 | Suppling and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification complete all as specified and as directed. |
| 10 | Supply and fixing factory made pressed steel frames of size 105 x 60 mm for doors fabricated from 1.25 mm thick sheet, with one or more rebate including necessary fixing lugs, hinges, lock strike plate, etc. and one shop coat of priming including plain cement concrete 1:3:6 type C-0 (using 12.5 mm graded mechanically crushed stone aggregates)in filling of door frame complete ,all as specified and as directed. |
| 11 | Supply and fixing factory made solid PVC moulded door shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm thick plain colour PVC sheet on back face, fixing in frame at site as per specification & drawing complete all as specified and as directed .Note- Contractor shall submit to Engineer-in-Charge the Purchase vouchers before claiming payment. |
| 12 | Supplyand fixing factory made flush shutters35 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides, ISI marked, complete all as specified and as directed.Note- Contractor shall submit to Engineer-in-Charge the Purchase vouchers before claiming payment. |
| 13 | Supply and fixing double shutter steel window box type ERW hollow P section comprising of glazed/gauged skeleton shutterfabricated fromfollowing sections :-(a) ERW hollow P section frame of size 60 mm x25 mm made from 1.25 mm thick MS sheet (02 Nos i.e. 01 for glazed shutter and 01 for gauzed shutter ). Both P section shall be welded with flat iron 25x03 mm thick all around of frame on both inner and outer faces . (b) Style and rails of window shutters shall be fabricated with ERW hollow P section of size 50 mm x25 mm made from 1.00 mm thick MS sheet and comprising of 02 Nos sash bars for glazed window leafof T – section20 x 03 mm thick and one No sash bar of 20 mm x 3 mm thick section for gauzed winodw leaf .(c) Vertical mullion shall be ERW hollow T -section of size 60 x 25 mmmade from 1.25 mm thickMS sheet (d) The above steel window shall be deemed to include the following accessories/ fittings : i)Hold fast 150mm long mild steel flat iron 12x3 mm thick made to shape- 04 Nos per window ii)Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf.iii) MS tower bolt stove enamelled150mm long- 2 Nos per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 No per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 No per leaf . |
| 14 | item No. 12.00(contd....)vi)Pintal hinges 12 x 75 mm- 2 Nos each leaf vii) 10mm square Guard bar @ 10 cm c/c welded to frame .(viii) Fabrication and fixing arrangements as per specification including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and as directed by the Engineer-in-Charge.Notes :-(i) For the purpose of measurement and payment double shutter both glazed and gauzed with frames shall be considered as one unit.(ii) Unit rate quoted against this item shall also include the iron mongery, grill and other accessories as mentioned above.(iii) The window upto1.00 metre width shall consists of two leaves both for gauzed shutter and glazed shutter and all the shutters are openable.The window more than 1.00 metrewidth shall have two openable leaves onboth outer sidefor gauzed shutter and glazed shutter and middle leaf/shutter shall be fixed type.(iv) Contractor shall submit to Engineer-in-Charge the Purchase vouchers before claiming payment. |
| 15 | Supply andfixing galvanized steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staple and including fixing with beads supplied with joinery when fixed in panels of joinery, complete all as specified and as directed. |
| 16 | Supply andfixing for sheet glass 3mm thick, ordinary quality , in squarenot exceeding 0.5 Square metre each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified. |
| 17 | Material and labourfor prepration of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and as directed. |
| 18 | Material and labourfor prepration of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and as directed. |
| 19 | Material and labour for preparation of old wooden surface, of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paintcomplete all as specified and directed. |
| 20 | Dismantling of brick work or stone masonary, precast cement concrete wallingbuilt in cement mortar includingall quoins, arches, pillars etc., complete all as specified and directed. |
| 21 | Material andlabour for brick work with sub class ‘B’ bricks burnt, straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:6), complete all as specified and directed. |
| 22 | Material and Labour for Brick work with sub class ‘B’ bricks (Except Bricks), straight or curved on plan exceeding 6 metre mean radius, built in cement mortar (1:6) , complete all as specified.( Note- The serviceable bricks obtained from Serial item No- 18.00 will be used after removing motar, cleaning the bricks with water, etc.) |
| 23 | Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including racking out joints, hacking for key scrubbing down with water, etc.including removal the rubbish/ demolished material outside defence land, complete all as specified and directed. |
| 24 | Material and labour for rendering 15 mm thick on surface of any description of brick work or concrete wall surfaces in cement mortar 1:4 mixed with water proofing compound @ 2% by weight of cement or as per manufacturer\"s instruction and finished fair and even without using extra cement complete all as specified and as directed.( Note- Supply only integral WPC shall be measured and paid separately) |
| 25 | Supply only integral water proofing compound, complete all as specified and as directed . |
| 26 | Material and labour for Rendering 10mm thick on fair faces of newlybrick work or concrete surfaces in CM 1:6 finished even and smooth with out using extra cement(Internal surfaces) and taking down old plaster, complete all as specified and directed by Engr-In- Charge. |
| 27 | Material and labour forfor applying3 mm thick ( in two coats) wall careputty of new or undecorated plastered surfaces of wallcomplete all as specified and directed. |
| 28 | Material and labour preparatin of new / previously untreated surface walls by applying two coats of oil bound distemper (OBD) on wall surfaces over a coat of primer complete all as specified and directed . |
| 29 | Material and labour for preparation of plastered or unplastered old decorated surfaces of walls incl cornices, chajjas, sun shadesetc. and applying two coat of cement base paint (tint as approved by GE) complete all as specified and directed . |
| 30 | Material and labour for preparation of new plastered or unplastered surfaces of walls incl cornices, chajjas, sun shadesetc. and applying two coat of cement base paint, complete all as specified. |
| 31 | Material and labour for providing reinforced cement concrete 1:2:4 type B-1 (using 20mm graded mechanically crushed stone aggregate) in slabs supported on walls, beams and columns in floors, roof, landings, balconies, deck slabs and in shelves and the like with and including use and waste of necessary form work and Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of steel reinforcementas required to facilitate demolition and removal the rubbish/ demolished material outside defence landl complete all as specified. |
| 32 | Material andlabour TMT bars, 8 mm dia and over, cut to length, bent to shape required including cranking, binding spirally for hooping or column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm diaor securing with clips, complete all as specified and directed. |
| 33 | Material andlabour for premium quality, joint free, non skid, coloured ceramic 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm tiles, as in floor, set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the surface over and includingcement screed bed 15mm thick in cement mortar (1:4) base including dismantling of old unserviceable floor tiles, complete all as specified and directed. |
| 34 | Material and labour for premium quality, glazed coloured ceramic tiles 300 x 450 x 7mm thick on vertical surfaces of walls including 10mm thick rough finished plaster in cement mortar (1:3) set jointed in neat cement slurry and pointed in coloured cement to match andincluding dismantling of old unserviceable wall tiles, complete all as specified and directed. |
| 35 | Material and labour for machine cut kota stone slab 18-22 mm thick (of size not less than (55 cm x 55 cm) laid in glooring and jointed & pointed with grey cement slurry mixed with pigment to match shade of the slab including cutting waste, rubbing and polishing (Granite finish) over and including cement screed bed 20mm thick in cement mortar (1:4) base ,including dismantling of old unserviceable kota stone slab, complete all as specified and directed. |
| 36 | Supply and fixing stainless steelhinges, mediumweight cold rolled mild steel, size 100mm, ISI marked, complete all as specified and directed . |
| 37 | Supply andfixingaluminum anodized, barrel tower bolt of extruded section 150mm long, ISI marked, complete all as specified and directed. |
| 38 | Supply andfixing handle of extruded aluminum alloy, fabricated type, anodized 150mm long, complete all as specified and directed. |
| 39 | Supply andfixing300 mmaluminum anodised sliding door bolt, ISI marked, with hasp, staple (bolt type) complete with clamps bolt not less than 16mm dia and fixing clips of sheet, cast or extruded section and fixing bolts an sliding bolt of extruded section or cast aluminum alloy, complete all as specified and directed. |
| 40 | Supply andfixingFloor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, overall length of cover plate 140 mm, ISI marked complete all as specified and as directed. |
| 41 | Supply and fixing in repair, bib tap, long body, screwed down, high pressure, cast copper alloy, fancy type, chromium plated, ISI marked, with capstan heads, screwed down suitable for 15mm bore pipe or union complete all as specified and directed.Make- PRIMA Cat No PLF-6202 or equivalent model in makes mentioned in Appendix \"B\" of tender document.Note- Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment. |
| 42 | Supply and fixing in repair, angle cock, 15mm dia, cast copper alloy, chromium plated, ISI marked, screwed down, high pressure with capstain head, screwed both ends for iron pipes or for unions complete all as specified and as directed.Make-Prima Art No- PLF-6205 or equivalent model in makes mentioned in Appendix \"B\" of tender document .Note: Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment. |
| 43 | Supply and fixing of brass chromium plated tubular towel rail (finish Glossy), 20mm dia, D type, 60cm long between flanges complete all as specified and directed.Make- PRIMA Cat No PDX -4501 A or ESSCO Cat No-1111 or Prayag Cat No. BA-20 orequivalent model in makes mentioned in Appendix \"B\" of tender document.Note- Contractor shall submit a guarentee certificate for tubular towel rail from manufacturer to Engineer-in-Charge before claiming payment. |
| 44 | Supply and fixing in repair, PVC connections 750mm long with PTMT nuts and PVC washers on both ends fixed to 15 mm bore of pipe complete all as specified and directed. |
| 45 | Supply and fixing in repair, looking mirror of size 450mmx600mm and 5.5mm thick, selected quality, bevelled edges, glass mounted on 6mm thick AC building board with aluminiumbeadingandrubber packing and fixed to wall with wooden plug with chromium plated brass screws and cup washers complete all as specified anddirected. |
| 46 | Supplyand fixing in repaircoloured, vitreous China, box type, toilet paper holder fixed with chromium platedbrass screws, complete all as specified and directed . |
| 47 | Supply and fixing in repair, Grating square 125 mm size (openable) with waste hole of PTMT (Minimum weight 100gms) complete all as specified anddirected. |
| 48 | Supply and fixing in repair, Gun metal, globe or gates valves, with iron wheel head, screwed down, high pressure, heavy duty, ISI marked, screwed both ends for iron pipe or for union of 20 mm bore complete all as specied and directed.Make- Cat No PGT-1402 of PRIMA or equivalent model in makes mentioned in Appendix \"B\" of tender document. |
| 49 | Supply and fixing in repair, vitreous china coloured squatting pan of orissa pattern, size 580mmx440mm, white (Ist quality) with ‘P’ or ’S’ trap, with front or back inlet and integral foot rests of any pattern (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc including making good to existing floor surface and connection to flush pipe etc. complete all as specified and directed. |
| 50 | Supply and fixing in repair, vitreous china, wash hand basin, white, flat back, of size 550x440mm including painted CI brackets, embedded in wall in CM 1:4, with and including suitable size PVC waste pipe, PVC connections and chromium plated waste coupling, etc., complete all as specified and as directed. |
| 51 | Supply and fixing urinal spreader of PTMT any colour for fixing with 15mm dia pipe (Minimum weight 60gms) complete all as specified and as directed. |
| 52 | Supply and fixing in repair Vitreous China urinals, Half stall type (back or corner wall type) of size 420x395x635mm ofwhite with incl CP brass coupling, PVC flexible discharge pipe including chromium plated water spreader, connection pipe and discharge down pipe, complete all as specified and as directed. |
| 53 | Dismantling of water tanks exc 500 ltrs capacity but not exc 1000 ltr capicity and removal at site complete all as specified and as directed. |
| 54 | Supply and fixing in repair, water storage tank 1000 ltr capacity HDPE Triple layer, conforming to IS, fixed andhoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut , ISI marked, screwed andsuitable for iron pipe 20 mm bore, complete all as specified and as directed. |
| 55 | Supply and fixing in repair false ceiling tiles at all height with GRG (Glass fibre reinforced gypsum) false ceiling tiles with fully perforated 12mm thick micro tegular edged or 10mm thick square edged GRG false ceiling tile595mmx595mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRCO.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 476 (part 4) - 1970 and light reflctance of 85% minimum to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanised @120grams per Sqm incl both sides) comprising of main T-runners of size 15x32mm of length 1200mm, and secondry intermediate cross T- of size 15x32mm of length 600mm to from grid moudle of size 600x600mm, suspended from ceiling using galvanised mild steel items (galvanizing @80 grams per sqm) ie 50mm long, 8mm outer diameter M*6 dash fasteners, 6mm dia fully threated hanger rod upto 1000mm length and L-shape level adjuster of size 85x25x2mm galvanised iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on periphery wall/partition with the help of plastic rawl plugs at 450mm center to center and 40mm long dry wall wood screwscomplete all as specified and directed.Note- Ceiling tiles and ceiling grid shall be of the same make. Contractor shall submit to Engineer-in-Charge the Purchase vouchers and MTC before claiming payment. |
| 56 | Taking up or down steel tubing and connections for 15mm dia including cleaning for refixing or removal to store complete all as specified and directed . |
| 57 | Taking up or down steel tubing and connections for 20mm dia including cleaning for refixing or removal to store complete all as specified and directed . |
| 58 | Supply and fixing of 15mm dia tubes, medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, fixed to walls and ceiling or laid in floors, including cutting existing steel tubing and screwing, if required for alterations and additions, complete all as specified and directed. |
| 59 | Supply and fixing of 20mm dia tubes, medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, fixed to walls and ceiling or laid in floors, including cutting existing steel tubing and screwing, if required for alterations and additions, complete all as specified and directed. |
| 60 | Supply and fixing in repair, bib tap, long body, screwed down, high pressure, cast copper alloy, fancy type, chromium plated, ISI marked, with capstan heads, screwed down suitable for 15mm bore pipe or union complete all as specified and directed.Make- PRIMA Cat No PLF-6202 or equivalent model in makes mentioned in Appendix \"B\" of tender document.Note- Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment. |
| 61 | Supplying and fixing 15mm bore pillar tap,chromium plated cast copper alloy with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ complete all as specified and as directed. (Make : ESSCO Cat No-DLX-507 or Prayag Cat No.8602 or equivalent model in makes mentioned in Appendix \"B\" of tender document )Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment. |
| 62 | Supply and fixing in repair, CP grating doom (openable type) 100mm dia with or without waste hole both.(minimum weight 25 gms) complete all as specified and directed. |
| 63 | Supply and fixing in repair, soap dish size 160x160x90mm, vitreous china white, fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 64 | Amount of credit of Rs. 75812.18 for retrived old material as mentioned in Schedule \"A\" section-II of tender document in pdf form, will be deducted offline while acceptence of tender. |
