Tender For Annual Repair Works Of Govt. Residential Building Engineering College Under P.W.D. Sub Division No. 3 Rewa; 1 Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deepand disposal of rubbish, lead upto50 m and liftupto1.5 m. 2 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. 3 Supplying and filling in plinth with crusher stone dust / coarse sand under floors including, watering, rammingconsolidating in layers not exceeding 20cm in depth and dressing complete 4 Making bore holes for providing dowel bars at designed depth in rock foundation by drilling 40 mm dia bore hole in rock including necessary bending hooking, in position and grouting with cement slurry etc. complete as per drawing and spectification. (Steel to be paid separately). 5 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : With 20mm nominal size graded stone aggregate. 4.1.1.3 M 15 – Grade concrete 6 With 40mm nominal size graded stone aggregate. 4.1.2.2 Nominal Mix -1 Cement : 3 sand : 6 graded stone aggregate (M 10) 7 Brick work with well brunt open bhatta, bricks, crushing strength not less than 25kg / cm2 and water absorpt ion notmore than 20% in superstructure above plinth level and up to floor two level i/c curingetc complete. 6.6.2 Cement Mortar 1:6 (1 cement : 6sand) 8 Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces ofshutter. 9.18.2 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. 9 Providing and fixing ISI marked stainless steel sliding door bolts with nuts and screws etc. complete: 9.65.1 300x16 mm 10 Providing and fixing ISI marked stainless steel tower bolt black finish, (Barrel type) with necessary screws etc. complete : 9.66.2 200x10 mm 11 Providing and fixing ISI marked stainless steel handles with necessary screws etc. complete : 9.69.1 125 mm 12 Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. Wire and 1.4 mm wide aperture with matching wood beading 13 Providing and fixing bolts including nuts and washers complete. 14 Providing and fixing M.S. rivets of sizes in position. 15 Welding by gas or electric plant including transportation of plant at site etc. complete. 16 Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.10.22.2Frame, ladder, railing In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. 17 Providing and laying digital print random design(PGVT)/(GVT) vitrified tiles in different sizes with water absorption less than 0.05% and conforming to IS:15622 of approved make in all colours& shades, 1st quality/ premium quality including grouting the joints with white cement and matching pigments etc. complete 18.82.1 For floor glossy/ rustic /stain/matt finished laid on 20mm thick cement mortar 1:4 (1 cement:4sand) 18.82.1.1 Size 600X600 mm thickness 9-10 mm 18 12 mm cement plaster of mix : 13.1.21:6 (1 cement : 6 sand) 19 15 mm cement plaster of mix : 13.2.21:6 (1 cement : 6 sand) 20 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 21 Removing dry or oil bound distemper,water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 22 White washing with lime to give an even shade : 14.26.1 Old work (two or more coats) 14.26.1 Old work (two or more coats) 23 Colour washing with lime to give an even shade : 14.62.2 Old work (two or more coats) 24 Finishing walls with Acrylic Smooth exterior paintof required shade :Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface). 25 Old work (One or more coat applied @ 0.90 ltr/10 sqm). 26 Renewing glass panes, with wooden fillets wherever necessary: 14.6.1 Float glass panes of thickness 4 mm 27 Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50metres lead : 14.1.1 With cement mortar 1:4 (1 cement : 4 sand) 28 Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete including disposal of rubbish to the dumping ground within 50 meters lead :Door chowkhats 29 Window chowkhats 30 Making the opening in brick masonry including dismantling in floor or walls by cutting masonry and making good the damages to walls, flooring and jambs complete to match existing surface i/c disposal of mulba/ rubbish as directed by Engineer-in-charge. 14.4.1 For door/ window/ clerestory window. 31 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 14.37.1 one or more coats on old work. 32 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : 17.2.1 W.C. pan with ISI marked white solid plastic seat and lid 33 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : 17.11.2 White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap. 34 Providing and fixing unplasticisedPVC moulded fittings/ accessories for unplasticised Rigid PVC soil and waste pipes conforming toIS: 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. 17.59.5 Bend 87.50 17.59.5.1 110 mm bend 35 Providing and fixing unplasticised Rigid PVC soil and waste pipes conforming to IS: 13592 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Single socketed pipes for working pressure of 4 kg/sqcm.17.58.2110 mm diameter (minimum wall thickness 3.2mm) 36 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. 18.6.1 Internal work - Exposed on wall 18.6.1.3 25 mm nominal outer dia .Pipes. 37 Concealed work including cutting chases and making good the walls etc.15 mm nominal outer dia .Pipes. 38 25 mm nominal outer dia .Pipes. 39 Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of required diaas per dirction of Engineer-in-Charge.Reducer For 18.10.2.328.58 mm x 15.88 mm outer dia pipe 40 Elbow 90° 18.10.3.1 For 15.88 mm outer dia pipe 41 Reducing Tee 18.10.6.2 For 28.58 mm x 15.88 mm outer dia pipe 42 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 18.12.1 With C.I. wheel of approved quality (screwed end) 18.12.1.1 25 mm nominal bore 43 Providing and fixing C.P. brass bib cock of approved quality conforming to IS: 8931, 15 mm nominal bore. 44 Providing and laying water proofing treatment in sunken portion of WCs,bathroom etc., by applying cement slurry mixed with waterproofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment andsealing of all joints, corners, junctions of pipes and masonry with polymer mixedslurry. 45 Providing and fixing white vitreous china pedestal type Anti germ Fluoro-Polymer Coated Water Closet with soft closing seat cover, and 7.2 litre Low level slim dual flushing, PP (Poly Propeline) made 80 mm thick concealed flushing cistern, flushing capacity 3 litre/6 litre, with all fittings and fixtures complete including cutting and making good the wall and floors wherever required. 25.2.2 Anti-germ Fluoro-Polymer Coated Water Closet European type W. C. pan size 350 x 480 x 390 mm with solid poly propelyne made soft closing seat cover (Premium Range) 46 Providing and fixing white vitreous china type Anti germ Fluoro-Polymer Coated Wash Basin with C.I. Brackets, 15 mm C. P. wall mountedpressmatic pillar cock auto closing system (decol technology),15mm quarter turn angular stop cock, 32 mm C.P. brass made waste coupling length 130mm and 32 mm C.P. Brass Made Bottle Trap size 200x300mm fittings and fixtures complete including Painting of fittings and cutting and making good the wall and floors wherever required. White Vetrious China 25.7.1Anti germ Fluoro-Polymer Coated Wash Basin Size 160x580x450 mm with basin mounted pressmatic pillar cock auto closing system (decol technology). (Premium Range) 47 Edging (bricks) Edging with bricks laid dry length wise, including required excavation, refilling, consolidating with hand packing and spreading surplus earth neatly within a lead of 50 m: 28.17.1 Common burnt clay modular bricks 48 Providing and fixing M. S. tree guard 50 cmsquare in plan, height 1.40 metre above ground level and 0.50 metre below ground level. The vertical members shall consist of four nos. of angle iron of size 25x25x5 mm 1.9 long, one at Each corner and 8 nos. flat iron of size 25x5 mm 1.4 long. The vertical members shall be welded to 4 nos. 25x6 mm M. S. flats placed horizontally around the vertical member of the cage. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered PWD/ any other approved name. The tree guard shall be fixed to the ground by making suitable holes and by embedding four corners leg in the ground, including refilling the earth, compaction etc. complete. The tree guard shall be painted with two coats of paintof approved brand and manufacture over a coat of primer, complete in all respect. 49 All SOR ItemShalle be Applicable ofSCHEDULE OF RATES (SOR) For In force from January 01st , 2024 BUILDING WORKS
