tender for Construction of Market Stall (4 Nos) at Mallirhat Bazar, Samsad No.- VIII, Mouza- Bara Natabari Under Gasanimari-II Gram Panchayat.Fund: 5TH. SFC Sl. No. Item Description 1 Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. (a) Depth of excavation not exceeding 1,500 mm. 2 Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) a) With earth obtained from excavation of foundation. 3 Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. 4 Cement concrete with 30 mm down graded shingles excluding shuttering.N.B. VarietyIn ground floor (a) 1:3:6 proportion 5 Supplying & Laying as per IRC-SP:063-2004 Paver unit of any shade of approved quility as per relevant IS code, laid in pattern as directed in pavement, footpath, driveway (paver block only), etc including necessary underlay complete in all respect with all labour and material(Border concrete if necessary to be paid separately). Note: Sub-grade CBR should not be less than 5(b) supplying and laying in the specific pattern of inter locking concrete block pavement (ICBP) with concrete block (with concrete grade as specified as per table1 of IS15658:2006) manufactured from BIS licensee manufacturar, with Specer nib ......strenth/breaking load as per annexture G of IS15658, on the prepared base course of specified CBR as per table 1 of IRC SP 63 (2018) or else as mentioned in design and drawing with a cushion of compacted bedding sand of 25-35 mm thick ( Guarding of the bedding sand as per clouse 6.5.1 of IRC SP 63 and filling up the gaps in between paver blocks with joint filling sand ( the grading of the joint filling sand will be as per clouse 6.5.2 of IRC SP 63 and completing the edges with cut blocks as per CI. No. 8.7 of IRC SP 63(2018) with proper confinement of bedding and joint filling sand, compaction, levelling and filling up the edge gap50 mmthick,colour Decorative 6 Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (f) 25 mm to 30 mm shuttering without staging in foundation 7 Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (f) 25 mm to 30 mm wooden shuttering as per dicision & direction 8 Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes.(b) River bazreeGround Floor 9 Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes. (b) River bazree1st Floor 10 Reinforcementfor reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust ( if necessary), cutting to requisite length, hooking and binding to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. (a) For works in foundation and upto roof of ground floorTATA/ SAIL/ RINL 11 Reinforcementfor reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust ( if necessary), cutting to requisite length, hooking and binding to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. (a) For works in foundation and upto roof of ground floorTATA/ SAIL/ RINL 12 Brick work with 1st class bricks in cement mortar (1:6)(a) In foundation and plinth 13 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. 14 Plaster (to wall, floor, ceiling etc.) with sand and cement morter including rounding off or chamfering corners as directed and raking out joints or roughening of concrete surfece, including throating, nosing and drip course wherer necessary (ground floor).a) With (4:1) cement concreteI) 15mm thick plaster. 15 Plaster (to wall, floor, ceiling etc.) with sand and cement morter including rounding off or chamfering corners as directed and raking out joints or roughening of concrete surfece, including throating, nosing and drip course wherer necessary (ground floor).a) With (4:1) cement concreteI) 10mm thick plaster. 16 Plaster (to wall, floor, ceiling etc.) with sand and cement morter including rounding off or chamfering corners as directed and raking out joints or roughening of concrete surfece, including throating, nosing and drip course wherer necessary (ground floor).a) With (6:1) cement concreteI) 20mm thick plaster. 17 Neat cement punning about 1.5mm thick in wall dado, window, sills, floor, drain etc. 18 Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. In ground floor.3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement). Using grey cement (iii) 35 mm. thick 19 (a)Supplying, fitting and fixing steel rolling shutter profile type with18B.G. of approved type steel latche section 75 mm wide,fitted withcoil wire spring to necessiatethe fitting of required Nos. of C.I.Pulleys on heavy type solid drawn seamless steel tube complete withlocking arrangements both inside and outside specially builtup sideguide channels including providing a hood for the steel rollingshutter in the room, painting two coats of approved aluminium paintover a coat of red lead primer complete. 20 Applying Interior gradeAcrylic Primer of approved quality and brandon plastered or cencrete surface old or new surface to receiveDistemper/ Acrylic emulsion paint including scraping and preparingthe surface throughly, complete as per manufacturers specificationandas per direction of the EIC. (In Ground Floor)One Coat 21 Applying Acrylic Emulsion Paint of Approved Make and Brand on walls and ceiling including sand papering in intermediate coats including putty Two CoatsSrandard Quality 22 Applying Exterior grade acrylic primer of approved quality and brand on plastered or concrete surface old or new surface to receive decorative textured ( matt finish) or smooth finish acrylic exterior emulsion paint including scraping and papering the surface throughly, complete as per manufacturers specification and as per direction of the EIC.Ground Floorone Coat 23 Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturers specification and as per direction of the EIC. To be applied over acrylic primer as required. The rate includes cost of material, labour. Scaffolding and all incidental charges but excluding the cost of primer. In Ground Floor (Two coats) b) Premium 100% acrylic Emulsiom 24 Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surface by sand papering etc. 25 Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary: a) On steel or other metal surface: with super gloss (High- gloss)Two Coats
