Tender For Nrs Medical College And Hospital Endocrinology Department Ordinary Repair And Painting Of Rooms Designated For The Tobacco Cessation Clinic At G F And Other Allied Work During 2025 2026 - NRS MEDICAL COLLEGE & HOSPITAL - ENDOCRINOLOGY DEPARTMENT- ORDINARY REPAIR & PAINTING OF ROOMS- DESIGNATED FOR THE TOBACCO CESSATION CLINIC AT G.F & OTHER ALLIED WORK DURING 2025-2026. Sl. No. Item Description 1 Dismantling chunar stoneflooring carefully including removing rubbishwith in a lead of 75 m. and stacking the serviceable materials as directed. 2 Dismantling all type of plain cementconcrete works, stacking serviceable materrials at site and removing rubbish as directed with in a lead of 75 m In ground floor including roof. 3 (a) upto 150 mm. thick. 4 (a) Applying 2 coats of bonding agent with synthetic multi functional rubberemulsion having adhesive and water proofing properties by mixing with waterin proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturersspecification [Cement to be supplied by the Department] 5 Cement concrete (1:1.5:3) with graded stone chips 5.6 mm size with hexagonal square mesh wire netting, I.R.C. fabric mesh or X.P. M. fitted and fixed after tying the existing reinforcement on concrete without distributing the same and with proper scarping and cleaning the reinforcement and disturbed concrete with wire brush etc. after applying a coat of cement including the cost of wire netting I.R.C or X. P. M. & cost of all handling and scaffolding complete as per direction of Engineer-in -charge. 6 a) 20 mm thick 7 Ordinary cement concrete(mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttring and reinforcement, if any, in ground floor as per relevant IS codes. 8 (a) Pakur Variety. 9 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. 10 Plaster ( to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering conrners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (ground floor). [Excluding cost of chipping over concrete surface]. 11 (i) with 1:6 cement mortar. 12 (b) 20 mm. thickplaster. 13 (ii) With 1:4 cement mortar . 14 (c)10 mm. thick plaster. 15 Supplying,Fitting & fixing 1st quality Ceramic tiles inwalls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. 16 (B) Wall With Sand Cement Mortar(1:3)15mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m. & joint filling using white cement slurry @0.20kg/Sq.m. 17 (a) Area of each tile upto 0.09Sq.m. 18 (i) Coloured decorative. 19 Supplying and laying true to line and level Double Charge Vitrified Tiles of approved brand conforming to IS 15622: 2006(Group B I a) and tested as per IS 13630:2006 (relevant parts)[Non-modular sizes for tiles with Water Absorption (av.) ≤0.08 %] in floor, skirting etc. set in 20 mm thick sand cement mortar (1:4) bed prepared after application of slurry using 1.75Kg of cement per Sqm over the base and 2mm thickc ement slurry using cement @2.91Kg./sqm at the back side ofthe tiles and laid over the mortar bed using 0.2 kg/sqm of White cement used for joint filling with approved pigment as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost ofmaterials, Iabour and all other incidental charges complete true to the manufacturers specification and direction of Engineer-in-Charge. (Note: This work should not be executed without specific permission of SuperintendingEngineer 20 (a) ln Ground FIoor:(size not Iess than 600mmX 600 mm X 9.5mm thick) 21 (a) M.S. orW.I. ornamental grill of approved design joints continuously welded with M.S., W.I. flats and bars for windows ,railing etc. fitted and fixed with necessary screws and lugs in ground floor.(Add extra @1% for each addl. floor up to 4th floor and @1.25% for each addl. floor above 4th floor). 22 (i) Grill weighing above 10 kg./sq.m.and up to 16kg/sq.m. 23 Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame excluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be corrected up to three decimals). 24 (d) Sal : Local. 25 Supplying solid flush type doors of commercial quality, the timber frame consisting of top and bottom rails and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 37.5mm wide battens places both ways in order to make the door of solid core and internal lipping with Garjan orsimilar wood veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing shutters in position but excluding the cost of hinges and other fittings in ground floor 26 (a) 35 mm thick shutters (single leaf) 27 Supplying fitting , fixing decorative lamination conforming to IS-2046 : 1995 as per approved make, brand , finish and thick ness with fitting, fixing the same on Particle / MDF / Ply Boards with recommended / approvedadhesive with proper clipping the sides for better attachment as per direction of Engineer-in-Charge. The rate includes the cost of labour, adhesive and all incidental charges thereof.in ground floor Glossy/Matt/Suede excluding surface texture of metallic lustre. 28 (i) Thick ness of laminate 1.5mm. 29 Iron butt hinges of approved qualityfitted and fixed with steel screws, with ISI mark. 30 (vii) 100 mm x 58 mm x 1.90 mm. 31 (i) Hydraulic door closer of approved quality as per I.S.I. standard fitted and fixed complete :. 32 (b) Medium (I.S.I. size 2). 33 Anodise aluminium barred/tower/socket bolt (full covered) of approved manufactured from extruded section conforming to I.S.204/74 fitted and Fixed with cadmium plated screws:. 34 (iv) 150 mm long x 10 mm dia. bolt. 35 Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S.230/72) fitted and fixed complete:. 36 (a) With continuousplate base (hexagonal/round rod). 37 (vi) 150 mm grip x 10mm dia rod. 38 supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar , end bifurcated with necessary screws etc. by cement concrete (1:2:4) as per direction . ( cost of concrete will be paid separately). 39 (a) 40mm x 6mm, 250mm Length . 40 Supplying,fitting & fixing of 2-Track / 3-Track Aluminium slidingWindow of all Aluminium sections viz. window frame (top,bottom & sideframe), shutter (top, bottom, side & interlock member) made of aluminiumalloy extrusions conforming to IS 733-1983 & IS 1285-1975, annodisedconforming to IS 1868-1983, fitted with all other accessories viz. PVCroller, EPDM gasket, maruti lock, screws etc. including labour chargesfor fitting & fixing of aluminium 2-track/3-track sliding window withfixing of glass (excluding cost of glass) all complete as per architecturaldrawings and direction of Engineer-in-charge.10-12 Micron thickness Annodizing filmNatural white 41 Supplying, fitting & fixing of Aluminium fixed partion wall of all aluminium sections viz top,bottom and side member, intermediate member , glazing clip made of Aluminium Alloy Extrusions conforming to IS: 733-1983and IS: 1285-1975, annodized conforming toIS:1868-1983, fitted with all other accessories viz. EPDM gusket,cleat, angle screws etc. including labour charges for fitting and fixing of aluminium fixed partition wall with glass / panel board all complete asper architectural drawings and direction of Engineer-in-charge.( Excluding cost of glass/ panel board,10-12 Micron thickness Annodizing film.Natural white. 42 a) for unsupported length of vertical member upto 1.50m. height of both ends of vertical member restrained but panel with in 0.90sqm 43 Supplying, fitting & fixing of partly glazed partly panelled or fully glazed single leaf Aluminium swing door of all aluminium sections viz door frame ( top and side frame), shutter ( top rail, bottom rail, lock rail,door vertical) , glazing clip made of Aluminium Alloy Extrusions conforming to IS:733-1983 and IS: 1285-1975, annodized conforming to IS:1868-1983, fitted with all other accessories viz. EPDM gusket,cleat,angle screws etc. including labour charges for fitting and fixing of aluminium door with door spring,/aluminium hinges, glass / Panel board all complete as per architectural drawings and direction of Engineer-incharge.( Excluding cost of glass/ panel board, door spring/ All hinges, door closer, door stoper,handle, tower bolt and locking arrangmentetc)10-12 Micron thickness Annodizing filmNatural white 44 Supplying fitting & fixing in position 9 mm thick Heavy Duty Cement board - Type-A (High Pressure steam cured, tested asper AS-1530 part 3 & BS-476 Part 4,5,6,7 & 8, density >1450kg/m3, Bond strength 15 N/sqmm fire resistant, termite proof, moisture resistant) reinforced with cellulose fibre manufactured through autoclaving process as per IS : 14862 &ISO 8336, with fibre cement screws in partition excluding cost of supporting structure as per drawings and direction of Engineer-in-Charge complete. (Note: The Item -26 under Section - U(Page - 247) can be used as supporting structure for internal partition ). 45 (b) Rendring the surface of walls and ceilingwith white cement based wall putty of approved make and brand (15mm thick). 46 Acrylic Distemper to interior wall, ceiling with a coat of solvent basedinterior grade acrylic primer (as per manufacturers specification)including cleaning and smoothning of surface.Two Coats 47 Supplying bubble free float glass of approved make and brand. Conforming to IS: 2835-1987. 48 (iv) 5 mm thick coloured / tinted / smoke glass. 49 Supplying, fitting and fixing PVC pipes of approved make ofof Schedule 80 (medium duty) conforming to ASTMD-1785 and threaded to match with GI Pi;es as per IS:1239 (Part-I) with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting piles, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required, jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accessories, specials. Payment for painting will be made seperately). 50 For Exposed Work PVC Pipes. 51 15 mm dia. 52 For Exposed Work PVC Pipes. 53 20 mm. 54 For Exposed Work PVC Pipes. 55 25 mm. 56 Supplying, fitting and fixing bib cock or stop cock. 57 PTMT (Polytetra Bib Cock / Stop Cock ( Prayag or equivalent)15 mm 58 Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. Specification with P.V.C. fittings complete, C.I. brackets including two coats of painting to bracket etc. 59 Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. Brackets on 75 mm X 75mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30mm dia, approved quality P.V.C.waste pipe with C.P. nut 32mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P.nut including mending good all damages and painting the brackets with two coats of approved paint. 60 550 mm x 400 mm size. 61 Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 . 62 Single socketed3 meter length. 63 110 mm. 64 Fittings. 65 Door Tee. 66 110 mm. 67 Fittings. 68 Bend 87.5o. 69 110 mm. 70 Double socketed - 0.60 m.length. 71 110 mm. 72 Labour for fitting and fixing U.P.V.C. pipes for above ground work including cost of jointing materials etc. fitting and fixing all necessary specials, cutting pipes, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps (any foor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Enginer-in-charge) Payment will be made on centre line measurement of the total pipeline including specials.). 73 Above ground. 74 110 mm dia. 75 Supplying, fitting and fixing Anglo-Indian W.C. in white glazed vitreous china ware of approved makecomplete in position with necessary bolts, nuts etc. 76 With P trap (with vent). 77 Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws supplied, fitted and fixed complete. 78 Anglo-Indian . 79 Plastic (hallow type) white. 80 Supplying, fitting and fixing towel rail with two brackets. 81 C.P. over brass. 82 25 mm dia. and 600 mm long.
