Tender For Maintenance And Repair Works To Chief Engineer Quarters In Ward No. 29.; 1 Clearing Heavy Jungle (W-0001) PWD SOR Page No.27 2 Clean removal of Cement plaster from walls etc., complete complying with standard specification. 3 Ceiling Plastering with cement mortar 1:3 mix (one cement three P-sand), 10mm thick in all floors for RCC slabs, Beams, Sunshades including packing, providing cement mortar beading for sunshades, staircase steps, landing slabs etc., as directed by the departmental officers etc., complete complying with standard specifications. 4 Plastering with cement mortar 1:5 mix (one cement five P-sand), 12mm thick in all floors using clean screened M-Sand and including cost of curing for fifteen days from the completion of thework and surface should free from undulations and including the cost of preparing the surface for plastering and protecting from other damages till setting of mortar etc., complete complying with standard specification. 5 Painting two coats with ready mixed Plastic Emulsion paint (weather proof) of approved quality and colour over a priming coat, including thorough scraping, clean removal of dirt and including necessary plaster of paris, putty wherever required etc., complete as per standard specifications. 6 Painting two coats for old wood work surface using best quality synthetic enamel paint etc., complete complying with standard specification. 7 SUPPLY & INSTALLATION OF AIR-CONDITIONER WITH COPPER COIL (1.5 TR Split Type AC Unit - 3 Star Rated) SOR, Vol I, Page No. 208 (Code M-1986) 8 Supply and installation of 4 KVA capacity Automatic Voltage Stabilizer with time delay relay SOR, Vol I, Page No. 208 (Code M-1988) 9 Supply and laying of 5/8” and 3/8” copper pipe (Extra beyond 3 metres supplied with AC unit) SOR, Vol I, Page No. 208 (Code M-1990) 10 Supply and fixing of MS stand for fixing outdoor unit SOR, Vol I, Page No. 208 (Code M-1991) 11 Supplying, fabricating and fixing in position of Aluminium anodised natural colour matt finish Double leafs door (with frame) half glazed and half PLB board using extruded aluminium section for frame and shutter with necessary accessories such as PLB 12mm thick, 5.50mm thick plain sheet glass, Alu. L angles, Rubber beading, aluminium clips, best double action floor springs / door closer, handles, tower bolt, hinges, pivot and locks including labour and power consumption charges required for fabrication, if necessary chipping, dismantling, making necessary holes in RCC columns, beams or masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc., complete. The aluminium surface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868 / 1962 of anodic film thickness of not less than 15 microns for all sections. 12 Providing Fencing above compound wall using 2 ply and 4 pronged of 10 gauge Galvanised Barbed wire to 20cm equal spacing and 25 x 25 x 6mm L angle to 1.00m height with an equal interval including cost and conveyance of all materials to site, fixing of L angle in position with CC 1:2:4 bed block and fixing of barbed wire etc., complete complying with standard specification. 13 Painting two coats with approved Cement Paint over cement plastered wall surface, ceiling and other new surface including cleaning, preparing the surface and curing etc., complete as per standard specification. 14 Painting two coats for old iron work surface using best quality synthetic enamel paint etc., complete complying with standard specification. 15 Earthwork excavating for Sectioning and Levelling and depositing on bank with initial lead of 10m & initial lift of 2m in Sand, Silt or other Loose Soil, Wet Sand or Silt not under water, Light Black Cotton Soil, Sandy Loam and Ordinary Soil including excavated earth etc., complete complying with standard specification (SS20B). 16 Plain Cement concrete in 1:5:10 [one cement, five M-sand and ten course aggregate] using 40mm size Hard Broken/Machine crushed Granite Stone Jelly including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted etc., complete complying with standard specification. 17 Supplying and erecting centering including necessary supports for the plane surfaces such as Drainage & Culvert Retaining walls etc., using mild steel sheets of size 90cm x 60cm and BG 10 stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding supported by casurina props of 10cm to 13cm dia spaced at suitable intervals etc., complete complying with standard specification. 18 Plain Cement concrete 1:2:4 [one cement, two M-sand and four course aggregates] using 20mm size Hard Broken/Machine crushed Granite Stone Jelly including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted etc., complete complying with standard specification. 19 Supplying and filling in foundation and basement with filling M-Sand in layers of not more than 15cm thick well rammed, watered and compacted etc., complete complying with standard specification. 20 LED OUTDOOR FITTINGS (LIGHT EMITTING DIODE) HIGHER END 120W LED Street Light Fitting with LED (VOL 1 with Index (PWD-HD-WRD)) unique code ( M - 1293) 21 Play Material including with fabrication etc complete., 22 Standard Double Swing 60mm cross bar 10 ft long with bearing and hooks,60 mm pipe legs 10 ft long 4 nos, Stainless steel chain and 2 FRP seats (As per Lowest Quotation rate) 23 Double Seesaw with metal seats 60mm circular pies of 6.5 ft long seasaw with LLDPE seats and bearing arrangements ,60 mm pipe stand (As per Lowest Quotation rate) 24 Stainless steel Slide 304 grade Stailess slide 10 ft long reinforced with 35 x 35 x 6 mm angle and 42 mm handle, ladder made of 50 x 25 mm pipes with suitable support pipes and safety grills (As per Lowest Quotation rate)
