Tender For Comprehensive Maintenance (B/R Items) Of Otm Units Of Saraibari And Comprehensive Maintenance (B/R Items) Of Md Accn Of Saraibari At Jorhat Military Station Under Ge Jorhat; 1 Cutting chases in brick wall, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed cond 2 Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4.0 Sqm each, complete all as directed. 3 Taking down shutters of any description exc 1.0 sqm and not exc. 2.0 sqm each, complete all as directed. 4 Taking down shutters of any description not exc. 1.0 sqm each and refixing in same opening, complete all as directed. 5 Dismantling timber scantlings 40 sq. cm and over in section unframed, in any position, complete all as directed. 6 Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level), complete all as directed. 7 Demolition of reinforced cement concrete of roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work 8 Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as directed. 9 Dismantling structural steel work including doors, gates but excluding framed truss etc., complete all as directed. 10 Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as directed. 11 Material and labour for, plain cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in bed block/ holds fast blocks, coping etc, complete all as specified and directed. 12 Material and labour for, RCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed. 13 Material and labour for, brickwork with subclass ‘B’ bricks, old size, straight or curved on plan exc. 6m mean radius built in cement mortar (1:6), complete all as specified and directed. 14 Cutting chases in brick wall, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and directed. 15 Material and labour for, 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed. 16 Supply and fix for, 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); complete all as specified and directed. 17 Material and labour for, 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed. 18 Supply and fix for, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as per specification & drawing. 19 Supply and fix for, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as per specification & drawing. 20 Supply and fix for, 75mm size stainless steel butt hinges, medium weight, complete all as specified and directed. 21 Supply and fix for, 100mm size stainless steel butt hinges, medium weight, complete all as specified and directed. 22 Supply and fix for, aluminium anodised, barrel tower bolts of extruded section of size 150mm long, complete all as specified and directed. 23 Supply and fix for, aluminium anodised, barrel tower bolts of extruded section of size 200mm long, complete all as specified and directed. 24 Supply and fix for, aluminium handles, cast type, anodised 150mm size complete all as specified and directed. 25 Supply and fix in repair for, mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed. 26 Supply and fix for, 300mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate, complete all as specified and directed. 27 Supply and fix in repair for, Harrison rails, mild steel, chromium plated curtain rails 20mm dia with fixing brackets, stops, rollers etc.,complete all as specified and directed. 28 Supply and fix in repair for, Harrison rails, anodised aluminium alloy curtain rails 20mm dia with fixing brackets, stops, rollers etc, complete all as specified and directed. 29 Supply and fix for, 100mm size hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed. 30 Supply and fix in repair for, floor door stopper of aluminium alloy body and tongue, overall length of cover plate 140mm, anodised, with hard drawn steel spring, fixed in floor, complete all as specified and directed. 31 Supply and fix in repair for, brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed. 32 Supply and fix for, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. 33 Supply and fix in repair for, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. 34 Supply and fix in repair for, aluminium (extruded section) door closer hydraulically regulated, designation No.3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, complete all as specified and directed 35 Supply and fix for, mild steel flat iron 25 x 3mm as in band, straps, hold fasts etc. and similar small articles conforming to Fe-410-0 or Fe-310-0, complete all as specified and directed. Note: The hold fast shall be treated in two coats of tar and the cost for the same is deemed to be included in unit quoted rate. 36 Supply and fix for, rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe 410 - W (Gde - E- 250) quality-A, complete all as specified and directed. 37 Supply and fix for, mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed. 38 Supply and fix for, pressed steel frames 105 x 60mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed. 39 Supply and fix for, pressed steel frames 125 x 60mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed. 40 Supply and fix in repair for, anodised aluminium frame powder coating (minimum thickness of powder coating 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. 41 Supply and fix in repair for, anodised aluminium powder coated (minimum thickness of powder coating 50 micron) window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed. 42 Supply and fix, anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement as specified and directed. 43 Supply and fix for, pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed. 44 Supply and fix for, pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed. 45 Supply and fix for 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts screws, in roofs, walls etc. with grade of zinc coating 275, complete all as specified and directed.. 46 Taking down tarfelt with cement plaster from and lowering and removing the same to a distance exc. 50m and not exc.100m including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc., and brushing neat cement slurry with 3.0Kg of cement per sqm, complete all as specified and adirected. 47 Material and labour for, rendering 10 mm (average) thick, cement plaster, in cement mortar (1:3), finished even and smooth without using extra cement mixed with and incuding water proofing compound as per manufactures instructions on roof surfaces and providing 3mm thick (minimum) APP (Atactic Polypropylene Polymer) modified prefabricated five layers, weight not less than 3.5 Kg/ Sqm water proofing membrane, black finished reinforced with non woven polyester matt (weighing not less than 160 gms/ Sqm) with applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per sqm over a coat of bituminous primer @ 0.40 Litre/ Sqm and one coat of bitumen based UV reflective paint with aluminium paint as per manufacturers instruction over APP membrane. The membrane shall be laid using butane torch and sealing all joints etc., complete all as specified in Para 11.44.5 of SSR Part-I and directed. 48 Material and labour for, powder coated aluminium snap grid frame work for false ceiling, size of grid 605 x 605mm, including aluminium main / cross tee section of size 35mmx 23mm x 1.5mm (minimum) and aluminium angle 25mm x 23mm x 1.5mm thick, suitable size GI wire hanging arrangement with adjuster all as specified in clause No.10.38 in SSR Part-I and incuding 4mm thick high pressure steam cured non asbestos fibre cement reinforced multipurpose board as per IS 14862 including taking down existing false ceiling system, complete all as specified and directed. 49 Material and labour for 18/19mm thick block boards, grade 1 quality, exterior grade, decorative type with decorative face veneer on both faces fixed with screws to timber frame-work including taking down old unserviceable boards, complete all as specified and directed. 50 Material and labour for 18/19mm thick block boards, grade 2 quality, interior grade, decorative type with decorative face veneer on both faces fixed with screws to timber frame-work including taking down old unserviceable boards, complete all as specified and directed. 51 Material and labour for, 75mm thick plain cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in plinth protection, finished even and smooth without using extra cement, complete all as specified and directed. 52 Material and labour for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over and including 20mm thick screed bed or bedding in cement mortar (1:6) including taking down old unserviceable granite tiles,complete all as specified and directed. 53 Materials and labour for, glazed ceramic coloured tiles, 450 X 350 X 7mm/ 350 X 250 X 7mm thick, on vertical surface of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick backing coat in cement mortar (1:4) including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. 54 Material and labour for, non skid ceramic tiles, coloured 7 to 8mm thick (square/ rectangular) area of each tile exc.0.06 Sqm but not exc.0.11 Sqm as in floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 15mm thick screed bed or bedding in cement mortar (1:4) including dismantling floor, hearth or wall tiling including cement mortar bedding, removing serviceable tiles to stores and rubbish off the premises, complete all as specified and directed. 55 Material and labour for, non skid ceramic tiles, coloured 7 to 8mm thick (square/ rectangular) area of each tile exc.0.18 Sqm but not exc.0.38 Sqm as in floors, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match colour over and including 15mm thick screed bed or bedding in cement mortar (1:4) including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. 56 All as per serial item No. 55 here-in-before but as in skirting/ dado overcement mortar (1:4) backing coat. 57 Material and labour for, vitrified Ceramic light shade tiles 10 mm thick (square/ rectangular) polished, area of each tiles exc.0.36 sqm but not exc.0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding in cement mortar (1:4) including dismantling floor, hearth or wall tiling including cement mortar bedding, removing serviceable tiles to stores and rubbish off the premises, complete all as specified and directed. 58 All as per serial item No.57.00 but on vertical surfaces over and including 10mm thick backing coat in cement mortar (1:3), complete all as specified and directed. 59 Material and labour for, chequered cement concrete tiles 20cm x 20cm x 25mm thick with grey cement and pigment, set, jointed and pointed in neat cement slurry in floors over and including 15mm thick screed bed or bedding in cement mortar (1:4) including taking down old unserviceable tiles, complete all as specified and directed. 60 Material and labour for, rendering 15 mm thick, cement plaster, in cement mortar (1:6) on fair faces of brick work or concrete surfaces on walls and finished even and smooth without using extra cement including taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and directed. 61 Materials and labour for, rendering 15 mm thick, cement plaster, in cement mortar (1:4) on fair faces of brick work or concrete surfaces on walls and finished even and smooth without using extra cement including taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and directed. 62 Material and labour for, preparation of old plastered or unplastered decorated wall surfaces by washing rubbing downand applying one coat of white wash, complete all as specified and directed 63 Material and labour for, preparation of old plastered or unplastered decorated surfaces and applying one coat of white wash on ceiling, complete all as specified and directed. 64 Material and labour for, preparation of newly plastered wall surfaces and applying two coats of cement base paint over a coat primer, complete all as specified and directed. 65 Material and labour for, complete removal of existing treatment of plastered wall surfaces and applying two coats of cement base paint over a coat primer including preparation of surfaces, complete all as specified and directed. 66 Material and labour for, preparation of old decorated plastered wall surfaces and applying one coat of cement base paint, complete all as specified and directed. 67 Material and labour for, complete removal of existing treatment on plastered wall surfaces and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, complete all as specified and directed. 68 Material and labour for, preparation of plastered wall surfaces and applying two coats of 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre of required shade and colour complete, as per manufacturers specification over 1mm thick wall care putty on plastered surfaces, complete all as specified and directed. 69 Material and labour for, complete removal of existing treatment on plastered wall surfaces and applying two coats of 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre of required shade and colour complete, as per manufacturers specification over 1mm thick wall care putty on plastered surfaces, complete all as specified and directed. 70 Material and labour for, preparation of old plastered or unplastered decorated surfaces and applying one coat of 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre of required shade and colour complete, as per manufacturers specification, complete all as specified and directed. 71 Material and labour for, 4.0mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane, complete all as specified and directed. 72 Material and labour for, 4.0mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane including hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and directed. 73 Material and labour for, 4.0mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane including hacking out old broken glass (any thickness, size, quality or description)from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones, complete all as specified and directed. 74 Supply and fix for, 4.0 figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sq. m in each pane, complete all as specified and directed. 75 Material and labour for, 4.8mm thick tinted glass, selected quality and glazing with rubber packing in square exc 0.5 sqm in each pane, complete all as specified and directed. 76 Material and labour for, preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed. 77 Material and labour for, preparation of old painted wood and wood based surfaces of any description, not otherwise described, not exc.10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed. 78 Material and labour for, preparation of old painted steel and iron surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed. 79 Material and labour for, rewriting/ repainting letters or figures (Block, Roman, Italic or Indian) n exc. 30 cm high with synthetic enamel paint, complete all as specified and directed. 80 Material and labour for, obliterating old writing of any description, not exc 0.1 sqm, with synthetic enamel paint to match existing work, complete all as specified and directed. 81 Supply and fix in repair for, bib tap, fancy type, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15 mm bore, complete all as specified and directed. 82 Supply and fix, pillar taps, fancy type, cast copper alloy, chromium plated, with capstan heads,screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for 15mm bore iron pipe, complete all as specified and directed. 83 Supply and fix in repair for, pillar taps, fancy type, cast copper alloy, chromium plated, with capstan heads,screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for 15mm bore iron pipe, complete all as specified and directed. 84 Supply and fix in repairs for, stop valves, fancy type, chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore, complete all as specified and directed. 85 Supply and fix in repair for, 15mm dia bib tap standard fancy type of PTMT any colour high pressure screwed for iron pipe, complete all as specified and directed. (Minimum weight 15mm-90gms). 86 Supply and fix in repairs for, brass chromium plated shower rose 125mm size with or without swivel joints with 225mm long arms, cast copper alloy chromium plated,fixing to 15mm steel pipe or union, complete all as specified and directed. 87 Supply and fix in repair for, 15mm dia brass CP fancy wall mixer 2 in 1 with L bend with provision of OH shower for mixing hot and coldwater, screwed down for iron pipe and fixedall as per Cat No.CQT-23273UPR of Jaquar or equivalent model of make as specified in PS, complete all as specified and directed. 88 Supply and fix for 15mm bore tubes, medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed. 89 Taking up or down steel tubing 15mm bore and connections, including cleaning and refixing old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.), complete all as directed. 90 Supply and fix for 20mm bore tubes, medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed. 91 Taking up or down steel tubing 20mm bore and connections, including cleaning and refixing old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.), complete all as directed. 92 Supply and laying of 16mm CPVC pipes SDR 11 and plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified and directed. 93 Supply and laying of 20mm CPVC pipes SDR 11 and plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified and directed. 94 Supply and fix in repair for, 15mm bore gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed. 95 Supply and fix in repair for, 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe, complete all as specified and directed. 96 Supply, hoisting and fixing in position of rotational moulded polyethylene water storage tanks in double layers (cylindrical vertical with closed top) of 500 litres capacity with ISI marked and all as specified in IS12701, specified in SSR Part I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule of size 20mm dia including taking down existing water tank, complete all as specified in SSR Part I and directed. 97 Supply, hoisting and fixing in position of rotational moulded polyethylene water storage tanks in double layers (cylindrical vertical with closed top) of 1000 litres capacity with ISI marked and all as specified in IS12701, specified in SSR Part I including ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule of size 20mm dia including taking down existing water tank, complete all as specified in SSR Part I and directed. 98 Disconnecting existing tanks of 500 litres capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position (Cleaning repairing, etc. measured separately), complete all as directed. 99 Supply and fix in repairs for, sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and directed. 100 Supply and fix for, vitreous china wash basin, white, flat back, size 550 x 400mm excluding taps, chain and plug and porcelain stopper but including brackets, 32mm dia corrugated PVC waste pipe, chromium plated coupling 32mm dia, 15mm dia PVC connections and cutting for and pinning in ends of brackets or erecting stand, complete all as specified and directed. 101 Supply and fix for in repair, vitreous china squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe), connection to trap and to flushing cistern anti syphonage pipe including provision of PCC or lime concrete bedding and removal of debris, complete all as specified and directed. 102 Supply and fix in repairs for, vitreous china wash down water closet pan (EWC) (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) with and including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed. 103 Supply and fix in repairs for, health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. 104 Supply and fix in repair for, vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing, grating and union for discharge pipe (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), complete all as specified and directed 105 Supply and fix in repairs for, PVC valveless, syphonic action type, dual flush, flushing cistern 10 litres capacity, low level, white, with inlet, ball valve, float and handle with flush pipe of polyethylene of low or high density or PVC 32mm dia long bend including PVC connection cutting & pinning in ends, making good the disturbed surfaces in cement mortar (1:3), complete all as specified and directed. 106 Supply and fix in repair for, 32mm bore PVC corrugated waste pipe suitable for kitchen sink/ wash hand basin, complete all as specified and directed. 107 Supply and fix for, sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified and directed. 108 Supply and fix in repair for, 600mm x 450mm bevelled edge mirror of selected quality 5 to 6mm thick glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and directed. 109 Supply and fix in repair for, PVC box type minor cabinet selected quality of size 45cm x 35cm x 15cm thick coloured fixed with 04 Nos screws fixed on wall, complete all as specified and directed. 110 Supply and fix in repair stainless steel kitchen plate rack 24 x 24 x 10 including necessary fitting/ fixing accessories all as per Cat No.P-310 of Prayag make or equivalent model of make specified in PS, complete all as specified and directed. 111 Supply and fix in repair for, soap dish, stainless steel, fixed to plugs with chromium plated brass screws, complete all as specified and directed. 112 Supply and fix in repair for, toilet paper holder with flat recessed type stainless steel, complete all as specified and directed 113 Supply and fix in repair for, steel CP grating 100mm dia as per Cat No.FT-62 of Prayag or equivalent model of make as per PS, complete all as specified and directed. 114 Supply and fix for, 50mm bore UPVC low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq.cm including cutting, chasing, pinning and making good the floor as per existing, complete all as specified and directed. 115 Supply and fix for, 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts, bolts etc., including taking down old unserviceable pipe, complete all as specified and directed. 116 Supply and fix for, 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc. including taking down old unserviceable pipe, complete all as specified and directed. 117 Supply and fix for, 75mm bore PVC (SWR) bends any radius, complete all as specified and directed. 118 Supply and fix for, 110mm bore PVC (SWR) bends any radius, complete all as specified and directed. 119 Supply and fix for, 75mm bore PVC (SWR) junction single, (Single T) equal or unequal, complete all as specified and directed. 120 Supply and fix for, 110mm bore PVC (SWR) junction single, (Single T) equal or unequal, complete all as specified and directed. 121 Supply and fix for, PVC (SWR) floor trap 75mm dia, plain with CP grating including jointing with solvent cement, complete all as specified and directed. 122 Supply and fix for, PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement, complete all as specified and directed.
