General Maintenance/Upkeeping Of Shri Amarnath Ji Yatra- 2025 (Sanjy-2025) In The Jurisdiction Of Sub Division Kathua For The Year 2025-26 (Under Capex And Revex Budget On Account Of Shri Amarnath Ji Yatra,2025)(2Nd Call) Refer To Boq- 1 Providing and fixing white vitreous china water closet squatting pan(Indian type) Orrisa pattern size580 x 440 mm (Hindware/ Cera/ Parryware or eqivalvalent make)complete job. 2 Providing & fixing white vitreous china pedestal type (European type/ wash down type) water closet pan (Hindware/Cera/Parryware or eqivalvalent make)complete job. 3 Providing and fixing controlled flush, low level cistern made of vitreous china with all fittings complete.10 litre capacity-White complete job. (Hindware/Cera/Parryware or eqivalvalent make) 4 Providing and fixing P.V.C low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittingsand fixtures complete: 10 liter capacity -White 5 Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fitting complete semi rigid pipe 32 mm dia 6 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required . Kitchen sink without drain 610 x 510 mm with bowl depth 200 mm 7 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260 x 350mm and 340 x 410 x 265mm sizes respectively with automatic flushing cistern with CI/MS brackets standard size of G.I. flush pipe and C.P. brass spreaders with brass unions and G.I. clamps completeincluding painting of fitting and brackets, cutting &making goods the walls & floors wherever required. One urinal basin with 5 litre P.V.C. automatic flushing of approved quality 8 Providing andplacing on terrace (atallfloorlevels ) polythyleneWaterStorageTankISI: 12701marked indicating theBIS License No. with cover and suitable locking arrangement and making necessary holes forintlet, outlet and overflow pipes but without fittingand the base support for tank (Sintex, Electroplast, Star, Lotus or equivalent having valid ISI license ) 9 Providing and fixing 15 mm nominal bore C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms 10 Providing & fixing 15mm nominal bore C.P. brass angle valve for basin mixer and gyser points of approved for conforming to IS : 8931 11 Providing and fixing brass bib cock of approved quality.15 mm nominal bore 12 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 liter low level white P.V.C. flushing cistern, including flush pipe with manually controlled device (handle lever), conforming to IS:7231, with all fittings and fixtures complete, includingcutting and making good the walls and floors whereverrequired. W.C. pan with ISI marked white solid plastic seat and lid. 13 Providing & fixing wash basin with C.I./M.S. brackets, 15mm C.P.brasspillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting & making good the walls wherever required(Hindware/Cera/Parryware or eqivalvalent make) White Vitreous China wash basin 630 x450mm with a single 15mm C.P. brasspillar taps complete job. 14 Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. (Hindware/Cera/Parryware or eqivalvalent make) 15 Providing and fixing 600 x 450 beveled edge mirror of superior glass (ofapproved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 16 Providing & fixing unplasticised P.V.C. connection pipe with brass union 30 cm length 15mm nominal bore 17 Providing &fixingC.P. brass shower rose with 15 mm or 20 mm inlet 150mm diameter complete job. 18 Providing and fixing C.P hand spray with lever control (health faucet) and flexible hose 1 mtr long connection with C.P holder for hand spray complete in all respects as per direction of Engineer-In-charge 19 Providing and fixing Polyethelene-Aiuminium-Polyethelene (PE-AL-PE) Composite Pressure Pipes conforming to IS:15450 U.V. stablised with carbon black having thermal stability for hot and cold water supply, capable to withstand temperature upto 80°C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) eg. Elbows, tees, reducers, couplers and connectors etc. with clamps at one metre spacing. This includes the costs of cutting chases and including testing of joints complete as per direction of the Engineer-in-charge. (Internal work concealed with clamps at 1.00 meter spacing including cutting the chases and making good the wall etc.) 20 1620(20mm OD) pipe 21 2025(25mm OD) pipe 22 2532 (32mm OD) pipe 23 Providing and fixing Polyethelene-Aiuminium-Polyethelene (PE-AL-PE) Composite Pressure Pipes conforming to 15:15450 U.V. stabilised with carbon black having thermal stability for hot and cold water supply, capable to withstand temperature upto 80°Cincluding all special fittings of composite material (engineering plastic blend and brass inserts wherever required) eg. Elbows, tees, reducers,couplers and connectors etc. with clamps at one metre spacing. This includes testing of joints complete as per direction of the Engineer-in-charge.Internal work-exposed on wall with clamps at 1.00 meter spacing 24 1620(20mm OD) pipe 25 2025(25mm OD) pipe 26 2532 (32mm OD) pipe 27 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge. Internal work-exposed on wall with clamps at 1.00 meter spacing. 28 PN-16 pipe , 40mm OD(SDR-7.4) 29 PN-16 pipe , 32mm OD(SDR-7.4) 30 PN-16 pipe , 25mm OD(SDR-7.4) 31 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge. Internal work.(Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc..) 32 PN-16 pipe , 32mm OD(SDR-7.4) 33 PN-16 pipe , 25mm OD(SDR-7.4) 34 Providing & fixing G.I. pipes complete with G.I. fitting and clamps including cutting and making good the walls etc.Internal Work-Exposed on wall 35 15mm nominal bore Medium 36 20mm nominal bore Medium 37 25mm nominal bore Medium 38 Providing & fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc complete 39 15mm nominal bore Medium 40 20mm nominal bore Medium 41 25mm nominal bore Medium 42 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge.Internal work-exposed on wall, including fixing the pipe with clamps at 1.00 meter spacing 43 15mm nominal outer dia pipes. 44 25mm nominal outer dia pipes 45 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge.Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. 46 20mm nominal outer dia pipes. 47 25mm nominal outer dia pipes. 48 Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes 49 75mmdia 50 110 mmdia 51 150 mmdia 52 Providing and fixing on wall face un-plasticized - PVC moulded fittings/ accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansio 53 75mmdia Plain bend 54 110 mmdiaPlain bend 55 Providing and fixing15 mm nominal bore C.P. stop cock (concealed) of standard design and of approved make conforming to IS : 8931 56 Providing and fixing15 mm dia nominal bore C.P. brass long nose bib cock of approvedconforming to IS standards and weighing not less than810 gms 57 Providing & fixing 15mm nominal bore Plastic bib cock 58 Providing & fixing 15mm nominal bore Plastic Angle Valve 59 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 60 15mm nominal bore 61 20mm nominal bore 62 25mm nominal bore 63 Supplying of Following Sanitary and Water Supply fittings:- 64 Inner face of approved quality 65 Disk face of approved quality 66 Jet of approved quality 67 Pillar Cock brass of approved quality 68 G.I Elbow 15mm of approved quality 69 G.I Elbow 20mm of approved quality 70 G.I Elbow 25mm of approved quality 71 G.I Socket 15mm of approved quality 72 G.I Socket 20mm of approved quality 73 G.I Socket 25mm of approved quality 74 G.I Tee 15mm of approved quality 75 G.I Tee 20mm of approved quality 76 G.I Tee 25mm of approved quality 77 G.I Reducer 15mmx 20mm of approved quality 78 G.I Reducer 25mmx 20mm of approved quality 79 G.I Reducer 15mmx 25mm of approved quality 80 G.I Elbow 15mmx20mm of approved quality 81 G.I Elbow 20mmx25mm of approved quality 82 G.I. Elbow 25mmx15mm of approved quality 83 G.I. Nipple 15x 50mm of approved quality 84 G.I. Nipple 15x 100mm of approved quality 85 G.I. Nipple 15x150mm of approved quality 86 G.I. Nipple 20 x 50mm of approved quality 87 G.I. Nipple 20x 100mm of approved quality 88 G.I. Nipple 20x 150mm of approved quality 89 G.I. Nipple 25x50mm of approved quality 90 G.I. Nipple 25x100mm of approved quality 91 G.I. Nipple 25x150mm of approved quality 92 White Cement 1 Kg pack of approved quality 93 Cistern Syphon of approved quality 94 Cistern Handle of approved quality 95 Cistern Vassel of approved quality 96 W.C. Seat Cover White/Coloured of approved quality 97 C.P. Nipple of approved quality 98 C.P. Grating of approved quality 99 C.P. Cup of approved quality 100 Towel Rod of approved quality 101 Towel Ring of approved quality 102 PVC Collar 75mm,100mm of approved quality 103 P.V.C Floor Trap of approved quality 104 P.V.C Tee of approved quality 105 G.I Check Valve of approved quality 106 P.V.C Cistern ball Cock of approved quality 107 Float Valve brass of approved quality 108 Tank Nipple of approved quality 25 mm , 20 mm 109 Waste Coupling of approved quality 110 C.P Soap Dish of approved quality 111 CPVC Union 20mm of approved quality 112 CPVC Union 25mm of approved quality 113 CPVC Ball Valve 20mm of approved quality 114 CPVC Ball Valve 25mm of approved quality 115 CPVC Brass MTA 20x15mm of approved quality 116 CPVC Brass MTA 20x20mm of approved quality 117 CPVC Brass MTA 20x25mm of approved quality 118 CPVC Brass FTA 20x15mm of approved quality 119 CPVC Brass FTA 20x20mm of approved quality 120 CPVC Brass FTA 20x25mm of approved quality 121 Providing and fixing aluminium tower bolts ISImarked anodised (anodic coating not less than grade AC10 as per IS:1868) transparent or dyedto required colour or shade with necessary screws etc complete 122 100 x 10 mm 123 150 x 10 mm 124 200 x 10 mm 125 Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc complete. 100 x 10 mm 126 Providing and fixing aluminium handles ISI marked anodised (anodic coating not less thangrade AC10 as per IS:1868) transparent or dyedto required colour or shade with necessary screws etc complete 127 100mm 128 125mm 129 Providing &fixing aluminum sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to req. colour or shade with nuts & screws etc. complete: 130 300 x 16mm. 131 250 x 16mm. 132 Providing and fixing aluminium hanging floor doorstopper ISI marked anodised(anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: Twin rubber stopper 133 Door closer Spring Type of approved quality 134 Door Closer Hydraulic of approved quality 135 Renewing Glass panes and refixing existing wooden fillets Float Glass Panes of thickness 4.0 mm (weight not less than 10 kg/ sqm) 136 Renewing Glass panes, withPutty & Nails wherever necessary float Glass Panes of thickness 4 mm (weight not less than 10 kg/ sqm) 137 Butt Hinges 3 of approved quality 138 Butt Hinges 4 of approved quality 139 Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable materialin cement mortar, all leads & lifts. 140 Demolishingcement concrete1 : 3 : 6 or richer mix manually/ by mechanical means including disposal of material, all leads & lifts. 141 DemolishingRCC work manually /by mechanical means including stackingofsteel bars anddisposal of unserviceable material ,all leads & lifts. 142 Demolishing mud phaska in terracing and disposal of material including all leads & lifts. 143 Demolishing brick tile covering in terracing including stacking of serviceable material & disposal of unserviceable material including all leads & lifts. 144 Painting top of roofs with bitumen of approved quality at 17 kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm incl. cleaning the slab surface with brushes and finally with a piece of cloth lightlysoaked in kerosene oil complete with residual type petroleum bitumen of grade VG-10. 145 10 cm thick mud phaska of damped brick earth on roofslaid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa at 35 kg/cum of earth and gobri leaping with mix 1 : 1 ( 1 clay : 1 cow dung) andcovered with flat tile bricks of class designation 100 grouted with cement mortar 1:3 mixed with 2% of integral waterproofing compound by weight of cement & finished neat withcommon burnt clay (non modular) brick tile of class designation 10.0 incl. all leads, lifts & carriage of material by MT/ H.L. 146 Providing & laying400 micron thick transparent Poly Vinyl Chloride sheeton the roof under mud phaskacutting placingcomplete job. 147 Making Khurras45 x 45 cm with average minimumthickness of 5 cm cement concrete 1:2:4 ( 1 cement : 2 Coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1 m x 1m x 400 micron, finished with 12 mm cement plaster 1:3 ( 1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges, making and finishing the outlet completeincl. all leads, lifts & carriage of material by MT/ H.L. 148 Providing gola 75 x 75 mm in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 stone aggregate 10mm down gauge) including finishing with cement mortar 1:3 ( 1 cement : 3 fine sand) as per standard design in 75 x 75 mm deep chase incl. all leads, lifts & carriage of material by M.T / H.L. 149 Regrading terracing of mud phaska covered with tiles or bricks, in cement by dismantling tiles or bricks, removing mud plaster preparing the surface of mud phaska to proper slope, relaying plaster gobri leaping and tiles and bricks, grouted in cement mortar 1:3 (1 cement :3 fine sand ) including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground (the cost of the new tiles or brick excluded) including all leads, lifts & carriage of material by MT / H.L. 150 Taking out doors, windows,windows and clerestory window shutters (steel or wood) of area of 3 square metres and below including stackingof material, allleads and lifts. 151 Dismantling old plaster or skirting, raking out joints & cleaning the surface for plaster including disposal ofrubbish to the dumping ground with all leads & lifts. 152 Dismantling tile work for thickness of tiles 10 mm to 25 mm in floors and walls laid in cement mortar including stacking material, all leads & lifts. 153 Dismantling woodentrellis workexcluding frames but including stacking the serviceable material including all leads & lifts. 154 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking of area 3 sqm and below ,all leads & lifts. 155 Dismantling of flushing cistern of all types ( C.I /PVC/Vitreous china) incl. stacking of useful materials near the site & disposal of unserviceable materials incl. all leads, lifts & carriage of material by MT/H. L. 156 Dismentling C.I. or Asbestosrain water pipes of 100 mm dia pipes with fittings and clamps including stacking the material , all leads & lifts. 157 Removing mortar from brick workin cement mortarand cleaning bricks including stacking of material,all leads & lifts ( stacks of cleaned bricks shall be measured). 158 Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits & the like not exceeding 10 sqm on plan, including dressing of sides & ramming of bottoms , incl. disposal or filling of excavated earth wherever requiredas per the directions of Engineer-in-charge . 159 Providing &layinginpositioncement concrete 1:5:10 (cement : 5coarsesand : 10gradedcrushedstoneaggregate40 mm nominal size) ofspecifiedgradeexcl.thecostofcentring & shuttering incl. all leads, lifts & carriage of material by MT/ H.L.- All work upto plinth level. 160 Providing and laying in position cement concrete 1 : 4 :8 ( 1 cement : 4 coarse sand : 8 graded crushed stone aggregate 40 mm nominal size) of specified grade excluding the cost of centring and shuttering including all leads, lifts and carriage of material by MT / H.L.-All work upto plinth level. 161 Providingandlayinginposition cement concreteof specified grade excluding the cost of centring and shuttering- All work upto plinth level. 1 : 3 : 6 (1 cement:3 coarse sand:6graded crushed stone aggregate20 mm nominal size ) including all leads, lifts and carriage of material by MT / H.L 162 Providingandlayinginposition cement concreteof specified grade excluding the cost of centring and shuttering- All work upto plinth level. 1 : 1.5: 3 (1 cement:1.5 coarse sand:3graded crushed stone aggregate20 mm nominal size ) incl. all leads, lifts and carriage of material by MT / H.L 163 Providingandlayinginposition cement concreteof specified grade excluding the cost of centring and shuttering- All work upto plinth level. 1 : 2 : 4 (1 cement:2 coarse sand:4graded crushed stone aggregate20 mm nominal size ) including all leads, lifts and carriage of material by MT / H.L 164 Providing and laying damp proof course 40 mm thick with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20 mm nominal size)including all leads, liftsand carriageof material by MT/H.L. 165 Providing and laying damp proof course 50 mm thick with cement concrete1 : 2 : 4 ( 1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20 mm nominal size)including all leads, lifts and carriageof material by MT / H.L. 166 Providing and laying dry stone agg. using 40mm nominal size incl. spreading, levelling,sand grouting, watering, ramming, etc all complete incl. all leads, lifts & carriage of material by MT / H.L. 167 Brick work common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curring in Cement mortar 1:6 ( 1 cement : 6 coarse sand)including all shapes,leads, lifts and carriage of material by MT / H.L. in cement mortar 168 Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level incl. all leads, lifts and carriage of material by M.T. H.L. 169 Half brick masonrywith bricks of class designation 7.5 in foundations and plinth in cementmortar 1:4 ( 1 cement :4coarse sand)including all leads, lifts and carriage of material by MT / H.L. 170 Extra for half brickmasonry in superstructure above plinth level upto floor V levelincluding all leads, lifts and carriage of material by M.T. H.L. 171 12mm cement plaster of mix 1:4 (1 cement : 4 fine sand) incl. all leads, lifts & carriage of material by MT / H.L. 172 15mm cement plaster on rough side of single or half brick wall of mix 1:6 (1 cement : 6 fine sand) includingall leads, lifts and carriage of material by MT / H.L. 173 Repairs to plaster of thickness 12 mm to 20 mm with cement mortar 1:4 (1 cement : 4 fine sand) in patches of area 2.5 sq. metres & under including cutting the patch in proper shape ranking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 metres lead. 174 Making plinth protection 50 mm thick of cement concrete 1:3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm bed of dry brick ballast 40 mm nominal size well rammed & consolidated & grouted with fine sand including finishing the top smooth. Crushed aggregate including all leads, lifts and carriage of material by MT/H.L. 175 Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1.5:3 (1 cement : 1.5coarse sand :3graded stone agg. 20 mm nominal size)incl. all leads, lifts & carriage of material byMT/ H.L. . 176 Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size). incl. all leads, lifts and carriage of material by MT/H.L. 177 Reinforcement for RCC work including straightening,cutting, bending, placing in position and binding allcomplete Thermo Mechanically Treated bars /Cold twisted bars including all leads, lifts and carriage of material by MT / H.L. 178 Centring and shuttering including strutting propping etc and removal of form work for 179 Foundations, footings, bases of columns etc. for massconcrete 180 Lintels, beams, plinth beams, girders,bressumers and cantilevers 181 Suspended floors, roofs, landings, balconies andaccess platform. 182 Edges of slabs and breaks in floors and wallsunder 20 cms wide. 183 Raking out joints in lime or cement mortar and preparing the surface for repainting or replastering including disposal of rubbish to the dumping ground with all leads and lifts. 184 Flush pointing with cement mortar 1:3 ( 1 cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement for flat tile bricks on top of mud phaska with non modularbrick tiles 185 Providing wood work in frames ofdoors, windows, clerestory windows and other frames wrought framed & fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or with dash fasteners shall be paid for separately) 186 Sal Wood 187 2nd Class Deodar Wood 188 2nd Class KailWood 189 Providing and fixing 35mm thick wire gauze shutters of Second Class deodar woodusing galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : 190 Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. First class deodar wood 191 Providing and fixing 35mm thick panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with inecessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately).Second class deodar wood 192 Providing and fixing panelling orpanelling and glazing inpanelledorpanelledandglazedshuttersfordoors, windows and clerestory windows (Area of openingfor panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick , Particle Board 12 mm thick plain particle board flat pressed, three layer or graded wood particle board medium density grade IS: 3087 marked. 193 Providing and fixing fly proof galvanised M.S. wire gauge to windows and clerestory windows using galvanised M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete.With 2nd class teak wood beading 62 x 19 mm 194 Providing 40x 5 mm flat iron hold fast 40cm long incl. fixing to frame with 10mm diameter bolts nuts and wooden plugs with embeddings in cementconcrete blocks 30 x 10 x15 cm 1:3:6 mix (1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size including all leads, lifts and carriage of material by MT / H.L. 195 Providing and fixing 16 mm thick gang saw cut mirror polished (pre moulded and pre polished), machine cut for kitchen plateform,vanity counters window sills facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement:4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curring moulding and polishing to edge to give high gloss finish etc. complete at all levelsGranite of any colour and shape(Area of slab upto 0.50 sqm) 196 Providing edge molding to 18 mm thick marblestone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer- in -Charge. for granite work 197 Extra for providing opening of required size andshape for wash basins/ kitchen sink platform, vanity counters and similar location in marble/ stone work includingnecessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete. 198 Providing and laying vitrified floor tiles in different sizes (thickness to be specified bythe manufacturer) with water absorption less than 0.08% & confirming to IS: 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1 : 4 (1 cement : 4 coarse sand) including groutingthe joints with white cement & matching pigments etc.complete size of tile 60 cm x 60 cm including all leads, lifts and carriage of material by MT / H.L. 199 Providing and laying matt finished vitrified tile of specified size having water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in outdoor floors such as footpath, court yard multi models etc., laid on 20mm thick base of cement mortar 1:4 (1cement: 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as direction of Engineer-in-Charge. 300x300x9.8 mm 200 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 201 Providing and fixing 1st quality ceramic glazed floor tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. including all leads, lifts and carriage of material by MT / H.L. 202 Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. allcomplete as per direction of Engineer-in-charge 203 Chequerred precast cement concrete tiles 22mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) . Medium shade using 50% white cement and 50% ordinary cement. 204 Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete 50 mm thick with 20mm nominal size stone aggregate 205 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : including all leads, lifts and carriage of material by M.T/ H.L.Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of classdesignation 7.5 206 Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. 207 Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying a priming coatof approved steel primer using structural steel etc. as required. In grating, frames, guard bar, ladders railing, brackets, gates & similar works. 208 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes 209 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing & staircase railing and similar work includingapplyingapriming coat of approvedsteel primer. G.I.pipes 210 Providing and fixing in position collapsible steel shutters with vertical channels 20 x 10 x 2 mm and braced with flat iron diagonals 20 x 5 mm size with top and bottom rail of T-iron 40 x 40 x 6 mmwith 40 mm dia, steel pulleys complete with bolts, nuts locking arrangement, stoppers, handlesincluding applying a priming coat of approved steel primer. 211 Providing and fixing 1 mm thick M.S. steel door with frame of 40 x 40 x 6 mm angle iron and 3mm M.S. gusset plates at the junction and corners , all necessary fittings complete, including applying a priming coat of approved steel primer.Using flats 30x6 mm for diagonal braces and central cross piece. 212 Providing and fixing M.S. grills of required patternin frames of windows etc with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete 213 Fixed to openings/ wooden frames with Rawl plugs screws etc. 214 Fixed to steel windows by welding. 215 Providing and fixing aluminum work for doors, windows ventilators and partitions with extruded built up standard tubular sections/appropriateZ. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia and size including necessary filling up of gaps at junctions i.e. at top, bottom and sides with required EPDMrubber/neoprene gasketfelt etc.Aluminum sections shall be smooth, rust free, straight, milted and jointed mechanically wherever required includingcleat angle, Aluminum snap beading for glazing/paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge( glazing, paneling and dash fasteners to be paid for separately.) 216 For fixed portion anodized aluminum (anodized transparent or dyed to required shade according to IS : 1868 minimum anodic coating of grade AC 15) 217 For fixed portion Powder coated aluminum ( minimum thickness of powder coated 50 microns) 218 Providing and fixing aluminum work for doors, windows ventilators and partitions with extruded built up standard tubular sections/appropriateZ. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia and size including necessary filling up of gaps at junctions i.e. at top, bottom and sides with required EPDMrubber/neoprene gasketfelt etc.Aluminum sections shall be smooth, rust free, straight, milted and jointed mechanically wherever required includingcleat angle, Aluminum snap beading for glazing/paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge( glazing, paneling and dash fasteners to be paid for separately.For shutters of doors, windows & ventilators including providing and fixings hinges/pivots and making provision forfixingof fittings wherever required including the cost of EPDMrubber/ neoprene gasket required( Fittings shall be paid for separately). 219 Anodised aluminum ( anodized transparent or dyed to required shade according to IS : 1868, minimum anodic coating of grade AC 15) 220 Powder coated aluminum (minimum thickness of powder coated 50 221 Providing and fixing glazingin aluminum door, window, ventilators shutters and partitions etc. with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.( Cost.Of aluminum snap beading shall be paid in basic item) With floating glass panes of 4.0 mm thickness ( weightnot less than 10.00kg/sqm) 222 Providing and fixingACP sheet panelling 4.0 mm thick in Partition/doors of approved quality as per the direction of Engineer- in - Charge (Complete job) 223 Providing and fixing 12mm thick prelaminated three layer medium density (exterior grade) particle board Grade-I, Type-II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in panelling fixed in aluminiumdoors, windows shutters and partition frames with C.P brass / stainless screws etc. compete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides. 224 Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 minimum anodic coating of Grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing windows frame with C.P. brass/stainless steel screws@ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (only weight of grill to be measured for payment) 225 Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. 226 Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, having brand logo em,possed on the body/plate with double spring mechanism and door weight upto 125 kg for doors including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing & cover plateswithbrasspivot& singlepiece M.S.sheetouter box with slide plate etc. complete as per the direction of Engineer-in-charge.With Stainless Steel cover plate minimum 1.25mm thickness. 227 Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc.including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts & bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) complete job. 228 Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets. 25mm dia (heavy type). 229 Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 230 Providing and Fixing of PVC Panelling including cutting jointing, fixing etc complete job of good quality 231 Providing and Fixing of PVC false ceiling including cutting jointing, fixing etc complete job of good quality 232 Removingdryoroilbound distemper, waterproofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 233 Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. With water thinnable cement primer onwall surface having VOC content lessthan 50 grams/liter 234 Distemperingwith oil bound washable distemper of approved brandandmanufacture togiveanevenshade. Newwork(two or more coats ) over & including primingcoat with cement primer. 235 Distempering with 1st quality Acrylic/oil bound washable distemper (ready-made) having VOC content less than 50 grams/litre of approved manufacturer and of required shade and colour complete as per manufacturers’ specifications, one or more coats on old work. 236 Wall painting with acrylic emulsion paint of approved brand and manufature to give an even shade. Two or more coats on new work. 237 Wall painting with plastic emulsion paint of approved brand and manufature to give an even shade. one or more coats on old work. 238 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.One or more coats on old work. 239 Painting with synthetic enamel paint of approved brand brand manufacture to give an even shade. Two ormore coats on new work 240 Providing and applying White Cement based Putty of average thickness 2 mmof approved brand & manufacture, overtheplastered wall surface to prepare thesurface even & smooth complete. 241 Applying priming coat with ready mixed pink or grey primer of approved brand and manufacture onwoodwork ( hard & soft wood) 242 Finishing walls with water proofing cement paint of required shade:Old work ( one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litres/10 sqm complete including cost of priming coat. 243 Finishing walls with Acrylic smooth exterior paint of required shade: Old work (two or more coats applied @ 1.67 liters/10sqm on existing cement paint surface) 244 Finishing wall with water proofing cement paint of required shade - New work(twoorMore coats) applied @ 3.84 kg/10 sqm 245 Finishing wall with acrylic smooth exterior paint withrequired shade on New work (two or more coats applied) @ 1.67 litre/10 sqm over & including base Coat of water proofing cement paint applied @ 2.20 kg/10 sqm. 246 Finishing walls with Acrylic smooth exterior paint of required shade Old work ( two or more coats applied @ 1.67 litres/10 sqm on existing cement paint surface) 247 Providing and FixingVinyl Flex Board of superior quality 248 Applying one coat of water thinable cement primer of approved brand and manufacture on wall surface . 249 Color washing such as green blue or buff to give an even.New work ( two or more coats) with a base coat of white washing with lime. 250 White washing with lime to give an even shade on New work (three or more coats) 251 White washing with lime to give an even shade : Old work (two or more coats) 252 Labour Charges for Carpentor/ Mason/Plumber/Electrician /Welder or equavailent skilled type 253 Labour Charges for Mazdoor/Helper 254 Hire Chargesof shuttering plates 255 Hire charges of Welding/ gas weldingset including cost of weding rods etc. 256 Providing and fixingwall to wall matting (complete item) 257 Providing and fixingwall to wallfloor acrylic carpeting (complete item) 258 Water proof Pagoda of size 10x 10ft 259 Water proofPagoda of size 20x 20ft 260 Water proof Pagoda of size15x 15ft 261 Supplying and filling at site Good earth including all leads, lifts and carraige of material. 262 Supplying and laying including digging, carrying by lorry, filling River Bed Material including watering & consolidation in layers to specified lines, camber,grades and cross sections. Finished work including material , labourall leads , lifts and carriage of material by MT/HL. 263 Making soak pit 2.5 m diameter 3.0 meter deep with 45x45 cm dry brick honey comb shaft with common burnt clay (non modular) bricks of class designation7.5 bricks & S.W. drain pipe 100 mm diameter, 1.8 m longcomplete as per standard design 264 Providing and fixing fibre sheet for making toilet/bath unit/other partitions of approved quality 265 Construction of temporary toilets including arrangements of angles, fixing of angles & covering withpolythene sheet including carriages, complete job . 266 Supplying and filling of stone dust at site, including all leads, lifts and carriage of material byMT / H.L.etc. complete 267 Supplying of Following Tent houseitems fittings:- 268 Hire Charges for Providing & installation of Shamiana of size 15-0// x 15/-0// with side curtain complete job. 269 Hire Charges for Providing and laying matting /red mat complete job. 270 Hire Charges for providing and installation of Table with paper roll etc.complete job,per No. per Day. 271 Hire Charges for providing and installation of Plastic Chairs complete job,per No. per Day. 272 Hire Charges for providing and installation of VIP Chairs complete job, per No, per Day. 273 Hire Charges for providing and installation of Pedestal fans Complete job, per No. per Day. 274 Hire charges for providing and installationof 3 seater VIP Sofa complete job 275 Hire charges for providing and installation of 2 seater VIP Sofa complete job 276 Providing and installation of stage including construction of front decorative4 ft height ( with certified drawing and design of load bearing capacityof minimum 15 person at a time ) for sitting arrangements of VIPs by way of providing and installation of temporary columns and beams covered with decorative clothes of different colours with polythene sheet over it, including carriages (Complete job) . 277 Providing and installation of stage includingwater proofing roof(temporary) for sitting arrangements of VIPs by way of providing and installation of temporary columns and beams covered with decorative clothes of different colours with polythene sheet over it, including carriages (Complete job) . 278 Providing and fixing/writing of flex board including proper anchoring legs/stand (Complete job) . 279 P/F of Radium Light Reflector writing to Sign Boards incl. carriages to the site complete job (Complete job) . 280 P/F of Sign Boards of Iron Sheet of Size 3x2 incl. painting, writing and embedding the legs in cement concrete incl. carriages to the site 281 Providing and fixing/writing ofmain informatory boardincluding proper anchoring legs/stand (Complete job) . 282 Providing and installation of 2.50 tonne capacity of air conditioner at VIP stage complete job 283 Providing and fixing inauguration stone (granite of size 3/x 2/)incl.engraving , painting, writingand const. of pedestal of size 4-6x 5-6 by way of brick work andplastering, painting incl.all leads , lifts and carriage of material by M.T. /H.L.
