Conversion work of Paikar GP HQ to SSK-health wellness center at Rampurhat HD.-1 Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. Plaster (to wall, floor, ceiling etc.) with sand and cement mortarincluding rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/stcging where necessary (Ground floor). [Excluding cost of chipping over concrete surface] With 1:6 cement mortar 20 mm thick plaster 1st Floor Gound floor Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. In ground floor including roof. (a) upto 150 mm. thick Ordinary Cement concrete (mix 1:2:4) with graded stone chips (6mm nominal size) excluding shuttering and reinforcement, if any, in gound floor as per relevant IS codes. Pakur variety Ground Floor Brick work with 1st class bricks in cement mortar (1:6) (ii) In superstructure, ground floor 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. Supplying bestindian sheet glass panes set in putty and fitted and fixed with nail sand putty complete. (Inall fioorsforinternalwall &upto6 m height for external wall) Supplying and laying true to line and level Vitrified tiles of approved brand (size not less than 600 mm x 600 mm x 10 mm thick in floor, skirting etc. set in 20 mm sand cement mortar(1:4) and 2 mm thick cement slurry back side of tiles using cement@ 2091 kg./sqM or using polymerised adhesive (6mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after applicatiopn slurry using 1.75 kg of cement per sqM below mortar only, joint grouted with admixture of white cement and colouring pigment to match with colour of tiles? epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warn water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials labour and all other incidental charges complete true to the manufacturers specification and direction of Engineer-in-charge. )white cament, synthetic adhesive and grout materials to be supplied by the contrre). (B) Light Colour Ground Floor 1st Floor Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (B) Wall With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement@ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (a) Area of each tile upto 0.09 Sq.m (ii) Other than Coloured decorative including white 1st Floor (A) Floor With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of using cement @2.91 Kg/Sq.m & joint filing using white cement slurry @ 0.20kg/Sq.r (a) Area of each tile upto 0.09 Sq.m (i) Other than Coloured decorative including white 1 st Floor Supplying and laying chequered tiles of any shade & of approved quality with (1:16:3) co concrete laid in panels or patterns as directed inpavement, foot path etc. including neces under lay 25 mm thick (avg) cement mortar (1:3) complete in all respect with all labour a materials. [Using cement slurry @4.4kg/Sq.matbacksideand@24kg/Sq.m for joint fillir Floor Supplying 1.5 mm thick M.S. sheet fitted and fixed on one or both faces of M.S./W.I. ga etc. with point weld in gat not more than 150 mm a part completa in all respect as per de including costof all labour and materials. Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acry primer (as per manufacturers specification) including cleaning and smoothning of surfa Two Coats Ordinary Cement concrete (mix 1:1.5.3) with gracied stone chips (20 mm nominal size excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes Roof Roof treatment by application of non toxic polyurethane modified acrylic based single component (PU Roof Coat) solvent free, cold applied polyurethane modified elastomer waterproofing membrane with excellant UV resistant capesity as per ASTM D6083fa wa based 100%acrylic elastomeric emulsion polymer latex coating used as protective coating roofs) after preparing the surface by cleaning and repairing the roof cracks by cement & mortar (1:4), preferably with antishrinkage mortar (to be paid separately) if any, apply tv coats along with a IPrimingcoat(two coats of P U Roof Coat and one cost of primer coa compatible with Sqm. i main product as per manufacturers specification) and reinforced w or without gam GectextileFleece, including the cost of primer coat and basepreparation, # & Plantsbut excluding the cost of scaffolding and stagging complete as per direction o Engineer-in-charge. (Note: If Geotextile Fleece not uesd the rate would be reduced Labour for taking out door and window frame including shutter for repair or replace ment different parts of the frame & refixing the same including mending good all damaes complete (Concrete and brick work for manding damage will be paid separately) Labour for Chipping of concrete surface before taking up Plastering work. Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, In Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). Neem, Jam, Jackfruits Ground Floor 1st Floor Z-batten shutters of door and window as per design having stongued and groove half joint as per directionof the Engineer-in-Charge including fitting and fixing shutter inposition, be excluding thecost of hinge sand other fittings in ground floor Ground Floor (A) Shutter with 25mm thick planks, 19mm thick battens Sishu, Gamar, Champ, Badam, Bhola, Mogra, Hallak (B) Shutter with 19mm thick planks, 19mm thick battens. Sishu, Gamar, Champ, Badam, Bhola, Mogra, Hallak 1st Floor (A) Shutter with 25mm thick planks, 19mm thick battens. Sishu, Gamar, Champ, Badam, Bhola, Mogra, Hallak (8) Shutter with 19mm thick planks, 16mm thick battens. Sishu, Gamar, Champ, Badam, Bhola, Mogra, Hallak Supplying, fitting & fixing M.S clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete (1:24) as per direction. (Cost of concrete will be paid separately.) (a). 40 mmx 6mm, 250 mm length. fron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark, (vii)100mm x 58mm x 1.90mm Iron Socket Bolt of approved quality fitted and fixed (vi) 150 mm long x10 mm dia. Bolt. Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to 1.8. Specification (I.S. 230/72) fitted and fixed complete: (a) With continuous plate base (Hexagonal/Round rod) (vii) 150mm grip x12mm dia rod. (1) Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16mm dia rod with centre bolt and round fitting (c) 250 mm long Applying Exterior grade Acrylic primer of approved quality and brandon plastered or cencrete surface old or new surface to receivedecorative textured (matt finish) or smooth finish acrylic exterioremulsion paint including scraping and preparing the surface throughly, complete as per manufacturers specification and as per direction of thecEIC. Ground floor outside wall Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturers specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. Ground floor outside wall Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidalprofile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be madeon area of finished work). (i) In Roof- a) With 0.5 mm thick sheet M.S. structural works in columns, beams etc. with simple rolledstructural members (e.g. joists. angle, channel sections conformingto IS: 226, IS: 808 & SP (6)- 1964 connected to one another withbracket, gussets, cleats as per design, direction of Engineer-inchargecomplete including cutting to requisite hape and length, fabrication with necessary bolting, metal arc welding conforming tolS: 816- 1969 & IS: 1995using electrodes of approved make andbrand conforming to IS:814-2004, haulage, hoisting and erectionall complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools andplants and labour required for the work including all incidental chages such as electricity charges, labour Insurance charges etc. 1) For structural members of specified sections weighing less than 22.5 Kg./m Reinforcement for reinforced concrete work in all sorts of structures including distribution bars. stirrups, binders etc. Initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 18 gauge black annealed wire at every intersection, complete as per drawing and direction. (a) For works in foundation, nt and upto roof of ground floor/ upto 4m. 6) Tor Steel/Mild Steal Hire and labour charges for shuttering with centering and necessary staging upto 4m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, linteis curved or straight including fitting, fixing and striking out after completion of works(upto roof of ground floor). (a) 25mm to 30mm thick wooden shuttering as per decision & direction of engineer-in-charge. Ground Floor M.S or W. Ornamental grill of approved design joints continuosly welded with M.S W.I Flats and bars of joints windows railing etc. fitted and fixed with necessary screws and lugs in ground floor. (1) Grill weighing above 10 kg/sq. mtr. And up to 16 Kg/sq.mtr. Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19mmx19mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mmth. heat mouldedPVCC channel of size 30mmth, 70mm width out of which 50mm shall be flatand 20mm shallbe tapered in 45 degree angle on either sidesformingstyles; and5mmth. 95mm wide PVC sheet out of which75 mm shallbe flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mmwidePVCsheetoutofwhich75mm shallbe flat and20 mmshallbetaperedonbothsides toform lock rail. Top, bottomand lock rails shall be provided either side of thepanelwith 10mm(5mmx2) th.,20mmwide crossPVCsheetasgapinsert for top rail and bottom rail. Panelingof5mmth. bothsidePVCsheet tobe fitted in theM.S. framewelded/sealed to the styles &railswith 7mm(5mm+2mm)th.x 15mmwide PVC sheet bea ingon inner side and joined to get her with solvent cement adhesive. Anadditiona 15 mmth.PVC stripof 20mmwhichistobestuckontheinteriorsideof theCchannelusing PVCsolven adhesive etc. complete excludingall necessary hard wares asper direction of Engineer-in-Charge. In ground floor. 1st Floor Supplying, Fitting & Fixing Factory made prelaminated P.V.C. door frame of size 50mmx47mm with a wall thickness of 5mm, made out of extruded 5mm Prelaminated PVC sheet miter cut at two corner sand joined with two nos of 1.5 mm long brackets of 15mmx15mm M.S. square tube. The two vertical door profile sare to be reinforced with 19mmx19mm M.S.Square tube of 19gauge, weather seal to be provided through out the frame. The door frame shall be fixed with thewallusing 65/100mm M.S. Screws through the frame by using P.V.C fasteners. Aminimum of 4Nos of screws to be providedfo reach vertical member and minimum 2Nos for horizontal member etc. complete as per Manufacturers specification and direction of Engineer-in-Charge. 1st floor (a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. Priming one coat on timber or plastered surface with synthetic oilbound primer of approved quality including smoothening surfaces by sand papering etc. In Ground Floor A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary (a) On timber or plastered surface: With super gloss (hi-gloss) - (iv) Two coats (with any shade except white) (b) On steel or other metal surface: With super gloss (hi-gloss) - Pipe IEC
