Dam Proofing And Other Minor Repairing And Renovation Works In Hit Office Building.- 1 Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75m 2 a) In ground floor including roof. 3 b) In First Floor including roof. 4 c) In Second Floorincluding roof. 5 d) In Fourth Floor including roof. 6 e) In Fifth Floor including roof. 7 Dismantling all types of masonry excepting cement concrete plain or reinforced,stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. 8 a) In ground floor including roof. 9 b) In First Floor including roof. 10 c) In Second Floorincluding roof. 11 d) In Third Floor including roof. 12 Dismantling R.C. floor, roof, beams etc. includingcutting rods andremoving rubbish as directed within a lead of75 m. including stacking of steel bars. 13 a) In ground floor including roof. 14 b) In First Floor including roof. 15 c) In Second Floorincluding roof. 16 d) In Third Floor including roof. 17 e) In Fourth Floor including roof. 18 f) In Fifth Floor including roof. 19 Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. 20 Cleaning the concrete surface by removing dirt and debris, marking defective locations and removing loose concrete by careful stripping untill hard surface is exposed, cutting the concrete to regular shape, wire brushing the exposed surface and removing debris from site complete as per direction of the Engineer - in - Charge. 21 Cleaning the exposed reinforcement preferably upto full diameter by wire brush, applying two coats of polymer based rust removing compound left for 24 hours, removing the coating and then applying two (2) coats of polymer modified anti corrosive protective coating formulated to inhibit the corrosion of reinforcement as per manufacturers specification] [Mode of measurement:The affected surface area of reinforcement shall be considered for payment] 22 Removing corroded worn out portion of reinforcement (when the area of bar is damaged by more than 25%) by cutting and replacing the same by a new plain round bar of requisite diameter by binding with required lap / welding with old bar, including cost of reinforcement, complete in all respect including removing unserviceable materials from site as per direction of the Engineer - in - charge. Note : Payment on weight (Kg.) of new reinforcement. 23 Applying epoxy based reactive joining agent for joining the old concrete with fresh concrete to be applied within manufacturers specified time as per manufacturers specification. (0.4 Kg / m² of concrete surface) 24 Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness withuired bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor)(c) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work. 25 a) In ground floor 26 b) In First Floor 27 c) In second Floor 28 d) In third Floor 29 e) In fourth Floor 30 f) In 7th Floor 31 Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes. a) Pakur Variety , In Fourth Floor 32 Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. (i) Pakur Variety 33 a) In ground floor 34 b) In First Floor 35 c) In second Floor 36 d) In third Floor 37 e) In fourth Floor 38 e) In 7th Floor 39 Ordinary Cement concrete (mix 1:2:4) with graded stone chips (6mm nominal size) excluding shuttering and reinforcement,if any, in gound floor as per relevant IS codes.. a) Pakur Variety (i) In Ground floor 40 ii) In 1st Floor 41 iii) In 2nd Floor 42 iv) In 3rd Floor 43 v) In 4th Floor 44 vi) In 5th Floor 45 vii) In 7th Floor 46 Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] 47 (ii) With 1:4 cement mortar, 20mm thk. 48 a) In ground floor including roof 49 b) In First Floor including roof. 50 c) In second Floor including roof 51 d) In third Floor including roof 52 d) In fourth Floor including roof 53 d) In fifth Floor including roof 54 d) In 7th Floor including roof 55 (ii) With 1:4 cement mortar, 10 mm thk. 56 a) In ground floor including roof 57 b) In First Floor including roof. 58 c) In second Floor including roof 59 d) In third Floor including roof 60 e) In fourth Floor including roof 61 e) In fifth Floor including roof 62 f) In 7th Floor including roof 63 Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (In all floors for internal wall & upto 6m height for external wall)(i) 3 mm thick (weighing 7.4 kg/Sq.m) 64 Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturers specification and as per direction of the EIC. (In Ground Floor) (a) One Coati) Water based interior grade Acrylic Primer 65 a) In ground floor 66 b) In First Floor 67 d) In second Floor 68 d) In third Floor 69 e) In fourth Floor 70 e) In fifth Floor 71 e) In 7th Floor 72 Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturers specification) including cleaning and smoothning of surface. Two Coats 73 a) In ground floor 74 b) In First Floor 75 c) In second Floor 76 d) In third Floor 77 d) In 4th Floor 78 d) In 5th Floor 79 d) In 7th Floor 80 Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturers specification and as per direction of the EIC. 81 a) In 7th floor 82 Protective and Decorative Acrylic exterior emulsion paint of approvedquality, as per manufacturers specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. Therate includes cost of material, labour, scaffolding and all incidentalcharges but excluding the cost of primer.In Ground floor (Two Coat) 83 a) In 7th floor 84 Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete. 85 a) UPVC Pipes: 86 b) Bend 87.5 degree 87 Making one set of scaffolding only for replacing glass panels, painting, uprooting plant and another repairing works of building and S&P works for external works only with 10m. dia bamboo as main posts at the rate of 1 metre centre to centre and 7.5 cm. dia bamboo ties @ 0.75 metre apart fitting and fixing with necessary coir, nails etc. as perirection of the Engineer-incharge. b) Upto 4th Floor height 88 For Shifting charge 89 Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading intotruck and cleaning the site in all respect as perdirection of Engineer in charge. 90 Supplying, fitting and fixing Closet seat of approved make with lid and C.P. hinges, rubber buffer and brass screws complete.(a) E.W.C.(iv) Bestolite (solid type) white 91 PTMT Pillar Cock - 15 mm. (Prayag or equivalent). 92 PTMT (Polytetra Bib Cock / Stop Cock)( Prayag or equivalent) 93 15 mm 94 Door stopper.(Brass) 95 Compact Compact Ball Valve with SS Handle ForCPVC/ UPVC Fittings.50mm 96 Supplying,fitting and fixing approved brand P.V.C. CONNECTOR whiteflexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia 750 mm long 97 Supplying, fitting and fixing CPVC (Chlorinated Polyvinyl Chloride) pipes of approved make conforming to IS-15778: 2007 . with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made foraccesories, specials.class ii- 50mm 98 Supplying,fitting and fixing approved brand 32 mm dia.P.V.C. waste pipe, with PVC coupling at one end fitted with necessary clamps.1050 mm long 99 Supplying, fitting & fixing factory made foam PVC (density shall not be less than 600 kg/cum) door frame (finished weight of 2.73 kg/mtr.) of size 100mm X 45mm made off with 5mm thick extruded foam PVC sheet, mitre cut at junction of horizontal and vertical member and joined them by heat welding. Entire door frame profiles to be reinforced with steel primer coated 19 SWG 40mm X 20mm M.S. tube. An additional 5mm thick PVC sheet with desired colour/shade to be provided at the exposed surface and three nos 5mm thick PVC sheet to be provided as gap insert. The door frame to be fixed with wall by using 8mm dia. and 100mm long strainless steel screws and PVC fasteners. A minimum of 4 nos. screws to be provided for each vertical member & 2 nos. for horizontal member all complete as per direction of Engineer-in-Charge.(a) Plain Colour. 100 Supplying, Fitting & Fixing 30 mm thick both side prelaminated Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S.frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which isto be stuck on the interior side of the “C” channel using PVC solvent adhesiveetc. complete excluding all necessary hardwares as per direction of Engineer-in-Charge. 101 Taking out door and window shutters and rehanging the same with old fittings.a)With new iron screws. 102 Styles and rails of wooden shutters fitted and fixed complete. (Payment to be made on area of new work only). In Ground Floor:35mm Thick shutter.Ordinary Teak Wood. 103 Panel (made of single plank) of door and window shutters to design as directed:In Ground Floor(Payment to be made on area of exposed new work). (In case of non-supply of single plank penal rate of reduction to a maximum of 30% will be made).19mm Thick panel of 30cm to 45cm width 104 Renewing hinged cleat with old hinge and new screws. Sal : Malayasian 105 Taking out and refixing after oiling and cleaning including adjusting spring ofdifferent type of automatic door closer with necessary screw complete. 106 Iron butt hinges of approved quality fitted and fixed with steel screws, with ISImark. 100mm. X 75mm. X 3.50mm. 107 Easing and oiling, cleaning collapsible gate and repairing tolocking arrangements. 108 Reparing collapsible gate by cutting out all rivets as necessary reassambling all members including welding pieces of channels, sraightening bent bars and rivetting with new rivets and fitting in position and painting two coats. 109 Supplying, fitting and fixing low-down cistern parts. A) Internal fittings for cistern complete of approved make. 110 5 MT load bearing capacity gully pit cover with frame and hinge arrangement for opening of size Cover: 470 mm X 420 mm X 80 mm Frame: 590 mm X 550 mm X 170 mm opening: 380mm x 305mm Weight: 100 kg (approx) 111 Supplying,fitting & fixing of 2-Track / 3-Track Aluminium sliding Window of all Aluminium sections viz.window frame(top,bottom&side frame), shutter (top, bottom, side & interlock member) made of aluminium alloy extrusions conforming to IS733-1983&IS1285-1975,annodised conforming to IS1868-1983, fitted with all other accessories viz.PVC roller,EPDM gasket,maruti lock, screwsetc. including labour charges for fitting & fixing of aluminium 2-track/3-track sliding window with fixing of glass(excluding cost of glass) all complete as per architectural drawings anddirection of Engineer-in-charge.For 2 Track window:Members for Bottom frame@0.875Kg per Mtr. and for Top and Side frame@0.778Kg per Mtr.and for shutter Bottomand Top member@0.472Kg per Mtr.,Style side member@0.493Kg per Mtr. and Inter lock member @ 0.612 Kg per Mtr. 10-12 Micron thickness Annodizing film Natural white 112 Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987.5mm thick coloured / tinted / smoke glass. 113 Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete,Iron Butt Hinges and M.Sclamps.(The quantum should be correted upto three decimals).e) Sal : Malayasian 114 Supplying solid flush type doors of commercial quality, the timber frame consisting of top and bottom rails and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 37.5mm wide battens places both ways in order to make the door of solid core and internal lipping with Garjan or similar wood veneers using phenol formaldehyde as glue etc.complete, including fitting, fixing shutters in position but excluding the cost of hinges and other fittings in ground floor. (a) 35 mm thick shutters (single leaf) 115 Hand Shower(Health Faucet) with 1mtr Fexible Tube with Wall Hook(Equivalent to Code No.573 & Model -ALLIED of Jaquar or similar). 116 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) inseventh floor. 117 Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. 118 Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary…. On timber or plastered surface.Two coats (white in shade) 119 Added:- @ 18% as GST 120 Added:- @ 1% as labour cess
