Tender For Maintenance Of Staff Quarters Of Csio Colony, Chandigarh 2025-26.; 1 Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming ofbottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. 2 Supplying and filling in plinth with jamuna sand under floors, including watering,ramming, consolidating and dressing complete. 3 Supplying and spraying chemical emulsion in sealed containers including delivery asspecified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20% including drilling 4 Providing and laying in position cement concrete of specified gradeexcluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived fromnatural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources) 5 Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) including shuttering of any structure upto level 3 6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Cold twisted bars 7 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) 8 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level inall shapes and sizes in :Cement mortar 1:6 (1 cement: 6 coarse sand) 9 Half brick masonry with common burnt clay F.P.S. (non modular) bricksof class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand) 10 Providing and fixing plywood 4 mm thick,non decorative veneerconforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with : Decorative veneer facings of approved manufacture (Duro/Kit ply/Green ply) 11 Providing and fixing 1st quality ceramic glazed wall tiles conforming toIS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of anysize as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarsesand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.Including dismentling existing if any. Make Kajaria/Nitco/Johnson 12 Providing wood work in frames of doors, windows, clerestory windowsand other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dashfastener shall be including. no seprate payment should be made).Kiln seasoned and chemically treated hollock wood . Wood frame should be painted wall side bitumestic paint. 13 Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of requiredsize with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.(Note: 100 mm Stainless steel Butt hinges and necessary screws shall be including in this ) Kiln seasoned and chemically treated hollock wood 35 mm thick shutters 14 Providing and fixing panelling or panelling and glazing in panelled orpanelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves orrebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.Ply wood 5 ply, 9 mm thick Decorative plywood non decorative veneer (Type - I) conforming to IS 1328 BWRtype(Make Duro/Kit ply/Green ply) 15 Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kgper sqm) fixing with ISi marked S.S. pressed butt hinges bright finished of required size with necessary screws.Kiln seasoned and chemically treated hollock wood 35 mm thick 16 Providing and fixing ISi marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 plyveneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISi marked Stainless Steel butt hinges with necessary screws(Make Duro/Kit ply/Green ply) 17 Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). 18 Providing and fixing wire gauge shutters using galvanized Stainless steel wire guage (Grade-304) aperture 1.4 mm and 0.50 mm, for doors, windows and clerestory windows with hingesand necessary screws :35 mm thick shutters With ISi marked stainless steel butt hinges of required size Kiln seasoned andchemically treated hollock wood 19 Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressedthree layer or graded plain wood particle board medium density grade I, ISi marked and conforming to IS : 3087 marked, including top coverof 6 mm commercial ply wood conforming to IS: 303 BWR grade, nickel plated M.S. pipe 20 mm dia ( heavy type) curtain rod with nickel platedbrackets, including fixing with 25x3 mm M.S. flat 10 cm long fixed to pelmet with hollock wood cleats of size 100 mm x 40 mm x 40 mm onboth inner side of pelmet and rawl plugs 75 mm long etc. all complete. 20 Providing and fixing stainless steel pipe curtain rods with bracket and finials and complete necessary items as per direction of Engg. In charge.25mm dia (heavy type) 21 Providing 40x5 mm flat iron hold fast 400 mm long/ 12mm anchor bolt including fixing to framewith 12 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement: 3 coarsesand : 6 graded stone aggregate 20 mm nominal size). 22 Providing and fixing ISi marked S.S. pressed butt hinges bright finished with necessary screws etc. complete :100x58x1.90 mm 23 Providing and fixing oxidised Aluminium hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete 150 mm long 24 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.(MakeDoorset/ Everite/Indobrass/Sandhu) 25 Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. (Make Godrej/Grace/Harrison) 26 Providing and fixing stainless steel sliding door bolts,transparent or dyed to required colour or shade, with nuts and screws etc. complete :250x16 mm (Make Classic/Doorset/Indobrass or equivalent make) 27 Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyedto required colour or shade, with necessary screws etc. complete :250x10 mm(Make Classic/Doorset/Indobrass or equivalent make) 28 Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyedto required colour or shade, with necessary screws etc. complete :200x10 mm(Make Classic/Doorset/Indobrass or equivalent make) 29 Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyedto required colour or shade, with necessary screws etc. complete :150x10 mm(Make Classic/Doorset/Indobrass or equivalent make) 30 Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyedto required colour or shade, with necessary screws etc. complete :100x10 mm(Make Classic/Doorset/Indobrass or equivalent make) 31 Providing and fixing aluminium handles, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyedto required colour or shade, with necessary screws etc. complete : 125 mm(Make Classic/Doorset/Indobrass or equivalent make) 32 Providing and fixing aluminium handles, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyedto required colour or shade, with necessary screws etc. complete :100 mm(Make Classic/Doorset/Indobrass or equivalent make) 33 Providing and fixing aluminium hanging floor door stopper, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper(Make Classic/Doorset/Indobrass or equivalent make) 34 Providing and fixing aluminium casement stays, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.(Make Classic/Doorset/Indobrass or equivalent make) 35 Providing and fixing cupboard shutter with 19 mm thick one side decorative and other side balancing lamination factory pressed BWPgrade marine ply as per IS 710 of approved brand including 2 mm thick PVC edge banding tape with hot glue by edge bending machine etc. withauto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer-in-charge. (Payment of providing and fixing autoclosing hinges shall be paid separately)(Duro/Kit ply/Green ply/Action tesa or equivalent make) 36 Providing and fixing factory-made cupboard with 18 mm thick HDHMR board( Century/Green ply with acrylic finish) with both sides laminated (lamination should be glossy0.5mm thick ). All edges should be covered with 1.3 mm thick high gloss PVC edge bending tape. The tape should be fixed with hot melt glue and fixed with pressed machine. Each shutter should be fixed to the framework by hinges(Stainless steel Piano hinges/Butt hinges). All work as per the direction of the Engineer in charge. 37 Structural steel work riveted, bolted or welded (Angles/Hollow tubes/Grills)in built up sections, trussesand framed work, including cutting, hoisting, fixing in position and applyinga priming coat of approved steel primer all complete. 38 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, includingcement slurry, including the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate 39 Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.18 mm thick 40 Providing and fixing glass /Aluminium strips in joints of terrazo/ cement concrete floors. 40 mm wide and 4 mm thick 41 Precast terrazo tiles 22 mm thick with graded marble chips of size upto 12 mm, laid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement:4 coarse sand):Medium shade pigment using 50% white cement and 50%ordinary cement including existing dismentling if any. 42 Kota stone slab flooring over 20 mm (average) thick base laid over andjointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cementmortar 1 : 4 (1 cement: 4 coarse sand) : 25 mm thick including existing dismentling if any. 43 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conformingto IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.Make Kajaria/Nitco/Johnson 44 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishingwith cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chaseincluding existing dismentling if any. 45 Providing & fixing polycarbonate sheetroofing up to any pitch, including fixing with polymer coated J or L hooks, bolts& nuts 8 mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc.The sheets shall be opaqueor translucent, clear or pigmented, textured or smooth as specified.2 mm thick flat (Make Durotuff or equivalent) 46 12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) 47 15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 fine sand) 48 Neat cement punning. Including providing and mixing Dr. Fixit 101 Pidiproof LW+ chemical as per direction Engg. In charge. 49 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer( Jk wall putty/Birla wall care putty/Asian or equivalent make), over the plastered wall surfaceper bag of 50kg ofcement 78.35 to prepare the surface even and smooth complete.as per direction Engg. In charge. 50 Distempering with 1st quality acrylic distemper( Narolac paint/Dulux/Asian) (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre as per direction Engg. In charge. 51 Applying priming coats with primer of approved brand and manufacture,having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface havingVOC content less than 50 grams/litre as per direction Engg. In charge.( Narolac paint/Dulux/Asian or equivalent make) 52 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)( Narolac paint/Dulux paint/Asian paintmake) 53 Wall painting with acrylic emulsion paint ofNarolac paint/Dulux paint/Asian paint having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coats 54 Painting with synthetic enamel paint of Narolac paint/Dulux paint/Asian paintof required colour to give an even shade including wood primer with putty :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture 55 White washing with lime to give an even shade :Old work (two or more coats) 56 Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and manufacturer including applying additional coats wherever required to achieve even shade and colour Old work (one or more coats) Narolac paint/Dulux paint/Asian paint make including repair with putty /POP 0.50sqm area asper direction og Engg. in charge. 57 Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 58 Painting with synthetic enamel paint of Narolac paint/Dulux paint/Asian paintof required colour to give an even shade :Two or more coats on old work 59 Finishing walls with Acrylic Smooth exterior paint of required shade :Old work (Two or more coat applied @ 0.90 ltr/10 sqm).Narolac paint/Dulux paint/Asian paint make including repair with putty /POP 0.50sqm area asper direction og Engg. in charge. 60 Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.With cement mortar 1:4 (1 cement : 4 fine sand) 61 Renewing glass panes, with wooden fillets wherever necessary: Float glass panes of nominal thickness 4 mm (weight not lessthan 10kg/sqm) 62 Supplying and fixing new wooden fillets wherever necessary:Hollock wood fillets 63 Raking out joints in lime or cement mortar and preparing the surface for re-pointing or replastering, including disposal of rubbish to the dumping ground,including Making chases up to 7.5x7.5 cm in walls including making good andfinishing with matching surface after housing G.I. pipe etc.all complete as per direction of Engineer-in-Charge. 64 Flush pointing with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement for flat tile bricks on top of mud phaska :With F.P.S. brick tilesIncluding Providing and mixing Dr. Fixit 101 Pidiproof LW+ chemical as per direction Engg. In charge. 65 Cleaning of chocked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. Dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 PSI for sewer line from 150 mm dia upto 300 mm 66 Demolishing cement concrete manually/ by mechanical means including disposal of material within CSIO as per direction of Engineer - in - charge.Nominal concrete 1:3:6 or richer mix (including equivalentdesign mix) 67 Demolishing cement concrete manually/ by mechanical means including disposal of material within CSIO as per direction of Engineer - in - charge.Nominal concrete 1:4:8 or leaner mix (including equivalentdesign mix) 68 Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work including disposal of material within CSIO(Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer-in-charge. 69 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within CSIO as per direction of Engineer-in-charge.In cement mortar 70 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within CSIO : Of area 3 sq. metres and below 71 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within CSIO : Of area beyond 3 sq. Metres 72 Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within CSIO as per direction of Engineer-in-charge :15 mm to 40 mm nominal bore 73 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within CSIO. 74 Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond CSIO initial lead, for all leads including all lifts involved. 75 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete.Including cement slurry punning wherever required. 76 Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, includingflush pipe,C.I. 100mm dia bend and dismentling existing p trap with cement jointwith manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid Hindware/Parry ware/Cera make or equivalent including dismentling the existing EWC/ orrisa pattern and WC flushing cistern. 77 Providing and fixing white vitreous china water closet squatting pan (Indian type) :Orissa pattern W.C. pan of size 580x440 mm Make Hindware/Parry ware /Cera or equivalent including dismentling the existing EWC/ orrisa pattern and WC flushing cistern. 78 Providing and fixing white vitreous china pedestal type (European type/ wash down type) water closet pan.Make Hindware/Parry ware /Cera or equivalent including dismentling the existing EWC. 79 Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. 80 Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including flush pipe. 10 litre capacity - White (Make Hindware/Parry ware /Cera or equivalent) 81 Providing and fixing solid plastic seat with lid for pedestal type W.C. pancomplete :White solid plastic seat with lid including dismentling existing ( Make Hindware/Parry ware /Cera or equivalent 82 Providing and fixing 100 mm CP grating for trap. Make Chilly/Prayag. 83 Providing and fixing soil, waste and vent pipes : 100 mm dia Sand cast iron S&S pipe as per IS: 1729 (SIRF/NICO/BIC/NIF or Equivalent make) 84 Providing and fixing soil, waste and vent pipes :75 mm diameter :Sand cast iron S&S pipe as per IS: 1729 85 Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : 75 mm dia pipe 86 Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : 100 mm dia pipe 87 Providing and fixing plain bend of required degree. 100 mm diaSand cast iron S&S as per IS - 1729 (SIRF/NICO/BIC/NIF or Equivalent make) 88 Providing and fixing plain bend of required degree.75 mm dia Sand cast iron S&S as per IS -1729 (SIRF/NICO/BIC/NIF or Equivalent make) 89 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 100 mm outlet Sand Cast Iron S&S as per IS: 1729 (SIRF/NICO/BIC/NIF or Equivalent make) 90 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 75 mm outlet Sand Cast Iron S&S as per IS- 1729 (SIRF/NICO/BIC/NIF or Equivalent make) 91 Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, including making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :15 mm dia nominal bore(Tata/Jindal Hissar make) 92 Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, including making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :20 mm dia nominal bore (Tata/Jindal Hissar make) 93 Cutting holes up to 30x30 cm in walls including making good the same:With common burnt clay F.P.S. (non modular) bricks 94 Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. 95 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore ( Cera /Hindware/ ESS ESS/ Prayag or Equivalent make) 96 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115 mm nominal bore ( Cera /Hindware/ ESS ESS/ Prayag or Equivalent make) 97 Cleaning of terrace/loft water storage tank (inside surface area) upto 2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of tank including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba all complete as per direction of Engineer- in-Charge. (The old date already written on tank should be removed with paint remover or black paint and if date is not written with the stencil or old date is not removed deduction will be made @ Rs. 0.10 per litre) (if during cleaning any GI fittings or ball cock is damaged that is to be repaired by contractor at his own cost and nothing extra will be paid on this account) 98 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: :Flat back wash basin of size 550x400 mm (Cera/Hindware or Equivalent make) 99 Providing and fixing ISi marked oxidised M.S. single acting spring hinges with necessary screws etc. complete (Copper oxidised as per IS 1378)150 mm 100 Providing and fixing fly proof Stainless steel wire guage (Grade-304) aperture 1.4 mm and 0.50 mm to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. With second class teak wood beading 62X19 mm 101 Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. 102 Carrying out petty job ofcarpentary including with nessary tools,drill machine ,nails , screw,gitty etc . At different locations which can not be measurd as directed by engineer -in-charge . 103 Carrying out petty job ofmassonary workincluding with all type of repair with concrete and mortar complete with nessary tools,sand , aggregate ,cement etc for the work which can not be measured. 104 Carrying out petty job ofglazingwork with all necessary tools ,ladderssafety belt, excluding glass putty beading etcFor petty work at different locations which can not be mesured as directed by engineer -in- charge 105 Carrying out petty jobs of painting works including of letterng, OBD,synthetic enamel paint etc with all necessary tools ,brushes .safety belts ,ladder paint is provided by the the deparmentetcfor petty work at different locations which can not be mesured as direction by engineer -in -charge 106 Carrying out petty job of welding works with necessary tools welding set & rods etc for petty works at different location which can not be measured as per direction of engineer -in-charge . 107 Carrying out petty jobs of drainage work with all necessary tools ,roding setsafety belt safety shoes ,mask etc taking every care of safety for petty works at different location which can not be measured as dorection of engineer -in-charge. 108 Carrying out petty jobs of misc.petty works with all necessary tools ,rehri,kassi etc at different location which can not be measured as directed by engineer -in-charge 109 Carrying out petty jobs of plumbing works with all necessary tools like pipe wrench, drilling machine drill bits, thread ,gitty,safety belts ,ladder, thread die,hexa blade ,all plunmbing tools ,old cycle tubes etc for petty works at different locations which can not be measured as per direction of engineer -in-charge. 110 Carrying out petty jobs related to engineering drawing, auto CAD, MEASUREMENT, ESTIMATION, SITE SUPERVISION JOB CARD DAILY DETAIL AND DEPUTE AND DIRCT LABOUR AS PER JOBCARD DEMAND etc for petty works at different locations which can not be measured as per the direction of the engineer -in-charge. 111 Providing layer of reinforced with galvanisied steel wire fabric (75x 25mm/50x50mmsize of 10guage thick ) forming a vertical plate bonded to wall . Two plate on either side of wall shoul be connected by galvanized steel rods at spacing of about 300 to 400mm . 112 Supplying and fixing aluminium strips( 22 gauge) thick and 650mm wide over the door with nail and other necesarymaterials 113 Providing excavator(JCB MACHINE) for cleaning of root of trees / buses / vegetable by mechanical means (Hydraulic Excavator)/ manual means in including dressing of sides and ramming of bottoms, including getting out the excavated soil and disposal of surplus excavated soil as directed, within CSIO . All kinds of soil. 114 Painting with damp-proof coating fiber-reinforced elastomeric liquid applied water proofing membrane paint of approved brand and manufacture to give an even shade two coat with one coat of self primer make Asian/Dulux/Nerolac as directed by Engg. In charge. 115 Finishing walls/Roofwith Damp Proof Paint with additives of required shade (Two coats ). including priming coat of one coat ofprimer appliedMake :- Asian Damp Proof paint or Equivalent
