SPECIAL REPAIRS TO BLDG NOP-545AT CDM SECUNDERABAD UNDER GE (NORTH) SECUNDERABAD.; 1 Demolition of cement concrete in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work otherwise specifically provided for roof treatment complete all as specifiedand directed. 2 M & L for 25 mm thick PCC (1:2:4) Type B0 by using 12.50mm graded stone aggregate as in roof where require over slabs and finishing the exposed surfaces fair even without using extra cement complete all as specified and directed 3 M & L for water proof plastering 10mm thick on fair faces of brick work or concrete or roof terrace surfacesin CM 1:3 with WPC @3% by weight of cement including finishing the surfaces all as specified and directed. 4 Supply only Integral waterproofing compound for waterproof plastering complete all as specifiedand directed. 5 M & L for priming the plastered roof surfaces with bituminous primer @ 0.3 Kg/Sqm and laying the APPmodified water proofing membrane as perIS 16540-2017/ IS 16532-2017mineral finish, 3 mm thick and weighing not less than 3.8 kg/sqmreinforced with non woven polyester /HMHDPE matt black finished over compatible primer/bonding bitumen with 100 mm overlap after necessarypreparation of surface complete as per manufacturer’s instructions with bituminous aluminium paint on top @ 0.1ltr/Sqm.complete all as specified. 6 M & L for water proof plastering 15mm thick on fair faces of brick work or concrete surfaces in wall/chajja or sunken floor in CM 1:3 with WPC @3% by weight of cement including finishing the surfaces even and smooth without using extra cementall as specified and directed. 7 M & L for Rendering 5mm thick on brick work or concrete ceiling surfaces in cement mortar 1:3 including finishing the surfaces all as specified and directed. 8 M & L for Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:6 all as specified and directed. 9 Demolotion of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed 10 M & L for brick work with fly ash bricks straight or curved on plan exceeding 6 metre mean radius with old size bricks built in CM 1:6 complete all as specified and as directed. 11 Dismantling of floor, hearth or wall tilesincluding cement mortar bedding (but not backing),removal servicable tiles to store and rubbish off the premises, all as specified and directed. 12 S & F Glazed ceramic coloured wall tiles in vertical surface 300mmx600mmx 7 to 8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles over and including 10 mmthick rendering in CM 1:3 all as specified and directed. 13 M & L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) coloured area of Each tile size 400mmx400mm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mmthick screed bed in CM 1:4 all as specified and directed. 14 M & L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile 600mmx600mm, in floors etc. set and jointed in neat cement slurry and pointed incoloured cement to match the tiles over and including 15 mmthick screed bed in CM 1:4 all as specified and directed. 15 S & F Vitrified Ceramic tiles Dark shade 10 mm thick (square/ rectangular) polished, area of Each tiles sizes exceeding 0.42 Sqm but not exceeding 1.00 Sqm, in skirting/daddo etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles over and including 10 mmthick rendering in CM 1:3 all as specified and directed. 16 S & F Vitrified Ceramic tiles Dark shade double charged 10 mm thick (square/ rectangular) matt finished, area of Each tilessize not exceeding 0.36Sqmin floors/landings/tread etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles over and including 15 mmthick screed bed in CM 1:4 all as specified and directed. 17 S & F Vitrified Ceramic tiles Dark shade 10 mm thick (square/ rectangular) matt finished, area of Each tiles size not exceeding 0.36Sqm, in skirting/daddo/riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles over and including 10 mmthick rendering in CM 1:3 all as specified and directed. 18 M & L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 15 mmthick screed bed in CM 1:4 complete all as specified and directed. 19 M & L for Kota stone slab 20-25mm thick in skirting/dadoand including 10 mmthick rendering in CM 1:3 complete all as specified and as directed 20 Demolition Stone slabs and tiles/granite tiles laid in cement mortar of any description or thickness in floors, aprons etc. 21 M & L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platfoRms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over cement screed 15mm thick incm 1;4 over complete all as specified and directed. 22 Taking down chowkhats or frames with shutters (w/o taking off shutters from the frames) n exc 1.5 SqmEach etc including making good of hold fast holes with PCC Type C 1:3:6 complete all as directed. 23 Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) exc 1.5 but n.exc 4Sqm Each etcmaking good of hold fast holes with PCC Type C 1:3:6 complete all as directed. 24 Taking down chowkats or frames with shutters of any description area exc1 Sqm but not exc 2 Sqm and refixing in same opening including easying adjusting and refixing builders hardware as required including renewal of unserviceable screws, welding etc., complete all as specified and directed. 25 S & F 12mm thickness toughened glass factory made frosted with CDM logo embedded as in door /wall partitionincluding providingand fixing oftop & bottom pivot & spring typefixing arrangements& necessary holes & making good & required hinges,SS 304 grade handles,door/floor spring etc and including all necesaary fittings complete all as specified. 26 S & F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed. 27 S & F 450mm long stainless steel handle as in glass doors complete all as specified and directed. 28 S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions.Note: Unit price quoted would be inclusive M&L for necessary scaffolding, ladders etc. inorder to work at higher heights. 29 S & F factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 Sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll foRming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction. (Glass shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 30 S & F 4 mm thick tinted sheet glass frosted, ordinary quality and glazing with oil putty in square Nexc 0.5 sq. m in Each pane complete all as specified and directed. 31 S & F 5.5 mm thick tinted sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in Each pane complete all as specified and directed. 32 S & FStainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staplescomplete all as specified and directed. 33 S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/Cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being teRmite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately)Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable.Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified. 34 S & FProviding and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg/Cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being teRmite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately). 35 S & F of 35mm thick IInd class hard wood glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc. divided in to square with plain chamfered or rounded mitred and rebated sash bars, any numbers, edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc, size of members of shutters as per ISI and all as specified in SSR Pt –I and as directed. 36 M & L preparation of surfaces of wood and wood based material description over 10cm in width or girth applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified. 37 S & F 125 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-22 complete all as specified and as directed 38 S & F 200 mm long Aluminium anodised, barrel tower bolts of extruded section and fixed 39 S & F 150mm Extruded aluminium alloy handles, fabricated type, anodised all as specified. 40 M & L for 140 mm long floor doorstopper brass body and tonguewith hard drawn steel spring fixed complete all as directed 41 S & F 200 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed as specified and directed 42 S & F in repair Aluminium Door closerhydraulically regulated designation No.3,universal type ,suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg. complete all as specified and directed 43 S & F in repair 12 mm thick Ply wood BWR, type BB fixed with screws to walls by inserting rawl plugs in the wall/ column surfaces. 44 M & L for 0.9 mm thick colour/ white laminated sheet fixed to wooden surface with glue complete all as specified and directed. 45 S & F 100mm size hasp and staple, safety type, aluminum anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws, 46 S & F40mm dia cupboard knobs fixed with nut screw & washer or brass polished. 47 S & F ball catch spring 8mm dia steel ball and brass body and striking plate including letting in complete 48 S & F in repairs drapery curtain rod of stainless steel 25mm dia complete with stainless steel brackets and side caps fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified and directed. 49 S & Fin repairShelves made of HDHMR (high density high moisture resistance) board manufactured with hard wood, prelaminated both sides white in colour 18 mm thick water resistant, teRmite resistant, duly edge banded with PVC taping 0.8 mm thick, cut to shape & size of shelves including dismantling board complete all as specified and directed. 50 S & F for 300 mm MS ordinary rat tail rod pattern springs and including roller and roller plate complete 51 M & L for M.S Hold fasts of FI 25 x 3 mm complete all as specified and directed. 52 S & F in repair vitreous china counter top WHB white of size 565x415x190mm or required size as approved and complete all as specified and as directed.Make:cat no: FLS-WHT-5601 of Jaquar or equivalent in ROCA/KOHLER 53 S & F in repair vitreous china wash hand basin white of bowl size 550mm x 440mm including waste coupling and PVC waste pipe 32mm dia,pillar tap cast copper alloy with capstan heads chromium plated fancy type for 15 mm bore pipe, including M S brackets complete all as specified and directed. 54 Taking out existing water closet, pedestal pattern and replacing with new EWC (Pedestal Pattern) cascade type withflush tank, seat cover etc white including fixing bolts complete including making good to floor to match with adjoining surfaces.Make:cat no: SLS-WHT-6851S220PP Jaquar or equivalent in ROCA/KOHLERas approved. 55 Taking out existing water closet, pedestal pattern and replacing with new EWC (Pedestal Pattern) cascade type withflush tank, seat cover etc white including fixing bolts complete including making good to floor to match with adjoining surfaces. 56 S & F in repair Vitreous china Urinal, Half stall type, white withwaste pipe and CP brass spreader complete including providing andfixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plug with and including 60mm long brass screws, pointing around urinal back in cement;flush pipe, grating and union for discharge pipe including CP Urinal spreader for fixing with 15 mm dia pipe complete all as specified and directed. Make: Cat Part No: URS-WHT-13253N of Jaquar or equivalent in ROCA/KOHLER 57 S&F Urinal partitions with touhhened frosted glass slabs terminating about 40cm above floor line, fixed in repairs complete all as specified and directed. 58 S&F in repair Vitreous china Urinal, Half stall type, white withwaste pipe and CP brass spreader complete including providing andfixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plug with and including 60mm long brass screws, pointing around urinal back in cement;flush pipe, grating and union for discharge pipe including CP Urinal spreader for fixing with 15 mm dia pipe complete all as specified and directed. 59 S & F in repair vitreous china urinal partition white of size 310x700 mm. terminating about 40cm above floor line complete all as specified and as directed 60 S & F in repairwall hung fancy type bevelledframeless looking mirror of 5mm thick size1.50mx1.20m/1.8mx1.0m or of suitablesize with quality glass with SS Studsfixed to wallwith chromium plated screws and cup washer all as specified & directed 61 M & L in repair600 X 450 mm bevelled edge mirror of selected quality glass , mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. 62 S & F in repairs Stop/angle valves fancy type 15mm dia, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed. Make : Cat No: FUS-CHR-29053 of Jaquar or equivalent in ROCA/KOHLER . 63 S & F in repairs angle cock quarter turnwith flange chromium plated cast copper alloy screwed down complete all as specified and directed.Make: Johnson Eco Cat part No: T3910C or equivalent in Cera/Parryware/Hindware as approved by GE. 64 S & F in repair CP health faucet with 01 Mtr tube and hook complete all as specified .Make : Cat No: ALD-CHR-573 of Jaquar or equivalent in ROCA/KOHLER . 65 S & F in repairs 15mm size two way bib tap fancy type chromium plated, crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all asspecified and directed .Make: cat no: FUS CHR 29041of Jaquar or equivalent in ROCA/KOHLERas approved. 66 S&F in repairs Two Way (2 in 1) bib taps with wall flange quarter turn suitable for 15mm bore pipe fancy type brass CP, screwed for iron pipe or brass ferrule complete all as specified and directed.Make: JohnsonVIVA series Cat part No: T4808C or equivalent in Cera/Parryware/Hindware as approved by GE 67 S & F in repairs Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed 68 S & F in repairs 15 mm bore Fancy type pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all asspecified and directed Make: Cat No. FUS-CHR-29021 of Jaquar or equivalent in ROCA/KOHLER as approved. 69 S & F in repairs Pillartap quarter turn suitable for 15mm bore pipe fancy type brass CP screwed for iron pipe or brass ferrulecomplete all as specified and directed.Make: JohnsonVIVA series Cat part No: T4801C or equivalent in Cera/Parryware/Hindware as approved by GE 70 S & F in repairs, wall mixer with provision of over head shower with 115mm long bend pipe on upper side connecting legs and wall flanges complete all as specified and directed.Make :- Cat No FLR-CHR-5273UPR of Jaquar or equivalent in ROCA/KOHLER. 71 S & F in repairs brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges 72 S & F in repairs Soap dish, vitreous China white, approximate size 160x 160x90mm embedded in the wall 73 S & F in repairs bib tap fancy type chromium plated, crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all asspecified and directed Make : Cat No. FUS-CHR-29037 of Jaquar or equivalent in ROCA/KOHLER make as approved 74 S & F in repairs Bib cock long nose quarter turn suitable for 15mm bore pipe with flange fancy type brass CP with screwed for iron pipe or brass ferrulecomplete all as specified and directed. Make: JohnsonVIVA series Cat part No. T4806Cor equivalent in Cera/Parryware/Hindware as approved . 75 S & F sheet glass shelf assembly consisting of 5.50mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing fixed in repairs complete all as specified and directed 76 S & F in repairs Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms)complete all asspecified and directed 77 S & F PVC (SWR) floor trap 75mm dia, plain withSS grating including jointing with solvent cement complete all as specified. 78 S & F in repairs Grating doom 100mm dia of PTMT/ SS. (Minimum weight 85gms) complete all as specified. 79 S & F in repairs PVC connections 15 mm size with PTMT nuts of length 600 mm complete all asspecified and directed 80 S & F in repairsPVC LDPE waste pipe 32mm dia 1m lengthcomplete all asspecified and directed 81 S & F in repairs Rotational moulded polyethylenewater storage tank 3 layer white colour water tank , non- toxic effect, algae foRmation protection (made from Virgin grade of polyethylene material which is duly stabilized with anti-oxident Plastic) of capacity 500 litres, (cylindrical vertical one piece moulded with closed top), the internal and external surfaces of tanks are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S & F necessary GI/CPVC fittings, inlet/outlet washout, overflow pieces long nipples, check nuts & washer, 20 mm diaball valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball (Minimum weight 210gms) and high pressure with crutch or butterfly handle etc complete including dismantling existing water tank complete all as specified and directed. 82 S & F in repairs Rotational moulded polyethylenewater storage tank 3 layer white colour water tank , non- toxic effect, algae foRmation protection (made from Virgin grade of polyethylene material which is duly stabilized with anti-oxident Plastic) of capacity 1000 litres, (cylindrical vertical one piece moulded with closed top), the internal and external surfaces of tanks are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S & F necessary GI/CPVC fittings, inlet/outlet washout, overflow pieces long nipples, check nuts & washer, 20 mm diaball valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball (Minimum weight 210gms) and high pressure with crutch or butterfly handle etc complete including dismantling existing water tank complete all as specified and directed. 83 S & F 16 mm CPVC pipes SDR 11& Plain CPVC SDR 11fittings in trenches complete all as specified. 84 S & F 20 mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified. 85 S & F 25 mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified. 86 Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store 87 Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store 88 Taking up or down 25 mm bore steel tubing and connections, including cleaning for refixing or removal to store 89 S & F in repairs PVC (SWR) P trap 110mm dia complete all as specified. 90 S & F in repairs PVC (SWR) door Bend 150mm dia complete all as specified 91 S & F in repairs PVC (SWR) door Bend 110mm dia complete all as specified 92 S & F in repairs PVC (SWR) door Bend 75mm dia complete all as specified 93 S & F in repairs PVC (SWR) single T 75mm dia complete all as specified. 94 S & F in repairs PVC (SWR) single T 110 mm dia complete all as specified 95 S & F in repairs PVC (SWR) pipes 110mm bore double socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed 96 S & FPVC (SWR) pipes 110mm bore double socketed, in any length with rubber ring joints, fixedon walls complete all as specified and directed 97 S & F in repairs PVC (SWR) pipes 110mm bore double socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed 98 Cutting chases, pinning in, in brick wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring etc. and making good, in cement mortor 1:3 cutting not exceeding 10cm girth complete all as specified and directed. 99 S & F in repairs PVC (SWR) pipes 75mm bore double socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed 100 S & FPVC (SWR) pipes 75mm bore double socketed, in any length with rubber ring joints, fixedon walls complete all as specified and directed 101 Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixingor removal to Store (measured overall as fixed along the centre line over fittings and accessories) 102 M & L for preparartion of new wall surfaces & applyingtwo coat of Plastic emulsion over a coat of a primer over 3mm thick wall care putty in two layer complete all as directed. 103 M & L for preparartion of new ceiling surfaces & applying two coats of Plastic emulsion over a coat of primer including 3mm thick wall care putty in two layers complete all as specified and directed. 104 M & L for preparation of newly plastered external wall & concrete surfaces &applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ XSqm over Two coat of putty 3mm and including priming coat of exterior primer applied @ 0.90 litre/ XSqm over wall/concrete surfaces of any height complete all as directed. 105 M & L for Complete removal of existing treatment of external wall surfaces &applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ XSqm over Two coat of putty 3mm and including priming coat of exterior primer applied @ 0.90 litre/ XSqm over wall/concrete surfaces of any height complete all as directed. 106 M & L Complete removal of existing treatmentof old plastered internal surfaces of wall and applying two coats of Platic emulsion paint over a coat of primer including 3mm thick wall care putty in two layers complete all as specified and directed.. 107 M & L Complete removal of existing treatmentof old plastered ceiling surfaces and applying two coats of Plastic emulsion paint over a coat of primer including 3mm thick wall care putty in two layers complete all as specified and directed.. 108 M & L for Preparing old steel surfaces of any description exc 10cm width or grith and applying one coat of synthetic enamel paintcomplete all as specified and directed. 109 M & L for Preparing old wooden surfaces of any description exc 10cm width or grith and applying one coat of synthetic enamel paintcomplete all as specified and directed. 110 M & L for 3mm thick wallcrack putty on old wall /concrete surfacesall as specified and directed. 111 M & L Precast reinforced cement concrete type B1 (1:2:4) using 20 mm graded aggregate set in CM(1:4) in landings for WHB , cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces . 112 S & F for Mild steel TMT bars8mm dia, and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality. 113 Dismantling of Asbestos cement (corrugated, semi-corrugated, etc. ) sheets in roof coverings . 114 S&F Pre-painted galvatume aluminium zince coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified 115 Dismantling of fillets, rails, posts, rafters, purlins, etc. under 40 sq.cm in section. 116 S & F rolled section as in main and cross beams, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connected plates confirming to Fe-410-W.Gde E-250 ,Quality A 117 M & L preparation ofnew steel surfaces of any description, over 10 cm in width or girth, not otherwise described, applying two cots of eynthetic enamel paint over red oxide, zinc chrome primer complete all as specified and as directed. 118 Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets all as completed. 119 S & F GI frame work Size of gnd 605 x 605mm for seamless celling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centrelintermediate channel 0 9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including coiling section (not exc 12 m length) of 0.55 mm thickness having kurfed web of 50 mm and fiange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre and Hangers 6 mm dia G. (upto 1200mm length) adjusting level fixed to root stabs by means of ceiling cleats made out of G1 flat 40 x 3 mm size 60mm long and expansion hold fasteners 12 5mm dia, 40mm long complete all as specified.Note: Unit rate quoted shall include for necessary scaffolding, trestlers, ladders & cradlers required for execution of work 120 M & L for Providing and fixing 12mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G1 wire mesh (Fillets, metal frame work and GI wire mesh paid separately) with specified shape and architectural elevation complete all as specified an directed by Engineer in Charge.Note: Unit rate quoted shall include for necessary scaffolding, trestlers, ladders & cradlers required for execution of work 121 M & L for preparation of new gypsum board ceiling surfaces & applying two coat of Plastic emulsion paint over a coat of alkali resistant primer over plaster of pans putty of 2 mm thickness on ceiling surface complete all as specified.Note: Unit rate quoted shall include for necessary scaffolding, trestlers, ladders & cradlers required for execution of work 122 M & L for Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete all as specified and as directed 123 S & F in repairs standard wall mount stainless steel hand sink features a countertop edge with an offset to guard against drips and overflow, 1.00mm thick for kitchen or laboratory, with plug, wastepipe, washers, including cantilever castiron brackets, connecting union etc., overall size 2.3m X 0.45m with bowl size 2.0m X 0.35m X 0.4m complete all as specified and as directed.Note: Effective/clear dimensions of sink can be varried by ±5% with prior approval. 124 Taking down existing unserviceable point wiring of any description/type/ size of light/ fan/tube/power/two way/bell point etc on TW batten/conduit includingremovalof batten / conduit / gutties / wooden boards / switches / sockets / regulators/ light fittings etc and removal of unserviceable material out of site and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes all as specified. 125 Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as per existing at site including making good the disturbed surfaces to match with the existing finishes all as specified. 126 Taking down carefully by unscrewing from boards/ outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators, etc. for reuse at site complete all as specified and directed. 127 M & L for Point wiring on concealed conduit with 1.5 Sq mm FRLS copper conductor single core PVC insulated sheathed 1100 V multistranded drawn through including rigid PVC conduit and conduit of dia medium grade and modular accessories including fixing/grouting sunken/ surface along with modular flush box of sutiable thickness covered with suitable modular cover plate including running up of 1.5 Sq mm FRLS copper conductor PVC insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly for fixing the switches/ sockets/ regulators etc all as specified for : NOTE: Rate of Modular Flush box and Cover plate are inclusive of rate quoted by the contractor 128 (a) One light/fan/Bell point controlled by one, one way switch 10 A, SP 129 All as per SL No 127 above but One 2/3 pin 5 Amps switch socket outlet point controlled by one switch on the same board. 130 All as per SL No 127 above but One 3 Pin 5 Amps switch socket Independt board. 131 Description all as per item No 127 here-in-before but using 2.5 Sq mm FRLS single core copper conductor cable of multistranded PVC insulated unsheathed 1100 Volts grade for 5/15 Amps switch socket combination point including running of 2.5 Sq mm FRLS copper conductor PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly. 132 S & F Modular switch 1 way 10 A, 1 Module capacity 230 volts. 133 S & F Modular switch 1 way 16 A, 1 Module capacity 230 volts. 134 S&F Modular Bell Push 6A, 1 Module. 135 Supply and fix socket outlet modular type multipurpose 2/3 Pin, 10 amps, 230 volts combined 2 Module complete all as specified & directed. 136 Supply and fix socket outlet modular type multipurpose 2/3 Pin, 6/16 amps, 230 volts combined 2 Module complete all as specified & directed. 137 S & F Modular ceiling fan regulator stepped type heavy duty suitable to work on 230 volts, 2 Module complete all as specified & directed. 138 S & F calling Bell, AC, 230 volts, single polecomplete all as specified & directed 139 S & F ceiling rose three terminal surface bakelite type AC 50 Hz 230 Volts of size 65 x 50 mm complete all as specified. 140 S & F in replacement of Single pole and Neutral enclosure with a three pin and earth plug and socket metal clad complete with one singlepole MCB 20 Amps (AC Box) all as specified and directed. 141 S & F in replacement of Triple pole and Neutral enclosure with a two pin and earth plug and socket metal clad complete with one singlepole MCB 32 Amps (AC Box) all as specified and directed. 142 S&F in replacement sheet metal enclosure vertical type MCCB DB TPN 6 way double door having degree of protection IP 43-IK 09 with metal double door, 415 Volts, flush type made out of 1.2 mm thick thick CRCA sheet, metal duly powder coated and confirming to IS 8623 with suitable rated copper bus bar with neutral linkwith suitable rated bus bar 415 volts with ncluding 200 Amps MCCB 25 KA as incomer and 01 Nos outgoing TP MCBs of 63 Amps and 15 Nos outgoing SP MCBs withincluding provision for MCCB TPN as incomer and SP/TP MCBs as outgoing and total number of modules equal to MCCB TPN + 18 with blanking plates and fixed flush to wall and making good the disturbed surfaces etc, with magnetic locking system complete all as specified.Note : MCB SP/TPs shall be measured and paid seperately. 143 S&F in replacement sheet metal enclosure vertical type MCCB DB TPN 6 way double door having degree of protection IP 43-IK 09 with metal double door, 415 Volts, flush type made out of 1.2 mm thick thick CRCA sheet, metal duly powder coated and confirming to IS 8623 with suitable rated copper bus bar with neutral linkwith suitable rated bus bar 415 voltsincluding 200 Amps MCCB 25 KA as incomer and 06 Nos outgoing TP MCBs of 63 Amps with suitable rated copper bus bar with neutral link including provision for MCCB TPN as incomer and SP/TP MCBs as outgoing and total number of modules equal to MCCB TPN + 18 with blanking plates and fixed flush to wall and making good the disturbed surfaces etc, with magnetic locking system complete all as specified. Note : MCB SP/TPs shall be measured and paid seperately. 144 S&F in replacement sheet metal enclosure vertical type MCCB DB TPN 4 way double door having degree of protection IP 43-IK 09 with metal double door, 415 Volts, flush type made out of 1.2 mm thick thick CRCA sheet, metal duly powder coated and confirming to IS 8623 with suitable rated copper bus bar with neutral link with suitable rated bus bar 415 voltsincluding including 100 Amps MCCB 25 KA as incomer and 02 Nos outgoing TP MCBs of 63 Amps and 06 Nos outgoing SP MCBs including provision for MCCB TPN as incomer and SP/TP MCBs as outgoing and total number of modules equal to MCCB TPN + 12 with blanking plates and fixed flush to wall and making good the disturbed surfaces etc, with magnetic locking system complete all as specified. Note : MCB SP/TPs shall be measured and paid seperately. 145 S&F in replacement sheet metal enclosure vertical type MCCB DB TPN 4 way double door having degree of protection IP 43-IK 09 with metal double door, 415 Volts, flush type made out of 1.2 mm thick thick CRCA sheet, metal duly powder coated and confirming to IS 8623 with suitable rated copper bus bar with neutral link with suitable rated bus bar 415 voltsincluding including 100 Amps MCCB 25 KA as incomer and 01 Nos outgoing TP MCBs of 63 Amps and 09 Nos outgoing SP MCBs including provision for MCCB TPN as incomer and SP/TP MCBs as outgoing and total number of modules equal to MCCB TPN + 12 with blanking plates and fixed flush to wall and making good the disturbed surfaces etc, with magnetic locking system complete all as specified.Note : MCB SP/TPs shall be measured and paid seperately. 146 Supply, fix, connecting in replacement and testing factory made, distribution board, (MCB DB) TPN, 4 Way, having degree of protection IP 43-IK 09 with metal double door, 415 Volts, flush type made out of 1.2 mm thick thick CRCA sheet, metal duly powder coated and confirming to IS 8623 with suitable rated copper bus bar with neutral link including provision for MCB TPN as incomer and SP MCBs as outgoing and total number of modules equal to MCB TPN + 12 with blanking plates and fixed flush to wall and making good the disturbed surfaces etc, complete all ass specified and as directed. Note: MCB TPN and MCB SP will be measured and paid seperately. 147 S&F in replacement sheet metal enclosure vertical type MCCB DB TPN 6 way double door having degree of protection IP 43-IK 09 with metal double door, 415 Volts, flush type made out of 1.2 mm thick thick CRCA sheet, metal duly powder coated and confirming to IS 8623 with suitable rated copper bus bar with neutral linkwith suitable rated bus bar 415 voltsincluding 250 Amps MCCB 25 KA as incomer and 03 Nos outgoing TP MCBs of 63 Amps and 09 Nos outgoing SP MCBs with suitable rated copper bus bar with neutral link including provision for MCCB TPN as incomer and SP/TP MCBs as outgoing and total number of modules equal to MCCB TPN + 18 with blanking plates and fixed flush to wall and making good the disturbed surfaces etc, with magnetic locking system complete all as specified. 148 Supply, fix, connecting in replacementand testing MCB, Triple Pole Neutral (TPN) 40 to 100 Amps, 415 Volts of rupturing capactiy 10 KA, C Seriescomplete all as specified and as directed. 149 Supply, fix, connecting in replacementand testing MCB, Triple Pole TP 25 to 63 Amps, 415 Volts of rupturing capactiy 10 KA, C Seriescomplete all as specified and as directed. 150 S and F in replacment of sheet metal enclosure MCBDB SPN 12 way with suitable rated bus bar 240 Volts double door with magnetic locking system complete all as specified. 151 S and F in replacment of sheet metal enclosure MCBDB SPN 8 way with suitable rated bus bar 240 Volts double door with magnetic locking system complete all as specified. 152 S and F in replacement of sheet metal enclosure MCBDB SPN 6 way with suitable rated bus bar 240 Volts double door with magnetic locking system complete all as specified. 153 Supply, fix, connecting in replacement and testing MCB, Single Pole Neutral (SPN) 40/63 Amps, 415 Volts of rupturing capactiy 10 KA, C Series complete all as specified and as directed. 154 Supply, fix, connecting in replacement and testing MCB, Single Pole (SP), 6-32 Amps, 240 volts of rupturing capacity 10 KA, C series complete all as specified and as directed. 155 S & F in replacement Surface Modular Box of 6 way along with 6 way Modular plate and2 Nos of 16 Amps Switches and 6/16Amps multipurpose Sockets with connected internal wiring complete all as specified and directed by Engg in Charge. Note: Modular Plate, Switches & Sockets are inclusive of the rate quoted. Make: Indo Asian cat No. 800186,800166, 800103,800122 or equivalent make in Anchor Roma 156 M & L for Submain wiring with two single core 2.5 Sq mm FRLS PVC insulated copper conductor multistranded 1100 Volts grade drawn through andincluding rigidPVC conduit and concealed conduit accessories of suitable dia medium grade including running up of one runs of2.5 Sq mm FRLS copper conductor multistranded PVC insulated cable as earth continuity conductor along the wiring and connected to the common earth dolly completeincludingremovingtheexistingunserviceablesubmain wiringandmakinggood thedisturbed surfaceto match with the existing all as specified.Note:-two runs of cable, one run of earth contuinity conductor and one run of conduit shall bemeasured and paid as one unit length.NOTE: SUBMAIN WIRING SHALL BE REPLACED IN MAIN LOBBY OF OFFICER MESS WHICH IS AT HEIGHT IN THE RANGE UPTO 15 MTRS, COST OF SCAFFOLDING FOR RE-WIRING IF REQUIRED SHALL BE BORNE BY THE CONTRACTOR. 157 M & L for Submain wiring with two single core 4 Sq mm FRLS PVC insulated copper conductor multistranded 1100 Volts grade drawn through andincluding rigidPVC conduit and concealed conduit accessories of suitable dia medium grade including running up of one runs of4 Sq mm FRLS copper conductor multistranded PVC insulated cable as earth continuity conductor along the wiring and connected to the common earth dolly completeincludingremovingtheexistingunserviceablesubmain wiringandmakinggood thedisturbed surfaceto match with the existing all as specified.Note:-two runs of cable, one run of earth contuinity conductor and one run of conduit shall bemeasured and paid as one unit length. 158 M & L for Submain wiring with two single core 6 Sq mm FRLS PVC insulated copper conductor multistranded 1100 Volts grade drawn through andincluding rigidPVC conduit and concealed conduit accessories of suitable dia medium grade including running up of one runs of6 Sq mm FRLS copper conductor multistranded PVC insulated cable as earth continuity conductor along the wiring and connected to the common earth dolly completeincludingremovingtheexistingunserviceablesubmain wiringandmakinggood thedisturbed surfaceto match with the existing all as specified.Note:-two runs of cable, one run of earth contuinity conductor and one run of conduit shall bemeasured and paid as one unit length. 159 M & L for Submain wiring with four single core 6 Sq mm FRLS PVC insulated copper conductor multistranded 1100 Volts grade drawn through andincluding rigidPVC conduit and concealed conduit accessories of suitable dia medium grade including running up of one runs of6 Sq mm FRLS copper conductor multistranded PVC insulated cable as earth continuity conductor along the wiring and connected to the common earth dolly completeincludingremovingtheexistingunserviceablesubmain wiringandmakinggood thedisturbed surfaceto match with the existing all as specified.Note:-four runs of cable, one run of earth contuinity conductor and one run of conduit shall bemeasured and paid as one unit length. 160 M & L for Submain wiring with four single core 10 Sq mm FRLS PVC insulated copper conductor multistranded 1100 Volts grade drawn through andincluding rigidPVC conduit and concealed conduit accessories of suitable dia medium grade including running up of one runs of10 Sq mm FRLS copper conductor multistranded PVC insulated cable as earth continuity conductor along the wiring and connected to the common earth dolly completeincludingremovingtheexistingunserviceablesubmain wiringandmakinggood thedisturbed surfaceto match with the existing all as specified.Note:-four runs of cable, one run of earth contuinity conductor and one run of conduit shall bemeasured and paid as one unit length. 161 M & L for Submain wiring with two single core 10 Sq mm FRLS PVC insulated copper conductor multistranded 1100 Volts grade drawn through andincluding rigidPVC conduit and concealed conduit accessories of suitable dia medium grade including running up of one runs of10 Sq mm FRLS copper conductor multistranded PVC insulated cable as earth continuity conductor along the wiring and connected to the common earth dolly completeincludingremovingtheexistingunserviceablesubmain wiringandmakinggood thedisturbed surfaceto match with the existing all as specified.Note:-two runs of cable, one run of earth contuinity conductor and one run of conduit shall bemeasured and paid as one unit length. 162 Taking down ceiling fan/ exhaust fan, sealing cable end,dismantling blades, removing fan and shifting the all unserviceable ceiling fans/exhaust fans to MES store complete all as specified and directed. 163 Supply, fix, test and commissioning of Energy efficient ceiling fan with three blades, down rods andaccessories, 230V,1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE , Five star rated with brushless direct current motor (BLDC) fixed to roof/ceiling with suitable clamp including provisioning of flexbile copper cord of size 23/0.0076 of required length from ceiling rose or connector to ceiling fan etc., complete all as specified and as directed. 164 Supply, fix, test and commissioning of Exhaust fan, metal body, AC single phase, 230 V of size 450 mm sweep heavy duty, 4 blades, copper winding with louvers shutters connecting up with and including provision of PVC insulated copper flexible cord from ceiling rose to connection of exhaust fan complete all as specified. 165 Supply, fix, test and commissioning of Exhaust fan, metal body, AC single phase, 230 V of size 300mm sweep heavy duty, 4 blades, copper winding with louvers shutters connecting up onnecting up with and including provision of PVC insulated copper flexible cord from ceiling rose to connection of exhaust fan complete all as specified. complete all as specified and as directed. 166 Supply and Fixing Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, Voltage 230 V, 50 HZ, RPM 1200, Copper winding of 250mm sweepconnecting up with and including provision of PVC insulated copper flexible cord from ceiling rose to connection of exhaust fan complete all as specified. 167 Taking down the geysers of capacity 25/35 from its mounting position by removing all water and electric connections and de-assembling the geyser after carrying out the following works, (a)Descaling, cleaning the inner tank thoroughly and there should not be any bad taste of water.(b)Examining the water tightness of storage tank after cleaning.(c)Examining the physical condition of thermostat, base assembly fusible plug and outer tank for its serviceability.(d)Inspection of pilot lamps.(e)Reassembling the geyser parts and testing including checking all electrical system (ensuring there is no current leakage) and also conducting hydraulic testing.(f)Re-fixing the Geyser and making electric connections,inlet and outlet water connections and testing and checking of all water inlet, outlet valves connected with geysers.Note : Defective /worn outpartsif required shall be measured and paid separetely under relevant items in this schedule. 168 Supply and fix rubber PVC connection of 2/3 feet complete, all as specified and as directed. 169 Supply & fix MS base plate cup any type with screws of suitable size as per requirement complete, all as specified and as directed. 170 Supply & fix heating element of the 1/1.5 KW rating as required at site including rubber washers of any make and type complete as per sample, all as specified and as directed. 171 Supply & fix Steel inner tank of 25 litre capacity geyser tank by made out of steel sheets appropriate thickness complete, all as specified and as directed . 172 Supply & fix thermostat suitable for the geysers of 25 Liters capacities complete, all as specified and as directed. 173 Supply & fix auto cut suitable for the geysers of 25 Liters capacities complete, all as specified and as directed. 174 Supply & Replace Air Release Valve suitable for geyser 25/50 ltrs all as specified and directed. 175 Supply and Fix Rigid non-metallic PVC conduit 25mm inclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.complete all as specified and directed. 176 Supply and Fix Rigid non-metallic PVC conduit 20 mm inclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.complete all as specified and directed 177 Supply and Fix Rigid PVC Casing & Capping of 25 mm wide including all accessories required for drawing of 1.5/2.5 sqmm wire complete all as specified and directed 178 Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed. 179 S & F in replacement of wall mounted batten type LED light of 12 watts with aluminium extruded batten and system lumens of 1200 lm minimum with IP & surge protection alongwith driver efficiency >85% and power factor >0.95 , colour rendering index CRI>80 along with integrated driver completeand connecting to the point wiring with necessary flexible copper conductor of multistrand three core of suitable length from fitting to the ceiling roseall as directed.Make: Philips Model BN021 LED12S PSU GR or equivalent make in Havells/Wipro/GE. 180 S & F in replacement of wall mounted batten type LED light of 20/22 watts with aluminium extruded batten and system lumens of 2200 lm minimum with IP & surge protection alongwith driver efficiency >85% and power factor >0.95 , colour rendering index CRI>80 along with integrated driver completeand connecting to the point wiring with necessary flexible copper conductor of multistrand three core of suitable length from fitting to the ceiling roseall as directed.Make: Philips Model BN021C LED22Sor equivalent make in Havells/Wipro/GE. 181 S & F in replacement of Security Lights of 25 watt LED light with high power LED and unique peanut lens to ensure uniform distribution with suitable pipe bracket 32 mm dia 0.60 Mtr length fixed on wall with suitable flat iron clamps and nut bolts including provision of 1.5 sqmm 3 core multistranded copper conductor cable from light fitting to junction box complete all as specified and directed.Make: Havells Model ENDURASUNDOWNSL25WLED765PASYBOPCIHDor equivalent make in Wipro 182 Supply and fixing LED flood light 100 watt 230 V AC outdoor type with thermal management inmultiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp fixed on wall with suitable flat iron clamps and nut bolts including connecting to multistranded copper conductor cable from light fitting to junction box complete all as specified and directed. 183 S & F of LED Luminarie 600mmx600mm 35/36 watts, 220 volts AC recessed mounting light fixture type with high efficiency PMMA diffuser soft glare free light complete with driver, holders and LED lamp suitable for roof ceiling including connecting up with driver 3 core flexible copper conductor cases of suitable size complete with lumianrie system efficacy >100 lm/wwith IP & surge protection of 10 kV, power factor >0.95 complete with all accessories all as specified and directed by Engg-in-Charge . Note: Cutting of False ceiling and re-arranging the False ceiling with existing size, Gypsum board/POP false ceiling is to be done if required. Cost of False ceiling work is inclusive of rate quoted. 184 S & F in replacement of round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders LED lamps suitable for roof ceiling including connecting up with 3 core flexible copper conductor cable of suitable size complete with lumianrie system efficacy >100 lm/wwith IP & surge protection of 10 kV, power factor >0.95 complete with all accessories all as specified and directed by Engg-in-Charge . Note: Cutting of False ceiling and re-arranging the False ceiling with existing size, Gypsum board/POP false ceiling is to be done if required. Cost of False ceiling work is inclusive of rate quoted. . 185 S & F in replacement of round shape spot light of 06 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders LED lamps suitable for roof ceiling including connecting up with 3 core flexible copper conductor cable of suitable size complete with lumianrie system efficacy >100 lm/wwith IP & surge protection of 10 kV, power factor >0.95 complete with all accessories all as specified and directed. Note: Cutting of False ceiling and re-arranging the False ceiling with existing size, Gypsum board/POP false ceiling is to be done if required. Cost of False ceiling work is inclusive of rate quoted. 186 Supply, fix, test and commissioning of Decorative wall mounting fixture of 09 Watts in durable plastic body and designer mesh in gold finish suitable for 9 W LED lamp complete with all accessories all as per Cat No LHFOECE1TZ1B014 of Havells or techno- commercially equivalent of other specified makes connecting up with and including twin/ three core twisted flexible copper conductor cable of suitable size etc. complete all as specified and as directed. 187 Supply and Fix in replacement of 2 module Modular white cover plate with frame complete all as specified and directed 188 All as per Ser item No 184 but 3 module Modular white cover plate with frame. 189 All as per Ser item No 184 but 4 module Modular white cover plate with frame. 190 Supply and fix in replacement ofPVC Round blocks ofsize 4for proper mouting LED tube lights alongwith connected items for fixing complete all as specified and directed. 191 Refixing of Serviceable items obtained from ser item No 3 such as LED security light/ flood light fittiingswith suitable pipe bracket 32 mm dia 0.60 Mtr length fixed on wall with suitable flat iron clamps and nut bolts including provision of 1.5/2.5 sqmm 3 core multistranded copper conductor cable from light fitting to junction box complete all as specified and directed. 192 All as per ser item No 188 but items such LED tube light/Ceiling light fittings alongwith connected switch & sockets including provision of 1.5 sqmm 3 core multistranded copper conductor cable from light fitting to junction box complete all as specified and directed. 193 Earthing complete with galvanised steel earth plate electrode 60cm x60cm x6mm thick buried directly in ground earth pit not less than 2.25 mtr deep below normal ground level ) with top edge of plate not less than 1.5m below ground level, connecting to the Galvanised iron earth earth lead 4 mm dia, by means of nuts, bolts,check nuts and washer etc of galvanised iron and earth lead protected by provision of GI pipe light grade 15mm bore from earth elelctrode to test pointincl provn of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone agagregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4Kg/Sqm) and frame of angle iron 25 x 25x6mm with lugs 2 Nos and with 6mm dia MS bar handle made to shape, GI pipelight grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling test point made out of Bronze/Gun metalwith fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning in and removal of surplus soil to a distance not exceeding 50mtr, all as per electrical plate No 5 of SSR Part-I and connection to earth test point all as specified incl testing on completion. Note :- Item of Earthing includes cost of 7.5m long galvanised iron earth lead 4 mm size and protection pipe of 15 mm bore GI light grade.
