Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 07-06-2025 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 14-06-2025 |
| Sl. No. | Item Description |
| 1 | Schedule \"A\" Part-I (B/R itmes)Providing and injecting emulsion for post construction anti termite treatment using chemical chloropyriphos 20EC conforming to IS 8944 or lmidacloprid 30.50 SC conforming to IS 16131 concentrate along the external wall of buildingbelow concrete or masonry apron using chemical emulsion @ 2.25 litre per linear metre including drilling 12mm dia holes @ 300 mm apart and plugging holes with cement mortar 1:2 (1 Cement 2 Coarse sand) in apron etc,. complete all as specified and directed by Engr-in- charge. |
| 2 | Providing and injecting chemical emulsion for post construction anti termite treatment using chemical chloropyriphos 20EC conforming to IS 8944 or lmidacloprid 30.50 SC conforming to IS 16131 of soil under existing floorsusing chemical emulsion @ 1 Litre per hole 300mm apart including drilling 12mm dia holes @ 300 mm apart and plugging holes with cement mortar 1:2 (1 Cement & 2 Coarse sand) to match the existing floor and making good the disturbed sufaces to match with the existing surface, complete all as specified and directed by Engr-in- charge. |
| 3 | Providing and injecting chemical emulsion for post constructional anti termite treatment at points of contact of wood work by usingchemical chloropyriphos 20EC conforming to IS 8944 or lmidacloprid 30.50 SC conforming to IS 16131 emulsion in oil or kerosene based solution@ 0.5 litre per hole by drilling 6mm dia holes at a downward angle of45 degree @ 150mm centre to centre and sealing the same and making good the disturbed sufaces to match with the existing surface, complete all as specified and directed by Engr-in- charge. |
| 4 | Demolition of cement concrete (unreinforced) of any descriptionand in any position including any type of sunken treatment , roof treatment, PCC padding, roof PCC tiles,lime concrete etc. , complete all as specified and directed by Engr-in- charge.Note: All Demolished material / debries will be taken by the contractor out side of thecantonment without any extra cost to the govt,contractor should quote his rate Keeping this aspect in mind. |
| 5 | Material & Labour cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 or PCC (1:2:4) type B-5 , complete all as specified and directed by Engr-in- charge. |
| 6 | Material & Labour cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) , complete all as specified and directed by Engr-in- charge. |
| 7 | Material & Labour PCC (1:3:6) type C1 using 20 mm graded stone aggregate as inmass concrete over roof as in padding incl cement slurry @ 3Kg/Per sqm over old RCCsurface, surfacefinished even & smooth without using extra cement. all as specified and directed by Engr-in- charge. |
| 8 | Material & Labour ,15 mm thick plaster in cement mortar (1:4) over concrete surfaces of roofs finished even and smooth with WPC @ 3% by weight of cement ( WPC will be measured paid for seperately) as in roof treatment workall as specified and directed . |
| 9 | Material & Labour for providing and laying 3mm thick APP (atactic polypropylene polymer) modified prefabricated five layer weight not less than 3.60 kg /Sqm water proofing membrane black finish reinforced with non woven polyster matt and consisting of a coat bituminous primer @ 0.40 litre /Sqm by the same membrane manufactures of density 0.87 to 0.89 kg/ltr at 25 degree centegrate temperature and viscosity 70–160 cps over the primer coat with overlap of 100mm at theside and 150mm at the end, the layer membrane shall be laid using butane gas torch and sealing all joints etc. after preparing the surface complete as per standred practice as per manufacture\"s instructions. The vital physical and chemical parameters of the membrane shell be under :–(i) Joint strength in longitudinal and transverse direction at 23 degree centegrate at 650/ 450 N /5 cms(ii) Tear strength in longitudinal and transverse direction at 300/250N/5 cms. Softing point of membrane not less then 150 degree centegrate when tested in accordance with ASTM (d–5147)(iii) The laying of membrane shell be got down through the authorised applicator of manufactures of membrane only, complete, all as specified and as directed.(iv)The work shall be carriout at a height upto 12 metre. |
| 10 | Material & Labour for 40 mm thick Precast cement concrete Tile, type B-0, 1:2:4 (12.5mm graded stone aggregate) as in roof flooring, bedded over and including 15 mm thick cement mortar (1:6) ,and jointed in cement mortar (1:6) and pointed in cement mortar (1:3) , complete all as specified and directed by Engr-in- charge. |
| 11 | PCC 1:2:4 type B1 (20mm graded aggregate ) as in roof kerb, fillets at junctions between roof and parapet walls, copings rounded or chamfered angles . |
| 12 | Dismentling of brick work built in cement mortar or cement lime mortar including all quoins, arches,pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles , complete all as specified and directed by Engr-in- charge. |
| 13 | Material & Labourbrick work with sub class \"B\" old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 , complete all as specified and directed by Engr-in- charge. |
| 14 | All as per serial item No. 13 here in befor but except bricks(old serviceable bricks obtained from serial item No 12above including removing motar, cleaning the bricks with water, shall be used), complete all as specified and as directed by the Engineer–in–Charge. |
| 15 | Material & Labour brick work with sub class -B bricks, in half brick thick walls, built in cement moratr 1:4 straight or curved on plan to any radius , complete all as specified and directed by Engr-in- charge. |
| 16 | Material and labour rendering 15 mm thick(in patches) on brick work or concrete wall surfaces in cement mortar (1:4)including mixing water proofing compound @ 2% by weight of cement or as per manufacturer\"s instruction and finished even and smooth without using extra cement complete, all as specified and as directed by the Engineer-in-Charge. ( Note- The cost of providing WPC shall be measured paid for seperately) |
| 17 | Supply only integral water proofingcompound, complete all as specified and directed by Engr-in- charge. |
| 18 | Material & Labour for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid by torch forced application over and including a coat of bitumen 85/25 grade applied hot @ 1.20 Kg/Sqmas in sunken portion, , complete all as specified and directed by Engr-in- charge. |
| 19 | Dismantling floor,hearth or wall tilling including cement mortar bedding (but not backing ),removing serviceable tiles to store and rubbish off premises , complete all as specified and directed by Engr-in- charge. |
| 20 | Demolition of plain cement concrete (unreinforced) including any type of flooring any descriptionnot exc 15 cm, complete all as specified and directed by Engr-in- charge. Note: All Demolished material / debries will be taken by the contractor outcm side of thecantonment without any extra cost to the govt.contractor should quote his rate Keeping this Aspect in mind. |
| 21 | Material & Labour providing 75 mm thick cement concrete (1:3:6) type C-1 using 20mm graded crushed stone aggregates as in plinth protection, laid in alternatebays (not exc 2 Sqm each )and finished even and smooth without using extra cement and providing jointsthroughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight including form work, complete, all as specified and as directed. |
| 22 | Material & Labour for 25 mm thick Cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in sub base floors, surface fair finished and even and rough to receive floor finishes , complete, all as specified and directed. |
| 23 | Material & LabourNon Skid coloured ceramic tiles joint freepremium/1st quality 7 to 8 mm thick, (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over andincluding15mm thick screed bed in CM 1:6 complete all as specified and as directed. |
| 24 | Material & LabourNon Skid coloured ceramic tiles premium/1st quality of same description as of floor tiles in serial item No 23abovebut 100mmto 200mm heightas in skirting, set and jointed in neat cement slurry and pointed in white or colouredcement mixed with pigmentto match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4complete all as specified and as directed by the Engineer-in-Charge. |
| 25 | Material & Labour for glazed ceramic coloured tiles 450x300x7mm thick on vertical surfaces such as dados set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coatin cement mortar (1 :4) complete all as specified and as directed. |
| 26 | Material & Labour 10mm thick heavy duty, coloured paver tilesof size 300 x 300x 10mm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20mm thick screed bed in cement mortar (1 :4) ,complete all as specified and as directed by the Engineer-in-Charge. |
| 27 | Dismantling stone slab of any description or thickness laid, bedded and pointedin any motar in floors etc , complete all as specified and directed by Engr-in- charge. |
| 28 | Material & Labour for Granite (of any type)slab 18-20 mm thick machine cut ,bedded and jointed with gray cement slurry and pointed with white cement as in floors/ cooking plateform, with admixiture of pigment to match the shade of granite stone including grindingand polishing complete over and including20 mm thick screed bed in CM 1:6 , complete all as specified and directed by Engr-in- charge. |
| 29 | Material & Labour for Granite (of any type)slab 18-20 mm thick machine cut , jointed with gray cement slurry and pointed with white cement as in vertical surfaces / dado / skirtingwith admixiture of pigment to match the shade of granite stone indluding grindingand polishing complete over and including10 mm thick backing coat in CM 1:4 , complete all as specified and directed by Engr-in- charge. |
| 30 | Material & Labour rounding to edges of stone slabboth edge such as in steps, cooking plateformand other similar situtaions withgrinder, complete all as specified and directed by Engr-in- charge. |
| 31 | Material & Labour machine cut kota stone slab flooring 18 to 22 mm thick in floor/landing/treads of stairs,set and jointedin neat cement slurrywith greycementmixed withpigment to match the shade of the slab including rubbing and polishing (granite finish) over and including 15 mm thick screed bed in CM 1:4 , complete all as specified and directed by Engr-in- charge. |
| 32 | Material & Labour machine cut kota stone slab flooring 18 to 22 mm thickin skirting , set and jointedin neat cement slurrywith greycementmixed withpigment to match the shade of the slab including rubbing and polishing (granite finish) over and including 10 mm thick renderingin CM 1:4 , complete all as specified and directed by Engr-in- charge. |
| 33 | Material & Labour machine cut green marble stone slab flooring 18 to 22 mm thickin floor, window cills,set and jointedin neat cement slurrywith greycementmixed withpigment to match the shade of the slab including rubbing and polishingover and including 15 mm thick screed bed in CM 1:6 , complete all as specified and directed by Engr-in- charge. |
| 34 | Material & Labour machine cut green marble stone slab 18 to 22 mm thickin skirting , set and jointedin neat cement slurrywith greycementmixed withpigment to match the shade of the slab including rubbing and polishing over and including 10 mm thick renderingin CM 1:4 , complete all as specified and directed by Engr-in- charge. |
| 35 | Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed by Engr-in- charge. |
| 36 | Material & Labour for Reinforced cement concrete design mix M-25 using 20mm graded stone aggregate, as in Slabs supported on walls, beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the likedack slab , complete all as specified and directed by Engr-in- charge. |
| 37 | Material & Labour reinforced cement concrete design mix M-25 using 20mm graded stone aggregate, graded stone aggregate as inchajjas,Fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels,balustrade, and the like complete all as specified and directed by engineer in charge . |
| 38 | Material & Labour formwork to chajjas, fins, louvres, facias including edgesfor rough finished surfaces of concrete flats , complete all as specified and directed by Engr-in- charge. |
| 39 | Material & Labour formwork to soffits ofsuspended slabs such roof slab, floor slabs, landings and similar work not exceeding 20 centimetre thick (horizontal or sloping) flat for rough finished surfaces of concrete , complete all as specified and directed by Engr-in- charge. |
| 40 | Material & Labour formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofsand sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide, for roughed finished surface of concrete , complete all as specified and directed by Engr-in- charge. |
| 41 | Material & LabourTMT steel bars 10mm dia and over cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia , complete all as specified and directed by Engr-in- charge. |
| 42 | Taking down chowkats or frames with shutter areanot exceeding 1.50 Square metre (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish , complete all as specified and directed by Engr-in- charge. |
| 43 | Taking down chowkats or frames with shutter area exceeding 1.50 Square metre andnot exceeding 4.00 Square metre (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish , complete all as specified and directed by Engr-in- charge. |
| 44 | Taking down shutters of any description area exc 1 sqm and not exc 2 sqm each and removing the same from site , complete all as specified and directed by Engr-in- charge. |
| 45 | Supply and fixing mild steel framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 , complete all as specified and directed by Engr-in- charge. |
| 46 | Cutting holes in brick walls built in cementmortar exceeeding half brick thick and not exceeding one brick thick wall for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 (Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall)as required , complete all as specified and directed by Engr-in- charge. |
| 47 | Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/ chowkhat of size 50 x 75 mm comprising of virgin PVC polymer of K value 58–60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant , complete all as specified and directed by Engr-in- charge. |
| 48 | Supply and fixing Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M. S. tubes for top & bottom rails. M. S. frame shall be covered with heat moulded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M. S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed by Engr-in- charge. |
| 49 | Supply and fixing of factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/chowkhat of size 100 x 65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with mild steel hold fast of required dia and length complete all as specified and directed.NOTE : - (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made.(ii) Material manufacture test certificate should be provided before execution of work |
| 50 | Supply and fixing of factory made single extruded WPC (Wood PolymerComposite) solid door/ window/ Ceosetory windows & other frames/chowkhat of size 125 x 65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with mild steel hold fast of required dia and length complete all as specified and directed.NOTE : - (i) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made.(ii) Material manufacture test certificate should be provided before execution of work |
| 51 | Supply and fixing of factory made single extruded WPC (Wood Polymer Composite) solid decorative type moulded ( Jointless ) door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing withfull body threaded star headed counter sunk S.S screws, completeall as per specification & drawing complete all as specified and directed |
| 52 | Supply and fixing of factory made single extruded WPC (Wood Polymer Composite) solid decorative type moulded ( Jointless ) gauzed door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing withfull body threaded star headed counter sunk S.S screws, completeall as per specification & drawing complete all as specified and directed. Note : Stainless steel wire mesh should be paid under separate item . |
| 53 | Material and labour for Providing and Fixing of windows made of pre-painted steel (Base steel as per IS 513 of 0.58 mm thick “D” Quality galvanized as per IS 277 with Zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for shutter frame should be of 52x25mm and size of flymesh shutter should be of 20x40mm and rebate for Glazed shutter and flymesh shutter with a 20mm provision for Guard bars/Grills. The sections are to be cut to length metre joined with corner bracket. Centre mullion is to be fixed with mullion cap. Shutter brackets with a inbuilt pvc lip to be fixed in a way that the lip overlaps the shutter corners and are not exposed. Handle,stay, 2 nos. of Stainless Steel heavy duty Pivot hinges shall be provided per shutter the windows fitted with 4mm thick plain float/frostedglass with rubber gaskets including fixing the frames in concrete/masonry wall by MS holdfast, Including fixed panel beading section should be of 12x12mm. Outer frame and mullions to have 10mm Square guard bars with 6” (152.4mm) pitch etc., complete for finished item of work.(Make: Elixir Met Form Pvt Ltd. / A2Z Infra Solutions / Urban Space ) |
| 54 | Supply and fixing box type using ERW hollow \"P\" section ventilators fixed type with glazing barincluding MS grills of square bar 10mm dia @ 100 c/c complete with glazing bars dovetailed or welded, including two coat of synthetic enamel ordinary tint paint over a coat of red oxide primer , complete all as specified and directed by Engr-in- charge. |
| 55 | Material & Labour sheet glass 3.00mm thick ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane, complete all as specified and directed by Engr-in- charge. |
| 56 | Supply and fixing mild steel works in bands, straps, supports, stays, bolts, hooks, hold fasts etc, similar articles conforming toFe-290.Gde-E-165, complete all as specified and directed by Engr-in- charge. |
| 57 | Material & Labour18 mm thick prelaminated particle board exterier grade (grade-1) confirming IS 14587,prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws for kitchen cupboard and cabinet , shelves for cupboard, frame with door if required including 3mm thick 2nd class hardwood leeping patti on cut edge of boards , complete all as specified and directed by Engr-in- charge. |
| 58 | Material & Labour Plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails of 2nd class hardwood of sectional area exc 13 sqcm not exceeding 25 sqcm, complete all as specified and directed by Engr-in- charge. |
| 59 | Supply and fixing Continuous (piano) hinges, width of flaps 30mm mild steel, bright finish or electro galvanised , complete all as specified and directed by Engr-in- charge. |
| 60 | Supply and fixing 75 mm long brass handle casttype polished bright , complete all as specified and directed by Engr-in- charge. |
| 61 | Supply and fixing brass body ball catches with 8mm dia steel ball and striking plate including letting in, complete all as specified and directed by Engr-in- charge. |
| 62 | Supplyand fixing as in repair stainless steel wire cloths0.36 mm nominal dia of wire and averagewidth of aperature 1.40 mm and fixed with stainless steelwire staple, complete all as specified and directed by Engr-in- charge. |
| 63 | Supply and fixing 100 mm long butt hinges extruded aluminium alloy with galvanised mild steel hinge pine including screwing or welding to MS / PVC frame (as required) , complete all as specified and directed by Engr-in- charge. |
| 64 | Supply and fixing 150 mm long aluminium handle casttype anodised , complete all as specified and directed by Engr-in- charge. |
| 65 | Material & Labour 2nd class hard wood Small fitting such a brackets of any type ,latch and hinge block , shaped door and window stops and the like including all necessary labours articles n. exc200 Cu cm each including 50mm long mild steel cold rolled medium weight but hinge , complete all as specified and directed by Engr-in- charge. |
| 66 | Supply and fixing as in repairmild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller plate including welding or screwing to MS frame , complete all as specified and directed by Engr-in- charge. |
| 67 | Supply and fixing 150 mm long aluminium anodised barrel tower boltsof extruded section and fixed, complete all as specified and directed by Engr-in- charge. |
| 68 | Supply and fixing 200 mm long aluminium anodised barrel tower boltsof extruded section and fixed , complete all as specified and directed by Engr-in- charge. |
| 69 | Supply and fixing 250mm long aluminum alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloys to door shutter , complete all as specified and directed by Engr-in- charge. |
| 70 | Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer–in–Charge. |
| 71 | Material & Labour galvanised iron tubing 15mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floorsas in repair, complete all as specified and directed by Engr-in- charge. |
| 72 | Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed by the Engineer–in–Charge. |
| 73 | Material & Labour galvanised iron tubing 20mm bore medium grade with all fittings and fixed complete to walls and ceilings or laid in floorsas in repair, complete all as specified and directed by Engr-in- charge. |
| 74 | Cuttingchases to brick wall built in cement mortar, pinning in making good to facing where required and pointing in CM 1:3 to edges of landing , steps , cills , sunshades, shelves , lintel etc. and cutting chases for concealed water tubing etc and making good cutting not exc 10 cm girth, complete all as specified and directed by Engr-in- charge. |
| 75 | Supply and fixing 600mmx450mm bevelled edge mirror 5mm thick of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers,as in repair , complete all as specified and directed by Engr-in- charge. |
| 76 | Supply and fixing in repair Vitreous china orissa pan squatting pattern 580 X 440mm with integeral foot rests includingP or S trapandincluding PVClow level flushing cistern 10 ltrs capacity and Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, complete all as specified and directed by Engr-in- charge.Note : The cost of traps , flushing cistern and PVC flush pipes are included in this item. |
| 77 | Supply and fixingvitreous china wash hand basin white, flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing ofwaste fitting etc as in repair , complete all as specified and directed by Engr-in- charge. |
| 78 | Supply and fixingsinks with drainage board made out of stainless steel 1mm thick sheet for kitchenwith plugs, waste pipe, brass chromium plated coupling including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mmwith bowl size 410mm x 330mm x 160mmas in repaircomplete all as specified and as directed by the Engineer-in-Charge |
| 79 | Supply and fixing as in repairfancy type pillar tap of 15mm bore, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe , complete all as specified and directed by Engr-in- charge. |
| 80 | Supply and fixingas in repair15mm bore cast copper alloy chromium plated angular stop valveswith capstan head, screwed down, high pressure scrwed both ends for iron pipe or for unions , complete all as specified and directed by Engr-in- charge. |
| 81 | Supply and fixing as in repair bib taps 15mm bore fancy type brass chromium plated with long body,wall flanges and capstan head,screwed down,screwed for iron pipe or for brass ferrule and fixed , complete all as specified and directed by Engr-in- charge. |
| 82 | Supply and fixing as in repair brass chromium plated shower rose 125mm size swivel type with arm of standard size as per site , complete all as specified and directed by Engr-in- charge. |
| 83 | Supply and fixing 15mm bore cast copper alloy fancy type chromium plated stop valves with long shank and cup (concealed type), screwed down, high pressure with capstan head, scrwed both ends for iron pipe or for unions as in repair , complete all as specified and directed by Engr-in- charge. |
| 84 | Supply and fixingPVC connections 15 mm sizewith PTMT nuts of length 450 mmas in repair , complete all as specified and directed by Engr-in- charge. |
| 85 | Supply and fixingbrass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges as in repair , complete all as specified and directed by Engr-in- charge. |
| 86 | Supply and fixing in repairStainless steel ( SS 202 grade ) Curtain rod25 mm dia 0.80 mm wall thickness, mild steel, chromium platedincluding ornamental typesupporitng and end brackets as per sample , complete all as specified and directed by Engr-in- charge. |
| 87 | Supply and fixing sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 mm wide with chromiun plated brackets guard and railing 60 cm long as in reapir complete all as specified and as direced by the Engineer–in–charge. |
| 88 | Supply and fixingas in repair 100mm bore PVC (SWR) floor trap, plain with chromium plated grating including jointing with solvent cement , complete all as specified and directed by Engr-in- charge. |
| 89 | Supply and fixing in repair Soap Dishas approved Design of Jaquar Cat Part No AHS 1531complete all as specified and directed by Engr in Charge . Make Jaquar or equivalent given in appendix \"B\" |
| 90 | Supply and fixing and connecting to make it operational, water storage tank, 500 ltr capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm dia high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore and including 20mm bore tank nipple & one 20mm GI union at outlet and including dismantling of existing unsv water tanks and removing from site, all as specified in SSR Part–I , complete allas specified and directed by Engr-in- charge.Note : - The colour of tanks shall be white colour . |
| 91 | Supply and fixing and connecting to make it operational, water storage tank, 1000 ltr capacity, HDPE triple layer, white colour, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm dia high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore and including 20mm bore tank nipple & one 20mm GI union at outlet , all as specified in SSR Part–I , complete all as specified and directed by Engr-in- charge.Note : - The colour of tanks shall be white colour . |
| 92 | Cutting into existing manholes for connecting new drains, and making good to pipe and rendering, cutting out existing benching for and forming branch channel( 1/2 round or 3/4 section ) in cement concrete 1:2:4 type B-1 (using 20mm size crushed stone aggregate) smooth finished and reforming benching as required of pipe 75/100/110 mm bore, complete all exixting unserviceable as specified and directed by Engr-in- charge. |
| 93 | Excavation in trenches, not exc 1.5 m wide and not exc 1.5 m in depth for foundation etc for laying of cables, pipe etc. or for shafts, wells, manholes etc. not exc 10 sqm on plan and not exc 1.5 m in depth and getting out in soft/ loose soil complete all as specified and as directed by the Engineer-in-Charge. |
| 94 | Returning filling in including spreading, levelling, watering and wall ramming in layer n exc not exc 25 cm, any kind of soil , complete all as specified and directed by Engr-in- charge. |
| 95 | Removing surplus excavated materialto a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point , complete all as specified and directed by Engr-in- charge. |
| 96 | Demolition and breaking up drain pipes and rainwater pipes up to 150 mm bore (any size or pattern), including all fittings, heads, shoes, bends, swan–necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) , complete all as specified and directed by Engr-in- charge. |
| 97 | Supply and fixing 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floor or fixed to wall , complete all as specified and directed by Engr-in- charge. |
| 98 | Supply and fixing 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall , complete all as specified and directed by Engr-in- charge. |
| 99 | Supply and fixing 110mm bore PVC (SWR) bends of any radius with access doors ,complete all as specified and directed by Engr-in- charge. |
| 100 | Supply and fixing 75mm bore PVC (SWR) bends of any radius with access doors , complete all as specified and directed by Engr-in- charge. |
| 101 | Supply and fixing 110mm bore PVC (SWR) juction double (double T) equal are unequal with acces door , complete all as specified and directed by Engr-in- charge. |
| 102 | Supply and fixing 110mm bore PVC (SWR) juction single (Single T) equal are unequal with acces door , complete all as specified and directed by Engr-in- charge. |
| 103 | Material and Labour for PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement,, complete all as specified and directed by Engr-in- charge. |
| 104 | Supply and fixing 75 mm bore PVC (SWR), vent cowls including jointing with solvent cement, , complete all as specified and directed by Engr-in- charge. |
| 105 | Supply and fixing 110 x 75 mm bore PVC (SWR), reducerincluding jointing with solvent cement,, complete all as specified and directed by Engr-in- charge. |
| 106 | Supply and fixing Hard drawn steel wire fabric cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcent (Weight per square metre N exc4 Kg),complete all as specified and directed by Engr-in- charge. |
| 107 | Taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key scrubbing down with water etc , complete all as specified and directed by Engr-in- charge. |
| 108 | Material and labour for rendering 15 mm thick on brick work or concrete wall surfaces in cement mortar 1:6 including mixing water proofing compound @ 2% by weight of cement or as per manufacturer\"s instruction and finished fair and even without using extra cementincluding necessary scaffolding etc., complete all as specified and as directed by the Engineer–in–Charge. (WPC shall be measured and paid for separately) |
| 109 | Material & Labour rough cast plaster complete as specified in SSR Part–I, clause 14.22 shall consisting of following :– firstly apply under coat in cement mortar 1:3 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine gravel aggregate which is generally of size between 6 to 12 mm depending on texture required mixed with coarse sand and cement in the ratio 1:1:1 shall be applied, complete all as specified and as directed by the Engineer–in–Charge. |
| 110 | Material and labour for rendering 15 mm thick on brick work or concrete wall surfaces in cement mortar 1:4 including mixing water proofing compound @ 2% by weight of cement or as per manufacturer\"s instruction and finished fair and even without using extra cementincluding necessary scaffolding etc., complete all as specified and as directed by the Engineer–in–Charge. (WPC shall be measured and paid for separately) |
| 111 | Material and labour for preparation of newly plastered/ unplastered surfaces of walls and applying two coats of oil bound distemper with painting rollerover and inlcuding 1mm to 2mm thick wall care putty white cement based in two or more coats to achive smooth surface complete all as specified and as directed by the Engineer–in–Charge. |
| 112 | Material & Labour preparation of newlyplastered/ unplastered surfaces of brick/ concretewall and applying two coats of white lime wash , complete all as specified and directed by Engr-in- charge. |
| 113 | Material & Labour rendering 05 mm thick on any faces of brick work or concrete ceiling surfaces in cement mortar (1:3) andfinishedeven and smooth without using extra cement , complete all as specified and directed by Engr-in- charge. |
| 114 | Material and labourfor preparation of new plastered/unplastered surfaces and applyingthree coats of white lime wash on surfaces of ceiling, chajjas, roof projection complete all as specified and as directed by the Engineer-in-Charge. |
| 115 | Material & Labourpreparation of new steel surfacesof any description, not otherwise described, over10 cm width or girth and applying two coats of synthetic enamel paintover a coat of red oxide primer , complete all as specified and directed by Engr-in- charge. |
| 116 | Material & Labourpreparation of new wooden surfaces or WPC surfaces of any description, not otherwise described, over10 cm width or girth and applying two coats of synthetic enamel paintover a coat of pink primer , complete all as specified and directed by Engr-in- charge. |
| 117 | Material & Labourpreparation of old decorated woodensurfacesof any description, not otherwise described, over10 cm width or girth and applying twocoats of synthetic enamel paint , complete all as specified and directed by Engr-in- charge. |
| 118 | Material & Labour for hardcore of broken stone or boulders gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and remmed to a true surface, complete all as specified and as directed by the Engr-in-Charge. |
| 119 | Material and labour for providing PCC (1:4:8) Type D2 using 40mm graded crushed stone aggregate as in foundations, filling and mass concrete, complete all as specified and as directed by the Engineer-in-Charge. |
| 120 | Material and labour for vibratory rubber moulded precast coloured concrete interlocking paver block, shape and sizeconforming to IS 15658-2006, ISI marked of 80 mm thickness, grade M-40 with grey cementover and including a layer of sand cushioning, 25 mm thick,complete, all as specified and as directed by the Engineer-in-Charge. |
| 121 | Material & Labour for Stainless steel plate rack of size 31\" x 30\" x 10\" of load capacity not less than 30 kg including fixing with stainless stell screws including taking down of old plate rack of any description , complete all as specified and directed by Engr-in- charge. |
| 122 | Material and labour for repairing of RCC projection, chajjas, facia, bands, shelves, beams, RCC railing, balcony and similar works by dismantling of loose/ disintegrated portion of RCC at any height and in any sitution / floor (including provn of support,formwork and welding of reinforcement if required with wire mesh of weight 3 kg/ sqm and dubbing/ fillingwith PCC (1:2:4), type B-0, using 12.5 mm graded aggregate,15 to 25 mm thick over and includingapplying cement slurry @ 3 kg/sqm, finished even and smooth to desired shape , complete all as specified and directed by Engr-in- charge.Note:-(i) Unit rate of this item includes the cost of scaffolding,formwork etc. and nothing extra shall be paid on account of variation in height. (ii) Wire mesh shall be measured and paid for separately |
| 123 | Desilting of manhole complete by removing all , sludge, silt (both organicand inorganic nature) bymanual labour or mechanical scraper and disposal of the same in closed container at authorized dumping site declared by local administration outside MD landand buried in trenches etc, as in foul condition for any depth, , complete all as specified and directed by Engr-in- charge.Note:- Sludge,silt (both organicand inorganic nature) water shall be disposed off in closed container at authorized dumping site declared by local administration outside MD land. |
| 124 | Schedule \"A\" Part-II (E/M itmes)Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder, socket outlet, etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etccomplete all as specified and as directed by the Engineer-in-Charge. |
| 125 | Material and labour for point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling surfaces and including provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade, ISI marked with multi stranded copper conductorgreen colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes modular type of size/modules as required at site with earth dolly(boxesshall be galvanised or painted with two coats of anti corrosive paint over a coat of red oxide primer bothinternally and externally) including provision of new covered plate over sunken box for housing themodular switches , modular socket outlets,modularfan regulators etc.for one light/fan/exhaust fan/bell point controlledby one way switch,complete all as specified and as directedby Engineer-in-Charge. Note :-a) .All chases will be cut by chase cutter only b) Switch, socket outlet and fan regulators to be measured and paid forseparately . |
| 126 | Description all as per serial item No.125 here-in-before but for One 3 pin, 6 Amps, socket outlet controlled by one switch on independent board,complete all as specified and as directedby Engineer-in-Charge. |
| 127 | Description all as per serial item No.125 here-in-before but for One 3 pin 6 Amps socket outlet controlled by one switch on same board,complete all as specified and as directedby Engineer-in-Charge. |
| 128 | Material & Labour for concealed point wiring complete with 2.5 Sqmm single core multistranded copper conductor FRLS PVC insulated and unsheathedcable 1100 volts grade drawn through and including medium grade, ISI marked, PVC conduit,medium grade ISI marked not less than 20 mm dia with accessories fixed concealed/surface type on wall/ roof/ ceiling and including provision of 2.50 sqmm single core PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor green colour as earth conitnuity conductor and connected to common earth dolly with suitable size lugs, including mild steels sunken box or pressed steel terminal box or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-1) of 1969 and IS:14772:2000 with earth dolly and coated with two coat of anti corrosive paint over a coat of red oxide primer both internally and externally with and including (provision of new) modular covered plate over sunken box for housing the modular switches, socket outlets., fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for :-Note:-1 Modular metal flush / sunken box, and for modular switch/ socket cover plate & sheet are inclusive in the item rate quoted. |
| 129 | Supply and fixing of modular switch 1 module, single pole, one way 6 Amps flush type, 230 voltscomplete all as specified and as directedby Engineer-in-Charge. |
| 130 | Supply and fixing of modular switch 1 module, single pole, one way 16 Amps flush type, 230 voltscomplete all as specified and as directedby Engineer-in-Charge. |
| 131 | Supply and fixing of modular socket outlet2/3 pin combined,6 Amp, one way, two module, 230 voltscomplete all as specified and as directedby Engineer-in-Charge. |
| 132 | Supply and fixing ofmodular socket outlet3/3 pin combined, (6pin), 6 and 16 Amps, one way, two module, 230 voltscomplete all as specified and as directedby Engineer-in-Charge. |
| 133 | Supplyand fixing of modular bell push 6 Amp, 1 way, 1 module, 230 volts complete all as specified and as directed by the Engineer-in-Charge. |
| 134 | Supply and fixing in repair calling bell ding dong 230 volt, complete all as specified and as directed by the Engineer-in-Charge. |
| 135 | Supply and fixing ceiling rose surface type 2/3 terminalpolycarbonate, isolated body complete all as specified and as directed by the Engineer-in-Charge. |
| 136 | Supply and fixing lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings, complete all as specified and as directedby Engineer-in-Charge. |
| 137 | Supplyand fixingas in repairelectronic Fan regulator modular 100 watt, 1 module, 230 volts , 50 Hz, AC supply suitable for ceiling fan any type/make/sweep complete all as specified and as directed by the Engineer-in-Charge. |
| 138 | Supply and fixing in repairLED batten fitting 18-20 watt, 4 feet, aluminium housing with electronic drivercool/warm typeindustrial model complete,connecting with copper conductor flexible cablefrom ceiling rose to connector of the light complete all as specified and as directed by the Engineer-in-Charge. Cat part No. LUMILINE+ BS20WLED865SPCSS of make Havells or equivalent in make given in Appx \"B\". |
| 139 | Supply and fixing in repair,LED batten fitting 10-12 watts, 2 feet, aluminium housing with electronic drivercool/warm typeindustrial model complete,connecting with copper conductor flexible cablefrom ceiling rose to connector of the light complete all as specified and as directed by the Engineer-in-Charge. Cat part No. LUMILINE+ BS10WLED865SPCSS of make Havells or equivalent in make given in Appx \"B\". |
| 140 | Supply and fixing in repair, LED surface mounted bulk head luminaries, 8-10 watts, with min 800 lumen, industrial model, IP 65, aluminium housing, surge protection including driver and LED lamp, etc. complete with all accessories, connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed by the Engineer-in-Charge. Cat part No. HEXAFT10WLED857SSYMBOPC of make Havells or equivalent in make given in Appx \"B\". |
| 141 | Supply and fixing in repair,LED Bldg Security Light Fittings of capacity 35 watt made up of die castaluminiumhousing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including electronic driver and making electrical connection, complete all as specified and as directed by the Engineer-in-Charge.Cat part No.ENDCITYLIT PLAT + SL35WLED757SASYBOPCWOSPD of make Havells or equivalentin make given in Appx \"B\". |
| 142 | Supply and laying as in repair sub main wiring with two run of 4 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 4 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI markedmulti stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium gradeISI marked of adequate size for housing the wires complete all as specified and as directed by the Engineer-in-Charge.Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB.(ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length. |
| 143 | Supply and laying as in repair sub main wiring with two run of 6 sqmm PVC insulated , unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 6 sqmm PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI markedmulti stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and includingPVC conduit medium gradeISI marked of adequate size for housing the wires complete all as specified and as directed by the Engineer-in-Charge.Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB.(ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length. |
| 144 | Supply and fixing MCB SPN, 40 Amps, 240 volt,10 KA ,\"B\" curve as per site requirement including removing old unserviceable MCB complete all as specified and as directed by the Engineer-in-Charge. Cat part No 811035 of make Indoasian or equivalent make given in Appx \"B\". |
| 145 | Supply and fixing MCB SP, 5 to 32 Amps, 240 volt,10 KA ,\"B\" curve as per site requirement including removing old unserviceable MCB complete all as specified and as directed by the Engineer-in-Charge. Cat part No 811008 to 811015 of make Indoasian or equivalent make given in Appx \"B\". |
| 146 | Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket 20 Amp complete with and including one single pole MCB 20 Amp, 10 KA \"B\" curve including removing old unserviceable enclosure complete all as specified and as directed by the Engr–in–charge. Cat part No. 811955 of make Indo Asian or equivalent in make given in Appx \"B\". |
| 147 | Supply and fixing sheet metal enclosuretriple pole & neutral(TPN) IP-54 With and including MCB TPN-63 Amps, 16 KA, 415 volts, 4 way with 200 Amp rated bus bar flush /surface mounting double door duly grouted in solid block wall or on wooden board in and includinglugs/thimbles duly crimped for connectionincluding making smooth the disturbed surface including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge. Cat part No.811857 of make Indo Asian or equivalent make given in Appx \"B\". |
| 148 | Supply and fixing sheet metal MCB DB SPN 12 way with 200 Amps rated bus bar single pole and neutral withdouble door IP-54 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge. Cat part No.811828 of make Indo Asian or equivalent make given in Appx \"B\". |
| 149 | Taking down ceiling fan, cleaning the same and refixing after cleaning in any model/size etc and making all connection using three core copper conductor flexible cable in size 1.5 sqmm including drawn through PVC flexible conduit pipe from ceiling rose to fan connector complete all as specified and directed. |
| 150 | Material and labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earthwire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron.Earth wire protected by GI pipe 15mm bore(medium grade) and connected to earthing test pointas directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm c/cboth ways with one handle for liftingmade out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testingas in repair complete all as directed by Engineer-in-Charge and earth testing on completion. |
| 151 | Supply, laying,testing & commissioningXLPE insulated, armoured heavy duty electric cable 25 sqmmcross sectional area, 4 corewith stranded aluminium conductor, 1100 volts grade as in repair complete all as specified and as directedby Engineer-in-Charge. Note: execavation & earth work shall be measured in B/R portion schedule \"A\" Part-I. |
| 152 | Supply and laying well burnt brick class–B laid flat to cover the cable with width equal to the length of cable and abutting each other for protection of cable complete all as specified and as directed by Engineer–in–Charge. |
| 153 | Material and labour for dry sand cushoning to cable i.e 8 cm before laying cable in trenches and 15 cm after laying the cable and compacting complete all as specified and as directed by Engineer–in–Charge. Note: punned thickness shall be measured for payment. |
| 154 | Supply and fixing as in repairlight grade GI Tubing of size 40mm dia for cable protection and fixed with clamp to pole and wall with nut, bolts, washers complete all as specified and as directedby Engineer-in-Charge |
| 155 | Note:-Amount of credit ofRs. 68,726.00for retrieved materials is mentioned in Schedule of Credit Page No. .123 to 124 of tender documents in pdf form which will be deducted offline while acceptance of tender. |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
