Tender For Construction Work Of Class Room Block, Guard Room, Toilet Block And Cycle Stand Shed At Govt. Girls Degree Gollege, Roberts Ganj District-Sonbhadra., Robertsganj-Uttar Pradesh

TDR : 49174479

Tender Notice
BOQ

Expired

Robertsganj , Uttar Pradesh

Tender Brief : Tender For Construction Work Of Class Room Block, Guard Room, Toilet Block And Cycle Stand Shed At Govt. Girls Degree Gollege, Roberts Ganj District-Sonbhadra.

Document Fees
₹ 17700 /-

EMD
₹ 593000.0 /-

Tender Value
₹ 2.91 Crore /-

Submission Date
21-05-2025

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Construction Work of Classn Room Block, Guard Room, Toilet Block & Cycle Stand Shed at Govt. Girls Degree Gollege, Roberts Ganj District-Sonbhadra.
2	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.
3	All kinds of soil.
4	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
5	Excavating, supplying and filling of local earth (including royalty) by mechanical transport up to a lead of 5 km, also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc., complete.
6	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
7	1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources).
8	Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.
9	Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources). LINTEL
10	Ground Floor
11	First Floor
12	Mumty
13	Ground Floor
14	First Floor
15	Mumty
16	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :
17	1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
18	Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources).
19	Ground Floor
20	First Floor
21	Mumty
22	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :
23	1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
24	Boring with hydraulic piling rigs with power units, Providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto the bottom of pile cap):
25	300 mm dia piles
26	Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge.
27	Single pile upto 50 tonne safe capacity
28	Initial test. ( Test load 2.5 times the safe capacity)
29	Routine test ( Test load 1.5 times the safe capacity)
30	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :
31	1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) COLUMN
32	Ground Floor
33	First Floor
34	Mumty
35	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:
36	Cement mortar 1:6 (1 cement : 6 coarse sand)
37	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:
38	Cement mortar 1:4 (1 cement : coarse sand)
39	Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources).
40	Providing and applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.
41	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :
42	Cement mortar 1:6 (1 cement : 6 coarse sand)
43	Ground Floor
44	First Floor
45	Mumty
46	Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.
47	Cement mortar 1:4 (1 cement :4 coarse sand)
48	Ground Floor
49	First Floor
50	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.
51	Thermo-Mechanically Treated bars of grade Fe-500D or more.
52	Ground Floor
53	First Floor
54	Mumty
55	15 mm cement plaster on rough side of single or half brick wall of mix :
56	1:4 (1 cement: 4 coarse sand)
57	15 mm cement plaster on rough side of single or half brick wall of mix :
58	1:6 (1 cement: 6 coarse sand)
59	Ground Floor
60	First Floor
61	Mumty
62	12 mm cement plaster of mix :
63	1:6 (1 cement: 6 coarse sand)
64	Ground Floor
65	First Floor
66	Mumty
67	Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections
68	Ground Floor
69	First Floor
70	Mumty
71	Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc.,., complete.
72	Ground Floor
73	First Floor
74	Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kgper sqm including pointing the joints with white cement mixed with pigment of matching shade complete.
75	Ground Floor
76	First Floor
77	Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.
78	Double charge vitrified tile polished finish of size
79	Size of Tile 600 x 600 mm
80	Ground Floor
81	First Floor
82	Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08%and conforming to IS: 15622, of approved brand & manufacturer in all colours and shade in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints(Payment for grouting of joints to be made separately).
83	Size of Tile 600x600 mm
84	Ground Floor
85	First Floor
86	Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.
87	Granite stone slab colour black, Cherry/Ruby red
88	Area of slab over 0.50 sqm
89	Ground Floor
90	First Floor
91	Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling & dressing & finishing the top smooth.
92	Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:
93	35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
94	Ground Floor
95	First Floor
96	Mumty
97	Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.
98	Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.
99	In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.
100	Ground Floor
101	First Floor
102	Mumty
103	Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, priming coat of approved steel primer, but excluding the cost of other fittings, glass panes complete all as per approved design, (sectional weight of only steel members shall be measured for payment).
104	Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)
105	Ground Floor
106	First Floor
107	Mumty
108	Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.
109	Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)
110	Ground Floor
111	First Floor
112	Mumty
113	Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.
114	Ground Floor
115	First Floor
116	Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer, of required shade and colour all complete :
117	New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre
118	Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade
119	New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)
120	Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
121	Ground Floor
122	First Floor
123	Mumty
124	Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.
125	Twin rubber stopper
126	Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :
127	250x16 mm
128	Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :
129	250x10 mm
130	200x10 mm
131	Providing and fixing aluminium handles ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :
132	125 mm
133	Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations:
134	(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.
135	(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.
136	(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge.
137	(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.
138	(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :
139	With average thickness of 120 mm and minimum thickness at khurra as 65 mm.
140	Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :
141	Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture
142	Ground Floor
143	First Floor
144	Mumty
145	Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :
146	Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture
147	Ground Floor
148	First Floor
149	Mumty
150	Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete with :
151	4.0 mm thick glass panes.
152	Ground Floor
153	First Floor
154	Mumty
155	Centering and shuttering including strutting, propping etc. and removal of form for :
156	Foundations, footings, bases of columns, etc. for mass concrete
157	Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick
158	Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick
159	Columns, Pillars, Piers, Abutments, Posts and Struts
160	Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
161	62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded Stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2(1 cement hardener mix: 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture\"s specifications. This includes cost of cement slurry, but excluding the cost of nosing of Steps etc. complete.
162	Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8m Iong complete as per standard design
163	Providing and laying water proofing treatment on roofs oi slabs by applying cement slurry mixed with water proofing cement compound consisting of applying;
164	(a) after surface preparation, first layer of slurry o Cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm.
165	(b) laying second layer of Fiber glass cloth when the first layer is still green. Overlaps Of joints of fiber cloth should not be less than 10 cm.
166	(c) third layer of 1.5 mm thickness consisting of slurry o cement @ 1.289 kg/sqm mixed with water proofing Cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around.
167	(d) fourth and final layer Of brick tiling with cement mortar which Will be paid for Separately)
168	For the purpose of measurement the entire treated surface will be measured.
169	Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.
170	Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.
171	Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.
172	Electric resistance or induction butt welded tubes.
173	Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
174	Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer\"s specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work
175	PLUMBERING WORK.
176	Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings andfixtures complete, including cutting and making good the walls and floors wherever required :
177	W.C. pan with ISI marked white solid plastic seat and lid
178	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:
179	White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap
180	Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :
181	One urinal basin with 5 litre white P.V.C. automatic flushing cistern
182	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
183	Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.
184	Semi rigid pipe
185	32 mm dia
186	40 mm dia
187	Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.
188	Providing and fixing toilet paper holder :
189	C.P. brass
190	Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.
191	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.
192	(i)Single socketed pipes.
193	110 mm diameter
194	Making khurras 45x45 cm with average minimum thickness of5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.
195	Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.
196	110 mm
197	Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.
198	Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall.
199	(internal work)
200	Exposed on wall
201	32 mm dia. nominal bore
202	Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :
203	32 mm diameter pipe
204	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall
205	25 mm nominal outer dia .Pipes.
206	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. :Concealed work, including cutting chases and making good the walls etc.
207	15 mm nominal outer dia .Pipes.
208	20 mm nominal outer dia .Pipes.
209	25 mm nominal outer dia .Pipes.
210	Providing and fixing uplasticised PVC connection pipe with brass unions :
211	45 cm length
212	15 mm nominal bore
213	Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931:
214	15 mm nominal bore.
215	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:
216	Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.
217	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :
218	25 mm nominal bore
219	32 mm nominal bore.
220	Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :
221	25 mm nominal bore
222	Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includesmaking necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately.
223	Supply and fixing of UPVC S.W.R. pipe nahni trap size 100x75, 110/90 mm confirming to IS-14735 self cleaning design fixed in PCC 1:2:4 and supply and fixing of 125 mm dia heavy duty CP brass jali.
224	Supply and fixing of UPVC S.W.R. Cowel confirming to IS-14735.
225	Size 75/90 mm
226	Size 110mm
227	Supply and fixing of brass Health Faucet with Braided 1 meter Flexible Hose
228	Size 75/90
229	Supply and fixing of UPVC S.W.R. pipe type-B confirming to IS-13592 including jointing the pipes with rubber ring lubricant and UPVC SWR cupler confirming to IS-14735. Also including excavation of treanches cutting of walls and holes and repairing the walls, floors and refilling the trenches as before with supply and cost of other fittlings such as elbow,bend,tee and y-tee, Cowel Including supply of all marerial labour and T&P. Required for proper completion of work.
230	75 mm O.D.
231	110 mm O.D.
232	Supply and fixing of UPVC S.W.R. pipe nahni trap size 100x75,110/90 mm confirming to IS-14735 self cleaning design fixed in PCC 1:2:4 and supply and fixing of 125 mm dia heavy duty CP brass jali.
233	ELECTRICAL.
234	Wiring for light point with 1.5 sq.mm FRLS PVC Insulated copper conductor single core cable in surface / recessed medium class PVC condult, with modular switch, modular plate, suitable Gl box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group C
235	Wiring for fan point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium clase PVC conduit, with modular switch, modular plate, sultable Gl box and earthing the point with 1.5 sq.mm. FRLS PVC Insulated copper conductor single core cable etc as required Group C
236	Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.
237	2X1.5 sq. mm + 1 X 1.5 sq. mm earth wire
238	2 X2.5 sq. mm + 1X2.5 sq. mm earth wire
239	2 X 4 sq. mm + 1 X 4 sq. mm earth wire
240	2 X 6 sq. mm + 1 X 6 sq. mm earth wire
241	2 X 10 sq. mm + 1 X 6 sq. mm earth wire
242	4 X 10 sq. mm + 2X6 sq. mm earth wire
243	4 X 16 sq. mm + 2 X 6 sq. mm earth wire
244	Supplying and drawing following pair 0.5 sqmm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.
245	2 Pair
246	Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
247	Supplying and fixing of following sizes of medium class PVC conduit along with accessories in recess including cutting the wall and making good the same in case of recessed conduit as required.
248	25mm
249	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
250	Telephone socket outlet
251	TV antenna socket outlet
252	Bell push
253	Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
254	Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.
255	Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
256	Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
257	Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.
258	Supplying and fixing call bell/ buzzer suitable for single phase, V, complete as required.
259	Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (up to 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.
260	Numbering of ceiling fan/ exhaust fan/ fluorescent fittings as required.
261	Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.
262	Up to 450 mm sweep
263	Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.
264	Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).
265	Providing and fixing circular/Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73mm height, top lid of 1.5 mm thick MS DSR-sheet with its top surface hacked for proper bondine top lid shall be screwed into the cast iron/MS sheet box by means of 3.3 mm dia round headed screwed. one loc at the conrners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing
266	Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.
267	DISTRIBUTION BOARD, MCB\"S & ISOLATORS :
268	Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.
269	100A, 30KA FPMCCB
270	125A 36 KA, FPMCCB
271	Supplying and fixing following way, single pole and neutral sheet steel, MCB distribution board, 240 V on surface/recess complete with, tinned copper busbar, neutral busbar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (But without MCB/RCCB/Isolators).
272	8 way Double Door
273	Supplying and fixing following way, Horizontal type three pole and neutral MCB distribution board, 415 volts on surface /recess complete with, tinned copper busbar, neutral busbar, earth bar, din bar. Interconnections, powder painted including earthing etc. as required (But without MCB/RCCB/Isolators).
274	4 way (4+12)Double Door
275	6 way (4+18)Double Door
276	Supplying and fixing following way, surface/recess mounting vertical type 415V, TPN MCB distribution board, on steel sheet, dust protected, duly power painted, inclusive of 200 A tinned copper busbar. common neutral link, earth bar, din bar, for mounting MCBs (But without MCBs and incomer) as required(Note:vertical type MCB TPDB is normally used where 3 phase outles are required.)
277	4 way (4+12)Double Door
278	Supplying and fixing 5 amps. to 32 amps. rating, 240 volts \"C\" series, miniature circuit breaker (MCE suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
279	single Pole
280	Supplying and fixing single pole, blanking plate in the existing MCB DB complete etc. as required.
281	Supply and fixing 20 amp, 240 volts, SPN industrial Type, socket outlet With 2 pole and earth metal enclosed plug top along with 20 amp. C series SPMCB in sheet steel encosure, on surface or in recess with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.
282	Providing and fixing M.V. danger notice plate of 200 mmx150 mm, made of mild steel, at least 2 mm thick, and viterous enameled white on both sides, and with incription in single red colour on front side as required.
283	Supplying and fixing Cable End Box (Loose Wire Box) suitable for following triple pole and neutral, sheet steel, MCB distribution borad, 415 Volts, on surface/recess, complete with testing commissoning ect. as required.
284	For 4 way, Double Door TPNMCBDB
285	For 6 way, Double Door TPNMCBDB
286	Supply and installing of following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, jointed with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.
287	450mm width x 62.5mm depth x 2.0mm thickness
288	Earthing with GI earth pipe, 600 mm X 600 mm X 6 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/cock and salt as required.
289	Supplying and Laying of 25 mm X 3 mm G.I strip at 0.50 metre below ground as strip earth electrode. including connection / terminating with nut, bolt, spring, washer etc. as required.( jointing shall be done by overlapping and with 2 sets of G.L. nut bolt & spring washer spaced at 50mm)
290	Providing & fixing 6 SWG dia G.1. on surface or in recess for loop earthing as required.
291	Supplying & making end termination with brass compression gland and aluminium lugs for the following size of PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
292	2 X 6 sqmm. (19mm)
293	3.5 X 25 sqmm. (28mm)
294	3.5 X 35 sqmm. (32mm)
295	3.5 X 185 sqmm. (57mm)
296	Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.L. fittings including trenching (75 cm deep) and refilling etc as required.
297	100 mm Dia
298	Supplying & laying of following size DWC HDPE pipe ISI marked alongwith all accessories like socket, bend, couplers etc. confirming to IS: 14930 Part-Il complete with fitting, cutting & jointing etc, direct in ground (75cm below ground level) including excavation & refilling the trench but excluding sand cushioning & protective covering etc. as required.
299	90 mm dia (OD-90 mm & ID-76 mm nominal)
300	Supplying and embedding following dia G.I. pipe (medium class) in pole collar/ foundation (during casting) for cable entry including bending the pipe to the required shape complete as required.
301	40 mm Dia
302	Supplying and drawing following size of FRLS PVC insulated copper conductor, single core cable in existing surface/ recessed medium class PVC conduit as required.
303	3X2.5 sqmm
304	Supplying and laying of aluminium conductor PVC insulated armoured served sheathed cable 1100 volts grade at the depth of 750 mm bellow ground level over a cushion of 75 mm thick sand all around and protected with burnt bricks on side and on top as directed by Engineer-Incharge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.
305	6Sqmm 2Core
306	25 sqmm 3.5 Core
307	Supply & fixing of 7 mtr G.I. Octagonal Pole of approved make (top dia 70mm, Bottom dia 130 mm and base plate 12mm thik) having 3mm thikness with Single Arm bracket (1 Mtr length) on 1:2:4 RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and Required T&P completee in all respect.
308	Supply and fixing of LED Tube Light with heavy Duty Metal Box type Tube Light Fitting 1x22 watt suitable for upto 1x22 watt LED Polycarbonate tube light complete Including tube suitable for both surface & suspended complete in all respect.
309	2620 system lumens,with fully covered diffuser type>120 lm/w PF>.95,THD<10%, CRI>80, sheet thickness min 0.8mm, Tube with aluminium heat sink, >300V over voltage protection, 2.5 KV internal Surge protection, with 5 years Warrantee.CAT.-AAA
310	Supply and fixing of LED Street light Fitting with mandatory driver set having die cast aluminium body with toughend glass/UV stabilised PC cover and lences suitable for 75 watt to 90 watt and Confirming to IP 66, and IK07 and above protection having Company LOGO Engraved complete in all respects including Labour
311	9000-10800 system lumens, High Power LED with Lenses, 120 lm/W, PF>.95, THD<10%, at full load, CRI>70, Potted driver set in Metal housing(not circuitory) Phase to phase protection at 440V & >300V auto cut and re-start feature, 4 KV internal Surge protection with 5 years Warrantee.CAT.-AAA
312	Supply, Installation, Testing and Commissioning of L.T. Panel vermin proof floor mounting, M.S. Channel Base with bottom and Fabricated out of 2.0/1.6 mm thik CRCA sheet steel painted with powder coated paint of shade as per the direction of Engineer In charge after proper sheet treatment process of sheet steel. The bus bar of panel shall be electrical grade high conductive alluminium alloy of appropriate cross section as per the rating. The main busbar shall be run throughout the panel of rating as main incomer rating. The Bus Bar shall be supported by non hygroscopic SMC/DMC Bus bar suports which shall be mounted on proper interval to ensure the bear the jerks of suport of short cuircuit of 50kA for panels having ACB as Incomer & 36 kA for panels having MCCB Incomers. Panel shall be constructed in fully Segregated Compartment Design for each Feeder as per 3b construction Format. The panel shall be completed in all respect as per IS 8623 Part 2 & 3. There shall be Seperated metering Component for Incomer metts. on the Cclamps with EPD
313	All Incomer Feeders shall be provided with Multifunctional metering along with phase Indicating lights and other associated components such as CT control MCB Terminal Blocks etc. and all outgoing Feeders 100 A & above shall be provided with 3 phase Ammeter along with phase Indicating lights and other associates components such as CT control MCB Terminal Blocks etc. The feeder above shall be provided ac accommodated all measuring instrument shall be digital type & all indicating lights ahall be LED type. Wiring shall be done from 1100V Grade PVC Insulated copper flexible wire. All ACB shall be electricaly operated Draw out Type with microprosser based O/L, S/C & E/F Release off Breking/withstand capacity(ICU/ICs/lcw) 50 kA or more. All MCCB shall be thermal magnetics/microprossor with O/L & S/C protection along with required Spreders Extended rotary handle with pad locking facility of bracking capacity(ICU/ICS) 36 kA or more All MCB shall be Thermal 10kA \"C\"Curve Cubical type switch board shall be Cat-A and B only.
314	L.T. PANEL
315	250 Amp. 4P MCCB-1No
316	Cat. B Panel Cubicale Type
317	Metering
318	One (1) No. (0-500V) 96 x 96 Sqmm voltmeter with control fuse & selector switch.
319	One (1) No. (0-250) 96 x 96 Sqmm CT operated Ammeter with selector switch, CTs etc.
320	One (1) Set of Phase Indication Lamp.
321	Bus Bar:
322	One (1) No.320 A. TPN aluminimum bus bar of suitable length.
323	Outgoing
324	Phase indication lamps on each outgoing to be provided
325	125 Amp. 4P MCCB-2 No.
326	100 Amp. 4P MCCB-1 No.
327	63 Amp. 4P MCB-1 No.
328	40 Amp. 4P MCB-2 No.
329	32 Amp. SP MCB-1 No.
330	100 Amp. 4P MCCB-1 No.-Spare
331	63 Amp. 4P MCB-1 No.-Spare
332	40 Amp. 4P MCB-1 No.-Spare
333	OR outgoing as per site requirment(AS/SLD)
334	LT. FEEDER PILLER-LOC ON SITE
335	Supplying assembling erecting connecting, testing and commissioning of feeder pillar with over voltage and under voltage relay with auto re-setting, manufactured using 1.9/1.6 mm thick CRCA sheet steel with power coated paint double door (front operated)with canopy base channel and cable gland entry from bottom for cable using, suitable alluminium busbar with provision of incoming & outgoing MCCB/MCB of L&T/Schneider/GE/ABB or Eq. make. Installation of feeder pillar of suitable c.c foundation etc complete in all respect.
336	Incoming:
337	1No. Of 250 Amps 4P MCCB of 36 KA service breaking capacity and 250 Amp trip setting.
338	Metering: Voltmeter, Ammeter, Indication
339	Bus Bar:
340	1 Set of 320 Amps TPN Aluminium Bus Bars of suitable length and of cross section. Bus bar shall be insulated by heat shrinkable sleaves & clip on shrouds for joints. Bus bar shall be designed to with stand a fault level of 36 KA at 415 volts.
341	3Nos. Phase indicating lamp each lamp shall have one toggle switch.
342	Outgoing:
343	Phase indication lamps on each outgoing to be provided.
344	250Amp 4P MCCB (36kA)-1 Nos.
345	Supply & Fixing of 1X17 W mirror light complete in all respects. Make-Philips or Eq
346	Supply of AC 230/250 Volts, 50 Hz 55w 1400 rpm exhaust fans including providing nuts, bolts, mounting frame and other accessories including connections etc. complete as required.Make: Havells-STANDARD Refresh Air-SPS
347	300mm sweep
348	Supply and fixing following rateing four pole, 415 V, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required.
349	40 A,4P MCB-Bracking Capacity-10 kA, C-Curve-Make-Havells
350	63 A,4P MCB-Bracking Capacity-10 kA, C-Curve-Make-Havells
351	S/f of 10/20 pair Junction Boxes for Floors and building with Krone connectors, with connection and punching of same
352	Supply of 12 W LED BULB complete in all respect. Make-Philips or Eq
353	Supply of LED Tube Light with batten suitable for up to 1X20 watt LED tube light complete including tube etc. on surface/Pendent complete in all respect.Make-Philips or Eq
354	EXT. WATER SUPPLY.
355	Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated soil & then returning the soil as required,
356	in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m.
357	Pipes, cables etc. not exceeding 80mm dia.
358	Providing & fixing G.l. pipes complete with G.I. fittings including trenching and refilling etc.
359	External work
360	32mm nominal bore.
361	50mm nominal bore.
362	Providing & fixing sand of grading zone V or coaser grade alround the G.I. Pipes in external work.
363	32 mm diameter pipe
364	50 mm diameter pipe
365	Providing and fixing gate valve (with cap complete with bolts, nuts, rubber insertion etc.
366	32 mm nominal bore
367	50 mm nominal bore
368	Constructing masonry Chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement :4 coarse sand ) for sluice valve, with Cl. surface box 100mm top diameter, 160mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as er standard design :
369	With F.P.S. bricks
370	Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :
371	25 to 40 mm dia nominal bore
372	50 to 80 mm dia nominal bore
373	RAIN WATER HARVESTING.
374	Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over Areas (exceeding 30cm in depth. 1.5min width as well as on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatlydressed.
375	In all kind of soil upto 1.5m depth
376	In all kind of soil upto 1.5m to 3.0m depth
377	In all kind of soil upto 3.0m to 4.5m. depth
378	In all kind of soil upto 4.5m to 6.0m. depth
379	Providing and laying in position cement concrete of specified grade excluding the ccost of centering and shuttering -All work up to plinth level:
380	1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)
381	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:
382	Cement mortar 1:4 (1 cement : 4 coarse sand
383	Reinforced cement concrete work In beams, suspended floors, roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, bands plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement :1.5 coarse sand :3 graded stone aggregate 20mm nominal size)
384	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.
385	Mild steel and Medium Tensile steel bars.
386	Centring and shuttering including struting , proping etc and removal o form for :
387	Suspended floors, roofs, landings, balconies and access platform.
388	15mm cement plaster on rough side of single or half brick wall mix
389	1:4 1 cement : 4 coarse sand)
390	Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design:
391	With 20x20mm square bar
392	Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality
393	M.D. -10- Circular shape 500mm internal diameter
394	Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-incharge, upto 90 metre depth below ground level.
395	Drilling of 300mm dia bore hole manually
396	Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in charge.
397	150 mm nominal size dia
398	Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer- in-charge.
399	Supplying, filling, spreading & leveling gravels of size range 5 mm to 10mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer- in-charge
400	Supplying filling, spreading & leveling coarse sand of size range 1.5 mm to 2mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge.
401	Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/medium/coarse, in required grading & size as per actual requirement, all complete as per direction of Engineer-in-charge.
402	Earth work in excavation by (Hydraulic mechanical means excavator)/manual means over areas(exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.
403	In all kind of soil upto 1.5m depth
404	In all kind of soil upto 1.5m to 3.0m. depth
405	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work upto plinth level:
406	1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) .
407	Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:
408	Cement mortar (1 cement : 4 coarse sand )
409	Reinforced cement concrete work In beams, suspended floors, roofs having slope up to 152 landings, balconies, shelves, chajjas, lintels, bands plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, finishing and shuttering, reinforcement with 1:1.5:3 (1 cement :1.5 coarse sand :3 graded stone aggregate 20mm nominal size)
410	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.
411	Mild steel and Medium Tensile steel bars.
412	15mm cement plaster on rough side of single or half brick wall mix
413	1:4 1 cement : 4 coarse sand
414	Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design:
415	With 20x20mm square bar
416	Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality
417	M.D. -10- Circular shape 500mm internal diameter
418	Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated soil & then returning the soil as required,
419	in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m.
420	Pipes, cables etc. exceeding 80mm dia. But not exceeding 300 mm dia.
421	Providing, laying and joining glazed stone ware pipes class SP-I with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.
422	150mm diameter
423	200mm diameter
424	Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround S.W. Pipes including bed concrete as per standard design
425	150mm diameter S.W. Pipe
426	200mm diameter S.W. Pipe
427	Constructing brick masonry manhole with 75 class designation F.P.S. bricks in cement mortar 1:4 (1 cement : 4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand: 4graded stone aggregate 20mm nominal size); foundation concrete 1:4:8 mix
428	(1 cement :4 coarse sand: 8 graded stone aggregate 40mm nominal size) inside plasstering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4
429	(1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design
430	a) Inside size 60x60 cm & 60 cm deep including C.I. cover with frame (light duty) total wt. of cover & frame to be not less than 38 Kg (wt. of cover 23 Kg & wt. of frame 15 kg.
431	FIRE FIGHTING.
432	(A) Supplying, Installation, Testing & Commissioning of Electric driven terrace pump suitable for automatic operation and consisting of following complete in all respects, as required (Terrace Pump)
433	(B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal confirming to IS 1520
434	(C) Suitable HP Squirrel cage indution motor, TEFC type suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-\"F\" insulation, confirming to IS-325.
435	(D) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.
436	(E) Suitable cement concrete foundation duly plastered with anti vibration pads.
437	450 Ipm at 35 m head
438	Providing, laying, testing & Commissioning of \"C\" class heavy duty MS pipe confirming to IS 3589/IS1239 inculding welding, fittings like elbows,tees, langes,tapers,nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of syntetic enamel paint of required shade complete as required:
439	25 mm dia
440	100 mm dia
441	Supplying & fixing single headed internal yard hydrant valve with Instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel, ISI marked, confirming to IS 5290(type A) with blank Gunmetal/Stainless Steel cap and chain as required:
442	Single headed Gunmetal
443	Supplying, fixing, testing & commission of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confirming to IS 13095 of following sizes as required:
444	100 mm dia
445	Supplying & fixing orifice plate made out of 6 mm thick stainless steel(grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required
446	Providing, installation, testing and commission of non-return valve of following sizes confirming to 15. 5312 complete with rubber gaskets Gl bolts, nuts, washers etc as required:
447	100 mm dia
448	Supplying & fixing 63 mm dia, 15m long RRL hose pipe with 63 mm dia male and female couplings duly bound with Gl wire, rivets etc. confirming to IS 636(type-A) as required:
449	Gun Metal
450	Supplying & fixing First-aid hose Reel with MS construction spray painted in post office red.conforming to IS 884 complete with the following as required.
451	20 mm nominal internal dia water hose thermoplastic(Textile reinforced) type-2 as per IS:12585
452	20 mm nominal internal dia gun metal globe valve & nozzle.
453	Drum and brackets for fixing the equipments on wall.
454	Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.
455	30 m
456	Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle confirming to 15:903 suitable for instantaneous connection to interconnect hos pipe coupling as required.
457	Gun Metal
458	Supplying & fixing air vessel made out of 250 mm dia,8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.
459	Providing & fixing of pressure switch in M.S. 19.12 pipeline including connection etc as required
460	Supplying, installation, testing & commissioning uf Manual call Boxes of MS constuction in surface/recess with stainless steel chain & bammer assembly complete with glass and push button etc, as required
461	Supplying installation, testing & commissioning fire alarm sounder with facility to make announcement mounted in M.S. box(16 SWG) with hinged cover plate & suitable for operation with amplifier l/c line matching trasformer etc. complete as required.
462	Supplying installation, testing & commissioning talk back slave station in surface/recess suitable for operation on simplex mode complete with P.T.T. knob & speaker/microphone cenclosed in a M.S. box(16 SWG)/ABS box with break glass in front etc. complete as required
463	Supplying & laying of 2X1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.
464	Supplying & laying 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required.
465	Supply and fixing of following sizes of medium class PVC conduit alongwith the accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required:
466	25 mm
467	Supplying, Installation, testing & commissioning of main control and indicating panel made out SWG MS sheet to accommodate the following items duly powder coated in approved colour with louvers for ventilation, locking arrangement, audio and visual indication for fire alarm and public address system, monitoring system including connections, interconnections etc complete as required.
468	100 Watt amplifier racks suitable for operation on 230V AC/24VDC supply confirming to IEC-268 3 complete with all accessories as required-2 Nos. (one to act as standby)
469	Talk back master station with LED PTT(press to talk) push button for operation on 230V AC/24 V DC supply confirming to IEC-268 for simplex mode of operation/communication suitable for 20 Nos, talk back unit-1 set.
470	Annoucement control desk suitable for selection of different zones selectively and ON ALL CALL Switch with visual indication etc. complete as required-1 set
471	Amplifier change over switch for inter changingamplified-1 No.
472	Monitor panel for loudspeaker complete with output selector, ON/OFF switch fase, visual Indications etc. complete as required-1 No.
473	Gooseneck microphone with stand and ON/OFF switch-1 No.
474	Main ON/OFF switch,fuse indication lamps, DC and AC voltmeters & ammeters, terminal blockes etc. complete as required-1 set.
475	Battery charger trickle cum boost to take complete load of fire alarm & PA system complete with all accessories including providing & fixing of 2 nos 12 volt. 60 AH each sealed maintenance free bateries-1 set.
476	Providing, laying, testing & Commissioning of \"C class heavy duty MS pipe confirming to 15 3589/IS1239 inculding welding, fittings like elbows,tees, langes,tapers,nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of syntetic enamel paint of required shade complete as required:
477	80 mm dia
478	100 mm dia
479	Supplying & fixing single headed external yard hydrant valve with 1 No. 63 mm dia Instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, confirming to IS 5290(type A) with blank Gunmetal/Stainless Steel cap and chain as required:
480	Single headed Gunmetal
481	Supplying, fixing, testing & commission of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets confirming to IS 13095 of following sizes as required:
482	80 mm dia
483	100 mm dia
484	Providing, installation, testing and commission of non-return valve of following sizes confirming to 15: 5312 complete with rubber gaskets Gl bolts, nuts, washers etc as required:
485	100 mm dia
486	Supplying & fixing 63 mm dia, 15m long RRL hose pipe with 63 mm dia male and female couplings duly bound with Gl wire, rivets etc. confirming to 15 636(type-A) as required 116
487	Gun Metal
488	Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internall diameter size nozzle confirming to 15:903 suitable for instantaneous connection to interconnect hos pipe coupling as required Gun Metal
489	Gun Metal
490	Supplying & fixing of Fire brigade connection of cast iron body with gun metal male instantaneous inlet coupling complete with cap and chain as required. for suitable dia MS pipe connection conforming to IS 904 as required:
491	2 way-100 mm dia M.S. Pipe
492	Supply & fixing of fire extinguisher, ABC Type 6.00 kg. capacity(ISI Marked IS:15683 & TAC approved) comlete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.
493	Supply & fixing of CO2 type fire extinguisher. 6.5 kg. capacity (ISI Marked IS:2878 & TAC approved) comlete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.
494	Providing/Fixing of Fire Hose cabinet box made out of 18 gauge MS sheet including two coats of post office red paint over one coat of primer with 4 mm, thick glass door in front painted \"FIRE\" in red luminous paint. The size of the box should be 750 mm X 600 mm X 250 mm size capable of accommodating a pair of hose with coupling and nozzle. The box should be floor mounted type with railway coach lock arrangement and lever for opening the door after breaking the glass complete. Make: Standard/Lifeguard or EQ.
495	Providing & Fixing of 1.6 mm thick M.S / Door Frame, Door capable of accommodating fire Hose Reel, Landing Valve, Hose Pipes, fittings & accessories. The door shall have a front glass with lock and key arrangement & shall be painted with post office red colour (approval shall be taken on the basis of submitted sample before ordering).(Liasioing with civil contractor for making Recessed type mansoary box (by civil contractor).
496	Supplying and fixing of Self Glow Exit signage for stairs and exits made out from not less than 4 mm of transparent acrylic sheet of 300 x 150 mm size with self illuminated plastic words of 100 mm height suspended from ceiling by means of M.S. chain or fixed of the walls as required and as directed at site.(MAKE: Agni Suraksha (ASES) /Securiton-aka/System Sensor)
497	Supplying and fixing of Fire man axe. Make: Agni Suraksha (ASES) or EQ
498	Supply, Installation, Testing and Commissioning of electronic siren with suitable audible range of 1 k.m. approximately 4 watt.complete in all respects. Make:- Agni Suraksha (ASES) or EQ.
499	Providing/Fixing of cubical type floor mounted Fire pump control panel fabricated from 16 G M.S. sheet duly powder coated finish of approved shade and comprising of:Incomer:-a) 63 amp 4 Pole MCCB, 50Hz with breaking capacity 10KW.b)One Volt meter (0-500 V) with selector switch.c) Ammeter (0-63 Amps.) with selector switch & CT\"s. - 1 Setd) Set of 3 phase indication lamps - 1 Set e)Set of Al bus bar 200 Amp 4 strip- 1 Set Selector switch for local/remote, auto/manual/off operation ON/OFF indication lamp etc. - 1 Set
500	Outgoing:-1 x 63 Amps FP MCCB (25 KA) with Suitable HP fully automatic Star/Delta Starter with over load protection, current sensing type single phase preventor complete with all accessories and internal wiring required for automatic operation.

Also Visit

Tenders

Uttar Pradesh Tenders

Construction Tenders

Building Construction Tenders

Building Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Work Of Class Room Block, Guard Room, Toilet Block And Cycle Stand Shed At Govt. Girls Degree Gollege, Roberts Ganj District-Sonbhadra., Robertsganj-Uttar Pradesh

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Work Of Class Room Block, Guard Room, Toilet Block And Cycle Stand Shed At Govt. Girls Degree Gollege, Roberts Ganj District-Sonbhadra., Robertsganj-Uttar Pradesh

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us