|
| 1 | CIVIL WORKEarth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.(a) Depth of excavation not exceeding 1,500 mm. |
| 2 | (A) Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) |
| 3 | Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 4 | Anti termite treatment to bottom surface ( in case of masonry foundation and basements) and the sides ( upto a height of 300 mm. from bottom) of the excavation trenches with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight at the rate of 5 Litres per sq. m. area. The work shall be carried out as per specification described in 6.2.1. of code IS-6313 (part -II) 1981.( Mode of measurment will be the plan area of foundation treated.) |
| 5 | Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches. |
| 6 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor)(c) Steel shuttering or 9 to 12 mm thick approved quality ply board shutteringin any concrete work |
| 7 | (I) Cement concrete with graded stone ballast (40 mm size excluding shuttering(A) Pakur Variety (1:3:6)In ground floor |
| 8 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. |
| 9 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. |
| 10 | Brick work with 1st class bricks in cement mortar (1:6) as specifieda) In foundation upto Plinth level |
| 11 | Brick work with 1st class bricks in cement mortar (1:6) as specifiedb) In Superstructure at all roof |
| 12 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work)(a) With earth obtained from excavation offoundation. |
| 13 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4)gr floor |
| 14 | Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. In ground floor. 3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement). Using grey cement a) 35 mm. thick |
| 15 | Labour for Chipping of concrete surface before taking up Plastering work. |
| 16 | b) 15mm thk. Plaster with (1:6) cement sand mortar at all elevations (inside). |
| 17 | c) 10mm thk. Plaster with (1:4) cement sand mortar at all elevations. |
| 18 | Neat cement punning in plinth outside face,bunker floors, stair railings etc. at all elevations |
| 19 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] a) 20mm thk. Plaster with (1:6) cement sand mortar at all elevations (outside). |
| 20 | Supplying, fitting and fixing steel rolling shutter profile type with 18 B.G . of approved type steel latche section 75mm wide, fitted with coil wire spring to necessiate the fitting of required Nos. of C.I. Pulleys on heavy type solid drawn seamless steel tube complete with locking arrangements both inside and outside specially builtup side guide channels including providing a hood for the steel rolling shutter in the room, painting two coats of approved aluminium paint over a coat of red lead primer complete. |
| 21 | Collapsible gate with 40mm x 40mm x 6mm Tee as top and bottom guide rail, 20mm x 10mm x 2mm vertical channels 100mm apart in fully stretched position 20mm x 5mm M.S. flats as collapsible bracings properly rivetted and washered including 38mm steel rollers including locking arrangements, fitted and fixed in position with lugs set in cement concrete and including cutting necessary holes, chasing etc. in walls, floors etc. and making good damages complete. |
| 22 | Supplying, fitting, fixing steel window conforming to I.S. 1038- 1975 & manufactured from rolled steel sections conforming to I.S.S. with best quality glazing 3mm thick sheet glass, putty of approved make & brand, fixing lugs with cement concrete (1:2:4)including cutting holes to walls and mending good the damages with handle and peg & stayas directed complete.a) Openable type - |
| 23 | M.S.or W.I. Ornamental grill of approved design jointscontinuously welded with M.S, W.I. Flats and bars of windows,railing etc. fitted and fixed with necessary screws and lugs in groundfloor. (i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr. |
| 24 | Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). Sal : Local. |
| 25 | Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position butexcluding the cost of hinge and other fittings. In ground floor. 35mm thick shutters with 19mm thick panel of size 30 to 45 cm. Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak. |
| 26 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : With super gloss (hi-gloss) (a) On timber or plastered surface :(i) Two coats (with any shade except white) |
| 27 | (b) On steel or other metal surface : |
| 28 | (b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sandpapering etc. |
| 29 | (a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand |
| 30 | Acrylic Distemper to interior wall, ceiling with a coat of solvent basedinterior grade acrylic primer (as per manufacturer\"s specification)including cleaning and smoothning of surface.Two Coats |
| 31 | Applying Acrylic Emulsion Paint of approved make and brand on wallsand ceiling including sand papering in intermediate coats including putty(to be done under specific instruction of Superintending Engineer) :(Two coats) i) Standard Quality |
| 32 | Applying Exterior grade Acrylic primer of approved quality and brandon plastered or cencrete surface old or new surface to receivedecorative textured (matt finish) or smooth finish acrylic exterioremulsion paint including scraping and preparing the surface throughly,complete as per manufacturer\"s specification and as per direction of theEIC. Two Coats |
| 33 | Protective and Decorative Acrylic exterior emulsion paint of approvedquality, as per manufacturer\"s specification and as per direction ofEngineer-in-Charge to be applied over acrylic primer as required. Therate includes cost of material, labour, scaffolding and all incidentalcharges but excluding the cost of primer. In Ground floor (Two Coat) Premium 100% Acrylic Emulsion |
| 34 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete. A) UPVC Pipes: (ii) 110 mm. Dia. |
| 35 | B) UPVC Fittings: c) Bend (ii) 110 mm. Dia. |
| 36 | d) Shoe (ii) 110 mm. Dia. |
| 37 | Supplying and laying true to line and level Anti-Skid, Full Body, Homogeneous & Granular finish Vitrified Tiles conforming to IS:15622-2006 & IS 4457-2007 and testing shall be made in accordance with IS:13630 [Non- modular sizes for tiles with Skid resistance > 0.5, Mohr\"s hardness > 5.0, Staining resistance: Class-1, Water Absorption: E < 0.5%], MOR > 35 N/sq.mm in Internal area of building e.g. Toilet Block, Passage, Corridor, Accessible Open Terrace etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg./Sqm or using Polymerised Adhesive (6 mm thick layer applied directly over finished artificial stone floor/ Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per Sqm below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles/ epoxy grout materials of approved make asdirected and removal of wax coating of top surface of tiles with warm water andpolishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to themanufacturer\"s specification and direction of Engineer-in-Charge. (Whitecement, synthetic adhesive and grout material to be supplied by the contractor). a) In Ground Floor: Sizes-300 mm x300mm x10 mm with breaking strength >1200 N |
| 38 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.(B) Wall With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (a) Area of each tile upto 0.09 Sq.m (i) Coloured decorative |
| 39 | Providing and fixing PVC Door Frame of size 50x47mm with a wall thickness of 5mm (± 0.2 mm) made out of single piece extruded PVC profile, with mitred cut joint sand joint with 2 nos. of PVC bracket of size 190 mm x 100 mm long arms of cross section size 35 mm x 15 mm & self driven self taping screws, the vertical door profiles to be reinforced with 40x20mm M.S. rectangular tube of 0.8 mm ,including providing EPDM rubber gasket weather seal throughout the frame, including jointing 5 mm PVC frame strip with PVC solvent cement on the back of the profile. The doorframe to be fixed to the wall using 8 x100mm long anchor fasteners complete, all as per manufacturer‟s specification and direction ofEngineer -in- charge. |
| 40 | PVC Door Shutter-30 mm thick: Supplying fitting and fixing P.V.C. door shutter of approved quality & shade in position, the style & rail of the P.V.C. door shutter will be made of rigid P.V.C. multicavity hollow chamber of 59 mm x30 mm section with 2.0 mm (+/-0.2 mm) wall thickness.Horizontal & vertical section shall be fixed to each other by self tapping screws and 1 solid polymeric or M.S. galvanised tubular \"L\" shaped bracket 100mm x 200mm in each corner of the shutter frame for placing hinges. Polymer based multicavity hollow section of 120 mm x30mm with 2.0 mm (+/- 0.2mm) wall thickness will be fitted in the middle, reinforced by solid polymer bar of 200 mm long at both ends and screws from both sides as lock rail. The section frame will then be fitted in by PVC panels of size 100 mmx25 mm with wall thickness of 1.2 mm (+/- 0.2 mm) and 2 nos. of 6 mm dia bright rod will be inserted horizontally with both side check and nut system and stretches where fixing of hinges / hasp bolt / tower bolt / door ring are required to be strong enough to with stand wear and tear. The rate is inclusive of cost of all materials, labour, and hire of tools and plants and appliancesi/c carriage of all materialstaxes and all other incidental charges complete. |
| 41 | Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover (heavy type) of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 :1) to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C (1:1.5:3) bottom slab including supplying, fitting and fixing all necessry specials, fittings, S.W. tees, C.I. foot rest etc. including excavation earth in all sorts of soil, shoring, bailing out and pumping out water as necessary, ramming, dressing the bed and fefilling the sides of the tanks with earth, removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials.(ii) For 20 users with pakur varity (jsw/jspl/shyam/srmb etc..) |
| 42 | Construction of circular soak well 2.5 metre deep in all types of sandy soils with dry brick work upto 1.6 metre from the bottom having 150 mm intermediate cement brickwork (1:4) band all round and cement brick work (1:4) upto 0.90 metre from top with 20mm thick cement plastering (1:4) to inside face upto the depth of cement brickwork, 15mm thick cement plaster (1:4) on outer face from top of the well upto G.L. and 6 mm thick cement plaster (1:4) on top of the R.C.C. cover slab including fillingbottom 1.00 metre of inside of the well with brick metal (50 mm to 63 mm size) including R.C.C. cover slab of 100 mm thick with cement conc (1:1.5:3) with stone chips with necessary reinforcement and shuttering including one 560 mm dia. R.C.C. manhole cover (heavy type)of approved make supplied, fitted and fixed in the cover slab with necessary fittings, making nacessary arrangements for pipe connections, excavation of well including shoring, dewatering and removing the exess earth from the premises as per direction complete in all respect with all costs of labour and materials. With 250 mm thick dry brick work and 250 mm thick cement brick work (1:6) and1.00m inside dia. (jsw/jspl/shyam/ssl etc..) |
| 43 | 40 mm. thick damp proof course with cement concrete (1:1.5:3) (with graded stone chips 20 mm nominal size) with water proofing compound of approved brand @ 0.2% weightof cement including cost of materials over two coats of non toxic acrylic polymer modified cementitious waterproofing slurry coat complete [cost of water proofing compound and non toxic paint to be paid seperately) for underground waterretaining structures. |
| 44 | Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composit door, sliding &casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - In- Charge. (Payment will be made on finished length of the work). (A) In 10-12 Micron thickness Annodizing film I) Natural whitea) 2- track sliding windowi) Bottom frame |
| 45 | Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composit door, sliding &casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - In-Charge. (Payment will be made on finished length of the work). (A) In 10-12 Micron thickness Annodizing film I) Natural whitea) 2- track sliding windowii) Top and side frame. |
| 46 | Labour charge for fabrication and installation of composite door,window, partitions made from annodized extruded alloy aluminium sections for the following units:-(A) Glazed aluminium sliding windows made of extruded and annodized alloy aluminium sectios, fabrications, including cutting to proper shapeand size, drilling and aligning of window shutter frame fitted with in built locking arrangements, sliding rollers and other necessary fittings, fixture, adhesives and joineries along with extruded neoprine or EPDMgasketing in between window frame and masonry work (walls, column,beam.lintels etc.) as well as between glass and shutter frame for fixing glass and Polysulphide sealant and in between shutter and window frame where necessary including cutting to requisite size and fixing glass as per drawing, specification and direction of EIC. The rate includes the hire charge of all tools and plants, including allincidental charges, adhesive, joineries such as screw, cleat angle etc. but excluding the cost of extruded aluminium sections, glass, neoprene /EPDM gasket, locking arrangement and rollers. i ) 2 track sliding window. |
| 47 | Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987.ii) 4mm thick coloured / tinted / smoke glass. |
| 48 | Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc. With \"S\" trap |
| 49 | Supplying fitting and fixing 10 litre porcelain low down cistern of approved make with either side or bottom inlet, side over flow, brackets complete with all internal fittingsi) white |
| 50 | Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps completeii) C. P. Flush Pipe |
| 51 | Supplying fitting & fixing Flat Back Urinal in white glazed vitreous chinaware of approved make including waste connection etc. as necessary complete as directed - 470mmx280mmx340mm. |
| 52 | Supplying, fitting and fixing urinal flush pipe fittings of approved brand(c) C.P. urinal flush pipe fittings range of three |
| 53 | Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separatepayment will be made for accesories, specials. Payment for painting will be made seperately) (a) For Exposed Work PVC Pipes a) 25mm dia. Pipes |
| 54 | b) 15mm dia. Pipes |
| 55 | Supplying, fitting and fixing with cement jointing (3:1) salt glazed stoneware pipe including excavation of earth upto 1.50 metre depth in allsorts of soil both mixed or unmixed and refilling (but excluding concretingat bottom and sides). (iv) 100 mm |
| 56 | Supplying, fitting and fixing with cement jointing (3:1) with jute gasketsoaked in cement mortar. (a) Stoneware bend(iv) 100 mm |
| 57 | Supplying fitting & fixing stone ware T/Y junction with cement jointing (1:3) with jute gasket soaked in cement slurry in position complete as directed - 100mm dia.600mm long.(Single) |
| 58 | Supplying fitting & fixing C.P. towel rail with brackets complete - 25mm dia., 600mm long |
| 59 | Supplying, fitting and fixing soap holder..PTMT(Prayag or equivalent) |
| 60 | Supplying fitting & fixing Mirror 5.5mm thk. of approved make with silvering as per I.S.I. specification supported on fibre glass frame complete - 550mm x 400mm |
| 61 | Supply & installation of PVC water storage Tank of approved quality in position with closed top with lid as per direction complete - 500 Litres. |
| 62 | Wash Basin white glazed vitreous china best quality approved make wash basin with C.I brackets on 75 mmX 75mm wooden blocks ,C.P waist fittings 32mm dia, one approvedquality brass C.T. Piller cock of 15mm dia, C.P chain with rubber pluge of 30mm dia,approved quality P.V.C waist pipe with C.P. nut, 32mm dia ,900mm long approved quality P.V.Cconnection pipe with heavy brass C.P nutincluding mending good all damages and painting the brackets with two coarse of approved paint.550mmx400mm |
| 63 | Supplying, fitting and fixing bib cock or stop cock. Chromium plated Bib Cock long body with wall flange with aerator (Equivalent to Code No. 512 & Model - Tropical / umthing Special of ESSCO or similar brand) |
| 64 | Supplying fitting and fixing in position including all cost of materials, labour etc. as directed complete a) M.S. Clamp 40mm x 6mm x 125mm upto 170mm length |
| 65 | b) Iron butt hinges 75mm x 40mm x 1.12mm |
| 66 | c) Iron butt hinges 100mm x 58mm x 1.90mm |
| 67 | d) Anodised aluminium catch hook-150mm long |
| 68 | e) Anodised aluminium socket bolt-100mm long x 10mm dia. |
| 69 | g) Iron hasp bolt,16mm dia. - 300mm long |
| 70 | i) Iron door ring -75mm dia. |
| 71 | j) Wooden hinge cleat (sal) - 75mm long including 62mm long iron butt hinge |
| 72 | k) Wooden buffer block (sal) - 125mm long |
| 73 | ROADBox cutting or filling in Road embankment in all sorts of soil including spreading the spoils properly over the flank as necessary or on berm to approximate grade & camber and rolling the sub-grade with power roller to proper camber and grade as per direction and satisfaction of Engineer-in-charge including uprooting and removing plants and jungles when and where necessary |
| 74 | (b) For each additional Depth of 150mm and part therof |
| 75 | Extra for manual compaction of earth by rammers / hand roller in 250 mm layers including watering etc. if required. (Borrow pit measurement |
| 76 | Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity |
| 77 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade nd camber, applying and brooming requisite type of screening / binding materials to fill up the interstices of coarse aggregate, watering including lighting, guarding, barricading and making necessary earthen bundh of one metre width on each side and preparing the bed by necessary cutting or filling, including cost of all materials and hire and labour charges of all men and machinery and compacting to the required density, as per Clause 404 of Specifications for Road & Bridge Works of MoRT&H (5th Revision (ii) Grading-I Aggregate (63 mm to 45 mm) Using Stone Screening Type B (11.2 mm) |
| 78 | (iii) Grading-II Aggregate (53 mm to 22.4 mm) Using Stone Screening Type B (11.2 mm |
| 79 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. |
| 80 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor)(a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge. |
| 81 | ELECTRICAL WORKSElectrical:-Supplying and fixing 415V FP 63A Changeover switch with Sheet Steel enclosure on angle iron frame on wall with nuts bolts etc [HPL Make] as directrd by EIC. |
| 82 | Supplying and fixing Sheet steel 60/63 A Main Switches 415V TPN with fuse on L&N on flat iron frame on wall [HPL Make] as directrd by EIC. |
| 83 | Supplying & fixing sheet metal (16 SWG) Iron Clad 4 bars 415 V, 100/125 A Busbar chambers on angle iron frame on wall, incl. earthing attachment and painting as required – (As per Drawing no. 470 of PWD Specification Book – May 1991) [Approved make] |
| 84 | Supplying and fixing double door Horizontal 6 way TPN MCB Distribution board with IP-42/43 protection, on wall surface & mending good thedamages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment [Legrand Make] |
| 85 | Supplying and fixing 240/415 V 63A FP MCB Isolator on din rail of existing for TPN DBs and necessary connection. [Legrand Make] |
| 86 | Supplying and fixing 240/415 V 6-32A SP MCB of Breaking capacity 10kA & C characteristics on din rail of existing for TPN DBs and necessary connection. [Legrand Make] |
| 87 | Distribution wiring in 1.1 KV single core stranded \"FR\"PVC insulated & unsheathed copper wire [Approved make] in 20mm size PVC rigid conduit \"FR\" incl. necy. fittings as required (a) {2 x 4 sqmm + 1 x 2.5 sqmm} for [Approved make] [Approved make] |
| 88 | (b) {2 x 2.5 sqmm + 1 x 1.5 sqmm} for [Approved make] |
| 89 | (c) {3 x 1.5 sqmm} for[Approved make] |
| 90 | Distribution wiring in 2 x 22/0.3 (1.5 sqmm) single core stranded \"FR\" PVC insulated & unsheathed copper wire[Approved make] in 20mm size PVC rigid conduit \"FR\" [Approved make], with 1x22/0.3 (1.5 sqmm) single corestranded \"FR\" PVC insulated & unsheathed copper wire for ECC, to light/fan/call bell points with Piano Key type switch fixed on MS CRC sheet metal (16 SWG) switch board cumJB on wall complete with 2 no. suitable size “Ph & N” copper bar incl. bakelite/Perspex (wall matching color) top cover 3 mm thick and incl. 175mmx100mmx65mm inspection box,making earthing attachment, painting the MS box and mending good the damages to original finish (a) Average run 5 mtr |
| 91 | (b) Average run 8 mtr |
| 92 | (c) Average run 12 mtr |
| 93 | Distribution wiring in 1.1 KV grade 22/0.3 (1.5 sqmm) singlecore stranded \"FR\" PVC insulated & unsheathed copper wire(Brand approved by EIC) in 20mm size PVC rigid conduit \"FR\" (Precision make), with 1.1 KV grade 1 x 22/0.3 (1.5 sqmm) single core stranded \"FR\" PVC insulated & unsheathed copper wire as ECC, to 5A 3 pin flush type plug socket & Piano Key type switch fixed on MS CRC sheet metal (16 SWG) switch board cum JB on wall incl. bakelite/Perspex (wall matching color) top cover 3 mm thick and incl. painting the MS box and mending good the damages to original finish (a) On Board |
| 94 | Supply & Fixing 240 V, 20A, plug socket with separate 20 A Piano key type switch[Approved make] on sheetmetal switch board embedded in wall incl. S & F 150x100x65mm MS (16SWG) switch board and bakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required |
| 95 | Supply & Fixing 240 V, 3 nos. 6A, & 1 no. 20A plug socket with separate 3 nos. 6 A & 1 no. 20A Piano key type switch, indicator & 20A switch type SP MCB (Brand approved by EIC) on sheet metal switch board embedded in wall incl. S & F 240x200x65mm MS (16SWG) switch board andbakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required. |
| 96 | Supply & Fixing 240 V, 6A plug socket (Brand approvedby EIC), without switch & plug top, on existing sheet metal switch board with bakelite/perspex top cover by screws after making housing for plug by cutting bakelite/perspex top cover and making necy. connections with PVC wire and earth continuity wire etc. |
| 97 | Supply & Fixing 240 V, 25 A, Modular type starter [Approved make] with 25A Modular switch type DP MCB (CCurve) and 4 Module GI Modular type switch board with 4 Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. |
| 98 | Supply & Fixing 240 V, 25 A, 3 pin Modular type plug socket [Approved make], without plug top and switch with 2 Module GI Modular type switch board with top cover plate flushed in wall and making necy. connections with PVC Cu wire and earth continuity wire etc. |
| 99 | Supply & Fixing 240 V,25 A, 3 pin Modular type plug top with indicator [Approved make] & necy. Connections. |
| 100 | Supplying & Fixing 240 V AC/DC superior type Ding-Dong Call Bell (Anchor) on HW board incl. S&F HW board |
| 101 | Supplying & Fixing 240 V AC Buzzer (Ancho) on HW boardincl. S&F HW board |
| 102 | Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. Long By TATA-Medium GI pipe |
| 103 | Extra for providing masonery enclosure on the top of the earth electrode of overall |
| 104 | Extra for treatment of soil by using salt & charcoal or coke for plate electrode |
| 105 | Excavation of soil for installation of Earth Electrode and filling & ramming. For For Morrum Soil |
| 106 | Connecting the equipments GI pipe to earth busbar including S & F10 SWG. GI (Hot Dip) wire of size as below on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damages |
| 107 | Connecting the equipments to earth busbar including S & F 14 SWG. GI (Hot Dip) wire of size as below on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damages |
| 108 | Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required |
| 109 | Fixing only single/twin fluorescent light fitting suspended 25 cmbellow the ceiling with 2 No. 20 mm dia EI conduit (14 SWG)supports fixed with “L” type MS clamp whose one side fixed onceiling with sutable size 4 nos. fastener and other side connectedwith the conduit with suitable size of bolts and nuts incl. S&F EIconduit, “L” type (125mmx125mm) 6mm thick and 25mm with MSclamps and connecting the length of PVC insulated wire andmending good damages to original finish and painting etc. by2x24/0.20 mm (1.5sqmm.) flexible copper wire of 1.10 mt. length. |
| 110 | Extra for suspension exceeding 25 cm with S&F additional 2 no. 20 mm dia EI conduit (14 SWG) supports & necy. PVC insulated wire and painting etc. as required by 2x24/0.20 mm (1.5sqmm.) flexible copper wire of 1.10 mt. length. |
| 111 | Fixing only Floodlight fittings on top of masonary structure by 3 Nos. 10 mm dia x 87 mm long rag bolts, nuts & double washers complete either 37 mm x 10 mm MS flat support/or by other means as required |
| 112 | Fixing only bulk head ceiling fitting on wall /ceiling by screws etc. |
| 113 | Fixing only outdoor / street light type fluorescent light fitting or MV light fitting complete with all accessories to be fixed /projected from the wall of the building incl. making holes/providing clamping arrangement & necy. GI reducer as required. S&F 40 mm GI pipe (ISI-Medium) quality 1.5 mts. average length having suitable bend S&F necy. length of 1.5 sqmm PVC insulated single core stranded annealed copper wire and making connections as required and mending good damages to wall incl. painting etc. |
| 114 | Supplying & Fixing of Box type fan clamp of 150mm dia & 80mm depth made of 16 SWG CRCA sheet with one end duly sealed by cover, properly welded, incl. S&F 12mm dia 600mm long MS rod duly bent by heat treatment at the centre position of rod to grip fan bobbin properly, incl. binding the rod and fan box with reinforcement by 22 SWG steel binding wire, incl. supplying & covering the box with alkathene sheet, placed in order to prevent concrete from entering the box |
| 115 | Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc. incl. S&F connecting wire for down rod upto 30 cm incl. painting the rod with approved paint and making necessary connection as required by 2x1.5 sqmm flexible copper wire. |
| 116 | Extra for supplying additional wire for down rod & painting the rod exceeding 30 cm by 2x1.5 sqmm flexible copper wire |
| 117 | Supply & Fixing Socket type fan regulator (Step type) (Brand approved by EIC) on existing sheet metal switchboard with bakelite/perspex top cover by screw after making housing for regulator knob by cutting bakelite/perspex top cover incl. making necy. connectionsetc. |
| 118 | Fixing only cabin fan on wall/ceiling by S&F rag bolts, nuts & washers (6 mm dia x 62 mm long) or as reqd. incl. S&F 24/0.20 PVC insulated flexible copper wire 0.5 mt. length |
| 119 | Fixing only exhaust fan after making hole in wall and making good damages and smooth cement finish etc. as practicable as possible and providing necy. length of PVC insulated wire and making connection for exhaust of following diameter 45 cm (18\") |
| 120 | Fixing only louver shutter/cowl on wall with necy. bolts & nuts (6 mm dia x 62 mm long) 45 cm (18\") |
| 121 | SUPPLY OF FITTINGS LIGHT and FANFIRE EXTINGUISHER:-Supplying & fixing 2x20W T8LED light with Batten fixture.CROMPTON MAKELED Batten (IGP162 LT8-162xT8) & LED Aluminium 20W T8 tube (LGT8-20-865-2) or equivqlent model of PHILIPS /BAJAJ / HAVELLS as per direction of EIC. |
| 122 | Supplying & fixing Centura Neo LED Flood Light 50 W 6500 K IP66 LED Flood light suitable for industrial area lighting.HAVELLS MAKE (LHEECNP7PB6J050) or equivqlent model of PHILIPS /BAJAJ / CROMPTON as per direction of EIC. |
| 123 | Supplying & fixing 10W LED Bulkhead light fixture.CROMPTON MAKE(CIS-306-10-57-SL-DP-NBK) or equivqlent model of PHILIPS /BAJAJ / HAVELLS as per direction of EIC. |
| 124 | Supplying & fixing Superb Street Light 50 W 6500 K IP65 LED Street Light. HAVELLS MAKE (LHETAVU7PA7J050) or equivqlent model of PHILIPS /BAJAJ /CROMPTON as per direction of EIC. |
| 125 | Supplying & fixing1400 mm sweep Ceiling Fan. HAVELLS MAKE (FHCSV1SBRN56) or equivqlent model ORIENT/ CROMPTON/USHA as per direction of EIC. |
| 126 | Supplying & fixing 400MM sweep Wall Fan (cabin fan). HAVELLS MAKE (FHWSW4SIVR16) or equivqlent model ORIENT/ CROMPTON/USHA as per direction of EIC. |
| 127 | Supplying & fixing 450MM sweep Exhaust Fan. HAVELLS MAKE (FHEHDSPGRY18) or equivqlent model ORIENT/ CROMPTON/USHA as per direction of EIC. |
| 128 | Supply,, Installation, Testing & Commissioning of 4.5Kg ISI marked carbon – di – oxide (CO2) fire extinguisher consisting of welded MS cylindrical body, squeeze, lever discharge valve, fitted with internal discharge tube, high pressure discharge hose, discharge nozzle, suspension bracket, fin |
| 129 | Supply,, Installation, Testing & Commissioning of 6.0Kg ISI marked ABC Dry powderextinguisher (Stored Presser Type) consisting of welded MS cylindrical body, squeeze, lever discharge valve, fitted with internal discharge tube, high pressure discharge hose, discharge nozzle, suspension brack. |
| 130 | Add 18% G.S.T. + 1% L.W.Cess |
