Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 15-05-2025 | Date Extension | Date | 21-05-2025 |
| Sl. No. | Item Description |
| 1 | Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by thedepartmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. |
| 2 | Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification. |
| 3 | Supplying and filling in foundation, basement, etc with filling M.sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. |
| 4 | Supplying and filling in foundation, basement, etc with crushed stone dust in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. |
| 5 | Supplying and filling in foundation, basement, etc conveyed earth in layers of not more than 15 cm thick well watered, rammed and consolidated with a lead of 5km including cost of earth, conveyance charges, loading charges etc. complete complying with standard specification and as directed by the departmental officers. |
| 6 | Cement Concrete 1:5:10 (One Cement, Five M.sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundationincluding dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete |
| 7 | Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oakjoists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete |
| 8 | Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about 90 cm centre to centre and supported by casuarina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete |
| 9 | For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc. |
| 10 | For plane surfaces such asrectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc. |
| 11 | Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part there of but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers. |
| 12 | Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/mᶾ and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of M.sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers.The coarse and fine aggregates to be used should comply with the requirements of IS Standards.(No separate payment will be made by the Department for the excess usage of materials). |
| 13 | In foundation and basement |
| 14 | In Ground floor |
| 15 | In First Floor |
| 16 | In Second Floor |
| 17 | Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification.(Contractor has to make his own arrangements for the supply of steel and binding wire) |
| 18 | Brick work inCement Mortar 1:3 (One Cement, Three M.sand) using best quality fly ash bricks of 230x110x70mm for foundation and basement including curing, etc., complete complying with standard specification. |
| 19 | For foundation and basement |
| 20 | Brick work inCement Mortar 1:5 (One Cement, Five M.sand) using best quality fly ash bricks of 230x110x70mm for foundation and basement including curing, etc., complete complying with standard specification. |
| 21 | Foundation & Basement |
| 22 | Brick work in Cement Mortar 1:6 (One Cement, Six M.sand) sing best quality fly ash bricks of 230x110x70mmfor foundation and basement including curing, etc., complete complying with standard specification. |
| 23 | Ground Floor |
| 24 | First Floor |
| 25 | Second Floor |
| 26 | Brick partition walls of 11.00cm thickness sing best quality fly ash bricks of 230x110x70mm in Cement Mortar 1:3 (One Cement and Three M.sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately) |
| 27 | In Ground Floor |
| 28 | In First Floor |
| 29 | Paving the floor with best quality Double Charged Vetrified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three M-M.sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification.(The make and brand of the tiles should be Johnson / Kajaria / Somany / Nitco / RAK which has to be got approved by Executive Engineer before use on works). |
| 30 | Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three M.sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification. |
| 31 | Flooring with Self Designed Colour ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three M.sand)base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification.(The make and brand of the tiles should be got approved by Executive Engineer before use on works) |
| 32 | Self Designed Colour Ceramic Tiles |
| 33 | Dadooing walls with Joint free rectified Colour designed digital print ceramic tiles, with borders, with size of 300mm x 600mm x 10mm and above setin Cement Mortar 1:2 (One Cement and Two M.sand) 20mm thick andpointing the joints with white cement mixed with colouring pigmentsat the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc,,complying with standard specification and as directed by thedepartmental officers. (The make and brand of the tiles should belike Johnson / Kajaria / Somany / Nitco / RAK or Equivalent whichhas to be got approved by Executive Engineer before use on works) |
| 34 | Dadooing with Joint free rectified Colour designed digital print ceramic tiles, with borders, with size of 300mm x 450mm x 8mm |
| 35 | Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three crushed stone M.sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works) |
| 36 | Supplying and fixing fine polished cuddapah slab of following 40mm thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct. |
| 37 | Plastering with Cement Mortar 1:5 (One Cement and five P.sand) 12mm thick including finsihing, curing, etc., complete in all floors complying with standard specification and as directed. |
| 38 | Supplying and applying of Two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothly with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing.The surface shall then be allowed to dry for atleast 48 hours.It shall then be M.sand papered (waterproof abrasive sheet) to give a smooth and even surface.Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then M.sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the departmental officers.(The rates are inclusive of hire charges for grinding machine with wheel, cost of M.sand paper (water proof abrasive sheet) cost of putty blade, labour charges for grinding the joints and M.sand papering, two coats of putty, scrapping the putty area to level the surface smooth, etc., complete). The putty should be got approved by the Executive Engineer before use on work. |
| 39 | Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three M.sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers |
| 40 | Plastering with Cement Mortar 1:3 (One Cement and Three P.sand) 20mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers. |
| 41 | Plain cement Concrete 1:2:4(one cement ,Two M.sand, four coarse aggregate )using 20mm jelly for wearing coat including laying, compacting ,finishing and curing,etc. Complete as per standard specification and as directed by the departmental officers. |
| 42 | Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of \"U\" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. |
| 43 | 110 mm dia |
| 44 | Supplying and fixingh CRCA pressed steel Box section 18 Gauge or1.25mm thick for Door frames including providing holes and fixing wooden blocks for fixing furniture and fittings with powder coated primer etc, complete. |
| 45 | Supplying and fixing door shutter of medium density fibre board of exterior grade and pre-laminated (on both side) 35mm thick confirmingto ISI 12406 / 1989 with 35x12mm T.W. lipping on all edges with necessary adhesive and CP screws complying with standard specification.The rate isinclusive of best quality varnish over a coat of bees waxing, suppling and fixing suitable wind appliancesetc. complete.Rate shall be inclusive of ost of allmaterials and labour charges for fixing the shutterswith RCC frames etc. complete. including cost of furniture fittings) The sample of materials and fittingsshould be got approved by the Exe.Engr. before useon works. |
| 46 | Single leaf |
| 47 | Double leaves |
| 48 | Supplying and fixing FRP door Sutter with FRP door frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost of holdfasts and solid core FRP shutter Panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., of sizes specified by Engineers. |
| 49 | Supplying, fabricating and fixing in position of aluminiumanosdised powder coated matt Sliding door half glazed and half PLB board 12mm thick, 5.5mm thk glazed door using section alu. Clips, double action springs , door closer, lock and glass including all materials , labour, power of following sizesfor frame and shutter with necessary accessories such as electrically controlled condition in accordance with sections ISI1868./1962 of anodic film thickness of not , if not less than 15 microns for all sections. The aluminium surface to be anodized with matt finish under rubber beeding rectangular aluminium box charges requireed for fabrication if necessary clipping , dismantling materials, holes in RCC column beams or masonry whereever with power drill to extent required and madegood to original condition after fixing etc., complete. All materials should be got approved by executive engineer before use on works. |
| 50 | Supplying and erecting pull and push type rolling shutter with ISI make of approved size and section using 18 GI sheet.The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc., Gear operated type (from 8 m2 to 12 m2 area) |
| 51 | Manufacturing, supplying and fixing of Steel Doorwith following specification.MS angle of size 40 x 40 x 6mm at 3.5 kg. / m used for outer frame and MS Angle of size 35 x 35 x 5mm at 2.6 kg. / m for the shutter frame.Stiffeners with 32 x 6mm at 1.5 kg. / m MS Flat is provided as the lock rail of the door and welded intact on both ends to the shutter frame.18G CR Sheets of best quality is laid as panel in the shutter frames.18 x 5mm at 0.70 kg. / m MS Flat is welded over the 32 x 6mm at 1.50 Kg. / m MS Flat on the rear side of the door, M.sandwitching the CR Sheet for rigidity. All members are given one coat of red oxide primer as directed by the departmental officers.The rate includes cost of all materials, labour charges, transportation, taxes and all other incidental charges, etc., complete, complying with standard specifications. (Single Leaf) |
| 52 | Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) windows of casemetn type (open) from the profile the size of outer frame 60mmx58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multichambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered wtih over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle, The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it shoudl not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames, The window should be got approved from the Executive Engineer before use on works. |
| 53 | Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations free pin headed glass 4mm thick should be provided in the louvers. The ventilator should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work |
| 54 | Manufacturing, Supplying and fixing in position of Steel Windows with the following specifications.Outer frames of Windows made of \"Z\" section F7D of size 33 x 25 x 3mm at 1.419 kg / m and mullion \"J\" Section (F4B) of size 46 x 25 x 3mm at 2.28 kg/m and shutter section of made of F7D of 33 x 25 x 3mm at 1.419 kg / m as specified in IS 7452 / 1990.Each openable shutter should not exceed a width of 600mm to enable separate operations and easy maintenance.at all the four corners of each shutters to the suitable length welded to the shutters, for holding the CR Sheets in position firmly.2 Numbers of sturdy hinges and one number of handle-cum-latch of special type made with 18 x 5mm MS Flats are revetted to the shutters at an appropriate height in Window. Suitable opening is left for its easy operation.A stopper square rod for handle is provided in the mullion section at suitable place to catch the Window handle.Each Window shutter having an adjustable stay made out of 18 x 5mm at 0.70 kg/m MS Flat of length 320mm with three adjustable position.A matching peg is provided in the outer frame of the Window at suitable place.. An MS square bar of 12mm size is welded to the inner face of the Window at an equal interval not exceeding 100mm edge to edge between them.All members are painted with one coat of anti-corrosive red oxide primer as directed by the departmental officers.All sections should be in confirmed with IS 7452 / 1990.The cost includes cost of all materials, labour charges and other incidental charges, etc., complete. |
| 55 | Three leaves |
| 56 | Fabrication, supply and fixing in position of \"N\" type ventilators using M.S. angle of size 25 x 25 x5 mm for frame and M.S. Flat of size 20 x 3 mm for fixing the weld mesh and using 25 x 22 x3 mm \"T\" section for frame glass.Special type of Hold fast welded to the frame of 45 degree inclined towards centre for wall and fxing the weldmesh 25mm square including cost of 3mm thick pinheaded glass panes for all panels and fixing the glass panels with necessary clips & putties with required bolts, nuts and washers and one coat of red oxide primer etc. including necessary dismantling, making holes in RCC columns, beams, masonry wherever necessary with power drill to the extend required and made good to the original conditions after fising as directed by the departmental officers. |
| 57 | Manufacturing supplying and fixing in position of teracotta jally 20x20x5cmthick approved quality and design in cement slurry including cost of materials labour curing lifting fixing in position etc, complete complying with standard specification and as directed by the departmental officers in all floors. |
| 58 | Supply and Installation of Ceramic writing Board of size 3.60 mx 1.20m made on steel core the long lasting porcelain is fused at temperatures up to 800 c. with this process a scratch and stain resistant surface is created and becomes smooth and erasing free of \"Ghost lines\" virtually maintenance free, this chalk board never acquires. \"chalking in\" and total cleaning is accomplished with clear water the writing surface will not crack peel even when solvents are use to remove crayon, paint or other foreign substances highly versatile, the entire writing area can become a display board with the help of magnetic buttons. The boards are made of 0.4mm ceramic on steel writing surface 9mm MDF, 0.2mm, GI sheet. The above three materials M.sandwiched with rubber based. |
| 59 | Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between.The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete.The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete |
| 60 | Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing.The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade.The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete |
| 61 | Supplying and fixing of M.S. grill of approved design for open courtyard, grill, grill work to doors and window openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including cutting the members, welding, grinding, one coat of priming coat using best approved quality red oxide primer, dismantling of walls /concrete if necessary, fixing and finishing the dismantled portion to original condition etc., complete complying with standard specification. |
| 62 | Supplying and fixing in position of Steel fibre reinforced cement concrete (SFRC)manhole / inspection chamber cover slab with following frame sizes including necessary labour charges for fixing the frame in position over the cement mortar base and finishing the joints etc. complete as directed. |
| 63 | Fabricating, Supplying and erection aA type iron Truss made up of ISA 9090 6mm Angle section for Tie member , ISA 8080 6mm Angle section for Rafter member,ISA 5050 6mm & ISA 4040 6mm Angle section for Web member. The slop ofRidge is in 1:5 ratio with the Wind speed of 200 kg/m2 and Considering the Spacing 6m and 12m span.The above mentioned Detailes are extracted from SP:38(S&T)-1987 code book. necessary holes are provided in the angle for connecting the vertical post. the special type truss may be erected on face of the vertical post in correct alignment of position used with hydralic power craneincluding cost of heavy type bolt, nut washers etc complete and including cutting, drilling, grinding, power consumption charges etc complete the iron members are painted with one coat of anticorrosive sincromate primer and two coat of best enamal paint, loading and unloading transportation charges and any other incidential charges., complete. |
| 64 | Fabricating, Supplying and erection a A type iron Truss made up of ISA 7070 6mm Angle section for Tie member , ISA 7070 6mm Angle section for Rafter member,ISA 5050 6mm & ISA 4040 6mm Angle section for Web member. The slop ofRidge is in 1:5 ratio with the Wind speed of 200 kg/m2 and Considering the Spacing 6m and span 9m. The above mentioned Detailes are extracted from SP:38(S&T)-1987 code book. necessary holes are provided in the angle for connecting the vertical post. the special type truss may be erected on face of the vertical post in correct alignment of position used with hydralic power crane of including cost of heavy type bolt, nut washers etc complete and including cutting, drilling, grinding, power consumption charges etc complete the iron members are painted with one coat of anticorrosive sincromate primer and two coat of best enamal paint, loading and unloading transportation charges and any other incisental charges., complete. |
| 65 | Supplying and fixing by drilling holes and not by puching for Roofing with pre painted Galvalum sheet of0.47mm thick of best approved quality with required size with curved shape and white ridge sheet with necessary bolts and nuts bitumen washers, including cutting the sheet to the required size found necessary during execution etc., Complete complying with standard specifications. [The sheet should be got approved by the Engineer incharge before use on works] |
| 66 | Manufacturig, supplying and fixing of purlin with new mild steel square tube purlin of size 50mm x 50mm x 40mm superior quality including cost of welding, finishing with two coat of synthetic enamel paint over a primer coat including cost of transportation, loading and unloading welding etc., complete. |
| 67 | Supplying and fixing in position white colourglazed Special delux model Glazed Cascade type (parryware/hindware/ equivalent wall mounted) European Water Closet of best quality and approved make with 100 mm \"P\" or \"S\" trap connecting with PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings...... |
| 68 | Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with \"P\" or \"S\" trap conforming to BIS with M.sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two M.sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers.(The water closet should be got approved by the Executive Engineer before use on works). |
| 69 | Supplying and fixing in position Indian make white glazed lipped mouth flat back urinal of best quality and approved make including dismantling masonry, if necessary and re-doing the same to original condition, etc., complete complying with standard specification. (The squatting urinal should be got approved by the Executive Engineer before use on works). |
| 70 | Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia \"B\" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylon connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. |
| 71 | Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks) |
| 72 | Supplying and fixing best approved best quality brass CP soap tray of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications.(The soap tray should be got approved by Executive Engineer before use on works). |
| 73 | Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works). |
| 74 | Supplying, laying and jointing UPVC pipes of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto etc., complete complying with standard specifications.The UPVC pipes shall be got approved by Executive Engineer before use on works.(Above Ground Level) (Internal Water supply) |
| 75 | 50 mm dia UPVC pipe - Below Ground Level |
| 76 | 40 mm dia UPVC Pipe - Above Ground Level |
| 77 | 25mm dia UPVC Pipe - Above Ground Level |
| 78 | Supplying UPVC Specials in water supply arrangements (both in internal and external water supply arrangements. |
| 79 | 50mm Dia UPVC Elbow |
| 80 | 50mm Dia UPVC Tee |
| 81 | 50mm Dia UPVC Bend |
| 82 | 50mm Dia UPVC Union |
| 83 | 40mm Dia UPVC Elbow |
| 84 | 40mm Dia UPVC Tee |
| 85 | 40mm Dia UPVC Bend |
| 86 | 40mm Dia UPVC Union |
| 87 | 25mm Dia UPVC Elbow |
| 88 | 25mm Dia UPVC Tee |
| 89 | 25mm Dia UPVC Bend |
| 90 | 25mm Dia UPVC Union |
| 91 | 50 x40 mm Dia UPVC Reducer |
| 92 | 25 x 20 mm Dia UPVC Reducer |
| 93 | 20 x 15mm Dia UPVC Reducer |
| 94 | Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements).The valves to be used on work shall be got approved by the Executive Engineer before use on work. |
| 95 | 50 mm Dia - Gate Valve |
| 96 | 40mm Dia - Gate Valve |
| 97 | 32mm Dia - Gate Valve |
| 98 | 25mm Dia - Gate Valve |
| 99 | Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications.(The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level |
| 100 | 160mm dia PVC soil / waste pipe |
| 101 | 110mm dia PVC soil / waste pipe |
| 102 | 75mm dia PVC soil / waste pipe |
| 103 | Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works). |
| 104 | 160mm Dia - Plain bend |
| 105 | 160mm Dia - Elbow |
| 106 | 160mm Dia - Tee |
| 107 | 110mm Dia- Plain bend |
| 108 | 110mm Dia- Elbow |
| 109 | 110mm Dia- Tee |
| 110 | 75mm Dia - Plain bend |
| 111 | 75mm Dia - Elbow |
| 112 | 75mm Dia - Tee |
| 113 | Supplying and fixing position CI Nahani Trap of size 100x75mm with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of M.sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three M.sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works) |
| 114 | Nahani Trap of size 100 x 75mm with stainless steel gratings |
| 115 | Supplying and fixing in position tap of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary.(Taps should be got approved by the Executive Engineer before use on the works) |
| 116 | 15mm dia CP Screw Down Tap |
| 117 | Swan neck tap |
| 118 | Supplying, laying and jointing glazed stone ware pipes of the following dia of approved quality with spigot and socket ends and fixing them in dry condition using spun yarn and cement including petty masonry shoring and strutting wherever found necessary and laying the pipe line in the alignment at the specified gradient and testing with necessary tools and plants, etc., and re-filling the trench with excavated earth and levelling the ground etc.,complete complying with standard specifications.(Earth work excavation, re-filling with excavated earth will be measured and paid separately). |
| 119 | 100 mm dia pipe |
| 120 | Supplying and fixing in position 100mm dia stoneware tee of approved best quality and provding leak proof joints with cement, spun yarn, etc., including dismantling the brick work and re-doing the dismantled portion to the original condition, etc., complete complying with standard specifications (The stoneware tee shall be got approved by the Executive Engineer before use on work) |
| 121 | Supplying and fixing PVC ventilating shaft of 110mm dia (having working pressure 4 kg. / sq.cm) with 3 metre height including cost of PVC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers |
| 122 | Supplying and filling following HBG stone jelly for dispersion trench including cost of jelly, filling charges etc. complete |
| 123 | 40mm HBG stone jelly |
| 124 | 20mm HBG stone jelly |
| 125 | Providing rain water arrangements by earthwork excavation in loose or hard soil to a depth of 90 cm and 100cm diameter and filled with 40 mm brick jelly to full depth and RCC well rings of 90 cm dia to adepth of 1.20 m and covering the top with precast slab of 75mm thick etc. complete |
| 126 | Providing Anti-termite treatment to soil adjacent and under building foundation, plinth periphery of the building by application of chemicals of IS 6313 Part I to IV in stages to suit the progress of work consist as per the detailed specification as below(Measurements taken for the plinth area for the purpose of payment) including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing, etc., complete and as directed by the departmental officers. |
| 127 | Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification |
| 128 | Painting the wall surface with Texture Finish Paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. |
| 129 | Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. |
| 130 | Drilling of borewells any where in kancheepuram and Tiruvallur district including transportion from one place to another in alluvial soil sedimentary strat of clay and M.sand stone shale pebbles, boulders, etc. by first taking a pilot bore of 150 mm dia and the enlarging to required diaby direct or reverse rotary mud circulation method, using fuel, labour drilling and water required for drilling at the site shown by the officers including construction of mud pit. |
| 131 | Reaming from 140mm/200mm dia pilot bore to 300mm dia bore as directed by the departmental officers upto 6m depth ending below GL |
| 132 | Supplying of 160 mm dia PVC pipe of 6 kg/cm2 without slot as weep holes of approved brand and quality for bore wells etc complete complying with standard specification and as directed by the departmental officers. |
| 133 | Supplying of 160 mm dia slotted PVC pipe of 6 kg/cm2 with slot as weep holes of approved brand and quality for bore wells etc complete complying with standard specification and as directed by the departmental officers |
| 134 | Labour charges for inserting 160mm dia PVC casing pipes assembly (with slot or without slots ) in the drilled hole including jointing the pipe with PVC coupler and with cement paste etc. complete |
| 135 | Charges for developing the borewell for entire depth with suitable air compressor of 300RPM capacity (minimum 8hrs) including transportation labour and fuel charges for compressor and directed by the departmental officers and conducting yield test by \"V\" notch method |
| 136 | Supplying and fixing of HDPE Hose of 40mm dia for Submersible pump including fixing etc complete complying with standard specification and as directed by the departmental officers. |
| 137 | Supplying and run of 2 of 7/20 PVC sheathed Aluminium cable with polythene wire 10 gauge stay wire etc complete complying with standard specification and as directed by the departmental officers. |
| 138 | Supplying and fixing of 3HP of approved brand Submersible Pump with accessories of starter, Main Switch, Panel Board etc. complete to suit the need (The pump ste should be got approved by the EE before supply) |
| 139 | Supplying and fixing of 2000 litres capacity PVC tank of approved quality and brand including fixing in position etc,. Complete. |
| 140 | Supplying and Fixing of Stainless steel Letters of approved size and colour. The colour treatment process is achieved with MRF colour coat and then the processed coloured layer is set into the kiln for theheat treatment process for the following sizes |
| 141 | Tamil Stainless Steel Letters 25cm (10”) |
| 142 | Emblem |
| 143 | Process of 5mm Epoxy flooring :- Providing and applying high performance Epoxy Flooring of JEMKON Make of 5mm thickness on concrete surface,and should be approved by EE which includes surface preparation throughly by grinding & cleaning all dirt, debris to achieve a sound surface, followed by a primer coat with Tech 24 of 0.1 mm by mixing base and hardener (as per manufacturer’s specification). It will be followed by a screed coat with Tech 60 of 4mm by mixing base & hardener & aggregates(as per manufacturer’s specification) & followed by application of Final Top coat with Tech SLE of 0.9 mm by mixing base , hardener , color paste & aggregates (as per manufacturer’s specification) complete as per specifications and as directed by Engineer-In-Charge. Total thickness will be 5 mm |
| 144 | Designing the Semi Unitised Structural Glazing System with open groove joint as per design intent, preparation of shop drawings for approval, supply, fabricating, erect as per approved shop drawings at all floor levels and all floor heights including conducting field test as per the test criteria set out in the particular specification (Metholodgy should be got approved by the Dept. Officials.) Design the framing system (i.e. male & Female frame) to support vision panels,pandrel panels either with glass or aluminium composite panel, openable, window panels on a continuous framing supported between floors. Also design the split framing unutilized glazing system in case of strip or punched windows with vision panel proposed with either insulated / Monolithic glass, groove width in the system both in horizontal and vertical shall not be more than 20mm. Glazing of panel shall be done only at factory at the controlled atmosphere. |
| 145 | GST @ 18% |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
