Tender For School Strengthening Works At Gsss Chirwa Block Badgaon Udaipur - Construction Of 1 Acrwith Verandah At Gsss Chirwa (Remaining Work) - PART A ( CIVIL WORK) BASED ON PWD BSR 2013 UDAIPUR CIRCLE & (Sanitary Work) Based on BSR PWD - 2013, Circle Udaipur & (Electric Work) Based on BSR PWD 2013, Jaipur Circle 2 Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.All kinds of soils 3 PCC in foundation :Providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level 1:4:8(1 cement:4 Coarse sand :8 graded stone aggregate 40 mm nominal size). 4 Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in cement mortat 1:6 (1-Cement: 6- Sand) 5 Providing and laying in position specified grade ofcement concrete forall RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix 6 Supply & stacking good earth at site complete including loading , unloading and transportation etc &Filling available excavated earth (excluding rock) in trenches plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead upto 50 Mtr. and lift upto 1.5 Mtr. 7 Brick masonary in foundation and super structure bricks of class designation 75 in Cement mortar 1:6 ( 1 cement : 6 coarse sand ) up to third storey with clayfly ash bricks 8 Stone Kharanja: Random rubble dry stone kharanja under floor 9 PCC:Providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering all work upto plinth level1:3:6(1 cement:3 Coarse sand :6 graded stone aggregate 20 mm nominal size).M 10 grade nominal mix 10 Lintel Beam : Providing and laying in position specified grade ofcement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcementfor Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.M20 grade Nominal Mix / Design Mix 11 Slab & Beams: Providing and laying in position specified grade ofcement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcementfor Beams, suspended floors, roofs, griders having slopes up to 15º, landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral staircases etc.M20 grade Nominal Mix / Design Mix 12 Providing and laying in position specified grade of cement concrete for RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement:3 coarse sand) and making good the joints and cost of plastisers (if required ) excluding the cost of centtering shuttering and reinforcement,M 20 grade nominal mix/ design mix. 13 Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement:3 coarse sand) and making good the joints and excluding the cost of centering shuttering and reinforcement for walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillers, piers, abutments, post and struts etc M 20 Grade Nominal Mix(With graded stone aggregate 20 mm nominal size) 14 Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for foundation, footings, strap beam, raft, base of column etc 15 Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for columns, pillers, posts,and struts etc 16 P/F reinforcement for RCC work including straightening,cutting, bending, placing in position and binding (including cost of binding wire)all complete upto floor five leveTMT bars (Conforming of relevent IS Code) 17 Providing and fixing M.S. sheet 1mm thickdouble leaf door shutter windows in angle iron frame35x35x5 mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint 18 Wire Gauge Supplying & fixing fixed wire Gauge to the Metal frame of rolled section by metal beading 20X3mm with suitable screw at not exceeding 150mm distance. 14 mesh X 24 Gauge 19 Guard Bars: Providing and fixing square bars or other flat welded to window/ventilators etc., Guard bar 12 x12mm 20 Polished Blue kota stone flooring skirting laid over 20mmthick base of CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete For area 2001 to 5000 sq. Cm 21 Internal Plaster : Plaster on new surface on wall in cement sand mortar 1:6 including raking of joints etc. complete fine finish: 12mm thick 22 External Plaster : Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finished 20 mm thick 23 Plaster(Ceiling): 6 mm thick cement plaster to ceiling of mix 1:3(1 cement: 3 fine sand) 24 Grading roof for water proofing treatment withwater proffing compound: Cement concrete 1: 2: 4 (1 cement: 2 Course sand: 4 Greded stone aggregate 20 mm nominal size) 25 Gola Providing gola 75mm x 75mm in cement concrete 1:2:4(1 cement: 2 coarse sand: 4 stoneaggregate 10 mm and down gauge) including finished with cement mortar 1:3(1 cement: 2 fine sand) as per standard design. 26 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade two or more coats on new work including preparation of base with primer, putty, lippy complete in all respect. 27 PANTING ON DOORS & WINDOWS:- Painting with syntheitic enamel paint of approved brand and manufacture in all shade to give an even shadenew steel work (2 or more coat on new work). 28 Copping: Providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls(any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, copping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering. M20 grade nominal Mix 1:1.5:3(1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size) 29 P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 110 mm dia 30 Pipe Clip110 mm dia 31 P&F T - iron / angel doors frames for doors window and ventilation of mild steel Tee-section, jionts mitred and welded with 15x3 mm lugs, 10cm long embedded in cement concrete blocks 15x10x10cm of 1:3:6 (1cement : 3 coarse sand :6 graded stone aggregate 20mm nominal size) or with wooden plug and screw or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer (40x40x5 mm) 32 Providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete 33 Wiring of light point/ fan point/ exhaust fan point/ call bell pointas per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694)and1.5 sq.mmnominalsize FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)in recessed ISI markedMMS ( IS:9537 P - III ) vergin material PVC conduit & its all accessories( J.B. , Bends etc.) , round tiles,18 SWG G.I. box with earth terminal, 6 A switch , 3 pin ceiling rose/ Lamp holder /3 pointConnector, 3.0mmthickISI marked phenoliclaminatedsheet(IS:2036- 1995), Al.alloy/cadmium platedironscrews20mmcupwashersetc.allasperpre approved by Engineer in charge, making connections, testing etc. completeasrequired. Forspecificationofcopper Conductor, PhenolicLaminatedsheets&Electrical/Wiringaccessoriesrefer Chapter E - 04, E - 05 & E - 07 .For additional technical parameters of products/ work, referAnnexure A attached with this BSR . 34 Short point (up to 3 mtr.) 35 Medium point (up to 6 mtr) 36 Long point (up to 10 mtr) 37 Wiring of 3/5 pin 6 amp. Light plug point as per PWD specificationforelectricalWorkswithISI marked1.5 sq.mmnominalsizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and1.5 sq.mmnominalsize FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI markedMMS ( IS:9537 P - III ) vergin material PVC conduit & its all accessories( J.B. , Bends etc.) , round tiles,18 SWGG.I. box with earth terminal of required size,6 Aswitch, 3/5 pin 6 A socket, 3.0 mmthick ISImarked phenoliclaminated sheet(IS : 2036 - 1995),Al. alloy/ cadmiumplated iron screws 20 mm cup washersetc.allasperpreapproved byEngineerin charge, making connections, testing etc. complete as required. For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessoriesrefer Chapter E - 04, E - 05 & E - 07. Foradditionaltechnicalparametersofproducts/work ,refer Annexure A attached with this BSR . On board 38 S&Ffollowingsizes(dia.)ofISImarkedMMS(IS:9537P-III)vergin material PVC conduit as per PWD specification for electrical Works along with its accessories (IS: 3419 ) as requiredinrecess includingcutting the wall, covering conduit and making good the same as required. All relative and latest acceptancetests reports byanyNABLaccreditedlabfortheconduitshallbesubmitted before execution & All as per pre approved by Engineer in charge. Foradditionaltechnicalparametersofproducts/work ,refer Annexure A attached with this BSR . 25 mm dia 39 SupplyinganddrawingFRPVCinsulated&unsheathed flexiblecopperconductorasperPWDspecificationfor electricalWorkswithISImarked(IS:694)andasperIS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.99%puritycopper,class5strandinginacc.toIEC 60228for lowerwattloss,oxygenfree(<10ppm)for lesschancesofoxidizationandhighersilvercontentfor givesbetterconductivity,insulationPVCtypeA,flame retardantasperIS10810-53,betteramperageratingas perVDE0298part4, ,inexisting surfaceorrecessed PVC/MSconduit/casingcappingincluding allasperpre approved by Engineer in charge,making connections, etc. asrequired.OEMMusthaveitsowninhouseNABLlab setupforalltestingfacilitiesforwires.Foradditional technical parameters of products/ work, referAnnexure A attached with this BSR . 40 2 x 2.5 sq. mm. + 1x1.5sqmm 41 2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 42 Providing&Fixingof240/415VACMCBwithpositiveisolationofbreakingcapacitynotlessthan10KA(B/C tripping characteristic as per type of load andsite requirement) 4KV impulse withstand voltage,as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2,lowwattlosses,tripfreemechanisum,energylimiting of class 3 as per IEC,minimum phase termination capacity of 35sq.mm.,conductorlineloadreversibility,labelholding facility,IP20contactprotectionandfittedwith existing distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A ratingincluding makingconnections,testingetc.asrequired. .OEMshall havesubmit NABL/CPRI/ERDAaccrediatedlabtest reports beforeexecution&Allasperpreapprovedby Engineer in charge.For additional technical parameters of products/work ,referAnnexureAattachedwiththisBSR .Single pole MCB6 A to 32 A rating 43 Double pole 6 A to 32 A rating 44 Providing & Fixing of IK09 recessed/surface mountingheavydutyhorizontaltypesheetsteelof1.6mmthick DistributionboardasperPWDspecification forelectrical WorksISImarkedconformingtoIS-13032&IS-8623/ conforming to IEC 61439-3. Phosphatised/ powder painted completewithsuitableratinginsulatedcopperbusbar, shortinglink,neutrallink,earthlink,connectingwireof suitable rating and din bar,masking sheet, including making internal DBterminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.OEM shall have submitNABL / CPRI/ ERDA accrediated lab test reportsbefore execution & All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer AnnexureA attached with this BSR . 8 Way (8 O/G +2 I/C ) 45 Providing & Fixing of IP20 SMD Mid Power LED batten typeintegrated light fixture made from polycarbonate /extruded aluminiumpowdercoated housingwithinbuiltdriver ,Power Consumption of18W/20W ,system lumen efficacy ≥ 120 lm/Watt output,internalsurgeprotectionof2.5KVwithShort&Open circuitprotection,THD<10%,p.f.≥0.95,CRI>80,lifetimeof minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K/6000°K/6500°K (As per ANSI Bin) , maximum power consumption shouldnotmorethanthespecifiedratingandFixtureshallbeof BIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.OEMmusthaveitsowninhouseNABLlabsetupforalltesting facilitiesforLEDfixtures.(LM79/LM80)certificate/Reportfrom OEMshallbesubmitted.Allasperpreapprovedbyengineerin charge.foeadditionaltechnicalparametersofproduct/work, refer Annexure A attacheded with this BSR. 4 LED Tube shape fixture 18/20 W (Extruded AlBase) 46 Providing&FixingofFluorscenttuberodinexistingfixturesasrequired complete in all respect. Allas per pre approvedby Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 18/20 Watts 47 Providing& Fixingof ISO Certified company made BEEStarratedcopperwoundeddoubleballbearing capacitor start, aluminium body & Metallicblade ceilingfanas per PWD specification for electrical Works, conforming to IS:374-2019, & IS:1885 -P-V- 1981.withdownrodupto30cmwithsecondary support safety cable ( steel wire ) , cotter pin with 3 x1.5 sq.mm pvc insulated flexible copper conductor makingconnectiontestingetc.asrequired. Appropriate OEM test certificate shall be submitted by contractor.AllasperpreapprovedbyEngineerin charge. Foradditionaltechnicalparametersof products/work ,referAnnexureAattachedwith this BSR .1200mmSweepBEE3Starrated (servicevalue >=5.0to< 5.5 ) 48 Providing & Fixing ofISI marked (IS:371) 6 amp surface type 3pin ceiling roses as per PWD specification for electrical Works, made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screws including makingconnectiontestingetc.asrequired.Allasperpre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attachedwith this BSR . 49 Providing & Fixing of ISI marked (IS:1258)6 ampbatten/anglelamp holderasperPWDspecificationforelectricalWorks, made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screws including makingconnectiontestingetc.asrequired.Allasperpre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 50 P & F 18 swgM.S. Recessed fan box, hexagonal/ roundofsize130mmdia,depth75mm,12mmdiarodfan hook with 100 mmlength extended on each side . All as per pre approved by Engineer in charge.For additional technicalparametersofproducts/work ,refer Annexure A attached with this BSR . 51 Providing & Fixing of 240/415 V isolator as per PWDspecification for electrical Works with ISI marked IS:13947- III/conforming to IEC 60947-3, suitable for AC22A utilization catagory, 4KV impulse withstand voltage,true contact indication,Red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting,minimum phase termination capacity of 35sq.mm. , label holding facility , IP 20 contact protection and fitted with existing distribution board / sheetincluding makingconnections,testingetc.asrequired.OEMshall havesubmit NABL/CPRI/ERDAaccrediatedlabtest reports beforeexecution&Allasperpreapprovedby Engineer in charge.For additional technical parameters of products/work ,referAnnexureAattachedwiththis BSR . 30 A / 40 A rating 52 Providing & Fixing of non modular socket size flush type 180watt rotary minimum 5 step fan regulator as per PWD specification for electrical Works, ISI marked (IS:11037) made outfromindustrialgradePolycarbonateorfireresistantABS material including making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure Aattached with this BSR . 53 Supplying and fixing of power plug point with Modularaccessories as per PWD specification for electrical Works, on hotdippedgalvanizedmodularboxof18SWGwith earthing terminal/connector on surface or in recessed with suitable size of modular face place with grid plate and cover plate including cost ofISI marked modular 16 amp. Switch (IS :3854) and 3/5 pin 16 amp. socket outlet (IS:1293) [ as per detailed in respective item in BSR] , making connection , testing , etc. as required.All as per pre approved by Engineer in charge.For additionaltechnicalparametersofproducts/work ,refer Annexure A attached with this BSR .
