|
| 1 | Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity) |
| 2 | Single B.F.S. of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 3 | Ordinary Cement concrete (Mix 1:2:4) with graded stone chips (20mm size) excluding shuttering & reinforcement, if any , in ground flooras per relevant IS Code A) Pakur / chndil varity |
| 4 | Neat cement punning about 1.5 mm thick in wall, dado, window, sills, floor, drain etc. |
| 5 | Brick work with1stclass bricks incement mortar (6:1) In superstructure ,ground floor |
| 6 | 125 mm thick brick work with 1st class bricks in cement morter 1:4 in ground floor |
| 7 | Galvanised corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook-bolts, limpet and bitumen washers and putty complete with 150 mm. end lap and one corrugation minimum side lap. (Payment to be made on area of finished work)(GCI sheet to be supplied by contractor) |
| 8 | Galvanised iron sheet eaves gutter fitted and fixed with necessary 50 mm X 6 mm M.S flat bar clamps bent to design, bolts, nuts, washers etc. complete. Eaves gutter made of 0.63 mm. sheets.(300mm End lapping),225 mm. wide gutter |
| 9 | M.S. structural works with hollow sections (square or rectangular shape) conforming to IS: 806-1968 & IS:1161-1998) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete.i) For roof truss worksa) Span up to 12 Mtr |
| 10 | Labour for hoisting and placing in proper position (up to 1st floor level) departmental R.S. joists, channels, angles. Tees, plates etc. including fitting and fixing same with bolts and nuts, if necessary (but excluding cost of such bolts and nuts) |
| 11 | M.S. gate of Jail type as per approved design made of strong M.S.frame work, intermediate stiffeners and round / square bars or angles. M.S. sheet (not less than 14 gauge) gussets, cleats etc. including necessary riveting, bolting, welding, locking and hanging arrangements, fitting and fixing complete as per direction of the Engineer-in -charge. |
| 12 | Applying exterior grade acrylic primer of approvedquality& brand on plastered or concrete surface old or new surface to receive decorative texture (mat finish orsmooth finish acrylic exterior emultion paint) including scrapping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of E.I.C. In ground floor (Two coats.) |
| 13 | Protective and decorative acrylic exterior emultion paintof approved quality as per manufacturer\"s specification and as per direction of E.I.C. to be applied overacrylic priner as requred. The rates includes the cost of materials, labour, scaffolding and all. |
| 14 | Plaster (to wall, floor, ceiling etc) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints or roughening of concrete surface including throating, nosing and drip course where necessary. …. In ground floor 15mm thick plaster (6:1) |
| 15 | Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 16 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessaryOn Steel or Other metal surface, With super gloss (hi-gloss) Two coats(with any shade except white) |
| 17 | Add GST @ 18% |
| 18 | Add Cess @ 1% |
