|
| 1 | Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to giv a fair finish including centring. shuttering. strutting and propping etc with wooden battens and ballies. height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs.and removal of the same for insitu-reinforced concrete and plain concrete work in :-(1.1)Columns,pillars,posts and struts: |
| 2 | Beams,cantilevers, girders and lintels. |
| 3 | Flat surfaces such as sofits of suspended floors,roofs landings and the like. |
| 4 | Edges of slabs and breaks in floors and walls: Under 20 cm. wide. |
| 5 | Providing and laying cement concrete 1:1.5:3 (1cement :1.5 sand :3 graded stone aggregate 20mm. nominal size) and curing complete excluding cost of form work and reinforcement for feinforced concrete work in :- (2.1) Columns,pillars,posts and struts: |
| 6 | Beams,cantilevers, girders and lintels. |
| 7 | Suspended floors roofs, landings and shelves and their supports, balconies, beams girders bressumers and cantilevers upto allfloors level. |
| 8 | Steel reinforcement for R.C.C. work ready to use \"cut and bend\" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete above plinth level. |
| 9 | Brick work Second class brickusing common brunt clay building bricksin super structure above plinth level upto all floor height in cement mortar 1:6 (1 Cement : 6 Sand) |
| 10 | 15 mmcement plaster in single coat on fairside of brick/concrete/stone walls for interiorplasteringuptoallheightsincludingarises, Internalrounded angles, chamfers and / or rounded angles not exceeding 80 mm in girth and finished even andsmoothincementmortar 1:6 ( 1 cement : 6sand)includingcarriageof material in all leads and lifts.15 mm cement plaster on rough side of single or half brick wall of mix |
| 11 | Providing and fixing anodised aluminium work for door, window, ventilators and partitions with extruded built up standardtubular and other sections of approved makeconforming to IS 733 and IS 1285 anodisedtransparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed withrawlplugs and screws or with fixing clips, or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleat angle,aluminium, snap beading forazing/panelling C.P. brass/stainless steel screws. All complete as per architectural drawings and the directions of Engineer-In-Charge. |
| 12 | For shutters of doors windows & ventilators including providing and fixing hinges/pivots and making provisions for fixing of fittingswhere ever required including the cost of PVC/neoprene gaskets as required (fittings and glazing/panelling shall be paidfor separately)Detail of cost for a door 2.35x0.75 or 20.21 kg. |
| 13 | Providing and fixing panelled glazed or panelled and glazed shutters for doors windows andclerestory windows.including black enamelled iron butt hinges with necessary screws. |
| 14 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coatingnot less than grade AC 10 as per IS : 1868), transparent or dyed to required colour orshade, with nuts and screws etc. complete 250x16 mm. |
| 15 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete. (10.1) 100x10 mm. |
| 16 | 200x10 mm. |
| 17 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete. (11.1) 125 mm. |
| 18 | 75 mm. |
| 19 | Providing and fixing bright finished brass helical door spring (superior quality). Brass helical spring 150 mm. |
| 20 | Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy dutyvetrified tiles Nitco or equivalant 600x600mmx10mm manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade oftiles as required complete. |
| 21 | Providing and applying white wall careputty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 22 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade.New work (two or more coats) over and including water thinnable priming coat with cement primer |
