|
| 1 | Demolition of concrete in ground floor and pavings n.exc 15 cm thickness below or above ground level complete all as specified and as directed. |
| 2 | Demolition of reinforced concrete roofs, floors (other than ground floors), beams, staircases, landing, chajjas slabs; covers and similar suspended work complete all as specified and as directed. |
| 3 | Demolition of cement concrete (unreinforced) in roof (tiling), staircase landing, floors (other than ground floor) includingremoval of debrish outof MoD Land including material and labour for necessary scaffolding, safety arrangement and formwork upto G+3 storeys complete all as specified and as directed. |
| 4 | Taking down existing tarfelt including plaster including material and labour for necessary scaffolding, safety arrangement and formwork upto G+3 storeys complete all as specified and as directed. |
| 5 | Demolition of cement concrete (unreinforced) in roof (tiling), staircase landing ,floors (other than ground floor) includingremoval of debrish outof MoD Land including material and labour for necessary scaffolding, safety arrangement and formwork upto G+3 storeys complete all as specified and as directed. |
| 6 | Rooting out trees, flora & faunaand foliage as grown on RCC roof surfaces and brick/stone walls by cutting hole into slabs/walls for digging out roots and using chemical to burn deep rooted tree roots etc and making good dirturb portion of wall/roof with cement concrete (1:2:4) type B-1 complete all as specified and as directed. |
| 7 | M&L for providing cement concrete (1:2:4), type B-0, (using 12.5 mm graded stone aggregate) as in roof padding to maintain slope etc including material and labour for necessary scaffolding, safety arrangement and formwork upto G+3 storeys complete all as specified and as directed. |
| 8 | M&L for preparationsurface includingcleaning of all dirt andproviding the following water proofing treatment in narrow widthover the roof gutter of stores housesor chajjah/canopy/parapet wall, below PVC/RCC water tanks etc of G+3 storied buildingaccessible / non accessibleRCCroof to be executed through approved applicator of the membrane manufacturer with following specification etc complete all as specified and as directed by Engineer-in-Charge:-(a) Cleaning of all foreign material such as fungus,mass, dust etc by brushing and dusting, sprinkle water on surface, surface shall be levelled with a layer of 20 mm thick CM (1:4) mixed with water proofing admixtureWPC @3% by weight ofas per manufacturer\"s insturctions.(b) Surface shall be throughly wire brushed, cleaned, washed, dried up properly and apply evenly a bituminuous primer coat conforming to IS @0.4 ltr /Sqm over concrete / plastered roof surface.(c) Applying evenly a tack coat of bitumen 85/25 grade @1.20 kg/ sqm.(d) Laying of 3mm thick APP membrane sheet (min weight 3 Kg/Sqm) consistingof a core of 160 gms/Sqm polyster non woven fabric mat protected on both sides with a high quality polymeric asphaltic mix again protected with thermo fusible HMHDPE FILM on dried primed surface by torch application method. APP membrane will normally be laid in length at right angle to the direction of slope. The over lap shall be minimum 100mm on longitudinal direction and 150mm on the transverse direction including cuttings, grooves etc.(e) Membrane bonded completely to the substrate & the over laps are then sealed/fused by flame and including two coats of water proofing bituminous aluminum paint on top of APP membrane complete all as specified and as directed. |
| 9 | M&L for cement concrete tiles 20cm x 20cm x 20mm thick machine pressed, set & pointed in neat cement slurry in floor with grey cement and no pigment and cut and polished on roofover and including 15 mm thick screed bed in CM (1:4) including material and labour for necessary scaffolding, safety arrangement and formwork upto G+3 storeys complete all as specified and as directed. |
| 10 | M&L for special treatment for sunken portion of WCs/Bath & toilet etc executed in following stages:-Stage 1:Cleaning of all foreign material such as fungus,mass, dust etc by brushing and dusting, sprinkle water on surface, surface shall be levelled with a layer of 20 mm thick CM (1:4) mixed with water proofing admixture WPC @3% by weight ofas per manufacturer\"s insturctions.State 2 : Primer-Mix Tarfelt LM of STP Ltd (diluted with water in ratio 1:1) @ 250 gms/sqm and apply the primer on the plastered surfaces.Stage 3 : Application of 1st coat of Tarfelt LM of STP Ltd (without dilution with water) @ 1Kg/Sqm by brush all as per manufacturer\"s instructions.Stage 4:Laying fibre glass cloth (weight not less than 50gram/ Sqm) over the 1st coat while the coated surface is still sticky.Stage 5:After 6 to 7 hours interval, apply second coat i.e. final coat of Tarfet LM of STP Ltd (without Dilution with water) @ 1kg/ Sqm by brush as per manufacturer\"s instructions.Stage 6:Providing 15mm thick protective plaster in CM (1:3) mixed with STP No. 1 @ 250ml/50 Kg cement all as per manufacturer\"s instructions.Stage 7: Carryout ponding test for 48 hours to ensure water tightness of repaired sunken portion. NOTES :- (i)Mode of measurement shall be actual area treated (floor and adjoining walls). |
| 11 | M&L for PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in roof kerbs, benching etc including weathering, slightly rounded or chamfered angle and throughting complete all as specified and as directed. |
| 12 | M&L for providing RCCnominal mix (1:2:4) type B1 (using 20mm graded stone aggregate) as inslabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specifiedand as directed. |
| 13 | Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specifiedand as directed. |
| 14 | M& L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specifiedand as directed. |
| 15 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premices complete all as specified and directed. |
| 16 | Roughening surfaces of old concrete /terrazzo floor by picking, sweeping clean andwashing down with water to removedust, etc. complete all as specifiedand as directed. |
| 17 | M&L for joint free anti skid coloured ceramic tiles, 7 to 8mm thick (squre or rectangular)area of each tile exceeding 0.11sqm but n.exc. 0.18sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces, laid over & including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed. |
| 18 | Description all as per item 17.00 above but as in skirtings laid over and including 10mm thick plaster in CM (1:4) complete all as specifiedand as directed. |
| 19 | M&L for granite (18-20mm thick) work as in counter for cooking &W.H.B platform including rounding and grinding of edges and like laid on cement mortar (1:4) including pointing in white cement (1:2) using marble dust and admixture of pigment to match with shade of granite including cutting for hole, rounding of edges and mirror polishing complete all as specifiedand as directed.. Note:-(a) Rates also includes in this item for necessary raking,circular cutting or notching and waste on Granite(b) This item shall be used for W.H.B Counter top /cooking platfom/ Counter top /skirtings/ vertical surface/steps, jambs, pillars, window-cills etc |
| 20 | M&L for joint free non skid coloured ceramic tiles, 7 to 8mm thick (squre or rectangular)area of each tile n.exc. 0.11sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces, laid over & including 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed. |
| 21 | M&L for joint free coloured glazed ceramic tiles in vertical surfaces of size (300x200)mm x7mm thick/ (450x300)mm x7mm thick, set and jointed in cement slurry and pointed in white or coloured cement to match laid over & including 15mm thick cement rendering in cement mortar (1:4) complete all as specified and as directed. |
| 22 | M&L for 40 mmthick cement concretetype B0, 1:2:4 (using 12.5 mm graded aggregate) as in flooring, to be finished even and fair complete including necessary use and waste of form work complete all as specified and as directed. |
| 23 | M&L for 75 mm thick cement concrete (1:3:6) type C2, (using 40 mm gradedstone aggregate) as in hard standing/pavings/plinth protections, finished even and smooth without using extra cement,complete all as specified and as directed by Engineer-in-Charge. |
| 24 | M & L for machine pressed, glossy finished 25 mm thick coloured cement concrete chequered tiles of size 300mm x 300 mm of pattern as approved, set,jointed and pointed in neat cement slurry mixed with pigment in floorslaid over and including 15mm thick screed bed with cement mortar (1:6) complete all as specified and as directed by Engineer-in-charge. |
| 25 | M&L for machine pressed precast concrete interlocking paver block any shape and size, with grey cement and pigment to match, confirming to IS 15658-2006 of 60mm thick M-35 grade with and including laid over 50 mm thick sand cushioning complete all as specifiedand as directed. |
| 26 | M&L for Durastone vitrifiedtiles coloured, light shade 10 mm thick, area of each tile exc 0.06 butnot exc 0.36 Sqm in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces, laid over & including 15mm thick screed bed in cement mortar (1:6) complete all as specified and as directed. |
| 27 | Demolition of brick work built in cement mortar, including all quoins, arches, pillars etc of any description including removing debrish from site complete all as specifiedand as directed. |
| 28 | M&L for brick work with sub class `B\" bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specifiedand as directed. |
| 29 | M&L for brick work with sub class ‘B’ bricks, straight or curved on plan of any radius in half brick thick wall builtin cement mortar (1:4) complete all as specified and as directed. |
| 30 | Description all as per ser item No 29.00 abovebut except bricks complete all as specifiedand as directed. |
| 31 | Taking down cement plaster/cast in situ terrazo of any description on brick walls or concrete surfaces etc. including raking out joints, hacking for keys, scrubbing down with water complete all as specified and directed by theEngineer-In-Charge.Note:- Quoted rate shall be deemed to be included for welded mesh, scaffolding and necessary formwork for execution upto triple storey bldg. |
| 32 | M&Lfor 10 mm thick plaster on fair faces of brick work or concrete surfaces in cement mortar (1:3) as in ceilings, to befinishedeven and smooth without using extra cement complete all as specifiedand as directed. |
| 33 | M&L for 15 mm thick cementplaster on fair faces of brick work or concrete surfaces in cement mortar (1:6), to befinishedeven and smooth without usingextra cement complete all as specified and as directed. |
| 34 | M&L for 15 mm thick cementplaster on fair faces of brick work or concrete surfaces in cement mortar (1:4), to befinishedeven and fair mix with water proofing compound by weight as per manufacturer\"s instructions including necessaryscaffoldingup to (G+3) storey complete all as specifiedand as directed. |
| 35 | M & L for removing loose, disturbed or disintegrated old concrete surfaces of RCC beam, column, lintel, slab, chhaja pardi, railing etc, cleaning thoroughly exposed reinforcement, applying one coat of anti corrosive paint to the exposed reinforcement, supply and fix of chicken wire mesh of size(50 x 50)mm of 1 mm dia wire, weight not less than 0.55 Kg/Sqm & binding with 22 guage mild steel (annealed)binding wire to reinforcement and applyingrendering 10 mm thick plaster in cement mortar (1:3), after second layer 15 mm thick cementplaster on fair faces of brick work or concrete surfaces in cement mortar (1:4), to befinishedeven and fairwith water proofing compound by weight as per manufacturer\"s instructions and removing the debris outside MD land including material and labour for necessary scaffoldingand formwork upto (G+3) storeys and safety arrangement complete all as specified and as directed.(Note :-The finish of the surfaces to be matched with the existing surface.) |
| 36 | M&L for preparing plastered or unplastered new surfaces on ceilings including brooming down or steel wire brushing, scraping down and applying two coats of white wash complete all as specifiedand as directed. |
| 37 | M&L for preparing oldsurfaces on ceilings including brooming down by mechanicaly, scraping down and applying two coats of white wash complete all as specifiedand as directed. |
| 38 | M&L for preparation of new plasteredsurfaces and applying 3mm thick cement based wall care putty and applying a coat ofalkali resistant primer and two coats of oil bound distemper, up to double storey buildingcomplete all as specified and as directed by Engineer-in-Charge. |
| 39 | M& L for preparation of new plastersurface of walls, chajjas, soffits & beamincluding necessary scaffolding and applying 3 mm average thick cement base wall care putty and two coats of acrylic smooth exterior paint of required shade1.43ltr/10sqmover a coat of exterior primer 2.20kg/sqmall as per manufacturer\"s instructions complete all as specifiedand as directed. |
| 40 | M&L for prepration of old decorated plastered surfaces of walls /ceilings, removal of nails etc & filling cracks/hole by applying cement base wall careputty as required (multipurpose mixer shall be used for uniform and proper mixing of putty) and applying one coat oil bound distemper white or coloured complete all as specified & directed by Engineer-in-Charge. |
| 41 | M&L for complete removal of existing treatment from old decorated plastered surfaces of walls/ceilingsbyremoval of nails etc & filling cracks/hole with putty as required(multipurpose mixer shall be used for uniform and proper mixing of putty) and applying two coats of oil bound distemper white or colouredby rollercomplete all as specified & directed by Engineer-in-Charge. |
| 42 | M&L for applyying 1mm thick cement base wall care putty on wall complete all as specified & directed by Engineer-in-Charge. |
| 43 | M&L for preparationold decorated surfaces of walls and cornices, spoiled bysmoke soot, moulds, moss and efflorescent salts and tradingoily and greasy spots by scraping and washing with water and applying one coat of cement base paint complete all asspecifiedand as directed by Engineer-in-Charge. Note:- The work shall be carried out upto four storey building. Necessay scafolding upto fourstorey bldg shall be deemed to be included in unit rates. |
| 44 | M&L for preparationold decorated surfaces of walls and cornices, spoiled bysmoke soot, moulds, moss and efflorescent salts and tradingoily and greasy spots by scraping and washing with water and applying two coats of cement base paint complete all asspecifiedand as directed by Engineer-in-Charge. Note:- The work shall be carried out upto four storey building. Necessay scafolding upto fourstorey bldg shall be deemed to be included in unit rates. |
| 45 | M&L for preparation of plastered or un plastered old decorated surfaces of wallsremoval of nails etc & filling cracks/hole by applying cement base wall careputty as required (multipurpose mixer shall be used for uniform and proper mixing of putty) and applying one coat of exterior emulsion paint 100% acrilic of approved white or colouredcomplete all as specified & directed by Engineer-in-Charge. Note:- The work shall be carried out upto four store. Necessay scafolding upto fourstory bldg shall be deemed to be included in unit rates. |
| 46 | M&L for preparation of new or previously untreated surfaces of wood of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 47 | M&L for preparation of new or previously untreated surfaces of steel of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 48 | M&L for preparation of old painted surfaces of wood and wood based material of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 49 | M&Lforpreparationofoldpaintedsurfacesofsteelandiron surfacesofany descriptionnototherwise described over10cm width&girth and applying onecoatof synthetic enamelpaint complete all asspecified and as directed. |
| 50 | Taking down shutters of any description area exc 1 Sqm and not exc 2 Sqm each complete all as specified and as directed. |
| 51 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) area n exc. 1.5 sqm each complete all as specified and directed.Note: The damaged portion of the tiles / rendering shall be made good with the same material to match with the adjacent surface. |
| 52 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exc. 1.5 sqm but n exc 4 sqm each complete all as specified and as directed.Note:- The damaged portion of the tiles / rendering shall be made good with the same material to match with the adjacent surface. |
| 53 | S&F rolled mild steel grade Fe-290 Gde-E-165 quality-A as in framed work as in doors or gates of angle or other section gates of with gusset plates, rails, cladding, chowkhats/frame or like etcwelding hold fast, hinges complete all as specified and as directed. |
| 54 | S&F pressed steel frames made out mild steel sheet 1.25 mm thick, with size of frame 105 mm x 60 mmfor doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc and applyinga shop coat of red oxide primer including providing PCC (1:3 :6) type C-0 (using 12.5 mm graded crush stone aggregate) for filling hollow portion of chowkhats complete all as specified and as directed. |
| 55 | S&F pressed steel frames made out mild steel sheet 1.25 mm thick, with size of frame 125 mm x 60 mmfor doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc and applyinga shop coat of red oxide primer including providing PCC (1:3 :6) type C-0 (using 12.5 mm graded crush stone aggregate) for filling hollow portion of chowkhats, complete all as specified and as directed. |
| 56 | M&L in repair for MS works as in holdfast, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging holdfasts, grills, cladding and similar small articles conforming to Fe 290 Gde E-165, complete all as specified and as directed. |
| 57 | M&L for PCC (1:3:6) type C1 (using 20mm graded stone aggregates) as for holdfasts, etc including necessary formwork, complete all as specified and as directed. |
| 58 | S&F factory made glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc. divided into squares, with plain, chamfered or rounded,edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass/gauzeetc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); in second class hardwood, complete all as specified and as directed. |
| 59 | S&F 35mm thick factory made plain, framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and as directed. |
| 60 | S&F 35 mm thick flush shutter solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed. |
| 61 | S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube and fixing in opening as specified and directed. |
| 62 | S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with particle board core 2, 4, or 6 raised panel design with both side 2mm thick 3D wood grain moulded PVC sheet polyurethane painted on the front face &back face, supplying & fixing in frame at site as per specification & drawing. |
| 63 | S&F in replacement of steel window box type made of ERW hollow section of size 130mm x 65mm x 1.25mm thick double rebate comprises gauged and glazes sekelton shutter ERW Section 50mm x 20mm x 1mm thick double shutter with leaf and arrangments for cooler operning including iron grill bar with 12mm square complete welded to frame with vertical muilon of size 130mm x 65mm with 1.25mm thick ERW box typer including holes cutting holes for hold fast (04 Nos each window) and making good dismantled protion with PCC (1:2:4) type B-1 including following fittings welded to frame / shutter :- (a) Hold fast of 150mm long of flat iron 25mmx3mm made to shape-04 Nos each window. (b) MS Handle cold rolled of size 100mm long - 01 No per leaf (c) MS Tower bolt 100mm long- 02No per leaf(d) Z-section 20mmx25mm long stopper - 01No per leaf. (e) MS pintle hinges of size 40mmx25mm -2 Nos per leaf including one coat of red oxide shop primer complete all as specified and as directed. Note:- Wire mesh, sheet glass, painting etc shall be measured and paid separately under respective items. |
| 64 | S&F steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed. |
| 65 | S&F steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and as directed. |
| 66 | S&F in repair drapory rod 25mm dia fancy type mild steel plastic coated inculding wooden funnel and wooden brackets, complete all as specified and as directed. |
| 67 | S&F aluminium alloy, anodised, sliding door bolt 300mm length with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed. |
| 68 | S&F 150 mm long aluminium anodised, handle of extruded section fabricated type anodised and fixed, complete all as specified and as directed. |
| 69 | S&F aluminium, anodised, barrel tower bolts 150mm size of extruded section, complete all as specified and directed. |
| 70 | S&F 125mm long aluminium, anodised, handle of extruded section fabricated type complete all as specified and as directed. |
| 71 | S&F aluminium, anodised, barrel tower bolts 125mm size of extruded section, complete all as specified and directed. |
| 72 | S&F butt hinges, stainless steel, 100mm size, complete all as specified and as directed. |
| 73 | Hacking out old broken glass, any thickness, size, quality, or description from wooden/metal frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete upto 4th storey building complete all as specified and as directed. |
| 74 | S&Fsheet glass 3mm thick, ordinary quality and glazing with oil putty / wooden beads in square or rectangular in section n exc 0.5 sq.m in each pane complete all as specified and as directed. |
| 75 | S&F stainless steel wire cloth0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specifiedand as directed. |
| 76 | S&F figured glass or pin headed type 4mm thick area n exc 0.5 Sqm each and glazing with oil putty,complete all as specified and as directed. |
| 77 | S&F floor door stopper of aluminium alloy body 140mm cover plate and tounge, anodised with hard-drawn steel spring fixed in floor complete all as specified and as directed. |
| 78 | Taking down AC, PVC pipes of 100/110mm diaof any description including all fittings complete all as specified and as directed. |
| 79 | Taking down CI pipes of 100/110mm diaof any description including all fittings complete all as specified and as directed. |
| 80 | Description all as per ser item no. 79.00 above but 75/80 mm dia pipes complete all as specified and as directed. |
| 81 | Supply and fixing 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/floor etc including suitable clamps at one meter of interval complete all as specified and as directed. |
| 82 | S&F for PVC (SWR) bends of radius suitable for 110mm dia PVC pipes fixed complete all as specified and as directed. |
| 83 | S&F 75mm bore cast iron waste and vent pipe in any length with or without ears fixed to floor/ wallsincluding suitable clamps after every one mtr of interval with cement joints fixed to wall complete all as specified and as directed. |
| 84 | S&F 100mm bore cast iron waste and vent pipe in any length with or without ears fixed to walls/floor etc with cement joints fixed to wall including suitable clamps after every one mtr of interval complete all as specified and as directed. |
| 85 | S&F CI 100mm bends with door complete all as specified and as directed. |
| 86 | S&F cast ironfloor trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4)type B1 of size 100 mm including jointing with solvent cement complete all as specified and as directed. |
| 87 | Taking up or down15 to 25 mm steel tubing and connections in walls, ceilings, floors, etc including cleaning for refixing or removal to store complete all as specified and as directed. |
| 88 | S&F tubes, medium grade 15mm dia, galvanized with all fittings and fixed concealed type complete to walls and ceiling or laid in floors complete all as specified and as directed. Note:- Cutting chases in wall for conceal pipe with making good to surface shall be deemed to be included in unit rate. |
| 89 | S&F GI tubing, 20mm bore `medium grade`with all fittings and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed. |
| 90 | S&F GI tubing, 25mm bore `medium grade`with all fittings and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed. |
| 91 | Refixing old 15 mm bore GI steel tubing with new fittings and connectionsin new or old position (walls, ceiling, floors, etc), complete all as specified and as directed. |
| 92 | Refixing old 20 mm bore GI steel tubing with new fittings and connectionsin new or old position (walls, ceiling, floors, etc), complete all as specified and as directed. |
| 93 | Cleaning of PVCover head service tankcapacity 500 liters but not exceeding1000 litres, cleaning by brooming, removing all dirt, vegetation grown on roof, around tank if any, washing the tank with approved bleaching powder, rendering it cleanto store potable water after applying two coats lime wash internally including writing the date of cleaning and capacity of tank with white synthetic enamel paint (letters not exceeding 30 centimetre height) on the outlet surface directly visible upto G+3 storey building complete all as specified and as directed. |
| 94 | Dismantling water tanks exc 250 & n exc 500 capacity in litres and removing to store complete all as specified and as directed. |
| 95 | S&F 500 ltr three layered rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position complete all as specified and as directed. |
| 96 | S&F ball brass valves, 20 mm bore, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed. |
| 97 | S&F gunmetal globe or gate valves, 20 mm bore, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed. |
| 98 | S&F gunmetal globe or gate valves, 25 mm bore, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed. |
| 99 | S&F in repairs 10 litres capacity PVC valvelesssymphonic action type flushing cistern (Economy dual flush) low level, white, with inlet, ball valve, float and handle including brackets and Brass C.P. flush pipe long bend complete all as specified and as directed. |
| 100 | S&F in repair WC Orissa pattern white with integral foot rest(580 x 440)mm includingtrap set,PCC bed and making good disturbed floor connecting to flush pipe complete all as specified and as directed. |
| 101 | S&F in repair Vitreous China wash basin pedestal type, white, flat back, size (550x400) mm, waste, chain and plug andporcelainstopper butincluding brackets, waste coupling and waste pipe complete all as specified and as directed. |
| 102 | S&F PVC connections 15mm size with PTMT nuts of length 600 mm, complete all as specified and as directed. |
| 103 | S&F in repair PVC waste pipe flexible for WHB of 32mm size complete all as specified and as directed by Engineer-in-Charge. |
| 104 | S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and as directed. |
| 105 | S&F in repair plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device complete all as specified and as directed. |
| 106 | S&Fin repairs 15 mm dia long body bib taps fancy type cast copper alloy chromium platedhandle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed. |
| 107 | S&F in repairs 15 mm dia pillar taps swan neck fancy type, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed. |
| 108 | S&F in repairs 15mm bore cast copper alloy CP angular valve ( fancy type), screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and as directed. |
| 109 | S & F in repairs15mm boreconcealed type stop cock long shank and long threading cast copper alloy chromium plated of screwed down to iron pipes, high pressure complete all as specified and as directed. |
| 110 | S&F CI 100mm single branch piece with door complete all as specified and as directed. |
| 111 | S&F CI 75mm bends with door complete all as specified and as directed. |
| 112 | S&F cast iron cowls 100 mm size complete all as specified and as directed. |
| 113 | S&F in repairs, salt glazed stone ware gulley traps of size (150x150)mm square mouthed type ‘P’ including CI cover complete all as specified and as directed. |
| 114 | Dismantlingplain or corrugated steel sheeting any gauge, thickness, incuding Nainital or similar patternsheets in roofcoverings complete all as specified and as directed. |
| 115 | S&F mild steel work (FE 290 Grade E-165) roof trusses (framed), trussed, purlins, crane, gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) includingdistance pieces, cleats etc. complete all as specified and as directed. |
| 116 | S &FPre- paintedgalvalume aluminiumzinc coatingGI basedcorrugatedsteel sheet0.50 mmthickof anycolourhavingtensilestrengthof 550Mpa as in roof covering/cladding to fix the wall fixed with self taping screws with rubber washers etc complete all as specified and as directed.Note:-Pattern, design and colour shall be as approved by GE/ Engr-in-Charge. |
| 117 | S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws with rabber washercomplete all as specified and as directed. |
| 118 | Dismantling ceiling board, any size or description, fixed in any position or in any thickness, including cover fillets with nails complete as specified and as directed. |
| 119 | Providing & fixing false ceiling at all heights with semi perforated 12mm thick micro tegular edged GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of size (595x595)mm of approved texture, design and patterns having moisture content less than 2% , humidity resistance of 99%, NRCO .50 to 0.75 as per IS 8225:1987, noncombustible as per BS 476 (Part 4) -1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33 mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size (15x32) mm of length 3000mm, cross-T of size (15x32) mm of length 1200 mm and secondary intermediate cross -T of size (15x32) mm of length 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e. 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size (85x25x2) mm, galvanised iron perimeter wall angle of size (24x24x0.40)mm of length 3000mm to be fixed on periphery wall/partition with the help of plastic rawl plugs at 450mm center to center and 40mm long dry wall wood screws complete all as specified and as directed. |
| 120 | S&F in repair precast cement concrete louvers and jallies 50 mm thick made of (1:2:4) type B-0 (using 12.5mm graded stone aggregate) including all mouldings but excluding frame and set in cement mortar (1:6) complete all as specified and as directed. |
| 121 | S&F rolled mild steel grade Fe-290 Gde-E-165 quality-A as inframed work as in doors or gates of angle or other section gates of with gusset plates, rails, cladding, chowkhats/frame or like etcwelding hold fast, hinges complete all as specified and as directed. |
| 122 | M&L for steel, plain, black sheet1.00mm thick in wall cladding, steel gates and similar work, cut to size, holes round headed screws, clout nails or rivets and fixed to steel framing with plain 40mm lap joint with reveted or welded seams, including bending orturning up, mitred angles etc. complete all as specified and as directed. |
| 123 | M&L for PCC (1:3:6) type C2 (using 40mm graded stone aggregates) as in foundations, filling and mass concrete, posts and pillarsetc, complete all as specified and as directed. |
| 124 | M&L for mild steel works (Fe-290 Grade E-165) as in posts and struts etc in fencing of angle or other sections, including cutting tops to shape as directed, drilling holes, notching for wire etc, comlete all as specified and directed. |
| 125 | M&L for mild steel plain bar 10 mm dia. and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and as directed. |
| 126 | S&F in repair chain link fencing 4 mm dia of galvanized steel wire 150mm x 100 mm mesh made up into mattresses or cages, lapped wire & laid in position including closing after filling etc including binding with wire complete all as specified and as directed. |
