Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for : |
| 2 | Walls (any thickness) including attached pilasters, buttresses, plinth and string course. |
| 3 | Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands , coping, bed plates, anchor blocks, sills, chhajjas lintel, beam etc. |
| 4 | Columns, pillars, posts and struts etc. |
| 5 | Add extra forcentering and shuttering workin superstructure above floor five level for each four flooror part thereof . |
| 6 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor five level. (\"Original producers\" who manufacture billet directly from iron ores and roll the bilets to produce steel conforming to IS:1786) Tremo Mechanically treated bars |
| 7 | Add extra for reinforcementin superstructure above floor five level for each four flooror part thereof . |
| 8 | Providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, levelling course etc up to floor five level excluding the cost of centering and shuttering.M20 grade Nominal Mix1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stoneaggregate 20mm nominal size). |
| 9 | Add Extra for concrete work in superstructure above floor V level for each four floors or part thereof. |
| 10 | Providing and laying in position Ready mix concrete manufactured in fullyautomatic Batching Plant andtransported to site intransit mixer for having continous agitated mixer, manufactured as per approved mix design of specified grade of RCC work including pumping of R.M.C. from transit mixer to site of laying , exculding the cost of centering, shuttering and reinforcement with all lead and lift including cost of admixtures in recommended portion as per IS 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in charge. All works upto floor V floor M20 grade Design Mix by using cementas per codal provision. |
| 11 | Add extra for providing richer mixes respectively at all floor levels. Providing M-25 grade concrete by usingcement as per codal provision instead ofM-20 grade design mix. |
| 12 | Add extra for RCC work in superstructure above floor five level for each four flooror part thereof . |
| 13 | Providing and fixing 150 mm wide sheet covering over expansion joints with iron screws as per design to match the colour / shadeofwall treatment. Aluminum fluted strips 2 mm thick |
| 14 | Providing and fixing expansion joint board for building RCC column beams, walls, slab of Polyethylene foam of density 30 to 35 Kg/m3 of Armour Board.40 mm Thick |
| 15 | Providing and placing in position suitable PVC water Stops confirming to IS : 12200 for construction/expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete. Serrated with central bulb (225 mm wide, 8.11 mm thick). |
| 16 | Supplying and providing of two components poly sulphide sealant containing solid contents, confirming to standard specification and approved compatible primer, for priming vertical faces prior to application of poly sulphide sealant including all labour charges for sealing of expansion joints after drill mixing of two components sealing compound. Cleaning and preparation of expansion joint using wire brush sand papering with emery paper and filing with suitable mechanical means.The work includes raking and cleaning of joints, sticking, debonding tape on bottom of joint, applying primer on edges, using masking tape on edges, providing of sealant and removal of masking tape immediately after providing sealant in joint. |
| 17 | To vertical joint between R.C.C. columns, bricks & stone masonary in size 40 mm width and 12 mm depth, including providing back up material (Thermocoal foam) if required. |
| 18 | To joints in flooring, as per drawing with first layer of poly sulphide sealant in size 20 mm width and 10 mm depth and then providing polyethylene foam back up rod 25 mm dia size and finally providing another layer of poly sulphide sealant in size 20 mm width and 10 mm depth over P.E. back up rod as per application procedure and direction of Engineer-in-charge. |
| 19 | Providing and laying Autoclaved Aerated Concrete (AAC) blocks masonary 150mm/230mm/300mm thick with Grade-I AAC blocks in superstructure above plinth level upto floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-charge. (The payment of RCC band and reinforcement shall be made for seperately). |
| 20 | Add extra forAAC block masonary work in superstructure above floor five level, for each four floors or part thereof. |
| 21 | Providing and laying Autoclaved Aerated Concrete (AAC) blocks masonary 100mm/125mm thick with Grade-I AAC blocks of density 551 to 650 kg/cum conforming to IS : 2185 (Part-3) in superstructure above plinth level upto floor V level in cement mortar 1:4 (1 cement : 4 coarse sand). The rate includes providing and placing in position 2 Nos. 6 mm dia MS bars at every third course of masonary work. |
| 22 | Add extra forAAC block masonary work in superstructure above floor five level, for each four floors or part thereof. |
| 23 | Providing and fixing of double leaf steel shutterfor cupboard, the frame is made of pressed steelISI section 80x25 mmx1.25 mm thickwith 1.00 mm MS sheet to spot welded including holdfasts of 15x3mm, MS oxidized fittings such as butt hinges, sliding doors bolts, handles, tower bolts and twin peg etc completeincluding applying priming coat of approved steel primer of red oxide zinc chromate andspray painting in approved shade with decopaint of approved quality complete as per direction of Engineer In Charge |
| 24 | Providingand fixing Granite stone slab mirror polished and machine edge cut in Walls, Pillars, Steps, Shelves, Sills, Counters. Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 jointing with white cement mortar 1:2 (1 white cement: 2 marble dust) with pigment to match the shade of the marble slab complete including grinding, rubbing and polishing of: |
| 25 | Jhunjhunu / Jalore (Red/Choclate/Black/Pink Colour) above 3601 cm2 |
| 26 | Extra for providing edge moulding to 15-18mm thick marble/ Granite/Kota stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite/Kota Stone Work Full Edge moulding |
| 27 | Extra for providing opening of required size & shape for wash basin / kitchen sink in kitchen platform, vanit counters and similar location in marble / stone work including necessary holes for pillars taps etc. including rubbing and polishing of cut edge etc. complete. |
| 28 | Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). |
| 29 | Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirmingto IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4). |
| 30 | P & F 1st quality Heavy Duty Vitrified glazed MAT tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1: 4 including grounting the joints with white cement and matching pigment etc complete. size600 mm X 600 mm |
| 31 | Providing non slip grooves to granite/ kota stone flooring, counters, vanities etc. using groove cutter V type including machine polishing to groove to give high gloss finish etc. complete as per design approved by engineer in charge |
| 32 | Providing and fixing external grade board solid core single leaf flush door shutters ISI2202-67 marked using Phenol formal, dehydreresin in glue both sides with approvedsteel fittings complete as per Annexure ‘A’ |
| 33 | Commercial Veneer both side (35 mm thick shutter) |
| 34 | Decorative teakVeneer both side (35 mm thick shutter) |
| 35 | Extraforcuttingrebateinflushdoorshutters(Totalareaoftheshuttertobe measured). |
| 36 | Extra for providing vision panel not exceeding 0.1 Sqm in all type of flush doors (cost of glass excluded) (overall area ofdoor shutter to be measured) : |
| 37 | Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete : 20mm |
| 38 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. With brass cover plate |
| 39 | Providing & Fixing of ward robe shutters made out of 19mm thick BWP block board ISI of superior quality make with following details :-Front side finishing with 1mm thick superior quality mica approved make and 0.8mm thickapproved shade mica in the inner side. Covering with teak wood beading 25x12mm all the sides of shutter & 35x12mm on outer frame for making good the wall joint including heavy brass S.S. fittings (Handle 200mm 2 Nos., Tower Bolt 150mm 2 Nos., Brass Lock 1 Nos., Magnetic Catcher 2 Nos., Brass Hinges 75x40x2.5 mm 6 Nos., SS Hanger Rod 20mm dia)complete as per drawing and design approved by Engineer in Charge. |
| 40 | Steel work in built up tubular trusses including cutting, hoisting ( height upto 10 m)fixing in position and applying a priming coat of approved steel primer, welded and bolted including special shaped washers etc. complete.Electric resistance or induction butt welded tubes. |
| 41 | Providing and fixing pressed steel door frames confirming to IS 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applyinga coat of approved steel primer after pre-treatment of the surface including filling with CC 1:2:4(M15 grade) complete as directed by Engineer-in-charge : Profile C |
| 42 | Profile \"E\" |
| 43 | Providing and fixing in position collapsible steel shutters with vertical M.S. Channels 20x10x2mm and brackets with flat iron diagonals 20x5mm, size with top and bottom rail of T-iron 40x40x6mm, with 40 mm dia steel pulleys / ball bearing complete with bolts, nuts locking arrangements inside and outside stoppers, handles etc. as per specification including applying a priming coat of approved steel primer. (To be measured and paid as per outer dimension). |
| 44 | Supply and fixing in cement mortar welded hand railing made out of MS round or square bars, flats etc. for staircase or verandah as per design complete in all respect (wooden or PVC hand railing to be paid extra) with priming coat of red oxide. |
| 45 | Extrafor providing D type pipe head as top of hand railing |
| 46 | Providing and fixing steel glazed window frame made out of 80x40 mm hollow sheet section of 16 gauge thickness, joint mitred weldedand grinded including hold fast of steel lugs 13mm x 3mm and 15 Cm long embedded in C Cblock 15 x 10 x 10 Cm of 1:3:6 nominal concrete and including fixing of pivoted hinges of superior quality, window shutters made out of 50 x 25.0 mm hollow steel section 15 mm paitam of 18 gauge thickness, joint mitred and grinded including 10mm x 10mm square bars welded to framefor paitam fixing float glass 4mm thickpanes with glazing clips and metal sash putty andfixing of shutters frames peg stay, U shape handle 100 mm long, tower bolts 100 mm long of steel powder coated superior quality including fixing and jointing with frame hinges priming coat with steel primer complete in all respect as per direction of Engineer-in –charge |
| 47 | Window openable. |
| 48 | Window fixed. |
| 49 | Extra for additional shutter in pipe section windows with wire gauge 14 mesh x 24 gauge |
| 50 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2coarse sand : 4 stone aggregate 10mm and down gauge) includingfinishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : |
| 51 | Making khurras 450 x 450mm with average minimum thickness 50 mm cement concrete 1:2:4 over P.V.C. Sheet 1 Mtr. x 1 Mtr. x 40 micron finished with 12 mm cement plaster 1:3 and one coat of neat cement, rounding edges and making and finishing the out let complete. |
| 52 | Providing and fixing stainless steel railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) Grade 304 |
| 53 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting offollowing operations. (a) Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm. of cement admixed with proprietary water proofing compound conforming to IS. 2645 over the RCC slab including cleaning the surface before treatment. (b) Laying cement concrete using broken bricks/brick bats 25 mm to 100mm size with 50% of cement mortar 1:4 (1 cement : 4 coarse sand) admixed with proprietary water proofing compound conforming to IS : 2645 over 20 mm thick layer of cement mortar of mix 1:4(1 cement :4 coarse sand )admixed with proprietary water proofing compound conforming to IS : 2645 to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry admixed with proprietary water proofing compound conforming to IS : 2645. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix1:4 (1 cement :4 coarse sand) admixed with proprietary water proofing compound conforming to IS : 2645and finally finishing the surface with trowel with neat cement slurry and making of 300x300xmm square (e)The whole terrace so finished shall be flooded with water fora minimum period of two weeks for curing and for final test.All above operations to be done in order and as directed and specified by the Engineer-in-Charge.With average thickness of 120mm and minimumthickness at khurra as65 mm. |
| 54 | Crazy marble stone flooring 20 mm thick marble stone with black or of specified colour topping including filling the gaps with cement marble chips mix in proportion of 4:7 (4-Cement:7-White black or white or black marble chips) size from 1 mm to 4 mm by volume and under layer of 25 mm thick cement concrete [1:2:4, graded stone aggregate 12.5 mm nominal size] rubbing and polishing and cement slurry etc. complete :In ordinary cement. |
| 55 | For area of each slab up to 2001 to 5000Sq. Cm :25 mm thick |
| 56 | Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete |
| 57 | For area of each slab upto 2001Sqcm |
| 58 | For area of each slab from 2001to 5000 Sqcm |
| 59 | Extra for Mirror polishing on terrazzo/Kota stone work where ever required to give high gloss finish complete. |
| 60 | Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. |
| 61 | Plaster on new surface on wall in cement sand mortar 1:6 including raking of joints etc. complete fine finish : |
| 62 | 20mm thick. |
| 63 | 6mm cement plaster to ceiling of mix 1:3 (1 Cement : 3 fine sand) |
| 64 | Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. |
| 65 | 21 to 25.2 |
| 66 | 25.2 to 29.4 |
| 67 | Making of drip course (Tapka) in cement sand mortar 1:6 width upto 40 mmand 10 mm thick as per approved design |
| 68 | Providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete |
| 69 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work including preparation of base with primer, putty, lippy complete in all respect. |
| 70 | Finishing walls with textured exterior paint of required shade as per approved colour complete as per manufacturers specificationsincluding primer coat and protecting coat including scaffolding and safety provision. Trowel Finishav. thickness 2000 to 2500 microns. |
| 71 | Paintingwith enamelpaint of approvedbrandand manufactureto give an even shade: Two or more coats on new work. |
| 72 | Providing and applyingMelamine polish on teak wood work of approved brand and manufacture to give an even shade with twoor more coats by compressor including sand papering,wood filler coat etc complete in all respect: New Surface |
| 73 | Providing and laying water proofing treatment to vertical and horizontal surface of depressed portions of W.C. kitchen and the like consisting of. I) 1st course of applying cement slurry @ 4.4 Kg./sqm\" mixed with water proofing compound \"Impermo\" of Snowcem or equivalent conforming to IS : 2645 in recommended proportions. II) IInd course of 20mm cement plaster 1:3 (1-Cement:3-coarse sand) mixed with water proofing compound in recommended proportion. III) IIIrd course of applying blown or residual bitumen applied hot a 1.7 Kg. per sqm. of area. IV) Ivth course of 400 micron thick PVC sheet (Overlaps at joints of PVC sheet should be 100mm wide and pasted to each other with bitumen @ Kg/Sam.). |
| 74 | Providing & laying Chequerred terrazzo tiles of approved make 22 mm thick with marble chips of size upto 6mm, in floors, jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and polishing complete in all respect as per specification, on 28 mm thick bed of C.M. 1:4 Dark shade using ordinary cement. |
| 75 | Providing and fixing Structural glazing work with toughened glass of 6mm thick and reflective colour as approved in dark shade like Blue/Dark Blue etc. with frame work of curtain section 65x60mm (Weight 1.64 kg/m min.) made of aluminium with chrome plating. Internal frame work will also be of curtain section 65x60mm of chrome plated aluminium section with20x20mm aluminium tube section and structural spacer made of rubber. The aluminium frame worksize as per instruction of Engineer-in-charge and including openable panels with all necesary sections and fitting.The work include silicon structural adhesive for complete gripping of glass with framing members and silicon weather seal sealant to prevent moisture/water through joints. Glass will be fixed in plumb and with uniform spacing of 10-12mm wide duly filled with silicon weather seal sealant. The work includes all labour,scaffolding , structural aluminium work, toughened glasses,silicon weather seal sealant, silicon structural adhesive structrucal spacer, all accessoreis like handles, peg stays, M-15 grade cement concrete for fixing holdfast .(Face area of glass shall be measured) |
| 76 | Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing upto any pitch including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% Ultra-voilet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall confoim to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. |
| 77 | 5.0 mm thick (Wt.8.4 Kg./Mtr.Sq.) |
| 78 | Extra for corrugatedFiberglassReinforced Plastic (FRP) (2.5\" /4.2\"/6\") or step down(2.5\" /4.2\"/6\") as specified. |
| 79 | Providing and Fixing Chiken wire mesh at the joint of masonry members/ R.C.C. Memberswith Nails complete in all respect. |
| 80 | Applying priming coat: |
| 81 | With ready mix pink or gray primer of approved brand and manufacture on wood work hard and soft wood. |
| 82 | Painting with synthetic enamel paint of approved brand and manufacture togive an even shade : |
| 83 | New wood work(two or more coats). |
| 84 | P & F Indian type white glazed vitreous china Ist quality W.C. orissa pan (IS:2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor : |
| 85 | Size 580x440mm. |
| 86 | P & F European type white glazed vitreous china Ist quality W.C. pan (IS:2556 Mark) with P or S trap including cutting and making good the wall and floor. |
| 87 | P & F water closet Seat Covers with brass hinges complete : |
| 88 | Solid PVC (IS 2548 marked) grade-I White for EWC. |
| 89 | P & F C.P. lugs for toilet seat cover. |
| 90 | P & F Ist quality WVC Urinal (IS:2556 mark) with 25 mm dia G.I. waste pipe, dome couplings, concealed iron brackets or screws etc. complete. |
| 91 | Flat Back (large) or half stall size 610x400x80 mm. |
| 92 | P & F Marble Urinal Partition slab both sides polished of approved design cut from marble size 900x600mm. |
| 93 | Makrana \"Adanga\" or Raj Nagar IStQuality White or Andhi Indi-Italian marble. |
| 94 | P & F Low level Flushing Cistern of 10 litres capacity (IS:2556 mark) of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS:1703 mark) complete including cutting and making good the wall : |
| 95 | PVC with PVC bend as per IS : 7231 |
| 96 | P & F C.P. brass Urinal Flush pipe set complete with flanged brackets of approved make. |
| 97 | For 2 Urinals. |
| 98 | P & F C.P. brass Urinal Spreader for stall urinal of approved make. Synethic (PTMT) |
| 99 | P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make 25 mm G.I. waste pipe complete including cutting & making good the wall : |
| 100 | Size 610 mm x 510 mm |
| 101 | Size 630 mm x 500 mm dia for counter top. |
| 102 | P & F kitchen & Lab Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up to floor level complete including cutting and making good the wall & floor : |
| 103 | WVC Lab Sink (IS:2556 Mark) size 530x430x180 mm. |
| 104 | 1.0 mm thick stainless steel AISI -304 & IS 13983-1994kitchen sink of approved make as per Engineer-in-chargewith large waste coupling. |
| 105 | Size 37x18x7 |
| 106 | P & F Drain Board of approved make with C.I. brackets duly painted complete including cutting & making good the wall : WVC (IS: 2556 Mark) size 530x450mm |
| 107 | P & F Bottle Trap of approved make |
| 108 | C.P. Brass 40 mm |
| 109 | P&F waste coupling with fitting of approved quality/ make : |
| 110 | -do- 40mm dia |
| 111 | P & F Bevelled edge Mirror/mirror with teak wood lipping around of special glass of approved make as per direction of Engineer-in-charge complete with 6mm thick commercial ply base fixed to wooden screws & washers. |
| 112 | Other sizes |
| 113 | P&F towel rail or ring of approved quality /make: |
| 114 | C.P. brass towel rail elbow type with concealed screws size 450mm (heavy duty) |
| 115 | Synthetic material (PTMT) of approved quality/ make size 525 x 90x 75mm. |
| 116 | P&F Grating of approved quality/ make |
| 117 | Stainless steel sheet size 125mm dia |
| 118 | P&F liquid soap contained with brackets complete of approved make : |
| 119 | C.P. brass |
| 120 | P&F toilet paper holder with rod of approved quality/ make. |
| 121 | C.P. brass heavy & superior quality |
| 122 | P&F Soap dish or tray of approved quality/ make. |
| 123 | C.P. brass heavy and superior quality |
| 124 | P&F Shower arm 15mm dia of approved quality/ make. |
| 125 | C.P. brass heavy & superior quality 150mm projection.size 370mm |
| 126 | P&F Bath shower of approved quality/ make . |
| 127 | C.P. brassof Heavy & superior quality, revolving with adjustable key 150mm. |
| 128 | P&F extension pipe for bib cocks of approved quality/ make: |
| 129 | C.P. brass of Heavy & superior quality 50x15mm |
| 130 | C.P. brass of Heavy & Superior quality 100x15mm |
| 131 | P&F Jet spray for water closet with C.P. copper tube flange of approved make |
| 132 | Providing and fiixng C.P. flange for 15mm dia taps |
| 133 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.,) |
| 134 | 20mm nominal outer dia pipes |
| 135 | 32mm nominal outer dia pipes |
| 136 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1 metre spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall) |
| 137 | 20mm nominal outer dia pipes |
| 138 | 32mm nominal outer dia pipes |
| 139 | 40 mm nominal outer dia pipes |
| 140 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement , trenching refilling & testing of joints complete as per direction of Engineer in Charge.(External work). |
| 141 | 25 mm nominal outer dia pipes |
| 142 | 32mm nominal outer dia pipes |
| 143 | 50 mm nominal outer dia pipes |
| 144 | P & F Ball Cock (IS:1703 Mark) with Rod & P.V.C. Ball complete : |
| 145 | Brass wt. not less than 300 gm, 15 mm. |
| 146 | P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. |
| 147 | C.P. Inlet connection 15 mm Brass (IS:8931 marked). |
| 148 | P & F 15 mm. Dia Connection pipe of approved quality/make: |
| 149 | -do- 450 mm. |
| 150 | P & F Full-way valve (IS:778 Mark) or wheel valve of approved make : |
| 151 | Gun-metal 15 mm nominal bore. |
| 152 | (-do-) 25mm nominal bore. |
| 153 | (-do-) 32mm nominal bore. |
| 154 | P & F Gun-metal Non-return Valve or Check Valve (IS:Make) of approved make, superior quality : |
| 155 | 25mm nominal bore. |
| 156 | 32mm nominal bore. |
| 157 | 50 mm nominal bore. |
| 158 | P & F PVC Storage Tank (IS:12701 marked indicating the BIS license No.) of approved make with cover, 25 mm dia 1 M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc. complete of approved design. |
| 159 | 500 litres capacity. |
| 160 | 1000 litres capacity. |
| 161 | 2000 litres capacity. |
| 162 | 5000 litres capacity. |
| 163 | Hoisting Charges for each floor : |
| 164 | For items 2.261 to 2.26.4 |
| 165 | For item 2.265 to 2.26.8 |
| 166 | P & F Pillar Cocks (IS:8931:1993 Mark) of superior quality and approved make : C.P. Pillar cock, Swan-neck with castedspout, 15 mm nominal bore. |
| 167 | P & F Bib Cock (IS:8931 Mark) Superior quality of approved make : C.P. Brass bib cock, 15 mm nominal bore. |
| 168 | P & F Bib Cock (IS:8931 Mark) Superior quality of approved make : Long body, 15 mm nominal bore weight not less than 690 gm. |
| 169 | Providing and fixingSuperior quality CP Brassfittings of approved make as per direction of Engineer-in-charge Angular stop cock with long thread 15 mm nominal size |
| 170 | P & F Stop cock (IS:8931 Mark) superior quality & of approved make : Concealed Stop Cock 15 mm. |
| 171 | Providing and fixing Premiumquality CP Brass fittings Complete as per direction & Approval of Engineer Incharge. Central hole basin mixer |
| 172 | Wall mixer 3 in 1 system with provision of telephonic bath shower with bend pipe |
| 173 | Double Coat hook(MCH/IVC) |
| 174 | P&F toilet paper holder with rod of approved quality/ make. C.P. brass |
| 175 | Providing Laying & jointing glazed S.W. pipes grade `A` (IS;651 marked) of approved make with spun yarn & stiff mixture of cement mortar 1:1 excavation & refilling of earth in all types of soil upto 1.2m depth, S.W. fittings, including testing of joints etc, complete. |
| 176 | 150mm dia |
| 177 | 250mm dia |
| 178 | Providing & Laying C.C. 1:5:10 (Stone aggregate 40 mm nominal size) all around S.W. pipe including 15 Cm. thick bed concrete as per Rajasthan P.W.D. specifications : (Width W=Diameter of pipe in Cm+30 Cm.)(Excluding cost of pipe). |
| 179 | 150mm dia S.W. Pipe. |
| 180 | 250mm dia S.W. Pipe. |
| 181 | Providing & fixing S.W. square mouth Gully trap `A` grade (IS 651-1992marked) of approved make & design in existing man-hole. |
| 182 | Size 100x100mm. |
| 183 | Size 150x100mm. |
| 184 | P & F Square-mouth gully trap `A` grade (IS 651-1992 :marked) of approved make complete with C.I. grating, frame & Cover masonary chamber in C.M. 1:6, 100mm thick C.C. 1:5:10 base concrete, 40mm thick C.C.M-15 grade coping, 12mm thick cement plaster in CM 1:3 complete as per approved design & type. |
| 185 | Trap size 225 X 150 mm, ferrow cement cover with frame Internal Chamber size 450 X 450mm. |
| 186 | P&F rigid PVC Pipe (IS:4985 mark) class II(4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant |
| 187 | 75mm dia |
| 188 | 110mm dia |
| 189 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: |
| 190 | Coupler(socket) |
| 191 | 75mm dia |
| 192 | 110mm dia |
| 193 | Plain Tee |
| 194 | 75mm dia |
| 195 | 110mm dia |
| 196 | Door Tee |
| 197 | 75mm dia |
| 198 | 110mm dia |
| 199 | Door \"Y\" |
| 200 | 75mm dia |
| 201 | 110mm dia |
| 202 | Bend 45 |
| 203 | 75mm dia |
| 204 | 110mm dia |
| 205 | Bend 87 .5 |
| 206 | 75mm dia |
| 207 | 110mm dia |
| 208 | Door Bend (Top Side) |
| 209 | 75mm dia |
| 210 | 110mm dia |
| 211 | Vent Cowel |
| 212 | 75mm dia |
| 213 | 110mm dia |
| 214 | Pipe Clip |
| 215 | 75mm dia |
| 216 | 110mm dia |
| 217 | Plain floor trap |
| 218 | 110mm dia |
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail