|
| 1 | Earth work excavation for foundations in all types of soils other than soft and hard rock up to a depth not exceeding 1.500 mts from original average ground level, back filling in plinth and around foundations with excavated soil in layers not exceeding 150 mm, watering, consolidating including de-watering if required and disposing of surplus earth within a distance of 500 mts etc., all complete as per drawings, specifications and as directed by the Engineer. |
| 2 | Providing and laying plain cement concrete 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate) using 40 / 20 mm nominal size stone aggregate of approved quality forfoundations, steps / ramps,under floors including form work, consolidation, leveling, finishing and curing etc., all complete as per drawings, specifications and as directed by the Engineer. |
| 3 | Providing and laying plain cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) with 20mm and down gauge stone aggregate of approved quality in pedestals / floor including grouting structural steel posts to required alignment and level, consolidation, form work, curing etc., all complete as per drawings, specifications and as directed by the Engineer. |
| 4 | Providing and laying cast - in - situ machine mixed cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate) for reinforced cement concrete worksusing20 mm and down gauge stone aggregate of approved quality including shuttering and centering, consolidating, finishing, curing etc.,all complete at all levels as per drawings, specifications and as directed by the Engineer, but excluding cost of reinforcement steel.4.1). Slabs, chajjas |
| 5 | Providing, hoisting and fixing precast reinforced cement concrete slab over storm water drain in theproportion 1:1.5:3 (1 Cement: 1.5 coarse sand: 3 graded stone aggregate)using20 mm and down gauge stone aggregate of approved quality including setting in position with cement mortar 1:3 (1 cement: 3 coarse sand), including required centering/ shuttering, finishing with neat cement on exposed surfaces and curing but excluding cost of reinforcement all complete as per drawings, specifications and as directed by the Engineer. |
| 6 | Providing, laying and fixing in positionFe 500 grade TMT reinforcement steel of M/s SAIL/TATA/VIZAG brand conforming to IS 1786 for all reinforced cement concrete works including cutting, bending, supplying and binding with 16 gauge MS annealedwire, supplying and laying spacer blocks etc., all complete at all levelsas per drawings, specifications and as directed by the Engineer. |
| 7 | Providing and laying brick masonry in cement mortar 1:6 (1 cement: 6coarsesand) using common burnt clay bricks of class designation 7.5 including racking of joints, scaffolding, curing etc., all complete at all levels as per drawings, specifications and as directed by the Engineer. |
| 8 | Providing and laying 115 mm thick brick masonry in cement mortar 1:4 (1 Cement : 4Coarse sand) using common burnt clay bricks of class designation 7.5including racking of joints, scaffolding, curing etc., all complete at all levels as per drawings, specifications and as directed by the Engineer. |
| 9 | Providing and plastering with CM 1:4 (1 cement: 4 coarse sand) of thickness 12 mm to 20 mm in patches including cutting patches in proper shape, racking out joints, preparing and plastering the surface of walls, scaffolding, curing, disposal of rubbish within a distance of 500 mts etc.,all completeat all levelsas per drawings, specifications and asdirected by Engineer. |
| 10 | Providing and laying 15 mm thick plaster in Cement mortar 1:6 ( 1 Cement : 6 coarse sand) on concrete/brick masonry surfaces including hacking of concrete surfaces, curing, scaffolding, providing grooves etc.,all completeat all levelsas perdrawings, specifications and asdirected by theEngineer. |
| 11 | Providing and fixing stainless steel fly proof wire gauge of 0.5 mm dia wire and aperture 1.4 mm on both sides fixed to ventilators with Aluminum flat of size 15 x 3 mm including necessary screws etc., all complete at all levels as per specifications and as directed bythe Engineer. |
| 12 | Providing and applying two or more coats ofacrylic smooth exterior emulsion of approved brand/ shade over a coat ofexterior wall primer of approved brand / shade on cement based paint / colour wash finished external wall surface in even shade including removing layers of colour wash by scraping and sand paperingmanually / mechanical means, doing necessary repair to scratches, filling cracks using birla wall care putty, water washing the entire surface, preparing the entire surface smooth and fit for primering, scaffolding, cleaning etc..,all complete at all levels as per specifications and as directed by Engineer. |
| 13 | Providing and applying two or more coats of chlorinated rubber paint of approved manufacture and shade over a coat of zinc chromate red oxide primer on existing chain link fence / gratings / purlins including surface preparation etc.., all complete at all levels as per specifications and as directed by Engineer. |
| 14 | Providing and fixingnon-asbestos high impact Polypropylene reinforced cement 6 mm thick corrugated sheets (as per IS: 14871) roofing up to any pitch and fixing with polymer coated J, or L hooks, bolts and nuts 8 mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete (excluding the cost of purlins, rafters and trusses), including cutting sheets to size and shape wherever required, removing existing damaged roofing sheets and stacking in store yard etc., all complete at all levelsas per drawings, specifications and asdirected by theEngineer. |
| 15 | Providing, fabricating, transporting, erecting and fixing steel structure in position made of angles, channels, flats, pipes, plates etc., of M/s.SAIL/VSP/TATA/JINDAL brand for MS door / ventilators, gate posts, fencing posts etc., as directed, nuts, bolts, washers, cutting and welding at site, painting the structure with two or more coats of chlorinated rubber paint of approved manufacture and shade over a coat of zinc chromate red oxide primer etc., all completeat all levelsas perdrawings,specifications and asdirected by theEngineer. |
| 16 | Providing and fixing 50 mm X 50 mm X 4 mm GI chain link fence of approved quality over angle iron / channel posts, tightening and tempering the chain link fence to avoid any undulations using 25 X 6 mm MS flats, providing two rows of 8 gauge GI wire at top and bottom of chain link fence, providing and applying two or more coats of chlorinated rubber paint of approved quality and shade over a coat of approved primer etc., all complete as per drawings, specifications and as directed by the Engineer. Note: (25 X 6 mm MS Flat shall be measured and paid under item No.15) |
| 17 | Providing and laying factory made chamfered edge 60mm thick cement concrete paver blocks of M-35 grade in floor, drive ways or light traffic parking etc., of required strength, thickness and size/shape, made by table vibratory method using PU mould, laid in required colour and pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size pattern, finishing and sweeping extra sand etc., all complete as per direction of Engineer. |
| 18 | Demolishing brick works manually /mechanical means including stacking of serviceable bricks at civil store, scaffolding anddisposal of debris within a distance of 500 mts etc.., all completeat all levelsas per specifications and as directed by the Engineer. |
| 19 | Demolishing plain cement concrete manually /mechanical means including stacking of serviceable bricks at civil store, scaffolding anddisposal of debris within a distance of 500 mts etc.., all completeat all levelsas per specifications and as directed by the Engineer. |