Tender For Repair Of Cane Society Building Rampur District Rampur. - Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead. 2 Dismentling Doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, hold fasts etc. complete and stacking within 50 meters lead. 3 ANTITERMITE TREATMENT:Treatment of soil under existing floors using chemical emul sion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: 2.35.3.1 With Chlorpyriphos E.C.20% with 1% concentration 4 PCC Work:Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland / Portland Slag cement, admixtures in recommended propor-tions as per IS:9103 to accelerate /retard setting of concrete, to improve durability and work ability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the minimum specified cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. 4.20.1 All works upto plinth level :4.20.1.4 Concrete of M25 grade with minimum cement content of 300 kg /cum 5 Plaster on Internal Wall:12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) 6 Plaster on External Side:12 mm cement plaster on rough side of single or half brick wall of mix:1:4 (1 cement: 4 coarse sand) 7 Putty Work:Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 8 Oil Bound distemper:Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer 9 Premium Acrylic Smooth exterior paint:Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: 13.47.1 New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 10 Floor Tiles:Providing and laying vitrified floor tiles in different sizes (thickness to bespecified by the manufacturer) with water absorption less than 0.08%and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),jointing with grey cement slurry@ 3.3 kg/ sqm including grouting the joints with white cement & matching pigments etc. complete. Size of Tile 600x 600 mm 11 Wall Tiles:Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 12 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. 13 Door Frame Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge: 14 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding. 15 Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). 16 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes. 17 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 11.3.1 40 mm thick with 20 mm nominal size stone aggregate ( 40 mm thick with 20 mm nominal size stone aggregate) 18 Provinding and laying APP (atactic Polyproplene polymer) modified prefabricated five 3mm thick water proofing membran, black finisihed rein forced with glass bitumen membran @0.40 ltr/Sqm by the membran manufactur of density at 0.87-0.89 kg /ltr & biscocity 70-160 cps etc for all comp. of the work.DSR- 19 SCHEDULE OF QUANTITIES FOR ELECTRICAL WORKS 20 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. 21 Wiring for circuit/sub-main wiring along with earth wire with the following size of FR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVCconduit as required. 22 2X1.5 sqmm + 1x1.5 sqmm earth wire 23 2X2.5 sqmm + 1x 2.5 sqmm earth wire 24 2X4.0 sqmm + 1x 4.0 sqmm earth wire 25 Supply and fixing of following size of PVC conduit alongwith the accessories in recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required: 26 Supply and fixing of stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. 27 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. 28 Supplying and fixingfollowing size/modules, GI box along with modular base& cover plate for modular switches in recess etc as required. 29 Supply and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 modular switch, connection etc. as required. 30 Supply and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connection etc. as required. 31 Supplying and fixing 3 pin 5 A ceiling rose on the existing junction box/woodedn block including connectionetc. as required. 32 Supplying and fixing brass batten/angle holder including connectionetc. as required. 33 Instalation,testing & commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLSCFL/LED lamps per fitting, complete with all accessories including connection etc. as required. 34 Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc.Including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. 35 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Disect Current(BLDC) motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value(CM/M/W) minimum 6, Air delivery minimum 210 Cum/Min, 350 RPM(tolerance as per IS: 374-2019), THD less than 10% remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise= 75 degree C(max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. 36 DISTRIBUTION BOARDS, MCBS & ISOLATORS 37 Supplying and fixing following way, Horizontal type three pole and neutral MCB distribution board, 415 volts on surface / recessed complete with tinned copper busbar, neutral busbar, earth bar, din bar, interconnections, powder painted including earthing etc. ar required (but without MCB / RCCB / isolators). 38 Supplying and fixing 5 amps. to 32 amps. rating, 240 volts `C series,miniature circuit breaker (MCB) suitable for inductive load offollowingpolesin the existingMCBDBcomplete with connections, testing andcommissioning etc. as required. 39 Supplying and fixing single pole, blanking plate in the existing MCB DB complete etc. as required. 40 Supply and fixing following rateing four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 41 40 A 42 63 A 43 Supplying and fixing cable end box (loose Wire Box) suitable for following triple pole and neutral , sheet steel, MCB distribution board, 415 Volts, on surface/recess, complete with testing and commissioning etc. as required. 44 For 4 way, Double Door TPN MCB DB 45 Supply and installing of following size of perforated pre-painted M.S. CABLE TRAYS with perforation not more than 17.5% in convenient sections, jointed with connections, suspended from the ceilling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 46 300mm width x 50mm depth x 1.6 mm thickness 47 600mm width x 62.5mm depth x 2 mm thickness 48 Earthing with GI earth pipe, 600mm x 600mm x 6mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/cock and salt as required. 49 Earthing with Copper earth pipe, 600mm x 600mm x 3mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/cock and salt as required. 50 Supplying and Laying of 25mm x 3mm G.I. strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) 51 Providing & fixing 25mm x 5mm Copper strip on surface or in recess for connection etc. as required. 52 Supplying and Laying of 6 SWG GI wire at 0.50 metre below ground level for conductor earth electrode, including connection / terminating with G.I. thimble etc. as required. 53 Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. 54 Supplying & making end termination with brass compression gland and aluminium lugs for the following size of PVC shearhed / XLPE aluminium conductor cable of 1.1 KV grade as required. 55 Providing, Laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I fitting including trenching (75 cm deep) and refilling etc. as required. 56 Supply of following size of 1.1 KV grade multicore aluminium conductor PVC sheathed armoured cable as per IS 1554. Make-Polycab or Eq. 57 Supply of 12 W Led BULB complete in all respect. Make-Philips or Eq 58 Supply of LED Tube Light with battern suitable for up to 1x20 watt LED tube light complete including tube etc. on surface / Pendent complete in all respect. Make-Philips or Eq. 59 SCHEDULE OF QUANTITIES FOR SANITARY WORK 60 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required 61 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 62 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required 63 Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete. 64 a) 32mm dia 65 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 66 Providing and fixing PTMT Liquid soap container 109 mm wide ,125 mm high and 112 mm distance from wall of standerd shape with bracket of the same material with snap fittings of approved quality and colour weighing not less than 105 gms. 67 Providing & fixing PTMT towl rail complete with brackets fixed to wooden cleats with cp brass screws with concealed fitting arrangement of approved quality and colour. 600 mm. long towl rail length of 645 mm. width 78 mm. and effective height of 88 mm, weighing not less than 190 gms. 68 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion . (i) Single socketed pipes. 69 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,punning,rounding the edges and making and finishing the outlet complete. 70 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 71 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 72 Providing & fixing G.I. pipes complete with G.I. fittings & clamps including cutting & making good the walls etc. 73 Painting G.I. pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality. 74 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 75 20mm dia nominal outer dia pipes 76 25mm dia nominal outer dia pipes 77 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge. 78 15mm dia nominal outer dia pipes 79 20mm dia nominal outer dia pipes 80 25mm dia nominal outer dia pipes 81 Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions. 82 Providing & fixing CP brass bib cock of approved quality conforming to IS 8931 83 Providing & fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 84 Providing & fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS 8931 85 Providing & fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. 86 Providing and fixing gun metal gate valve with wheel of approved quality. 87 25mm dia nominal bore 88 20 mm dia nominal bore 89 32mm dia nominal bore 90 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 91 Providing and placing on terrace (at all floor levels) polyethylene water storage tank. IS:12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 92 Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m.including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m.Pipes, cables etc. exceeding 80mm dia. But not exceeding 300 mm dia. 93 Providing, laying and joining glazed stone ware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. 94 100mm diameter 95 150mm diameter 96 Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround S.W. Pipes including bed concrete as per standard design. 97 100mm diameterS.W. Pipe 98 150mm diameterS.W. Pipe
