|
| 1 | Part-AProviding and installing an Air Walker at the site as per the specifications mentioned below:1. Dimensions (LxWxH): 1100 x 450 x 1300mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. ‘U’ shaped main frame of NB 80mm (G.I.) ‘C’ Class Pipe, Leg Support frame of NB 50mm(G.I.) ‘C’ Class Pipe.4.Handle frame pipes of NB 32mm (G.I.) ‘C’ Class. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored. 9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 11. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 14. High tensile steel with galvanized nut bolts are used for assembly. 15. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.16. Self-Explanatory stainless steel label fixed on equipment for ease of use.17. Pipe and sheet components should be cut by laser machine having CNC made components welded with robotic welding. |
| 2 | Buy Back existing Air Walker from site ( Including taking out from Cement concrete). |
| 3 | Providing and installing a Sit Up Station at the site as per the specifications mentioned below: 1. Dimensions (LxWxH): 1500 x 1150 x 650mm 2. Fabricated with main frame of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 25mm (G.I.) ‘C’ Class Pipe. 4. Leg support of NB 65mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 5. Perforated MS Sheet for Back Support. 6. The back support Fixed on its top is made of perforated MS sheet of 2mm thickness. 7. All pipes are powder coated using Akzo Nobel or equivalent Paint of 80-120 micron thick. 8. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 9. Zinc primer paint is applied at all welding points prior to finishing. 10. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored.11. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 12. Once the concrete is set, the equipment is fixed on to it. 13. High tensile steel with galvanized nut bolts are used for assembly. 14. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. 15. Self-Explanatory stainless steel label fixed on equipment for ease of use. 16. Pipe and sheet components should be cut by laser machine having CNC made components welded with robotic welding. |
| 4 | Buy Back existing Sit Up Station from site ( Including taking out from Cement concrete). |
| 5 | Providing and installing a Leg Pressat the site as per the specifications mentioned below: 1. Dimensions (LxWxH):2000 x 550 x 1600 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Seat Main frame of NB 50mm (G.I.) ‘C’ Class Pipe and Pipe connecting main post to seat main frame of NB 65mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 6. Zinc primer paint is applied at all the welding points prior to finishing. 7. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 8. Foothold made of NB 50mm (G.I.) ‘C’ Class Pipe. 9. Seats made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 11. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 14. High tensile steel with galvanized nut bolts are used for assembly. 15. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.16. Self-Explanatory stainless steel label fixed on equipment for ease of use.17. Pipe and sheet components should be cut by laser machine having CNC made components welded with robotic welding. |
| 6 | Buy Back existingLeg Press from site ( Including taking out from Cement concrete). |
| 7 | Providing and installing an Arm Wheelat the site as per the specifications mentioned below: 1. Dimensions (LxWxH): 850 x 800 x 1800 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Wheel frame of NB 32mm with connecting spokes of NB 25mm, Pipe connecting main pilar with wheel frame of NB 50mm. All pipes must be (G.I.) ‘C’ Class Pipes. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 6. Zinc primer paint is applied at all the welding points prior to finishing. 7. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 8. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 9. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 10. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 11. High tensile steel with galvanized nut bolts are used for assembly. 12. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. 13. Self-Explanatory stainless steel label fixed on equipment for ease of use. 14. Pipe and sheet components should be cut by laser machine having CNC made components welded with robotic welding. |
| 8 | Buy Back existing Arm Wheel from site ( Including taking out from Cement concrete). |
| 9 | Providing and installing a Double Cross Walker at the site as per the specifications mentioned below: 1. Dimensions (LxWxH): 1600 x 600 x 1600 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Handle main frame of NB 50mm and other connecting pipes of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 4. Foot support frame of 96 x 46 x 3mm MS rectangular pipe. 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored. 9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 11. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.14. High tensile steel with galvanized nut bolts are used for assembly. 15. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. 16. Self-Explanatory stainless steel label fixed on equipment for ease of use. 17. Pipe and sheet components should be cut by laser machine having CNC made components welded with robotic welding. |
| 10 | Buy Back existing Double Cross Walker from site ( Including taking out from Cement concrete). |
| 11 | Providing and installing a Twister (Triple Standing) at the site as per the specifications mentioned below: 1. Dimensions (LxWxH): 1300 x 1300 x 1650 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Handle Main frame of NB 32mm (G.I.) ‘C’ Class Pipe. 4. Handle frame spokes of NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 5. Foothold plate of made of MS Sheet Metal of 3mm thickness. 6. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 7. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 8. Zinc primer paint is applied at all the welding points prior to finishing. 9. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 10. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 11. Once the concrete is set, the equipment is fixed on to it. 12. High tensile steel with galvanized nut bolts are used for assembly. 13. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment. 14. Self-Explanatory stainless steel label fixed on equipment for ease of use. 15. Pipe and sheet components should be cut by laser machine having CNC made components welded with robotic welding. |
| 12 | Buy Back existing Twister (Triple Standing) from site ( Including taking out from Cement concrete). |
| 13 | Providing and installing a Pull Chair at the site as per the specifications mentioned below:1. Dimensions (LxWxH): 2400 x 800 x 2000 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Seat main frame of NB 50mm (G.I.) ‘C’ Class Pipe, Pipe connecting main post with handle frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. Handle frame of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Handle bars are provided with high end quality rubber grips. 9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless steel label fixed on equipment for ease of use. 18. Pipe and sheet components should be cut by laser machine having CNC made components welded with robotic welding. |
| 14 | Buy Back existing Pull Chair from site ( Including taking out from Cement concrete). |
| 15 | Providing and installing a Seated Chest Press at the site as per the specifications mentioned below:1. Dimensions (LxWxH): 1800 x 700 x 2000 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Seat Main frame of NB 50mm (G.I.) ‘C’ Class Pipe. 4. Handle frame of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Handle bars are provided with high end quality rubber grips. 9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to GS Mark, EN 16630, DIN 79000, ASTM F 3101-15 and ISO 14001 International standard for outdoor fitness equipment.17. Self-Explanatory stainless steel label fixed on equipment for ease of use.18. Pipe and sheet components should be cut by laser machine having CNC made components welded with robotic welding. |
| 16 | Buy Back existing Seated Chest Press from site ( Including taking out from Cement concrete). |
| 17 | Providing and installing a Weight Assisted Shoulder Press at the site as per the specifications mentioned below: Weight Assisted Shoulder Press of minimum size 1350x1600x1150mm fabricated with main post ofG.I.‘C’ Class of NB 65 mm and othersupport and handle frames of NB 50 mm G.I. ‘ C’ Class pipes only. Joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing. Handle support frame made of GI \"C\" Class Pipe of NB 25 mm. Handle bars shall be provided with high quality rubber grip. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. Machine to have weight plate adjustment arrangement made of 304 grade stainless steel and it must be designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for the adjustment. Weight Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated of SKF / equivalent make as approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment shall be fixed on ground with concrete of minimum strength M-25 and J shape welded bolt made of 18mm galvanized rod and covered with base plate cover after the installation complete. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. Pipe and sheet components should be cut by laser machine having CNC made components welded with robotic welding. |
| 18 | Buy Back existing Weight Assisted Shoulder Press from site ( Including taking out from Cement concrete). |
| 19 | Providing and installing a Weight Assisted Chest Press at the site as per the specifications mentioned below: Weight Assisted Chest Press of minimum size 1100x1500x1300mm fabricated with main post ofG.I. ‘ C’ Class of NB 65 mm and othersupport and handle frames of NB 50 mm G.I. ‘ C’ Class pipes only. Joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint shall be applied at all welding points prior to finishing. Handle support frame made of GI \"C\" Class Pipe of NB 25 mm. Handle bars shall be provided with high quality rubber grip. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. Machine to have weight plate adjustment arrangement made of 304 grade stainless steel and it must be designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for the adjustment. Weight Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated of SKF / equivalent make as approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment shall be fixed on ground with concrete of minimum strength M-25 and J shape welded bolt made of 18mm galvanized rod and covered with base plate cover after the installation complete. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment. Self-Explanatory stainless steel label shall be fixed on equipment for ease of use. Pipe and sheet components should be cut by laser machine having CNC made components welded with robotic welding. |
| 20 | Buy Back existing Weight Assisted Chest Press from site ( Including taking out from Cement concrete). |
| 21 | Removing of damaged/ un-useable SBR Tiles from C:C Floor and disposed off as per direction & satisfaction of Engineer-In-Charge. |
| 22 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :(a) 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 23 | Part-B Maintaining 10 Nos of equipments in given park for a period of 2 year with complete maintenance of machine, repairing of parts etc. in allrespects as and when required, free of cost to the satisfaction of Engineer-in-Charge and as per condition given below:. |
| 24 | Condition:1.The agency will maintain all the 10 Nos. of equipments for two year.2.Nothing extra all the paid for new spare parts and maintenance and replacing the parts etc.3.The machines will be maintained with proper functioning and appearance i.e. with parts, paint and cosmetic treatment. The maintenance shall the following:-a) Inspection and adjustment of movable parts, nuts / bolts, alignment, lubrication / oiling / greasing etc., wherever required.b) Check and set right / replacement of worn out bearings, misaligned moving points, adjust / tighten loose parts, covers, seats, foundations, C.C. flooring, regular oiling and greasing etc.c) Tightening of nuts / bolts/ screws inspect / repair welding of various parts/ joints of equipments.d) Cosmetic treatment like priming and painting whenever required. e) Replacement of damaged parts and rectification of any other defects observed as per direction of Engineer-in-Charge except the following:- i) The defects due to force majeure.ii) Serious loss or damage by fire / earthquake / severe flooding / abnormally bad weather.iii) Any other incident which in the absolute discretion of the Engineer-in-Charge is beyond the control of the contractor.iv) Damage due to act of God.v) Theft / Vandalism.4. The agency will place contact phone number on each equipments during the complete maintenance period otherwise a penalty of Rs. 100/-per machine per week will be deducted from each bill.5. All the complaints must be attended/ resolved within a period of 5 Days otherwise a penalty of Rs. 1000/- per complaintper day shall be imposed.6. The regular maintenance is to be done with periodically checkup i.e. every week and an inspection report /record shall be submitted to Engineer-in-Charge on monthly basis by the agency. 7. 25% of gross bill amount of item no.1,3,5,7,9,11,13,15,17,19 will be withheld on account of maintanance in each running and final bill of part A. 10% of withheld amount as mentioned above can be released after 1 years of completion ofPart-A and the rest will be released after completion of Part-B. |
| 25 | TOTAL (DSR Items) 37,817.00 |
| 26 | Add GST Factor @ 0.973 on DSR item 36,796.00 |
| 27 | Add Cost index @ 3% on DSR item 37,900.00 |
