Tender For Ksdp-Maintenance And Repairing Work= Maintainence/ Rectification and Modification work of Non-Betalactum Plant, LVP-SVP and Administration Block 2 Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates,boltd, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. 3 Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge. 4 Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar 5 Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposedearth to be levelled and neatly dressed.All kinds of soil 6 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 7 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters andtrusses and including cutting to size and shape wherever required. 8 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) 9 Suppling and Fixing 10 Kgf/cm² Polyvinyl Chloride (PVC) pipes for internal/external work including all fittings, fixing the pipe with clamps at 1.00 m spacing, jointing of pipes using PVC Solvent cement and testing of joints, labour charges, hire charges of all tools and plants etc. complete as directed by the officersconcerned. 20 mm dia pipe 10 Suppling and Fixing 10 Kgf/cm² Polyvinyl Chloride (PVC) pipes for internal/external work including all fittings, fixing the pipe with clamps at 1.00 m spacing, jointing of pipes using PVC Solvent cement and testing of joints, labour charges, hire charges of all tools and plants etc. complete as directed by the officers concerned. 25 mm dia pipe 11 Suppling and Fixing 10 Kgf/cm² Polyvinyl Chloride (PVC) pipes for internal/external work including all fittings, fixing the pipe with clamps at 1.00 m spacing, jointing of pipes using PVC Solvent cement and testing of joints, labour charges, hire charges of all tools and plants etc. complete as directed by the officersconcerned. 50 mm dia pipe 12 Suppling and Fixing 10 Kgf/cm² Polyvinyl Chloride (PVC) pipes for internal/external work including all fittings, fixing the pipe with clamps at 1.00 m spacing, jointing of pipes using PVC Solvent cement and testing of joints, labour charges, hire charges of all tools and plants etc. complete as directed by the officersconcerned. 60 mm dia pipe 13 Suppling and Fixing 10 Kgf/cm² Polyvinyl Chloride (PVC) pipes for internal/external work including all fittings, fixing the pipe with clamps at 1.00 m spacing, jointing of pipes using PVC Solvent cement and testing of joints, labour charges, hire charges of all tools and plants etc. complete as directed by the officersconcerned. 75 mm dia pipe 14 Dismantling and removing the damaged L/J hook or SD screw and providing new L/J hooks or SD screw with bitumen washer and plate washer etc. complete as per instruction of company representative. 15 Cleaning the existing damaged surface of Non AC /Galvalume Profile sheet and supplying and fixing of Omega butyl aluminium flashing leak arresting tape of thickness 1.5 mm on the L/J hook or SD screw etc. complete as per the instruction of company representative 16 Cleaning the surface of damaged Non AC/ Galvalume Profile sheet, supplying and fixing omega butyl aluminium flashing tape of thickness 1.5 mm of required length as per the instruction of company representative 17 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturers specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work 18 Supplying and fixing of 600 mm sweep,900 rpm 4 blade single phase wall mounted, heavy duty exhaust fan along with all mounting accessories and installation of the same on wall as required. Make-Crompton/Almonard/Usha/Bajaj. 19 Providing and fixing anodised aluminium grill ( anodised transparent or dyed to required shade according to IS : 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P brass/stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, allcomplete as per requirement and direction of Engineer-in-charge.(Only weight of grill to be measured for payment ).
