Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 19-05-2025 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 26-05-2025 |
| Sl. No. | Item Description |
| 1 | Taking down cement plaster on brick or concrete surfaces including raking out joints, hacking for key scrubbing down with water etc. complete all as specified and directed by Engineer-in-Charge. |
| 2 | Demolition of brickor stone/boulders masonry, built in cement mortar complete all as specified and directed by Engineer-in-Charge. |
| 3 | Demolition of cement concrete in ground floors and paving n.exe 15 cm thick below or above ground level complete all as specified and directed by Engineer-in-Charge. |
| 4 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store complete all as specified and directed by Engineer-in-Charge. |
| 5 | Demolition of reinforced cement concrete of any descriptioncomplete all as specified and directed by Engineer-in-Charge.(Note: reinforcement cut as required to facilitate demolition ) |
| 6 | Taking down chowkhats or frames with shutters (without taking off shutters from the frame) n/exe 1.50 Sqm each complete all as specified and directed. Removing to or from store complete all as specified and directed by Engineer-in-Charge. |
| 7 | Taking down shutter of anydescription exe 1.00 sqm but n.exe 2.00 sqmeach complete all as specified and directed by Engineer-in-Charge. |
| 8 | Taking down shutters of anydescription n.exe 1.00 sqm each complete. Removing to or from store complete all as specified and directed by Engineer-in-Charge. |
| 9 | M&L forbrick work with sub class ‘B’ brick straight or curved on plan exceeding 6m mean radius in CM 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 10 | M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:4finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 11 | M&L for rendering 15 mm thick in cement mortar 1:6finishingon brick or concrete surfaces, finishing the surface even & smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 12 | M&Lfor RCC (nominal mix) (1:2:4) type B1 (using 20 mm graded crushed stone aggregate) as in slabs supported on walls, beams, and columnsetc. complete all as specified and directed by Engineer-in-Charge. |
| 13 | Form work to soffits of suspended slabs such as roof slabs, floors, slabs , landing and similar works etc. complete all as specified and directed by Engineer-in-Charge. |
| 14 | Form work to edge of concrete, flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs n. exc 20cm wide and sides of RCC/PCC bands in walls, slabs etc horizontal or sloping and similar works exc 10cm but n exc 20 cm wide complete all as specified and directed by Engineer-in-Charge. |
| 15 | M&L for mild steel TMT bars10mm dia and over cut to length bent to shape required including cranking bending spirally for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed by Engineer-in-Charge. |
| 16 | M&Lfor 25 mm thick PCCtype B0 (1:2:4) using 12.5 mm graded crushed stone aggregate as in floorto receive floor finishes etc. complete all as specified and directed by Engineer-in-Charge. |
| 17 | S&F vitrified ceramic dark shade/double charged/ultra charged/Granite /Marble /wood textures coloured tiles10mm thick (square/rectangular) polished, area of each tiles exc. 0.36 sqm but n. exc 0.42 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge. |
| 18 | M&L for Non skid ceramic coloured joint free tiles 7 to 8mm thick (square/ rectangular), area of each tiles exceeding 0.11 sqm but n exc 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles, laid over and including cement screed bed 15 mm thick in cement mortar (1:6) for laying floor finish complete all as specified and directed by Engineer-in-Charge. |
| 19 | M&L for Non skid ceramic coloured joint free tiles 7 to 8mm thick (square/ rectangular), area of each tiles exceeding 0.06 sqm but n. exc 0.11 sqm, in floor etc. set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tiles, laid over and including cement screed bed 15 mm thick in cement mortar (1:6) for laying floor finish complete all as specified and directed by Engineer-in-Charge. |
| 20 | M&L for glazed ceramic coloured tiles in vertical surfaces 350 x250x7/ 450x350x7 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10mm thick cement plaster in cement mortar (1:4)complete all as specified and directed by Engineer-in-Charge. |
| 21 | M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in cement mortar 1:3finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 22 | M&L for treatment to sunken slab by applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cum per sqm complete all as specified and directed by Engineer-in-Charge. |
| 23 | M&L for polyethylene film, 150 micron thick, laid on a coat of bitumen primer @ 0.30 to 0.50 kg per sqm complete all as specified and directed by Engineer-in-Charge. |
| 24 | M&L for 100mm thick PCC 1:2:4 type B1 using 20mmgraded crushed stone aggregate as in padding of sunken slabs etc. to required slope in sunken floor, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge. |
| 25 | M&L for kota stone slab flooring 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over and including 15mm thick screed bed in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge. |
| 26 | All as per item No. 25 above but on vertical surfaces of walls /skirting/dado etc.over and including 10mm thick cement plaster in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 27 | M&L in repairs for 20mm thick pre-polished graniteslabs, machine cut, in vertical/horizontal surfaces includingover and including 15mm cement plaster in cement mortar (1:4) and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of the granite stone including grinding and polishing complete all as specified and directed by Engineer-in-Charge. |
| 28 | S&F Factory made solid PVC door frame of size 50mm x 47mm made out of 5 mm single side pre-laminated PVC sheet reinforced with MS square tube manufactured as per SSR Part-I specifications and drawings complete all as specified and directed by Engineer-in-Charge. |
| 29 | S&F factory made solidPVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC \"C\" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail and bottom rail on either side and gap insert for top rail and bottom rail panelling of plain colour PVC to sheet to be fitted in the MS frame welded / sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and directed by Engineer-in-Charge. |
| 30 | S&F 2ndclass hard wood 40 mm thick panelled shutter Plain framed, panelled shutter (one panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated and fixed to chowkhats complete all as specified and directed by Engineer-in-Charge. |
| 31 | Supply and fixed 35mm thick 2ndclass hard woodglazed and skeleton shutters open rebated and prepared to receive glass, gauge etc. (internal sash bars) edges of framing plane, chamfered or rounded fitted and mitred beads for securing glass etc size of members as specified in SSR Part-I Section 8 clause8.24(a)(kail) complete all as specified and directed by Engineer-in-Charge. |
| 32 | S&F for30 mm thick 2nd class hard woodglazed and skeleton windows/ ventilators shutters open rebated and prepared to receive glass, gauge etc, divide into square with plain chamfered or rounded, mitred and rebated sash bars any numbers , provided with stiles and rails as specified in SSR part I section 8 clause 8.24 (b) complete all as specified and directed by Engineer-in-Charge. |
| 33 | S&F aluminium anodised barrel tower bolts extruded section of size 150 mm long complete all as specified and directed by Engineer-in-Charge. |
| 34 | S&F aluminium anodised barrel tower bolts extruded section of size 200 mm complete all as specified and directed by Engineer-in-Charge. |
| 35 | S&F aluminium alloy, anodised, sliding door bolt of length 300 mm with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts ofsections or cast-aluminium extruded alloy and fixed complete all as specified and directed by Engineer-in-Charge. |
| 36 | S&F butt hinges 75 mm medium weight cold rolled mild steel complete all as specified and directed by Engineer-in-Charge. |
| 37 | S&F mild steel rat tail spring including roller & roller plate complete 300 mm size complete all as specified and directed by Engineer-in-Charge. |
| 38 | S&F 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and directed by Engineer-in-Charge. |
| 39 | S&F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and directed by Engineer-in-Charge. |
| 40 | S&F in repairsgalvanised mild steel wire cloth, 0.56 mm nominal dia of wire and avrage width of aparture 1.18 mm complete all as specified and directed by Engineer-in-Charge. |
| 41 | S&F aluminium handle extruded fabricated type anodised of size 150 mm complete all as specified and directed by Engineer-in-Charge. |
| 42 | S&F forbutt hinges 100mm medium weight cold rolled mild steel complete all as specified and directed by Engineer-in-Charge. |
| 43 | M&L for fixed in repairs4mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane including hacking out old glass panes complete all as specified and directed by Engineer-in-Charge. |
| 44 | M&L 4mm thick sheet glass ordinary quality and glazing with oil putty or fixed with bead/glazing pins in squares n.exc 0.5 Sqm in each pane complete all as specified and directed by Engineer-in-Charge. |
| 45 | Dismantling water storage tanks of any description, exc 250 & n.exc 500 litres capacity and removing from site complete all as specified and directed by Engineer-in-Charge. |
| 46 | S&F for Rotational moulded polyethylene 500 litres capacity waterstorage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20 mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball complete all as specified and directed by Engineer-in-Charge. |
| 47 | S&F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connections of flush pipe to squat pattern closet including lime concrete bedding and all joint making good to the floor complete all as specified and directed by Engineer-in-Charge. |
| 48 | S & F in repairs vitreous chinabowl urinal flat back, size of 465 x 355 x 265 mm white (min), with grating and union for discharge pipeincluding connection to flushing system, flush pipe & waste pipe) complete all as specified and directed by Engineer-in-Charge. |
| 49 | S&F in repairs stain less steel gratings, 125mm dia complete all as specified and directed by Engineer-in-Charge. |
| 50 | S&F in repairs PVC valve less 10 litre capacity syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed by Engineer-in -Charge. |
| 51 | S&F in repairs Vitreous chinawash hand basin,Vitreous chinawhite, flat back, size 550 x 400 mm with brackets, including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed. (Including S&F 15mm bore CP pillar tap, waste coupling and 32mm dia PVC waste pipe) complete all as specified and directed by Engineer-in -Charge. |
| 52 | S&F in repairs 15 mm size PVC connection with PTMT nuts, 600 mm long complete all as specified and directed by Engineer-in -Charge. |
| 53 | S&F in repairs swivel shower of PTMT any colour with arm, 195 mm long with bend of 45 degree with flange (both min wt 80 gms ) complete all as specified and directed by Engineer-in -Charge. |
| 54 | S&F 110 PVC WC connector bent typecomplete all as specified and directed by Engineer-in -Charge. |
| 55 | S&F castiron Nahani trap 75 mm dia including jointing to pipe complete all as specified and directed by Engineer-in -Charge. |
| 56 | S&F in repairs 15 mm bore, chromium plated fancy typeCP bib tapscast copper alloy with crutch or butterfly handle, screwed down for iron pipe complete all as specified and directed by Engineer-in -Charge. |
| 57 | S&F in repairs, 15 mm bore CPstop valve cast copper alloy screwed down, high pressure with crutch or butterfly handlefancy typecomplete all as specified and directed by Engineer-in -Charge. |
| 58 | S&F in repairs, 15 mm bore CP fancy type stop valve, chromium plated with long shank and cup (concealed type) cast copper alloy screwed down, high pressurefancy typecomplete all as specified and directed by Engineer-in -Charge. |
| 59 | S&F600 x 450mm bevelled edge mirror of selected quality glass mounted on 6mm thick PVC sheetand 3 mm th PVCmoulded framearound the glass with chromium plated brass screws and cup washers includingprovision of hanging hooks and S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet, 12 cm wide and 600mmlong with chromium plated brackets guard and railing complete all as specified and directed by Engineer-in -Charge. |
| 60 | Taking upor down 15mm bore GI Tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in -Charge. |
| 61 | Taking upor down 20mm dia GI Tubing and connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in -Charge. |
| 62 | S&F 15 mm bore GI tubing medium grade galvanised with all fittings and fixed complete to walls & floors etc. complete all as specified and directed by Engineer-in -Charge. |
| 63 | S&F 20mm bore GI tubing medium grade galvanised with all fittings and fixed complete to walls & floors etc. complete all as specified and directed by Engineer-in -Charge. |
| 64 | S&F in repairs brass chromium plated tubular towel rail with brackets, 20mm dia, D type, 60 cm long between flanges complete all as specified and directed by Engineer-in -Charge. |
| 65 | S&F in repairs vitreous china wash down water closet pan ( pedestal pattern ) white complete including ‘P’ or ‘S’ trap , seat cover and fixing to flushing cistern, brackets, flushing pipeetc. complete all as specified and directed by Engineer-in -Charge. |
| 66 | S&F in repairs 15 mm borebrass CP mixer for mixing hot and cold waterscrewed down high pressure with long screwed shanks and fly nuts screwed for iron pipes complete all as specified and directed by Engineer-in -Charge. |
| 67 | S&F in repairs Ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for 20mm dia iron pipe and fixed (minimum weight for 15mm-142gms/20mm 210gms/25mm - 455gms/40mm - 690gms) complete all as specified and directed by Engineer-in -Charge. |
| 68 | S&F in repairsPillartap 15mm chromium plated fancy type cast copper alloy with crutch or butter fly handle, screwed down for iron pipe and fixed complete all as specified and directed by Engineer-in -Charge. |
| 69 | S&F in repairsbibtap 15mmPTMT any colour high pressure screwed down for iron pipe and fixed ( Minimum weight 90gms) complete all as specified and directed by Engineer-in -Charge. |
| 70 | S&F in repair 20 mm bore gun metal globe or gate valve with iron wheel head screwed head both for iron pipe & fixed complete all as specified and directed by Engineer-in -Charge. |
| 71 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed by Engineer-in -Charge. |
| 72 | S&F 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls/floor complete all as specified and directed by Engineer-in -Charge. |
| 73 | S&F 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed on walls/floor complete all as specified and directed by Engineer-in -Charge. |
| 74 | S&F 75mm PVC (SWR) bends any radius complete all as specified and directed by Engineer-in -Charge. |
| 75 | S&F 110mm PVC (SWR) bends any radius complete all as specified and directed by Engineer-in -Charge. |
| 76 | S&F 110mmPVC (SWR) vent cowl complete all as specified and directed by Engineer-in -Charge. |
| 77 | S&F 75mm PVC (SWR) vent cowl complete all as specified and directed by Engineer-in -Charge. |
| 78 | S&F for Hollow PVC wall panelling decorative typeconsisting of 8 mm thick plain colour PVCpre-laminated sheet inclusive of solvent cement and fixing at site on PVC frame/wooden frame as per specification and drawing complete all as specified and directed by Engineer-in -Charge. |
| 79 | S&F for 5 mm thick PVC sheet fillets of width 35 mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified and directed by Engineer-in -Charge. |
| 80 | Dismantling plain or corrugated steel sheeting any gauge, thickness including roof covering etc. complete all as specified and directed by Engineer-in -Charge. |
| 81 | M&L for Pre-painted galvalume aluminium zinc coating Gi based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed by Engineer-in -Charge. |
| 82 | M&L for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof ridge etcfixed with self tapping screws complete all as specified and directed by Engineer-in -Charge. |
| 83 | M&L for 50 mm thick PCC ( 1:3:6) type C-2 using 40mm grade crushed stone aggregate as in plinth protection etc complete all as specified and directed by Engineer-in -Charge. |
| 84 | M&L for preparing plastered or un plastered NEW surface of walls and applying two coats of Cement base paint on walls over a coat of alkali-resistant primer complete all as specified and directed by Engineer-in -Charge. |
| 85 | M&L for applying3 mm thick wall care putty on wallincluding preparation new surfaces plastered or unplasteredsurfaces complete all as specified and directed by Engineer-in -Charge. |
| 86 | M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of Primer on plastered and other surfaces with alkaliresistant priming paint complete all as specified and directed by Engineer-in -Charge. |
| 87 | M&L for preparing plastered or un plastered new surface of walls and applying three coats of white wash on walls complete all as specified and directed by Engineer-in -Charge. |
| 88 | M&L for preparing plastered or un plastered OLD SURFACES of walls and applying two coats of Cement base paint on walls (External)including complete removal of existing treatment complete all as specified and directed by Engineer-in -Charge. |
| 89 | Material and labour for applying one coat of cement base paint to old treated plastered or un-plastered surfaces of wall including preparation of surfaces (by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots) complete all as specified and directed by the Engineer-in-Charge. |
| 90 | Material and labour for applying one coat of OBD to old treated surfaces of wall including preparation of old surface of walls (by washing down, rubbing down and stopping of distempered surface) complete all as specified and directed by the Engineer-in-Charge. |
| 91 | Material and labour preparation of old painted wooden surfaces and applying one coat of synthetic enamel paint of any description, not otherwise described, over 10 cm width or girth including preparation of surfaces complete all as specified and directed by Engineer-in -Charge. |
| 92 | M&L for preparation of old decorated CGI Sheet surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint (in camouflage/plain pattern) complete all as specified and directed by Engineer-in -Charge. |
| 93 | Material and labour for applying one coat of white washto old treated plastered or un-plastered surfaces of wall including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots) complete all as specified and directed by the Engineer-in-Charge. |
| 94 | Material and labour for applying one coat of white washto old treated plastered or un-plastered surfaces of ceilling including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots) complete all as specified and directed by the Engineer-in-Charge. |
| 95 | M&L for preparation of old surfaces of wall and applying two coats of cement base paint complete as per manufactures instructions and directed by Engineer-in-charge. |
| 96 | Material and labour for complete removal of existing treatment of old surface of wall and applying two coat of oil bound distemper over a coat of alkali resistant primer including application of 1mm thick wall care putty complete all as specified and directed by the Engineer-in-Charge. |
| 97 | Material and labour for applying two coat of synthetic enamel paint to old painted wooden surfaces of any description, not otherwise described, over 10 cm width or girth including preparation of surfaces complete all as specified and directed by Engineer-in -Charge. |
| 98 | M&L for preparation of old decorated CGI Sheet surfaces of any descrption not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint (in camouflage/plain pattern) complete all as specified and as directed. |
| 99 | Taking down copper/aluminium point wiring light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting conduit/casing capping etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed by Engineer-in-Charge. |
| 100 | M&L for Point wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi stranded flexible cable and 1.5 sqmm PVCinsulated unsheathed copper conductor single core cable (green color) as earth lead in and including PVC casing and capping/Conduit mediumgrade of suitable size run on wall/surface with all fittings (ISI Marked) controlled by one switch including CI/MS sunk box of required size or PVC Gang Box& 3mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with theexisting specification complete all as specified and directed by Engineer-in-Charge. |
| 101 | All as per srl item No-100 here in above but for one 3 pin 5A socket outlet independent controlled by one switch complete all as specified and directed by Engineer-in-Charge. |
| 102 | All as per srl item No-100 here in above but for one 5A socket outlet on the same board controlled by one switch complete all as specified and directed by Engineer-in-Charge. |
| 103 | All as per srl item No-100 here in above but for one 3 pin 15 Amps socket outlet on independentboard with 2.5 sqmm PVCinsulated unsheathed copper conductor single core multi strand flexible cable and 2.5 Sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green color) as earth lead. |
| 104 | M&L forsubmain wiring with two singlecore PVC insulated flexible copper conductor cable of size 4 sqmm and one single core PVCinsulated flexible copper conductor cable green colour of size 4 Sqmm as earth lead in & including concealed PVC casing capping/conduit medium grade2mm thickness ISI marked or cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification including taking down old unserviceable submain wiring complete all as specified and directed by Engineer-in-Charge. |
| 105 | M&L forsubmain wiring with two singlecore PVC insulated flexible copper conductor cable of size 6 sqmm and one single core PVC insulated flexible copper conductor cable green colour of size 6 Sqmm as earth lead in & including concealed PVC casing capping/conduit medium grade2mm thickness ISI marked cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification including taking down old unserviceable submain wiring complete all as specified and directed by Engineer-in-Charge. |
| 106 | M&L for Switch piano flush button single pole one way 5 amps 240 voltscomplete all as specified and directed by Engineer-in-Charge. |
| 107 | M&L forSwitch Socket combination, 6 pin 5 and 15 amps multi purpose 2 in 01 flush type, 230 volts complete all as specified and directed by Engineer-in-Charge. |
| 108 | M&L for Switch Socket combination 2 in 1, 5 Amps flush type, 230 volts complete all as specified and directed by Engineer-in-Charge. |
| 109 | M&L for Socket2 in 1, 5 Amps flush type, 230 volts complete all as specified and directed by Engineer-in-Charge. |
| 110 | M&L for Socket5/15 amps flush type, 230 volts complete all as specified and directed by Engineer-in-Charge. |
| 111 | M&L for Ceiling rosesurface Bakelite 2 to 3 terminals complete all as specified and directed by Engineer-in-Charge. |
| 112 | M&L for Switch piano flush button single pole one way 15 amps 240 voltscomplete all as specified and directed by Engineer-in-Charge. |
| 113 | Supply and fixing for fan regulator electronic, step type hum free suitable to control speed of fan from 0 to 100% and connecting electrically complete all as specified and directed by Engineer-in-Charge. |
| 114 | S&F for Lamp holder insulated body with back plate for batten fittingscomplete all as specified and directed by Engineer-in-Charge. |
| 115 | S&F for bell push flush type 6 Amps 240 Voltcomplete all as specified and directed by Engineer-in-Charge. |
| 116 | S&F for bell/buzzer AC 230 volts single polecomplete all as specified and directed by Engineer-in-Charge. |
| 117 | Supply and fixing for Plug top 3 pin 15 amps 230 volts including taking oldplug top complete all as specified and directed by Engineer-in-Charge. |
| 118 | Supply and fixing for Plug top 3 pin 5 amps 230 volts including taking oldplug top complete all as specified and directed by Engineer-in-Charge. |
| 119 | Supply & fix for Rigid non-metallic PVC conduit of size 20 mm dia, exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified and directed by Engineer-in-Charge. |
| 120 | Supply & fix Rigid non-metallic PVC conduit of size 25 mm dia, exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etccomplete all as specified and directed by Engineer-in-Charge. |
| 121 | Supply & fix for medium gradePVC casing and cappingof size 20 mm dia, exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc complete all as specified and directed by Engineer-in-Charge. |
| 122 | Supply and fixing (in repair)PVC Gang box surface type suitable for fixing of 5 pin 15 Amp multipurpose switch socket on wall complete all as specified and directed by Engineer-in-Charge. |
| 123 | Supply and fixing (in repair)PVC Gang box surface type suitable for fixing of 5 pin 5 Amp multipurpose switch socket on wall complete all as specified and directed by Engineer-in-Charge. |
| 124 | Supply and fix in replacement cable PVC FRinsulated unsheathed with flexible multi stranded copper conductor of size1.5 Sqmm 1100 Volts grade as per site requirement of existing colour coding adopted complete all as specified and directed by Engineer-in-Charge. |
| 125 | Supply and fix in replacement cable PVC FRinsulated unsheathed with flexible multistranded copper conductor of size2.5 Sqmm 1100 Volts grade as per site requirement of existing colour coding adopted complete all as specified and directed by Engineer-in-Charge. |
| 126 | Supply and layingin replacement1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circulartwin core4 sq. mmcomplete all as specified and directed by Engineer-in-Charge. |
| 127 | Supply and layingin replacement1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circulartwin core6 sq. mmcomplete all as specified and directed by Engineer-in-Charge. |
| 128 | Supply and layingin replacement1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circulartwin core10 sq. mmcomplete all as specified and directed by Engineer-in-Charge. |
| 129 | Supply and layingin replacement1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circulartwin core16 sq. mmcomplete all as specified and directed by Engineer-in-Charge. |
| 130 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge. |
| 131 | S&F LED lights fitting 1x20W, 230V, AC decorative box type with drive, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engineer-in-Charge. |
| 132 | Taking down old Unserviceable Bldg Security light fitting and taken as credit including supply & Fixing building security light fitting LED 25 Watt new generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP65 roadway luminaries with high power LED as light source along with suitable bracket incl all accessories complete all as specified and directed by Engineer-in-Charge.Make: Havells, Cat Part No: ENDURAPEARLSL25WLED 757SASYTOPCor equivalent in PHILIPS CAT PART NO BRP042 LED 19 CW MR SI PSU GR OR C&S CAT PART NO DRACO/25W LTESS25WLED |
| 133 | Taking down old/UNSV Flood lightsand S&F LED Flood light of 30 watt Energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium flood light with high power LEDs as light source, suitable for highlighting architectural features or Area Lighting. Also suitable to rough services/installationscomplete with all accessories etc including connecting with threecore twisted flexible copper conductor cable with suitable sizecomplete all as specified and directed by Engineer-in-Charge.Make:Havell cat part No JETA QUANTOPLUSFLP30WLED757SYMLENS or equivalent /Bajaj/CG |
| 134 | Supply and fixing LED luminaire 600 mm x 600 mm, 36 watt ( White/ Warm White) , 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed by Engineer-in-Charge. |
| 135 | Supply, Installation, testing and commissioning of Energy Efficient LED surface 2x2 luminaire 36 wattfitting ( warm white/ white )glare free soft illumination White powder coated CRCA housing with seamless front frame with flat non-yellowish diffuser,including necessary connection from ceiling rose to fitting with flexible copper cable of suitable size/core all as specified and as directed. Make:Bajaj cat part No BZSSQL 36W LED WH i or equivalent /Havells/CG/SYSKA Surface mounted LED luminary with full glow designed luminary > 30% energy saving, maintenance free, CRI 80, System consumption should be between 28- 36W complete all as specified and directed by Engineer-in-Charge.Make: PHILIPS CAT. No. SM 365C LED 32-6500 PSU OD GR or Havells Cat Part No PLUTO SURFACE 2X2 PLS34W LED 84 OS or C&S CAT PART NO . CYGNUS-CS/36W/2X2/W-LTCSP36W LED 2X2 |
| 136 | Supply and fix sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 4 way, including suitable size copper bus bar and neutral linkfixed flush in wall including making chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed by Engineer-in-Charge. |
| 137 | Supply and fix MCB Distribution board , 240 volts single pole andneutral ,double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 8 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed. |
| 138 | Supply and fix MCB Distribution board , 240 volts single pole andneutral ,double door, sheet steel, enclosure powder coated with 100 Amps rated busbar with neutral link, 12 ways , fixed on wall duly grouted in solid block wall or on wooden board with electrical connection complete all as specified and directed by Engineer-in-Charge. |
| 139 | Supply and fixing 240V, 10 KA \"B\" curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 Amps in the MCB DB Complete with connection testing and commissioning complete all as specified and directed by Engineer-in-Charge. |
| 140 | Supply and fixing 240V, 10KA \"B\" curve miniature circuit breaker (MCB) ofcurrent carryingSPN 32 Amps capacity in the MCB DB complete with connection testing and commissioningcomplete all as specified and directed by Engineer-in-Charge. |
| 141 | Supply and fixing 240V, 10KA \"C\" curve miniature circuit breaker (MCB) ofcurrent carryingSPN 40-63Amps capacity in the MCB DB complete with connection testing and commissioningcomplete all as specified and directed by Engineer-in-Charge. |
| 142 | Supply and fixing 415V 10KA \"B\" curve miniature circuit breaker (MCB) ofcurrent carrying capacity TPN40 to 100 Amps in the DB complete with connection testing and commissioning complete all as specified and directed by Engineer-in-Charge. |
| 143 | Supply and fix MCCB 4 Pole, 415 V, Adjustable type, 100 Amps with breaking capacity 16 KA complete all as specified and directed by Engineer-in-Charge. |
| 144 | M&L painting of ceiling fan complete, using spray gun, in site with synthetic enamel paint by spraying including filling cavities with filler , one coat after cleaning all dust complete all as specified and directed by Engineer-in-Charge. |
| 145 | S&F in replacement of capacitor 2/3.15 mfdAC 230 volts50 Hz complete all as specified and directed by Engineer-in-Charge.Make : Asian/Jyoti/Usha /Apcos |
| 146 | S&F in replacement of capacitor 4 mfdAC 230 volts50 Hz complete all as specified and directed by Engineer-in-Charge.Make : Asian/Jyoti/Usha /Apcos |
| 147 | S&F in replacement of ball bearing for ceiling fan /exhaust fan any size any makecomplete all as specified and directed by Engineer-in-Charge.Make : SKF/NBC/ABC. |
| 148 | S&F in replacement of gun metal bush with suitable size, gun metal bush for ceiling fan any make, any size and sweep complete all as specified and directed by Engineer-in-Charge. |
| 149 | M&L for rewinding of AC ceiling fan/wall mounting fan motor as existing at siteany make with super enamelled copper winding wire any gauge from 0.315mm to 0.193mm including cutting of old burnt winding, Sleeve work varnishing with `B\" class insulation varnish, connection with flexible wire of appropriate size two core copper wire upto connector block qty of copper winding wire not less than 350 grms and not more than 500 grms per fan motor , replacement of capacitor 2 mfd, complete all as specified and directed by Engineer-in-Charge. |
| 150 | M&L for rewinding of exhaust fan motor any size, from 225 to 300 mm sweep with supper enamelled copper wire of any size ranging from 0.500mm to 0.285 mm including necessary cutting of old burnt winding wire, cleaning of slots and provision of necessary threading/sleeve work and taking out connection in lead with PVC copper wire of appropriate size upto connector block, capacitor 2/3.15 mfdcomplete all as specified and directed by Engineer-in-Charge. |
| 151 | Taking down carefully geyser 25/35/50 ltrs capacity from wall after unscrewing nuts/bolts etc. and again refixing in position after repairs and replacement of spare parts including testing complete all as specified and directed by Engineer-in-Charge.Note: (spare parts shall be measured and paid for separately under respective items) |
| 152 | M&L for in replacement of unserviceable heating element AC 230 Volt of rating 1500W ISI mark (triangular/round) as per existing any type complete all as specified and directed by Engineer-in-Charge. |
| 153 | M&L for replacement of unserviceable heating element AC 230 Volt of rating 2000W ISI mark (triangular/round) as per existing any type complete all as specified and directed by Engineer-in-Charge. |
| 154 | M&L for replacement of unserviceable thermostat switch AC 230 Volt adjustable range from 0-90 degree Celsius complete all as specified and directed by Engineer-in-Charge. |
| 155 | M&L for replacement of unserviceable Indicator lamp round/square type suitable for geyser 25-50 litres all as per sample AC 230 Volts complete all as specified and directed by Engineer-in-Charge. |
| 156 | M&L for replacement of unserviceable auto cut switch suitable for geyser 25-50 ltrs all as per sample AC 230 Volts complete all as specified and directed by Engineer-in-Charge. |
| 157 | M&L for replacement of unserviceable geyser assembly suitable for geyser 25-50 ltrs all as per sample AC 230 Volts complete all as specified and directed by Engineer-in-Charge. |
| 158 | Replacement of flexible PVC connection pipe heavy duty suitable for hot water to bear the temp of 100 degree centigrade with outlet and inlet connection brass adopters , washers of size 450 mm long 15 mm dia borecomplete all as specified and directed by Engr-in-Charge |
| 159 | Supply and fixing of LED7 watt pin type bulb complete all as specified and directed by Engineer-in-Charge. Make-Havells/Philips/Bajaj |
| 160 | Dismantling existing unserviceable hylam sheet of any size from boards removing switches etc.Supply and fix hylam sheet 3mm thick including necessary cutting of suitable opening for switches, sockets, regulators, etc refixing of switches, sockets, regulators, etc replacing screws and connecting up and testing complete all as specified and directed by Engineer-in-Charge. |
| 161 | Supply and install Decorative gate light made up of high grade unbreakable polycarbonate material suitable for retrofit LED lamp B22 base including 12 watt LED Lamp with necessary connection of suitable size copper cable complete all as specified and directed by Engineer-in-Charge.Make : - Havells Cat part No LHFXBON1TN6F035 or equivalent in Bajaj , Philips,Wipro |
| 162 | Supply and fixing LED Bulkhead7 watt ,designed for modern homes available in non PIR as well as PIR sensor with premium quality diffuser for glarefree light and easy to install snapfit installer with necessary connection of suitable size copper cable complete all as specified and directed by Engineer-in-Charge.Make : - Havells Cat part No LHEXCGP7IN5W006 or equivalent in Bajaj , CG |
| 163 | S&FPVC insulated and PVC Round Sheathed, Multicore annealed Bare Copper Conductor (flexible) industrial cable for Voltage Grade 1100 Volt 3 x 1.0 sqmmdrawn through polefrom junction box to security light fittingcomplete all as specified and directed |
| 164 | Material & labour for earthing complete with galvanised cast iron earth plate electrode of size 600x600x6.0mm thick buried directly in ground less than 3.0m deep below normal ground level as earth electrode with top edge of the earth plate not less than 2.25mtr below ground level using GI strip 32x6 mm dia as earth continuity conductor connected to earth plate by means of welding, GI thimbles, nuts, bolts & washers all as directed including providing earth wire protection pipe GI light grade15mm dia from earth plate to main switch board/panel, watering pipe 20mm dia with wire mesh and funnel at top, earth pit and RCC pit coverwith handle,angle iron frame of size 40 x 40 x 6mm in PCC 1:3:6 adequate quantity of charcoal dust and salt and kalmi shora all around the earth plate, earth work in any type of soil removing surplus excavated material all as required at site and specified in EP No 3 of SSR part I 2009 or directed by Engineer-in-charge and including testing on completion. (i) Main earthing lead from earth plate electrode to test point up to length of 7.5 meters length shalldeemed to be included in the unit rate quoted against this item .(ii) GI protection pipe & earthing lead beyond 7.5 meter shall be measured and paid for separately under appropriate item. (iii) On testing after completion if the desired resistance is not obtained the contractor shall redo the earthing without any extra cost to the department . |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
