C S Item On Conversion Supply Basis And Forged Steel Item , C.S Coupling Having Material As Per Is:1030 Grade 280-520W For Mill Size 30X60 As Per Drg. Supply Basis , Conversion Basis , Machining Charge , Cast Steel Crown Pinion Having Material Is:2708 Grade-Iii-B For Mill Size 30X 60 As Per Drg. Supply Basis , Conversion Basis , Machining Charge , C.S.Trash Plate Having Material As Per Is:1030 And Grade-Iii-B Supply Basis , Conversion Basis , Machining Charge , Teeth Cutting/Grooving Of Trash Plate As Per Drg. , C.S.Trash Beam As Per Is-1030/Is 2708 As Per Drg. Supply Basis , Conversion Basis , Machining Charge , Forge Steel Tail Bar For Taxmaco And Kcp Mill Having Material C-40/8 As Per Drg. Mh- 6 & Mh-56 Supply Basis , Conversion Basis , Forge Steel Pinion For Transmission Gear Of Taxmaco Mill As Per Drg. No. Mh 39,Material En-24,Tensile Strength70-80 Kg./Sqcm, Hardness 200-220 Bhn , C.S.Bearing Housing For Taxmaco Mill As Per Deg No Mh-17-C/04 Side Roller Housing Supply Basis , Conversion Basis , C.S.Bearing Housing For K.C.P.Mill As Per Drg No Mh-17-B Side Roller Housing Supply Basis , Conversion Basis , C.S.Bearing Housing Fork.C.P.Mill As Per Drg No Mh-17-B Top Roller Housing Supply Basis , Conversion Basis , C.S.Gear Coupling For C/F Machine As Per Drg.No.Bh-14 (Duly Case Hardness) , C.S. Pinion For Cane Unloader As Per Drg, Cu- 16 Teeth-17 , Teeth -18 , C.S.Sprocket 2 Pitch (Both Pilot Bore) (I) No Of Teeth 18 , Boss Dia 3 , (Ii) No Of Teeth 36 , Boss Dia 6 , C.S.Sprocket For Boiler Rotary Feederas Per Drg.Blr-73/1 Pitch- 25.0 Mm,No Of Teeth 21, Od -180Mm. P.B -25Mm , C.S.Sprocket For Bagasse Elevator(Pilot Bore) As Per Drg.Mh-75 Pitch 50.8 Mm,No Of Teeth 50, Od 842.70Mm. Pcd 808.7Mm,Teeth Thickness 28Mm , Boss- 270X130 Mm , Cs Sprocket (Pilot Bore ) As Per Drg.Blr-62Pitch 50.8 Mm, No.Of Teeth-14 Pcd 226.49Mm,Od 258.8Mm , Static Coller Of 25 Mm Thick Duly Hard Faced Of 5 Mm Thick Layer . Total Thick 30 Mm After Hard Facing For Taxmaco & Kcp Mill As Per Drawing No. Mm 105 (I) M.S. Material , (Ii) C.S.Material , Sprocket Of Inter Carrier Od 280 Mm,No.Of Teeth45.Pitch 19.5 Mm , C.S. Sprocket (Duplex) For Enter Carrier Teeth 12, As Per Drg. Mh-72/Sample , S.S. Wear Plate Is 304 Quality (I) Length 435 Mmx Width 370 Mmx Thick 15 Mm , (Ii) Length 385 Mm X Width 330 Mm X Thick 15 Mm , C.S.Tresh Beam Bracket As Per Sample /Drg. , C.S.Eccentric Pin Trash Bar Adjusting Device As Per Drg. Mh-133/2024-25 , C.S. Trash Beam Adjusting Connecting Rod For Taxmaco Mill, As Per Drg. Mh- 297 , C.S. Bridge Wheel For Cane Unloader As Per Drg. Cu25 (1), , Trolly Wheel For Cane Unloader As Per Sample /Drg. , Pinion Gear Set For Cane Unloader As Per Sample /Drg , C.S. Pinion (Gear) For Rbc Cross Carrier Pitch 41Mm. Teeth 25 , Type Of Teeth In Valute (Spur) Module 12.7 Mm Width 125 Mm .Od 343 Mm, Bore 2 Dia As Per Drg. , Clutch Shaft For Mill. As Per Drg. Mh-76 , En-8 For Taxmaco Mill -Sl.No.2 , For Kcp Mill - Sl.No.1 , Cs Worm For Crystilizer Wheel Od 290 Mm, Bore 81 Mm.Pitch 80 Mm Complete , Groving Of C.S. Trash Plate As Per Drg. , Idler Wheel Gear For Cane Unloader., No Of Teeth 68, Od-420 Mm, Module-6, Pitch- 18.84 Mm, Pcd-408 Mm, As Per Drg. No. Cu-25 (I) , Pinion For Cane Unloader No. Of Teeth- 33, Od-212 Mm, Pcd-198 Mm, Pitch- 18.84 Mm, Module-6 As Per Drg. No. , Pinion For Cane Unloader No. Of Teeth- 18, Od-200 Mm, Pitch- 35 Mm, Bore- 50 Mm, Width-115 Mm, Module-6, Teeth Depth-25 Mm As Per Drg. No. , Break Stand Complete For Cane Unloader, Size-10 , Cs Sprocket Of Rbc, Nos Of Teeth 12, As Per Drg. Blr 32/93 , Chain Sprocket For Inter Carrier Clucth Shaft, Od 280, Pcd 270, Bore 108, Root Dia 260, Nos Of Teeth 45, Nos Of Hole 4, As Per Drg. 001 , Pinion For Transmission Gear Kcp Mill, Material En-24 (As Per Drawing No. Mh-95/2024-25) , C.S. Helical Teeth Pinion, Teeth-20, Od-60, Bore-26, Pitch-10 (As Per Drawing No. Bh-Rg-05/2024-25) , C.S. Helical Teeth Pinion, Teeth-17, Od-62, Bore-28, Pitch-13 (As Per Drawing No. Bh-Rg-04/2024-25) , Chief Engineer
