|
| 1 | Demolition of cement concrete (reinforced) in ground floor and pavingn.exc 15 cm thick above or below ground level complete and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m complete all as specified and directed. |
| 2 | Taking downand removing chowkats with shutters (withouttaking off shutters from chowkat)not exceeding 1.50 Sqmeach complete all as specified and directed. |
| 3 | Taking down and removing chowkats with shutters (withouttaking off shutters from chowkat)exc 1.50 Sqmbut not exc 4.00 Sqm each complete all as specified and directed. |
| 4 | PCC 1:2:4 (nominal mix) type B-2(using 40mm graded crushed stone aggregates) as in roofkerbs or mud stops, rounded or chamfered on edges including necessary form work complete all as specified and directed. |
| 5 | RCC 1:2:4 (nominal mix) type B-1(using 20mm graded crushed stone aggregates) as in Slabs supported on walls, beams and columns in floors,roofs, landings, balconies, canopies, deck slabs and in shelves and the like, including demolition of RCC complete all as specified and directed. |
| 6 | Use & waste of form work to suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for fair finished surfaces of flat concrete, complete all as specified & directed. |
| 7 | Use & waste of form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cmwide for rough finished surfaces of concrete, complete all as specified & directed. |
| 8 | Brickwork with old size fly ash bricks, straight or curved on plan exc 6m mean radius, built in built incement mortar 1:6, including demolition og existing masonary and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m all as specified & directed. |
| 9 | Walling of random rubble stone masonry uncoarsedwell bonded bedded and soilidly hearted built in CM 1:6, including demolition og existing masonary and disposal of unserviceable material, debris and rubbish to a distance not exceeding 100m , complete all as specified and directed. |
| 10 | Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing as shown on page No176 to 183 of MES SSR 2020 Part-II compete all as specified and directed.(Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) |
| 11 | Powder coated, Anodised aluminium frame powder coated for doors, windows, ventilators with one or more rebates including joining cleat for fixing of glass, particle board,aluminium frame etc complete all as specified and directed. |
| 12 | Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails.M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Pane of 4 mm thick sheet glass to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable 5mm thick x15mm wide PVC sheet beading used inside stiles and rails anddecorative PVC beading of 10mm x 10mm (900 ), and joined together with solvent cement, suppling & fixing in the frame at site, complete as shown on page No176 to 183 of MES SSR 2020 Part-II compete all as specified and directed. |
| 13 | Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed. |
| 14 | Aluminium handles, cast type, anodised of size 150 mm complete all as specified and directed. |
| 15 | Aluminium anodizedbarrel tower bolt of extruded section of size 200 mm and fixed complete all as specified and directed. |
| 16 | 100mm size , Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodisedand fixed, type B-21, complete all as specified. |
| 17 | Galvanished mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanished wire staples complete all as specified and directed. |
| 18 | Sheet glass, 4.8mm thick ordinary quality and glazing with oil putty in squares n.exc 0.5 sqm each pane complete all as specified and directed. |
| 19 | Sheet glass, 3mm thick ordinary quality and glazing with oil putty in squares n.exc 0.5 sqm each pane, including hacking out old glasscomplete all as specified and directed. |
| 20 | 18mm thick PVC sheet having one side decorative laminated sheet as in brackets, fixed with ahesive and stainless steel screws whereverrequired, edges to be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per manufacturer specification includings all fittins suchs as magentic catcher , stainles steel handle , completeall as specified and directed. |
| 21 | Structural steel work as in Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc.. conforming to grade Fe 410 -W (Gde-E- 250) quality-Acomplete all as specified and as directed. |
| 22 | Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed. |
| 23 | Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) ofapproved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mmcentre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge. |
| 24 | 75mm thick PCC 1:4:8type D-2 (using 40 mm graded crushed stone aggregates)as in sub base complete all as specified and directed. |
| 25 | Mat finish, premium quality, joint free (edge cut), coloured/ printed ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in floors etc. set and jointed in neat cement slurry and including 15mm thick bedding layer in cement mortar (1:6) including necessary cutting and waste as per site requirement pointed in white or coloured cement to match including dismantling old tiles complete all as specified and directed. Size/Shade/Colour of tile shall be approved by the AGE(I). |
| 26 | Vitrified ceramic tiles (Dark shade) 10mm thick (square/rectangular) polished, area of each tile not exceeding 0.36 Sqm as directed by EIC, as in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 15mm thick screed bed in cement mortar 1:6 including dismantling old tiles complete all as specified and directed. |
| 27 | Glazed ceramic colouredtilesof size450 mm x 350 mm x7 mm thick as in vertical surfaces , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick cement screed in cement mortar 1:3 including dismantling old tiles complete all as specified and directed. Note : Size/Shade/Colour of tile shall be approved by the AGE(I). |
| 28 | Glazed ceramic colouredtilesof size300 mm x 200 mm x7 mm thick as in vertical surfaces , set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tile over and including 10 mm thick cement screed in cement mortar 1:3 including dismantling old tiles complete all as specified and directed. Note : Size/Shade/Colour of tile shall be approved by the AGE(I). |
| 29 | Marble work(of any type) work (table rubbed and polished) of any shade other than white and black , in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble including demolition of existing marble/ tilecomplete all as specified and directed |
| 30 | 20mm thick, Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, including demolition of existing marble/ tiles complete all as specified and directed. |
| 31 | Machine cut kota stone slab flooring 20-25 mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:6 including cutting, rubbing, grinding and polishing to achieve mirror finish complete, including demolition of existing flooring, complete all as specified. |
| 32 | Machine cut kota stone slab flooring with white boarder lining 20-25 mm thick as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab,as inin skirting, dados, risers to steps etc, laid over and including 10mm thick rendering in cement mortar 1:4 , cutting, rubbing, grinding and polishing to achieve mirror finish complete, all as specified. |
| 33 | Rounding to edges of stone slabs one edge,such as in steps, cooking platform, and other similar situations, complete all as specified. |
| 34 | Chequered cement concrete colouredtiles, homogenious texture glossy finished, chemically coated machine pressed 30 cm x 30cm x 25mm thick set, jointed and pointed in near cement slurry in floor with gray cement and pigment and including 20 mm thick cement screed in cement mortar 1:4 complete all as specified and directed. Note : Shade/Colour of tile shall be approved by the AGE(I). |
| 35 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 36 | Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement :4 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified. |
| 37 | Rendering cement plaster 15mm thick in cement mortar 1:6(1 cement :6 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement, complete all as specified. |
| 38 | Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement :4 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement,including taking down cement plaster, complete all as specified. |
| 39 | Rendering cement plaster 15mm thick in cement mortar 1:6(1 cement :6 coarse sand) in two layers (10mm thick first layer and 5mm thick second layer) on fair faces of brick wall or on concrete surfaces, surface finished even and smooth without using extra cement,including taking down cement plaster, complete all as specified. |
| 40 | Rendering cement plaster 5mm thick in cement mortar 1:3 on fair faces of brick or on concrete surfaces, as in ceiling , surface finished even and smooth without using extra cement, including taking down cement plaster, all as specified. |
| 41 | Supply only intergalwater proofing compound, complte all as specified. |
| 42 | Preperation of old plastered/painted surface of wall and applying wall care cement based putty 2mm thick , as per manufacturer\"s instructions, complete all as specified.Note : Where thickness of putty required is more than 2mm , the same shall be made good using POP and than putty shall be applied to obtain even and smooth surface and nothing extra shall be admisible on this account. |
| 43 | Preparation of new steel surfaces of any description, over 10cm in width or girth,not otherwise describedand applying two coats of synthetic enamel paint over a coat of red oxide primercomplete all as specified and directed. |
| 44 | Preparation ofnewplastered surfaces or un plastered, previously undecorated wall surfaces and applyingtwo coats of oil bound distemper over a coat of primer, complete all as specified and directed. |
| 45 | Preparation ofnewplastered surfaces or un plastered, previously undecorated ceiling surfaces and applyingthree coats of white wash, complete all as specified and directed. |
| 46 | Preparation ofnewplastered surfaces or un plastered, previously undecorated wall surfaces and applyingtwo coats of cement base paint over one coat of alkali resistant primer, complete all as specified and directed. |
| 47 | Wash basins, Vitreous China (Flat white type) size 550mmx400mm, with pedestal , crystal white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with PTMT coupling nuts at both ends, trap, grating and Union for discharge pipe, waste, chain and plug and porcelain stopper, waste pipe of polythylene of low or high density or PVC of 32mm dia including , 15mm bore cast copper alloy, with capstan heads, chromium plated, fancy type mixer, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed, completeall as specified. Make: Cat Part No. 1008 of Cera or equivalent in makes mentioned in Appx |
| 48 | Bib tap, cast copper alloy ,chromium plated, fancy type , screwed for iron pipe or for brass ferrule of 15 mm bore, fixed in repair, complete all as specified and directed. |
| 49 | Stop valve/Angle Valve cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unionsfor 15mm bore iron pipe or for unions and fixed in repairs complete, all as specified. |
| 50 | Brass CP wall mixer for mixing hot & cold water screwed down for iron pipe and fixed 15 mm bore, fixed in repair, complete all as specified and directed. |
| 51 | Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 52 | PVC connections 15 mm size with PTMT nutsof length 450mm fixed in repair complete all as specified and directed. |
| 53 | Brass chromium plated tubular towel rail 20 mm dia, \"D\" type, 60 cms long between flanges fixed in repairs with and including chromium plated brass brackets, brass screws complete all as specified |
| 54 | Brass chromium plated shower rose 125mm sizewith or without swivel joints, including fixing to steel pipe or union.fixed in repair complete all as specified. |
| 55 | 600x450 mm bevelled edge mirror of slected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plug with chromium plated brass screwed and cup washers. |
| 56 | Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, fixed in repair , complete all as specified. |
| 57 | PVC valve less, crystal white, syphonic action type flushing cistern 10 litre capacity, superior quality, plunger type, low level, with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long and 15 mm dia 600 mm long PVC connection with CP brass coupling nuts and PVC washers at both ends fixed, fixed in repair, all as specified. Make: Cat Part No. 2602 ofCera or equivalent in makes mentioned in Appx . |
| 58 | Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-1 using 20 mm graded crushed stone aggregate complete all as specified, incl making connections to trap and to flush pipe, etc, fixed in repair all as specified. Make: Cat Part No. 2071 of \"Cera\" or equivalent makes mentioned in Appx. |
| 59 | Sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, fixed in repair complete all as specified. |
| 60 | Steel plate rack of overall size 900mm x 775mm x 250 mm made of stainless steel having thickness1mm, fixed with screws , fixed in repair complete all as specified and directed. |
| 61 | G I tubingmedium gradeof 15 mm borewith all fittings and fixtures fixed to wall and ceiling or laid infloor /trenches including Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing . and making good, cutting not exc 10 cm girth, including .taking down old tubingcomplete all as specified and directed. |
| 62 | G I tubingmedium gradeof 20 mm borewith all fittings and fixtures fixed to wall and ceiling or laid infloor /trenches including taking down old tubingcomplete all as specified and directed. |
| 63 | 110mm dia PVC(SWR)pipe single socketed with rubber ringjoints, laid/fixed to tranches or in floor or walls, fixed in repair ,complete all as specified and directed. |
| 64 | 75mm dia PVC(SWR)pipe single socketed with rubber ringjoints, laid/fixed to trenches or in floor or walls, fixed in repair ,complete all as specified and directed. |
| 65 | 110mm dia PVC(SWR) bend, any radius complete all as specified and directed. |
| 66 | 75mm dia PVC(SWR) bend, any radius complete all as specified and directed. |
| 67 | 75mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified. |
| 68 | 20mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod &high density plastic ball screwed for iron pipe and fixed. (Minimum weight-210gms.),fixed in repair, complete all as specified. |
| 69 | Disconnecting existing tanks of capacity exceeding 250 Lires but but not exceeding 500 litres, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc, complete all as specified. |
| 70 | Rotational moulded polyethylene water storage tank 500 Ltrs capacity four layered (ISI Marked) cylinderical vertical with closed top, hoisted and fixed in position with ball brass valve, high pressure with PVC float valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line, including dismantling old tank any type,complete all as specified. |
| 71 | Deduct Credit Amount as per Schedule of credit as details given on Srl Page No 24 of tender doucments. |
