|
| 1 | Dismantling Brick tiles or terracing tiles, single layer on roofs, Complete all as specified and as directed. |
| 2 | Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof); Complete all as specified and as directed |
| 3 | Material and Labour for PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) as in padding concrete fair finish, roof kerbs or mud stops, rounded or chamfered on edges and like including weathering slight rounded and throating; Complete all as specified and as directed. |
| 4 | Supply and Fixing (minimum) 3mm thick APP film based poly meric membrance minimum weighing 3Kg per Sqm reinforced with polyester non wove fabric (weight not less than 150 gms/sqm) land on primed surface by forced application over entire roof area with over lapping 100mm to either sides and sealed in after cleaning down the roof by brooms including applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.6 Kg/Sqm including cleaning surfaces etc; Complete all as specified and as directed. |
| 5 | Material and Labour for 40mm thick brick tiles, laid on and including 15 mm thick cement mortar 1:6 and joints grouted and pointed flush in CM 1:3 mixed with 5% crude oil by weight of cement; Complete all as specified and as directed by Engineer-in-Charge. |
| 6 | All as per Srl item No 06 above but except bricks. Note: Old tiles obtained from dismantling shall be reused under this item. |
| 7 | Disconnecting existing tanks 1000ltr capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc complete all as specified and as directed. |
| 8 | Disconnecting existing tanks 500ltr capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc complete all as specified and as directed. |
| 9 | Demolition of cement concrete in ground floors and paving not exceeding 15 cm thickness ( below or above ground level) and disposing the rubbish to a distance exceeding 50 Mtr but not exceeding 100 Mtr away to low lying areas complete all as specified and directed. |
| 10 | Material and Labour for 50mm thick PCC 1:3:6 type C-2(using40mm graded stone aggregate as in plinth protection Finishing fair and even, complete all as specified and directed. |
| 11 | Material and Labour Chequered cement concrete tiles 30cm x 30cm x 25mm thick over and including 20mm thick bedding layer in cement mortar 1:6,set and jointed in neat cement slurry and pointed in grey cement and pigment to match the colour of tiles complete all as specified and directed. |
| 12 | Taking down cement plaster of any description on brick walls, etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed. |
| 13 | Material and labour for rendering 15 mm thick on brick work or concrete surfaces on walls in CM 1:6 finishing even and smooth without using extracementcomplete all as specified and directed. |
| 14 | Material and labour for rendering 15 mm thick on brick work or concrete surfaces on walls in CM 1:4 finishing even and smooth without using extracementcomplete all as specified and directed |
| 15 | Material and labour for rendering 10 mm thick on brick work or concrete surfaces on ceiling in CM 1:3finishing even and smooth without using extracement complete all as specified and directed. |
| 16 | Material and labour for PCC 1:1.5:3 type A-0 using 12.5 mm graded stone aggregate for repair of Chajja, Fascia, parapets etc using chicken wire mesh upto 8 m height including necessary formwork, scaffolding and applying two coats of cement base paint over coat of primer over cement plaster 1:4 complete all as specified and directed. |
| 17 | Material and labour for applying two coats of whitewash on ceiling including preparation of newly plastered surfaces complete all as specified and directed. |
| 18 | Material and labour for preparation of newly plastered surface of wall and Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification with two or more coats on new work complete all as specified and directed. |
| 19 | Material and labour for preparation of newly plastered surfaces and Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed. |
| 20 | Material and labour for complete removal of existing treatment from wall and applying putty of 1mm thickness to prepare the surface even and smooth and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed. |
| 21 | Material and labour for complete removal of existing treatment from wall and Finishing walls with Acrylic Smooth exterior paint of required shade : Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete all as specified and directed. |
| 22 | Hacking out old broken glass fromwooden/ steel window cleaning the surface and removing from the site, thenafter Supplying and fixing clear glass, 3mm thick ordinary quality, in any shape, not exceeding 0.50 sqm in each pane includingand glazing with oil putty/wooden beading as per site requiremnets complete all as specified and directed. |
| 23 | Supplying and fixing in Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staplescomplete all as specified and directed |
| 24 | Supplying and fixing in repair Helical door spring 300mm, ordinary rat tail rod pattern springs, including roller and roller plate fixed to iron chowkats with weilding complete all as specified and directed. |
| 25 | Supplying and fixing factory made 30 mm thick flush shutters solid core construction with block board core and plywood face panels, complete all as specified and directed. |
| 26 | Supplying and fixing IInd class hard wood Glazed and skeleton shutters 35mm thick divided into square, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (a) ; supplied and fitted to chowkats complete all as specified and directed |
| 27 | Material and labour for two coats of synthetic enamel painting on wooden surfaces of any description over 10 cm in width or girth not otherwise described above pink primer including preparation of previously untreated surfaces, complete all as specified and directed. |
| 28 | Material and labour for applying One coat of synthetic enamel paint on steel surfaces of any description over 10 cm in width or girth not otherwise described including preparation of old surfaces complete all as specified and directed |
| 29 | Material and labour for One coat of synthetic enamel painting on wooden surfaces of any description over 10 cm in width or girth not otherwise described including preparation of old surfaces complete all as specified and directed. |
| 30 | Supplying and fixing 300mm long Aluminium alloy, Anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed. |
| 31 | Supplying and fixing Aluminium, anodised, barrel tower bolts 150mm of extruded section and fixed, complete all as specified and directed. |
| 32 | Supplying and fixing 150mm longAluminium handles, cast type anodise, complete all as specified and directed. |
| 33 | Supplying and fixing stainless steel butt Hinges, 100mm size, medium weight, cold rolled mild steel complete all as specified and directed. |
| 34 | Materialand Labourfor Boxtypesteelwindowmade ofERW tube P- sectionof size 60 mmx25mm double rebated outer frame,comprises glazedskelton &gauzed shutterof ERW tube P-Section size 50mm x 20mmwith one/two Nos openable leaffor each shutter consisting of two Nos Sashbar of T-section 20 x 3 mmwelded to frame with one No verticle mullion of ERW box type T Section of size 60mm x 25mm and FI 2mm thick welded/screwed to frame for fixing of glass including fittings and fixture like as Handle, Tower Bolt, Stopper, Cleat, Pintle hinges, holdfast etc as given belowall as specified and directed.(a) Hold fast 150mm long of 12mm x 3mm MS flat- 4 Nos per Window.(b) Handle of Z section 20mm x 25mm, 100mm long- 01 No per leaf.(c) MS tower bolt 150mm long - 02 Nos/leaf.(d) Z Section stopper 20mm x 25mm, 100mm long - 01 No per leaf.(e) Cleat 55mm long of hollow square 15mmx12mm - 02 Nos per leaf.(f)MS pintol hinges size 75mmx12mm - 2 Nos per leaf complete all as specified and directed.Note :- Sheet glass, wire mesh and painting shallbe measured and paid sperately. |
| 35 | Material and Labour for Box type steel ventilator made of ERW tube P-section of size 60mmx25mmouterframe ( single rebated), comprisesglazed shutter, frame of ERW tube and FI 2mm thick welded/screwed to frame for fixing ofsheet glassincluding fixture and fittingslike as Stopper, Cleat, Pintal hinges, holdfast etc all as shown on drg No CEJZ/TD1019/08 sheet 1/3 to 3/3 dt 01 May 2008 complete all as specified.NOTE :-Sheet glass and painting shall be measured and paid Separately. |
| 36 | Supplying and fixing pressed steel frames 1.25mm thick for door size of frame 125 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges complete all as specified and directed. |
| 37 | Material and labour for PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) in bed blocks for hold fast & similar work etc complete all as specified and directed. |
| 38 | Taking down chowkhat with shuttering (without taking off shuttersfrom frame including grill & guard bars) sizeof shutter not exceeding 1.5 sqm each, complete all as specified and directed. |
| 39 | All as per Srl item No 38 above but size of opening exceeding 1.5 Sqmtr but not exceeding 4 Sqmtrcomplete all as specified and directed. |
| 40 | Taking down shutters of any description of size exc 1 sqm but n.exc 2 sqm, complete all as specified and directed. |
| 41 | Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 42 | Supplying and fixing non skid ceramic light coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles over and including 15mm thick screed bed in CM 1:4 & complete all as specified and directed. |
| 43 | Supplying and fixing glazed ceramic coloured tiles 450x300mmx6mm thick, etc. on vertical surfaces such as skirting , dados and risers to steps etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match over and including 10mm thick rendering plaster in CM 1:3 on brick surface complete all as specified and directed. |
| 44 | Supplying and fixing in repair vitreous ChinaSquatting pan \"Orrisa\" pattren size 580x440mm white with integral foot rest and PVC(SWR) \"P\" trap 110/110mm bore complete. Note :- Supply for Flushing cistern, flush pipe, seat cover shall be measured and paid separately under their respective items. |
| 45 | Supply only 10 Ltr capacity PVC valveless symphonic action type flushing cistern white low level with ball valve flote handle including bracket and flush pipe of polythylene of low or high density or PVC,32mm dia complete all as specified and directed. |
| 46 | Supplying and fixing in Repair vitreous China wash basinwhite,oval type including CP waste coupling 32mm bore,waste PVC pipe complete,CP brass Pillar Tap 15mm bore of fancy type complete all as specified and directed. |
| 47 | Supplying and fixing vitreous china urinal half stall type with CP spreader white incl CP waste coupling with grating and union fordischarge pipe, including providing and fixing plug, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement fixing with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed. |
| 48 | Supplying and fixing Vitrous china urinal partition white of size 310x770mm and fixed to wall terminating about 40cm above floor line complete al as specified and directed. |
| 49 | Supplying and fixing in repairs 15mm bore Concealed type stop cock cast copper alloy CP screweddown high pressure with crutch or butterfly handle complete. |
| 50 | Supplying and fixing in repairs 15mm bore type anglecock cast copper alloy CP screweddown high pressure with crutch or butterfly handle complete all as specified and directed. |
| 51 | Supplying and fixing in repair of brass cromium brass plated fancy type bib taps 15 mm bore long nose screwed down screwed for iron pipe or for brass complete all as specified and directed |
| 52 | Supplying and fixing in repairs PVC wastepipe32mm dia fixed to WHB/Urinals, complete all as specified and directed. |
| 53 | Supplying and fixing in repairs 100mm dia CP grating with or without hole type complete all specified and directed. |
| 54 | Supplying and fixing in repairs 8mm thick bevelled edge mirror of selected quality glass,mounted on CP stud including drilling cutting and fixed to wall complete all as specified and directed. |
| 55 | Supplying and fixing in repairs CP brass towel rail of 20mm dia and 600mm long complete all as specified and directed. |
| 56 | Supplying and fixing in repairs 125mm CP shower rose fancy type with CP arm complete all as specified and directed. |
| 57 | Supplying and fixing 15mm bore tubes (medium grade) galvanised with all fittings and fixed to walls and ceiling or laid in floors complete including taking down all as specified and directed. |
| 58 | Supplying and fixing 20mm bore tubes (medium grade) galvanised with all fittings and fixed to walls and ceiling or laid in floors complete including taking down all as specified and directed. |
| 59 | Supplying and fixing in repair PVC (SWR) pipe 75mm dia fixed in wall/floor, complete all as specified and directed. |
| 60 | PVC (SWR) pipes single110mm socketed, in any length with rubber ring joints, laid in trenches or in floors/wall, complete all as specified and directed. |
| 61 | Supplying and fixing in repair 75mm PVC (SWR) bends any radius, complete all as specified and directed. |
| 62 | Supplying and fixing in repair 110mm PVC (SWR) bends any radius, complete all as specified and directed. |
| 63 | Supplying and fixing in repair 75mm PVC floor trap, complete all as specified and directed. |
| 64 | PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed. |
| 65 | Supplying and fixing Solid PVC Door Frame of Size 50mm x 47mm made out of 5mm plain colour PVC Sheet reinforced with MS Square tube in opening as per specification and frawing, omplete all as specified and directed. |
| 66 | Supply and fixing 28 to 30 mm thick factory madesolid PVC moulded Door shutter with 2,3 or6 raised psnel design with 2mm thick moulded PVC Sheet on the front face and 2mm plain colour PVC Sheet on back face, fixing in frame at site as per specification and drawing, complete all as specified and directed. |
| 67 | Supply & Fixing rotational moulded polythene water storage tanks of 1000 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-1 including Ball valves high pressure PTMT with epoxy coated Aluminium rod & High density plastic ball screwed for iron pipe and fixed to GI pipe of 20mm bore, complete all as specified and directed. |
| 68 | Dismantling boarding , any description , fixed in any position with screws, complete all as specified and directed. |
| 69 | Material and Labour for 18/19mm thick Prelaminated HDHMR board, interior grade, with decorative choice lamination, fixed with screws as in shelves/Shutters, complete all as specified and directed. |
| 70 | Supply and Fixing steel cupboard shutter of MS 1.00 mm thick fitted in frame of 35x35x6mm thick including necessary fitting such as handle, lugs, locking arrangement and including shop coat of primer and n. exc 2.00 sqm area of cupboard complete all as specified and directed. |
