Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Laying and Jointing PVC Pipe. Heading |
| 2 | Installation of vertical cast in situ bored Pilesof 600 mm diametre using reinforced cement concrete Design Mix M30 Gradeusing 20 mm gauge hard broken stone jelly by settinng the bored cast in situ pile equipments with all accessories and tools at each locations based on the sequence of operations as directed by the departmental officer,boring for the piles from ground level in all soils to the required depth below cut off levelto carry a safe working load not less than specified, by Direct Mud Circulation Method ( using bentonite clay of required density) inclusive of pile accessories, temporary casing pipe,bentonite solution of 10% of concrete with required density,mobilisation,transferring,instalation of pile driving accessories from one location toanother,pile concreting inside of Trime method pipe fitting, including removal of mud andslurry away from the schemesite but excluding the cost of steel and fabricationreinforcement grillsbut including Bentonite solution machinery charges labour charges etc.,all complete, complying with relevent standard specification and as dircted by the departmental officers. ( pile shall be measured from the top of the shoe to the bottom of thepile cap.)Design Mix M30 Grade concreteshould be prepared with ordinary Portland Cement with water cement ratio not exceeding 0.45 including the use of Plasticizer of required Grade and Hard Granite Stone Jelly of 20mm size and downgraded as per requirement.a) conducting routine pile test for one and half times the safe load for every 1 in 100 piles, as per IS code and as directed by the Departmental Officers and b) Charge for chipping of pile wherever necessary to the required depth.C)Integrity Test should be conducted for all casted files and also carried out the work as per IS and necessary certificates needs to be provided.Concrete for all piling work should be of Design Mix M30 grade with minimum cement content of 400Kg per Cubic Metre.600mm dia pile |
| 3 | Test of single pile under routine load test, for a test load of 1350 KN (safe load (900x1.5) as per IS 2911 (part IV)-2013 inclusive of all charges for mobilization, extention or cutting of pile that may be necessary errecting loading platform in the manner acceptable and approved by departmental officer with labour and other incidental charges for loading and unloading test load and hire charges and all other incidental charges for conducting test including retaining the test load for 24hours at 100% capacity test certificate and caliberation charges for pressure gauge are to be produced to the Executive Engineer. Before commencing day of test. Caliberation of pressure gauge has to be done before applying the Ist load etc, complete in all respects as directed by departmental officers |
| 4 | Earth work excavation for foundation in all soils and sub-soilsto the required depth asmay be directed except in hard rock requiring blasting but inclusive of shoring, strutting, and bailing out water wherever necessary and refilling the sides of foundation with excavated earth in 150mm thick layers well watered rammed and consolidated and depositing the surplus earth in places shown clearing and levelling the site with an initial lead of 10 metres and lift as specified here under etc. complete in all respects complying with relevant standard specifications. (excluding Refilling) |
| 5 | 0 to 2m depth |
| 6 | 2 to 3m depth |
| 7 | 3 to 4m depth |
| 8 | Refilling in foundation and basement and other similar works with excavated earth in layers of 150mm thickness well watered rammed and consolidated etc all complete complying with relevant standard specifications and as directed by the Departmental officers. |
| 9 | Supplying and filling in foundation and basement with filling M sand in layers of 150mm thickness well watered rammed and consolidated complying with relevant standard specifications including cost offilling msand as directed by the Departmental officers. |
| 10 | Supplying and filling in foundation and basement with stone dust in layers of 150mm thickness well watered rammed and consolidated complying with relevant standard specifications including cost offilling sand and as directed by the Departmental officers. |
| 11 | Cement concrete 1:4:8 ( One of cement,four of M sandand eight of hard broken stone jelly) for foundation using 40 mm size broken stone jellyinclusive of shoring, strutting, baling out water wherever necessary ramming, curing etc., complete in all respect complying with relevant standard specifications and as directed by the departmental officers. |
| 12 | Flyash Brick Work in cement mortor 1:5 ( One of cement and five of Msand) using Fly ash bricks of size 230 x 110 x 70 mm having minimum average crushing strength of 50Kg/sqcm in foundation & basementincluding dewatering wherever necessary proper setting curing etc., complete in all respects complying with relevant standard specifications and as directed by the departmental officers. Foundation and Basement |
| 13 | A.A.C Block Work in cement mortor 1:6 (One of cement and four of sand) using AAC Block of size 600x 200 x 200 mm having minimum average crushing strength of 50Kg/sqcm for super structurein the following floors including labour for fixing the doors ,windows and ventilator frames in position fixing of hold fast ,scaffolding ,curing etc complete in all respects complying with relevant standard specifications and drawings and as directed by the departmental officers. |
| 14 | In Ground floor |
| 15 | In Firstfloor |
| 16 | In Secondfloor |
| 17 | In Thirdfloor |
| 18 | In Fourth Floor |
| 19 | In FifthFloor |
| 20 | In SixthFloor |
| 21 | AUTOCLAVED AERATED CONCRETE Block partition wall in cement mortor 1:4 (One of cement and four of M msand) 600x200x100mm thick for superstructurehaving minimum average crushing strength of 50Kg/sqcm. includinglabour for fixing the doors,windows and ventilator frames in position fixing of hold fasts scaffolding, curing etc. complete in all respects complying with relevant standard specifications and drawings and as directed by the departmental officers. |
| 22 | In Ground floor |
| 23 | In Firstfloor |
| 24 | In Secondfloor |
| 25 | In Thirdfloor |
| 26 | In Fourth Floor |
| 27 | In FifthFloor |
| 28 | Brick partition wall in cement mortor 1:4( One of cement and four of Msand) 70 mm thick for superstructure In Following Floors using class III ground moulded bricks of size 22x11x7cmhaving minimum average crushing strength of 50Kg/sqcm. includingcuring etc. complete in all respects complying with relevant standard specifications and drawings and as directed by the departmental officers. |
| 29 | In Ground floor |
| 30 | In Firstfloor |
| 31 | In Secondfloor |
| 32 | In Thirdfloor |
| 33 | In Fourth Floor |
| 34 | In FifthFloor |
| 35 | Providing 70mm thick stair case parapet wall using using Fly ash bricks of minimum size 230x110x70mmin cement mortar 1:4 and plastering both sides with cement mortar 1:4, 20mm thick and the hand rail portion only with red oxide plastering with cement mortar 1:4, 20mm thick providing skirting finishing smooth etc., all complete in all respects as directed by the departmental officers. |
| 36 | In Ground floor |
| 37 | In Firstfloor |
| 38 | In Secondfloor |
| 39 | In Thirdfloor |
| 40 | In Fourth Floor |
| 41 | In FifthFloor |
| 42 | Cement Concrete M30 Design Mix min Cement Content 400Kg/Cum for all reinforced cement concrete works namely Pile cap,Grade beam, Column and other similar works and other similar structures etc.with water cement ratio not exceeding 0.45 and minimum cement content of 380 Kg per Cubic Metre,.using ordinary Portland cement, river sand, 20mm and down size coarse aggregates, necessary approved admixtures as per requirement and using fly ash content not exceeding the 15 % in structural and non structural works excluding the cost of reinforcement grills, fabrication charges, shuttering and centering but including all leads and lifts, pumping using line pump or boom placer, scaffolding wherever necessary,laying,vibrating, finishing, curing etc all complete in all respects complying with relevant standard specification and as directed by the departmental officers. |
| 43 | In foundation and basement |
| 44 | In Ground floor |
| 45 | In Firstfloor |
| 46 | In Secondfloor |
| 47 | In Thirdfloor |
| 48 | In Fourth Floor |
| 49 | In FifthFloor |
| 50 | In Sixth Floor |
| 51 | Supply and erecting, centering for sides and sofits including supports and strutting up to 3.29 mt high for plane surfaces such as RCC slabs, rectangular beams, Tee (or) Ell beams, lintels, Bed Blocks, slabs, landing beam, canopy side slab or boxing or vertical slabs, rectangular or square or round columns etc. as detailed below with all cross bracings using MS sheets of size 90cm x 60cm and BG 10 stiffened with welded MS angles of size 25mm x 25mm x 3mm for boarding laid over silver oak or country wood joist of size 10cm x 6.5cm spaced at about 90cm centre to centre and supported by casurina props 10cm to 13cm dia spaced about 75cm center to centre or at nsuitable intervals etc. complete complying with standard apecification and as directed by the Departmental officers. |
| 52 | Providing form work for foundation, Plinth beam etc., complete in all respect complying with relevant standard specifications and as directed by the departmental officers. |
| 53 | Providing Form work for R.C.C. plain surfacessuch as Floor slabs, roof slabs, lintels beams etc complete in all respect complying with relevant standard specifications and as directed by the departmental officers. |
| 54 | Providing Form work for soffits of reinforced cement concrete worksfor small quantities complete in all respect complying with relevant standard specifications and as directed by the departmental officers. |
| 55 | Providing form work FOR VERTICAL WALL etc., complete in all respect complying with relevant standard specifications and as directed by the departmental officers. |
| 56 | Supplying of Door Frame of overall size 0.90 mX2.10m with required dimensions of size ~100mmX75mm, with groove of size - 30mmX20mm for resting the door shutter & chamfer finish at front using CRCA pressed steel box section 18 gauge or 1.25mm thick for door frames including providing holes and fixing wooden blocks for fixing fixtures and fittings and 4 nos of hold fast using the iron angle of 15cm length with split endsone coat of redoxide primer, Fabrication and supply of 35mm thick solid core flush door with teakply on one side and commericial ply on other side with teak wood liping alround with iron oxidised hinges, tower bolts 12\"2 nos with receiver, Aldrop 30cm and handle 1 no for door of Following size (Neruperichal HFA) Main door |
| 57 | Supplying of Door Frame of overall size 0.9 mX2.10m with required dimensions of size ~100mmX75mm, with groove of size - 30mmX20mm for resting the door shutter & chamfer finish at front using CRCA pressed steel box section 18 gauge or 1.25mm thick for door frames including providing holes and fixing wooden blocks for fixing fixtures and fittings and 4 nos of hold fast using the iron angle of 15cm length with split endsone coat of redoxide primer, Fabrication and supply of 35mm thick solid core flush door with teakply on one side and commericial ply on other side with teak wood liping alround with iron oxidised hinges, tower bolts 12\"2 nos with receiver, Aldrop 30cm and handle 1 no for door of Following size (Neruperichal HFA) |
| 58 | Supplying and fixing of solid pvc door shutter using19gauge 19mmM.S square tube for styles outer frames15mm for M.S square tubes for toplock top and bottom rails. the steel tubesshall be covered with5 mmthicksolid pvc sheets shutter for panelling shall rigidity fixed in positition including necessary furniture fittings.THe over all size of styles shall be 50mmX30mm. The over all stylesof top rails bottom railsshall be 75mmX 30mm. The over all size of framesshall be 50mmx 45mm with suitable rebate shutters.size 750X 1980mm |
| 59 | Supplying and fixing UPVC (Un-Plasticized Polyvinyl chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames.The window should be got approved from the Executive Engineer before use on worketc.. all, complete as per relevant standard specification and as directed by the departmental officers. |
| 60 | Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter.The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work. |
| 61 | Painting the flush door shutter of doors andwith one coat of first class enamel paint of approved quality and colour over one coat of primer including the cost of paint brushes and scaffolding etc., complete as directed by the departmental officers |
| 62 | Supply &fixing Mild steel grill of approved. The cost including of necessary screws, plugs, one coat of red oxide primier of approved quality, laboir charges for fixing etc.. all, complete as per relevant standard specification and as directed by the departmental officers. |
| 63 | Supplying and fixing in position of colour glazedwall tiles of any size6mm thickness laid in cement mortar 1:2( One of cement and two of msand) 10mm thick for wall facing / dadoing ,skirting over the plastered surfaces including cost of tiles fixing in position cutting the tiles to the required size wherever necessary pointing the joints with white/ colour cements neatly curing, finishing including cost of cement mortar etc complete and as directed by the departmental officers.Note:( The colour makeand quality shall be approved fromthe E.E before use ) Note: ( only one particulars size of ceramic wall tiles to be used for one building) |
| 64 | Supplying and fixing in position of Strain free nano polishVertified Floor tiles of 600 x 600 x 8 mm of approved special quality of 6mm thickness laid in cement mortar 1:3( One of cement and three of sand) 20mm thick for flooring including cost of tiles fixing in position cutting the tiles to the required size wherever necessary pointing the joints with white/ colour cements neatly curing, finishing including cost of cement mortar etc complete and as directed by the departmental officers.Note:( The colour and quality shall be approved fromthe E.E before useonly one particular size of ceramic wall tiles to be used for one building) |
| 65 | Supplying and fixing in position of colour Antiskid floortiles of any size of approved special quality of 6mm thickness laid in cement mortar 1:3( One of cement and three of sand) 20mm thick for flooring including cost of tiles fixing in position cutting the tiles to the required size wherever necessary pointing the joints with white/ colour cements neatly curing, finishing including cost of cement mortar etc complete and as directed by the departmental officers. Note:( The colour and quality shall be approved fromthe E.E before useonly one particular size of ceramic wall tiles to be used for one building) |
| 66 | Supplying and fixing in position offloor with eurocon tiles (Pre-polished Concrete Anti-Skid Tiles of 20mm thick) laid in cement mortar 1:3( One of cement and three of sand) 20mm thick for flooring including cost of tiles fixing in position cutting the tiles to the required size wherever necessary pointing the joints with white/ colour cements neatly curing, finishing including cost of cement mortar etc complete and as directed by the departmental officers. Note:( The colour and quality shall be approved fromthe E.E before useonly one particular size of ceramic wall tiles to be used for one building) |
| 67 | Finishing the top of flooring with cement concrete 1:3 Ellis pattern flooring 20mm thick in cement concrete 1:3(One of cement and Threeof stone jelly ) using 10mm and less hard broken stone chips (No msand to be used) including laying ,curing, finishing..etc complete complying with relevant standard specifications and as directed by departmental officers. |
| 68 | Suppplying and fixing of medium polished granite slab 20mm thick for kitchen herth slab of well polished on both sidessmoothly including fixing with CM 1:3 (one of cement three of sand)12mm thick including cutting to the required size laying fixing in position and jointing with black oxide and finishing neatly etc. as directed by the dept. officers. |
| 69 | Supplying and fixing of Cuddappa Cup Board planks of various sizes both side polished using 20 / 30mm thick cuddappa planks including fixing in position, finishing, curing etc., complete in all respects. |
| 70 | Supplying and fixing the Soap case corner slab of size 10\" radius for bathroom portion as directed by the departmental officers. |
| 71 | Supplying & Fixing of Stainless Steel Sink of Size 36\" x 18\" x7\"- along with 32mm dia B class G.Iwaste water pipe & 32mm dia C.P. waste coupling etc complete. |
| 72 | Weathering course with broken brick jelly lime concrete using 20mm gauge broken brick jelly in pure slaked lime ( no msand) over roof slab to the proportion of brick jelly to lime ( Fat lime) being 32: 12 1/2 by volume well beaten with wooden beaters, for giving the required slope and thickness complying with relevant standard specification and as directed by the departmental officers |
| 73 | Finishing the top of terrace floor with one course of solar reflective water proof, heat proof, cool proof tiles of size 300mm x 300mm x 8mm of approved quality laid in cement mortar 1:3 (One part of cement and three part of M msand) mixed with chemical mineral powder (60 kg for 1000 Sqft) (before laying tiles, the tiles should be dipped with salin based nano liquid) and top pointing with cement mortar 1:3 (One part of cement and three part of M msand) mixed with white cement, silicon powder and polymer additives (20Kg of 1000 Sqft) and joint pointed with a base concrete of PCC 1:2:4 using 6 to 10 mm metal for providing necessary gradient at top of roof etc., complete complying with standard specifications including cost of all materials, labour charges for lifting to open terrace, laying and finishing and other incidental charges etc., complete and as directed by the departmental officers. (The Brand and quality of tiles should be got approved from the Executive Engineer before using) |
| 74 | Plastering in C.M 1:3 (one of cement and three of msand)10mm thick for bottom of sunshade, ceilingin all floors, including scaffolding, curing ,finishing etc complete in all respects . |
| 75 | Plastering with cement mortar 1:5 ( One of cement and five of msand) 12mm thickfinished with neat cement including, providing band cornice scaffolding curing etc.,completecomplying with relevant standard specification and as directed by the departmental officer. |
| 76 | Plasteringwith cement mortar CM 1:4, 12mm thick mixed with water proofing compound @ 2 kg per 10 Sq including finishing smooth, proper setting, curingetc., Complete in all respects as directed by the departmental officers. |
| 77 | Plasteringwith cement mortar CM 1:3, 12mm thick mixed with water proofing compound @ 2 kg per 10 Sq including finishing smooth, proper setting, curingetc., Complete in all respects as directed by the departmental officers. |
| 78 | Providing and applying made wall putty of 2mm thickness over the plastered surface to prepare the surface even and smooth complete |
| 79 | Painting the new wallstwo coatswithbestapproved quality weather shieldexterior emulsion paint over one coat of primer including cost of brushes, emulsion paints scaffolding curing etc., complete in all respects complying with relevant standard specification and as directed by the departmental officers. ( The quality and shade of paint should be got approved by the Executive Engineer before use). |
| 80 | Painting the new walls with two coats of approved wall cement paint including cost of brushes, paints scaffolding curing etc., complete in all respects complying with relevant standard specification and as directed by the departmental officers. ( The quality and shade of paint should be got approved by the Executive Engineer before use). |
| 81 | White washing two coats of clean shell lime including cost of lime, gum, brushes, scaffolding etc., complete in all respects as directed by the departmental officers. |
| 82 | Painting New Iron work two coats with bestapproved Ist class synthetic ready mixed enamel paint of approved qualityetc., complete in all respects complying with relevant standard specification and as directed by the departmental officers. ( The quality and shade of paint should be got approved by the Executive Engineer before use). |
| 83 | Supplying, fabricating and placing in position of Mild steel Grills/Ribbed Tor Steels for reinforcement Fe550 HYSDfor all floors including cost of steel,binding wire, bending, tying etc, all complete complying with relevant standard specification and as directed by the departmental officers. |
| 84 | Providing pre-constructional Antitermite treatment including cost of chemicals labour as per standard specifications for preparing the area for treatment by spraying chemicals and other incidental charges etc.. complete. The rates should be for antitermite treatment from the plinth beam and brick masonry with super structure in contact with the back fill earth and at the junction of the walls.The top surface of filled earth for flooring and the soil along with the perimeter of the building by making holes with the crow bar and poured 5% termicide “Chloripyrifos” and sprayingthe same termicide solution on the wooden frames and treating the other periphery of buildings etc., complete in all respects as per IS 6313 (part II) / 1981 and as directed by the departmental officers. |
| 85 | Supply and fixing of Fabricated steel structural supports of ISA 40x40x6mm of weight 3.5 kg/m for water supply and waste pipes including msand blasting, with Twocoats ofenamel paint over one coat of primeretc. all complete complying with relevant standard specification andas directed by the Departmental officers. |
| 86 | Water supply , sanitory and Rainwater Arrangement |
| 87 | Supplying and fixing of 110mm dia PVC SWR pipe A Type for Rain water down fall pipe conforming to IS13592 with ISI mark and fittings conforming to IS 14735, with necessary C Igratings, shoes, bends,offset ,clamp, teak wood plug, GI Bolts and Nuts, etc., of approved quality and including fixing C.I. gratings at the junction of parapet and floor or roof slab , including finishing etc., complete complying with relevant standard specifications. and as directed by the departmental officers. |
| 88 | Supplying, laying, fixing and jointing the following PVC pipes as perUPVC of schedule 40 of wall thickness not less than the specified in IS 4985 suitable for plumbing by threading of wall thickness including the cost of suitable PVC/GI specials /GM specials like Elbow, Tee reducers, Plug , union, bend, coupler, nipple/ GM gate valve, check and wheel valve etc., wherever required above the ground level including the cost of teflon tape, special clamps, nails, etc., fixingon wall to the proper gradiant and alignment and redoing the chipped of masonry etc., as directed by the departmental officers. (above G.L) |
| 89 | 40 mm UPVC Pipes |
| 90 | 32 mm UPVC Pipes |
| 91 | 25 mm UPVC Pipes |
| 92 | 20 mm UPVC Pipes |
| 93 | Supplying, laying, fixing and jointing the following PVC pipes as per ASTM D – 1785 of schedule 40 of wall thickness not less than the specified in IS 4985 suitable for plumbing by threading of wall thickness including the cost of suitable PVC/GI specialslike Elbow, Tee reducers, Plug , union, bend, coupler, nipple etc., wherever required below ground level including the cost of Teflontape, special clamps, GI Bolts and Nuts, nails, etc., fixingon wall to the proper gradient and alignment and redoing the chipped masonry after the pipes are laidetc., complying with relevant standard specifications & as directed by the departmental officers. |
| 94 | 40 mm dia ASTM-D schedule 40threaded Pvc pipe with necessary PVC/GI specials etc.. all, complete as per relevant standard specification and as directed by the departmental officers. |
| 95 | Supplying and fixing of GM Gate valve following Dialabour for fixing etc, all complete and as directed by the departmental officers., (The quality and brand of fittings should be got approved fromthe Competent Authority before use) |
| 96 | 32mm dia Gate Valve (Heavy) |
| 97 | 40mm dia Gate Valve (Heavy) |
| 98 | Supplying and fixing ofSS Swan neck tap labour for fixing etc, all complete and as directed by the departmental officers., (The quality and brand of fittings should be got approved from the Competent Authorityr before use). |
| 99 | Supplying and fixing ofC.P Short body Bip cock with wall flange with Jaguarfittingsincluding cost of fittings , labour for fixing etc, complete complying with relevant standard specifications and as directed by the departmental officers. (The quality of fittings should be got approved fromthe Competent Authority before use) |
| 100 | Supplying and fixing ofC.P Long body Bip cock with wall flange with Jaguar fittingsincluding cost of fittings , labour for fixing etc, complete complying with relevant standard specifications and as directed by the departmental officers. (The quality of fittings should be got approved from the Competent Authority before use) |
| 101 | Supplying and fixing of C.P Concealed stop Cock with sliding flange of Jaguar fittings including cost of fittings , labour for fixing etc, complete complying with relevant standard specifications and as directed by the departmental officers. (The quality of fittings should be got approved from the Competent Authorityr before use). |
| 102 | Supplying and fixing of Oriya Type Indian Water Closet 580x440mm of approved make(to be got approved from EE before use) with P or S trap, including concrete filling the sunk portion with brick jelly lime concrete proportion of brick jelly to lime being 32:121/2 by volume (32 cft of 20mm gauge brick jelly and 12 1/2 cft of slaked lime) (No sand) and top 75mm thick brick jelly concrete in CC 1:8:16 (one of cement, eight of sand and sixteen of broken brick jelly) using 40mm size brick jelly including plastering the sides of sunk portion in Cm 1:3 (one of cement and three of sand) 12mm thick mixed with water proofing compound at 2Kg / m2 andtop left rough to receive the floor plastering but including antisyphonage connection including one coat of bitumen for the sides bottom and curingetc.,completecomplying with relevant standard specification and as directed by the departmental officer. |
| 103 | Ground Floor |
| 104 | Other than Ground Floor |
| 105 | Supplying and fixing the following dia PVC (SWR) pipe type B class conforming to IS 13592and relevant specials including packing the joints with rubber lubricant fixing them into walls with necessary GI Bolts and Nuts with special clamp made of MS angle/Flat including cutting, bending (excluding the cost of MS angle/flat) holding wherever necessary and making good of the dismantled portion with necessary connections to sanitary fittings etc.,completecomplying with relevant standard specification and as directed by the departmental officer |
| 106 | 110mm dia PVC SWR pipe including all required PVC specials etc., all complete and as directed by the departmental officers. |
| 107 | 75mm dia PVC SWR pipe including all required PVC specials etc., all complete and as directed by the departmental officers. |
| 108 | Supply and fixing of Cast Iron Nahani Trap with Stainless Steel Grating of Size 75mm x 50mm (Superior Variety) having minimum of water seal of 50mm confirm to relevant I.S. specifications with its latest amedments including resting on the bed of brick jelly concrete 1:5:10 (One of cement, five of sand and ten of 40 mm gauge brick jelly) etc.,completecomplying with relevant standard specification and as directed by the departmental officer. (The PVC Nahani Trap should be got approved from the competent authority before use) |
| 109 | Supplying and fixing the following dia UN PLASTICIZED NON - PRESSURE POLYVINYL CHLORIDE (PVC- U) Pipes for use in underground drainage and sewerage systems as per is 15328/2003 socket ends in dry conditions and tested with water including necessaryearth work exacavation for trenches and refilling the same well rammed and consolidated after the pipes are joined with PVC solution and tarred yarn laid to proper gradient to the alignment etc.,completecomplying with relevant standard specification and as directed by the departmental officer. ( SW pipes should be got approved by the Competent Authority before laying) |
| 110 | 110mm dia Pvc pipe |
| 111 | 150mm dia Pvc pipe |
| 112 | Supplying and fixing 150mm x 100mm size stone ware Gully trap with iron gratings over a bed of 150mm thick brick jelly concrete in CC 1:8:16 (one of cement, eight of msand and sixteen of broken brick jelly) using 40mm size brick jelly and brick masonry wall 115 mm thick using Second class chamber burnt ground mould bricks of size 9”x4-3/8”x2-3/4” (23x11.2x7cm) in cm 1:5 (One of cement and five of msand ) plastered with CM 1:3 (One of cement and three of msand) 12mm thick etc., complete complying with relevant standard specification and as directed by the departmental officers. |
| 113 | Constructionof Inspection chamber with brick jelly concrete 1:8:16 ( one of cement eight of sand and sixteen of hard broken jelly ) using 40mm gauge broken brickjelly 15cm thick for foundation and 23cm thick brick masonry in C.M. 1:5 ( One of cement and five of sand) using II nd class ground mouldedChamber burnt bricks of size 9”x4-3/8”x2-3/4” plastering with cement mortar 1:3 ( One ofcement and three of sand) 12mm thick on both sides top and bottom including earth work excavation,supply and fixing of SFRCcover slab of size 60cmX60cm including benching charnelling fixing cover slab in position curing finishing etc., complete in all respects.complying with relevant standard specification and as directed by the departmental officers. |
| 114 | Inspection Chamber of Size 60x60x45 cm |
| 115 | Inspection Chamber of Size 60x60x60 cm |
| 116 | Inspection Chamber of Size 60x60x90 cm |
| 117 | Inspection Chamber of Size 90x90x120 cm |
| 118 | Supplying and Fixing of PVC moulded CI Steps for fixing proper position and deistance including labourcharges,etc., complete in all respects complying with relevant standard specification and as directed by the departmental officers. |
| 119 | Electrical Arrangements |
| 120 | Wiring with2 x 1.5 sqmm copper PVC insulated unsheathed single core Multi StrandFlame Retardant Low Smoke 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990andwith continuous earth by means of 1.5 sqmm copper insulated unsheathed single core Multi StrandFlame Retardant Low Smoke 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 infully concealed PVC rigid conduit pipe heavy duty with ISI with suitable size MS box of 16 gauge thick concealed for light point with ceiling rose controlled by 6 amps flush type modular switch with \"Light\" marking including circuit mains cost of all materials, specials etc., all complete complying with relevant standard specifications and as directed by the departmental officers. |
| 121 | Light point with ceiling Rose |
| 122 | Light point with Backlite Battern Holder |
| 123 | Wiring with2 x 1.5 sqmm copper PVC insulated unsheathed single core Multi StrandFlame Retardant Low Smoke 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990andwith continuous earth by means of 1.5 sqmm copper insulated unsheathed single core Multi StrandFlame Retardant Low Smoke 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 infully concealed PVC rigid conduit pipe heavy duty with ISI with suitable size MS box of 16 gauge thick concealed and for Fan Point controlled by 6 ampsflush type modular switch with \"Fan\" markingincluding circuit mains cost of all materials, specials etc., all complete complying with relevant standard specifications and as directed by the departmental officers. |
| 124 | a) Ceiling Fan Point / Exhaust Fan point |
| 125 | Supply and fixing of concealed type fiber box with MS fan hook of 100mm dia ,75mm depth and 3mm thick etc., all complete complying with relevant standard specifications & as directed by the departmental officers.. |
| 126 | Wiring with 2 x 1.5 sqmm copper P.V.C. insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990andwith continuous earth by means of 1.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS Box of 16g thick concealed for Staircase Light Point controlled by6 amps flush type modular two wayswitch with \"Light\" marking including circuit mains, cost of all materials, specials, etc.,completecomplying with relevant standard specification and as directed by the departmental officer. |
| 127 | Wiring with 2 x 1.5 sqmm copper P.V.C. insulated unsheathed single core Multi StrandFlame Retardant Low Smoke 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 and with continuous earth by means of 1.5 sqmm copper PVC insulated unsheathed single core Multi StrandFlame Retardant Low Smoke 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS boxof 16 gaugethick concealed and covered with 3mm thick laminated hylem sheetfor 6 amps 5 pin plug socket pointat Switch Board Itself including circuitmains, cost of all materials, specials, etc., all complete complying with relevant standard specifications & as directed by the departmental officers |
| 128 | Wiring with 2 x 1.5 sqmm copper P.V.C. insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 and with continuous earth by means of 1.5 sqmm copper PVC insulated unsheathed single core Multi Strand Fire Retardant 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990in fully concealed PVC rigid conduit pipe heavy duty with ISI mark with suitable size MS boxof 16 gaugethick concealed and covered with 3mm thick laminated hylem sheetfor 6 amps 5 pin plug socket pointat convenient place including circuitmains, cost of all materials, specials, etc., all complete complying with relevant standard specifications & as directed by the departmental officers.. |
| 129 | Supplying and fixing of water tight Bulk head fittings with One number of 9 Watts LED BULB including necessary connections, cost of materials etc., all complete complying with relevant standard specifications & as directed by the departmental officers.( The Brand/Quality of fittings and LED Lamphas to be got approved by the EE before fixing) . |
| 130 | Supplying and fixing of SINGLE PHASE DISTRIBUTION BOARD WITH MCBs 4 way vertical SPMCB metal sheet door cover with IP42 protection distribution boards flush type / surface type fitted with bus bars and neutral links with single phase MCB outgoings and separate 2 way provision for accommodating One No. 2 pole incoming MCB / Isolator and another separate 2 way provision for accommodating One No. 2 pole ELCB / RCD with label holder and provisions for taking up cable for size not less than 35 sq.mm includind labour charges etc., complete in all resspcets as directed by the departemental officers. (4 ways single phase DBNo. of ways incomer MCB / Isolator - 2No. of ways incomer ELCB / RCD - 2No. of outgoings ways - 2) |
| 131 | Run of main with 2 wires of 2.5 Sqmm Copper PVC insulated unsheathed single core Multi Strand Flame Retardant Low Smoke 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 andwith continuous earth by means of 1.5 sqmm copper PVC insulated unsheathed single core Multi Strand Flame Retardant Low Smoke1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990in fully concealed 19/20mm dia rigid PVC conduit pipe with ISI mark etc. including cost of all materials, specials etc. all complete and as directed by the departmental officers. |
| 132 | Run of main with 4 wires of 6 Sqmm Copper PVC insulated unsheathed single core Multi Strand Flame Retardant Low Smoke 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 andwith continuous earth by means of 2.5 sqmm copper PVC insulated unsheathed single core Multi Strand Flame Retardant Low Smoke 1.1 KV grade copper cable with ISI Mark conforming to IS:694/1990 in fully concealed 32mm dia rigid PVC conduit pipe with ISI mark etc., including cost of all materials, specials etc. all complete and as directed by the departmental officers. |
| 133 | Supplying and laying of 25x3mm GI Stripon walls/below G.L. with necessary \"U\" nails earth work excavation and refilling etc., including cost of all materials etc.all complete in all respects complying with relevant standard specification and as directed by the departmental officer. |
| 134 | Supplying and laying of 8 SWG , Copperwire on walls/below G.L. with necessary \"U\" nails earth work excavation and refilling etc., including cost of all materials etc.all complete in all respects complying with relevant standard specification and as directed by the departmental officer. |
| 135 | Providing earthing station using pipe electrode as per IS 3043 using 40mm dia B Glass G.I pipe 2.5 meters. 20mm dia B class G.I. pipe 1 metre 40 x 20mm G.I. Reducer 1 no.1 set of funel G.I. nuts, bolts, washers and checknuts, 1 no.of SFRC heavy duty cover (60 x 60cm ) 40Kg charcoal, 2nos.of C.I.bend 15mm dia 4 Nos.of 15mm dia G.I. coupling and 10Kg salt including necessary earth work excavation (i.e. by augering 30cm dia to a depth of 3.5 metres.and laying the salt and charcoal in layer by layer around G.I.pipe brick work in Cement mortar and plastering etc . Including cost of all materials and labour in accordance with IS 3043. etc.all complete in all respects complying with relevant standard specification and as directed by the departmental officer. |
| 136 | Supplying and fixing of Single type Street light LED Fitting20 mm dia GI pipe \"B\" class with clamps, boltsetc.,complete with ISI mark, complying with relevant standard specifications & as directed by the departmental officers. |
| 137 | Supplyinglaying and connecting3 1/2 core 25 sq.mm. PVC Armoured UG Cablewith ISI mark of reputed brandincluding fixing in walls with necessary MS clamps, brass screws including cost of all materials redoing the dismantled portion, etc., all complete complying with relevant standard specification andas directed by the Departmental Officers. (The quality and brand of UG cable should be got approved by Competent Authority before use) |
| 138 | Lift |
| 139 | Bedcum passenger lift SS 304grade with 1.5 meter per sec speed with ARD 10 person passenger liftwith machine room Nos of floors - (G+5 floors) - Position of machinery - Directly above the lift well - Gearless. Land entrance protection - centre opening sliding door 900mm width ss with (1.5mm) Hairline Flinsh. type of control system - micro processor Build simplex, Selective , collective control with or without attender. car fittings - LED light and regular (circulation) - fan1.Battery operated Emergency Light and alaram bell 2.Call register signal and VF door operator 3.Landing push button landingdoor frames4.Automatic resuce device 5.Vandal proof S.S button with S.S cover 6.Braille button 7.Full car operating panel 8.Dot matrix led D& P indicators in car & landing orange colour 9.Floor annunciato with music 10.firemans awitch 11.False ceiling in car 12.Fire rating of landing door 2Hrs 13.Infra red screen 14.Overload warning indicator 15.Scaffloding 16.3Way intercom /press and speak phone 17.Free service for one year 18.Pit ladder 19 SS handrail 20.Lift license 21.Minor builders worketc.. all, complete as per relevant standard specification and as directed by the departmental officers.Note: Rate Inclusive of Comprehensive sevicing and maintenance of lifts for further period of 2 years beyond free warranty period of one year from the date of commissioning of lifts will be paid at the rate of 5% of capital cost of liftwhile handing over of lift to the department officers/ allottees the lisense and insurance should live condition |
| 140 | RAINWATER HARVESTING |
| 141 | Providing Rain water Harvesting pit by earth work of 90cm dia and 60 cm depth and filling with stone jelly 40mm size including earth work excavation filling work with the stone jelly and covering with precast RCC 1:2:4 slabs, precast well ring RCC 1:2:4 including cost of steel and fabrication of reinforcement and grills precasting moulding, curing finishing and placed in position andaugaring 300mm dia bore pit to a depth of 4.40m and filling the entire depth of bore pit using river M sand15% 20mm H.B Stone jelly 50% and 40mm H.B Stone jelly 35% including Supplying & fixing1No. Gully trap with 110 mm dia PVC pipe for jointing including the cost of materials and labour charges etc.. complete in all respect as directed by departmental officers. |
| 142 | PAVER BLOCK |
| 143 | Supplying and laying of concrete interlocking blocks of 63 mm thickness using rubber mould,approved make with grey colour including cost of conveyance of interlocking blocks and filling sand and spreading of sand to a thickness of 15 cm for cussion below the interlocking blocks and consolidating, vibrating labour charges for laying to proper level slope etc. as directed by the dept. officers (Design and colour of interlocking blocks should be got approved by EE before using) |
| 144 | AVENUE TREES |
| 145 | Supply and planting of avenue trees including earth work excavation for pit of size 60x60x60cm filled with manure for 20cm depth and filling with river sand and red earth mixintheratioof1:1 for 40cm depth in the same pit and planting the avenue trees of approved varities to a height of 200cm from thegroundleveland maintaining them for the period of 6 month including watering, periodical manuring and replacing the avenue trees if dead etc., all complete and as directed by the departmental officers. (Tree sappling shall be got approved from competent authority before planting) |
| 146 | Supplying and fixing of Square shape chicken mesh TREE GUARD using 8cm dia casurina vertical post and middle tie using country wood reeper of size 50x25mm and 25 gauge chicken mesh including labour charges for fixing the Square tree guard and as directed by the departmental officers |
| 147 | NUMBERING |
| 148 | Supply and Fixing ofSignage /Numbering Plate with 304 grade 18 SWG thickness stainless steel etching name board of size 10\" for Flat which can be mounted in wall withPolished Surface Finish etc complete complying with standard specification and as directed by the departmental officers |
| 149 | EXTERNAL WATER SUPPLY |
| 150 | Supply, delivery, erection and commissioning of 3 H.P 3 phase centrifugal submersible pumpset of best approved superior quality with ISI mark as per IS 9079 /1989 with out panel board suitable for 400/440V, 2880 RPM with 50 cycles AC power supply with Gun metal/bronze impeller and shaft having stainless steel or alloy steel having high resistance to wear and tear and corrossion suitable for the following duty condition etc., all complete as directed by the departmental officers. |
| 151 | Labour charges for the erection of submersible pumpset in borewell/openwell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, Voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pumpset and trail run for 10 days. |
| 152 | Supply and laying of PVC insulated flat 3 core type 4 sqmm copper cable confirming IS694/90 with ISI mark for three phase submersible pumpset including hire charges for laying cable below ground level including earthwork , refilling , cost of materials etc complete complying with standard specification and as directed by the departmental officers. |
| 153 | Supply and fixing of Star-Delta starter with two level gaurd and auto start confirming to IS 13947, IEC60947-1 and as amended thereafter with suitable KW rating for operation in AC/ Three Phase/50HZ (+/- 5%) and 415V (+/- 10%) including 3 pole magnetic contactor with under voltage release - 3 nos., CT operated Ammeter (65 mm dia) with suppressed scale, Voltmeter (65mm dia), Voltmeter selector switch, Miniature circuit breaker, Thermal Overload relay, Air Break contactors suitable for next Standard higher KW rating, Single phasing preventor, dry running preventor and On/Off Push button switches, wiring with 1 sq.mm/4 sq. mm copper pvc insulated cable, powder coated vermin proof box, including the capacitor |
| 154 | Genset |
| 155 | Supply of 40 KVA KOEL GREEN GENERATORS WITH AUTO MAIN FAILURE (AMF) PANEL incorporating Kirloskar Water Cooled Diesel Engine, Kirloskar Green alternator, 3 phase, 415 Volts, 0.8 PF, Standard control panal CPCB II approved Acoustic Enclosure, Battery & Diesel Tank ( Generator Used for Producing electricity)Techincal specification enclosed including Liasioning with electrical inspector for preparation of drawing such as schmatic layout , earthing layout etc., submission of drawing to electrical inspector (chennai south) and getting drawing approval. Preparation of work completion report and arranging EI inspection . Preparation of defect report after inspection and obtaining safety certificate. etc complete complying with standard specification and as directed by the departmental officers. |
| 156 | Providing Exhaust Pipe With Silencer including charges for scaffolding, labour charges, MS channel, fastner & bolts etc complete complying with standard specification and as directed by the departmental officers. |
| 157 | Supplyinglaying and connecting 31/2 C x 50 sq.mm aluminum armoured UG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt . Layer of msand and covering the cable completely with bricks and msand and refilling the earth to make goodetc.. all complete complying with relevant standard specifications & as directed by the departmental officers. (The quality and brand of UG cable should be got approved by Executive Engineer before use). |
| 158 | Supplyinglaying and connecting 31/2 C x 95 sq.mm aluminum armoured UG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt . Layer of msand and covering the cable completely with bricks and msand and refilling the earth to make goodetc.. all complete complying with relevant standard specifications & as directed by the departmental officers. (The quality and brand of UG cable should be got approved by Executive Engineer before use). |
| 159 | Supply and fixing of brass cable gland for XLPE armoured LTUG cable for following sizes with earth connection. |
| 160 | 3 1/2 x 50 sqmm aluminium cable |
| 161 | 3 1/2 x 120 sqmm aluminium cable |
| 162 | Supply and providing cable end termination of following sizes of XLPE armoured LTUG Aluminium cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete. |
| 163 | 3 1/2 x 50 sqmm aluminium cable |
| 164 | 3 1/2 x 120 sqmm aluminium cable |
| 165 | UG Sump |
| 166 | Supplying and Fixing of SFRC manhole cover for size 600x600mm heavy duty including cost of labour charge,etc., complete in all respects complying with relevant standard specification and as directed by the departmental officers. |
| 167 | Sub Total |
| 168 | GST @18% |
| 169 | 3 1/2 x 50 sqmm aluminium cable |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2025 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
