|
| 1 | Civil Works (Part-A) |
| 2 | Earth work excavation in foundation in hard soil with 50 mtr initial lead 1.5 m initial lift including rough dressing and breaking clodsto 2 cm to 7 cm and laying in layers not exceeding 0.3 m in depth as per direction of Engineer-in-charge. (Excavation by manually) |
| 3 | Earth work excavation in foundation in hard soil with 50 mtr initial lead 1.5 m initial lift including rough dressing and breaking clodsto 2 cm to 7 cm and laying in layers not exceeding 0.3 m in depth as per direction of Engineer-in-charge.(Excavation by mechanical means with excavator of bucket size 0.6m) |
| 4 | Filling foundationand plinth with sand watered and rammed as per direction of Engineer-in-charge. |
| 5 | Cement concrete (1:4:8) with 4 cm size h.g metal as per direction of engineer-in-charge. |
| 6 | Cement concrete (1:2:4) with 12 cm size h.g Chips as per direction of engineer-in-charge. |
| 7 | Rigid and smooth centering and shuttering for RCC work including false work and dismentalling them after casting including cost of materials complete. Foundation plinth bend |
| 8 | Rigid and smooth centering and shuttering for RCC work including false work and dismentalling them after casting including cost of materials complete. Column |
| 9 | Rigid and smooth centering and shuttering for RCC work including false work and dismentalling them after casting including cost of materials complete. Lintel |
| 10 | Rigid and smooth centering and shuttering for RCC work including false work and dismentalling them after casting including cost of materials complete. Roof Slab & Chajja |
| 11 | RCC (1:2:4) with 12 mm size HG chips as per direction of engineer-in-charge. |
| 12 | Supplying, fitting and placing oncoatedHYSD (TISCON) bar reinforcement complete as per drawing and technical specification including cutting, binding, bending and cost of binding wire. |
| 13 | Cost of MS Grill for door, Choukath |
| 14 | Cost of Iron Shutter, windows |
| 15 | Fly Ash Brick (25cmx12cm x8 cm) having crushing strength not less than 35kg/cm with dimensional tolerance ± 5% in cement mortar (1:6) in foundation and plinth. |
| 16 | Fly Ash Brick (25cmx12cm x8 cm) having crushing strength not less than 35kg/cm with dimensional tolerance ± 5% in cement mortar (1:6) in super structure. |
| 17 | 2.5 cm thick A.S flooring with C.C. (1:2:4) including punning as per direction of Engineer-in-charge. |
| 18 | 12mm thick cement plaster (1:6 ) over brick masonary as per direction of Engineer-in-charge. |
| 19 | Filling F & P with excavated materials, moorum including watering and ramming as directed by the engineer-in-charge |
| 20 | Filling F & P with excavated materials, moorum including watering and ramming as directed by the engineer-in-charge (for Pipe Laying) |
| 21 | White washing three coats with shell time as per direction of Engineer-in-charge. |
| 22 | Cement punning over cement plaster as per direction of Engineer-in-charge. |
| 23 | Painting 2 coats with approved paint on new work as per direction of Engineer-in-charge. |
| 24 | Distempering two coats to walls with distemper of approved shade on new work to give an even shade after 1 coat of white washing as per direction of Engineer-in-charge. |
| 25 | 20mm thick cement plaster 1:4 for grading plaster as per direction of Engineer-in-charge. |
| 26 | Supply, fitting and fixing of skylight as per direction of Engineer-in-charge. |
| 27 | Writing charges of required data on the wall of pump chamber as per direction of Engineer-in-charge. |
| 28 | Cost of supplying transportation and fixing in proper place and position including required size full threaded TVS nut bolt with CC (1:2:4) as per site condition |
| 29 | Cost of outlet |
| 30 | Cost, Supplying of ISI marked High Density Polythelene (HDPE) Pipes for water supply as per IS 4984/2016 in the following Nominal diameter, Grades of materials, Pressure rating as per direction of the Engineer-in-Charge. 200 mm HDPE PE-80 PN 4 |
| 31 | Cost, Supplying of ISI marked High Density Polythelene (HDPE) Pipes for water supply as per IS 4984/2016 in the following Nominal diameter, Grades of materials, Pressure rating as per direction of the Engineer-in-Charge. 160 mm HDPE PE-80 PN 4 |
| 32 | 10 HP/7.50 KW Energy efficiency Monoblock pump set of total head 18 mtrs having discharge 1700 LPM withsquirrel cage induction motor fitted with bronze impeller TB-2 of IS 318/1981, companion flanges & Class \"F\"insulation suitable for operation 415 volt +6%-15% 3 phase, 50Hz AC poweer supply suction/deliveery= 100mmx100mm with BEE 3 Star rated energy efficiency Pump & as per IS-9079/2002 with overall efficiency 62 to 65% of reputed brand having wide dealership net work for easy availability of spares confirming to IS specification (a) Casing: FC 200 as per IS 210/1978 (b) Impeller: Bronze grade LTB-2 of IS 318/1981 including all cost, conveyance, cess etc complete. |
| 33 | Control Pannel with Automatic Star delta Starter, sheet steel enclosure suitable for operation of Squirrel cage induction motor up to 10 HP with 16 Amp (AC -3) duty contractor at 415 Volt+6%-15%, 3 phase, 50 Hz AC supply with over load relay range 8.9 to 13.5 Amp & no volt coil with electronic timer suitable for operation at voltage range of 300 to 440 V. The Starter should provide dependable protection against over load and single phasing fitted with Volt Meter, Ameter, MCB in complete shape including Indicator Lamp reputed brand of ISI specification including all cost, conveyance, cess etc complete. |
| 34 | Empty Outdoor Irrigation Pannel Board size (0.45mtx0.25mtx1.20m of 18 SWG Cold Rolled M.S Sheet with 4 legs of 300 size with one coat of Red Oxide Primer and two coats of Smoke grey /Navy bluetwo coats of powder coated paint of approved quality on both side (Inside & Outside) suitable to mount 3Phase Starter, Main Switch and Capacitor inside the Panel Board vertically over 18 SWG M.S.Sheet and the danger board fixed on the top of the Panel Doorreputed brand of ISI specification including all cost, conveyance, cess etc complete. |
| 35 | 63 AMP Triple Pole Main switch confirming to IS No.4064(Part I & II) with ISI marking of reputed company having utilisation capacity cagegory AC- 22 reputed brand of ISI specification including all cost, conveyance, cess etc complete. |
| 36 | Motor hood size (0.45mx0.45mx0.60m) made with 18 SWG (cold rolled M.S.Sheet with one coat of red axide primer and two coats of powder coated paint of approved quality on both side (inside & outside) suitable to cover centrifugal monoblock Pump Set from 10 HP to 15 HP and having provision for attachement with the groves on rear side of the pannel board of approved brand including all cost, conveyance, cess etc complete as per the direction of the Engineer-In-Charge |
| 37 | Motor base plate made with M.S angle with one coat of red axide primer and two coats of powder coated paint suitable to cover centrifugal monoblock Pump Set from 10 HP to 15 HP and having provision for hole for fixing nut & bolt of approved brand including all cost, conveyance, cess etc complete as per the direction of the Engineer-In-Charge. |
| 38 | 6 KVAR Power ShuntCapacitor with ISI mark of of reputed approved brand ofISI marked including all cost, conveyance, cess etc complete. |
| 39 | 3x16 sqmm PVC insulated (HD) tropoder armoured Electric Cable with alluminum conductor for use in 3 phase power system of working voltage upto & including 1100 volts at 50Hz confirming to IS 7098 (Pt-II) of approved brand ofISI marked including all cost, conveyance, cess etc complete. |
| 40 | 4.0 mm2 PVC Single Core CopperWire ISI mark of of reputed approved brand ofISI marked including all cost, conveyance, cess etc complete. |
| 41 | 100mm dia nominal bore G.I.pipe having wall thickness 4.5mm electrical resistance welded of medium class confirming to IS- 1239(part-1/2004) with latest ammendments, screwed at both ends as per IS-554 with socketed at one end and the other end protected with plastic threaded protector including its transportation and unloading at L.I.P. site. The socket confirming to ISI 1239(part II/1992) with latest ammendments in random length of 4 to 7 mtr.Each pipe should bear IS certification and manufacturers name/trade mark. (As per S/R 2022) |
| 42 | 100mm dia G.I.Bend (Medium Duty) conforming to IS No-1239 (part II/1992) with ISI mark of reputed brand including all cost, conveyance, cess etc complete. |
| 43 | 100mm dia C.I. Screw boss Foot Valve of swing type friction less with single disc conforming to IS-4038/1979 of reputed brand with ISI mark of reputed company having wide dealership network including all cost, conveyance, cess etc complete. (Kirloskar make) |
| 44 | 100mm dia G.I.Flange (Medium Duty) conforming to IS No-6392/1971 with ISI mark of reputed brand including all cost, conveyance, cess etc complete. |
| 45 | 100mm dia C.I.Sluice Valve Flanged type PN-1.0 as per(IS-14846-2000 Standard) with ISI mark of reputed brand including all cost, conveyance, cess etc complete. (As per S/R 2022) |
| 46 | 100mm dia C.I.Double Flanged Non Return Valve swing type PN-1.0 (IS-5312 (Part-I-2004) with bypass arrangement with ISI mark of reputed brand including all cost, conveyance, cess etc complete (As per S/R 2022) (Kirloskar make) |
| 47 | Cost, supplying of 50mm dia Kirloskar make C.I double Air Release Valve PN 1.6 with saddle and Raiser pipe conforming to IS 14845 (SI) with ISI mark including all cost, conveyance, cess etc complete. |
| 48 | Cost of 200x200x160mm dia HDPE Tee. |
| 49 | Cost of 160mm dia HDPE End Cap. |
| 50 | Cost of 200mm dia HDPE End Cap. |
| 51 | Cost of 100x100x25mm dia G.I. Tee, Bend, Valve for Priming set. |
| 52 | 200x100mm M.S Reducer |
| 53 | Labour charge for laying, fitting,T&P for jointing of HDPE pipes of specified materials grade and pressure rating by butt fusion welding method as per specification and lying in tranches, testing including all cost etc complete as per direction of the Engineer-in-Charge. 200 mm HDPE PE-80 PN 4 |
| 54 | Labour charge for laying, fitting,T&P for jointing of HDPE pipes of specified materials grade and pressure rating by butt fusion welding method as per specification and lying in tranches, testing including all cost etc complete as per direction of the Engineer-in-Charge. 160 mm HDPE PE-80 PN 4 |
| 55 | Labour charges for delivery and fitting, fixing of suction including fitting of priming Tee, Tee set, NR valve, Sluice valve and Air release valve etc minor welding transportation of materials to site etc. including nut, bolt rubber insallation etc complete. |
| 56 | 160x160x160mm HDPE equal Tee. |
| 57 | 160x160x110mm G.I. Raisar Tee with assoceries |
| 58 | Cost of Butter Fly Valve |
| 59 | Electrical Works (Part-B) |
| 60 | Construction of 3 Phase L.T line as per REC standard confirming to RE rule 1956 with 300Kg 9 Mtr long PSC pole support in 33 mtr span length with 4x35mm² + 1x35 + 1x16 mm ² LT, XLPE AB cable with coil earthing device, LT dead end clam, Suspension clamp with G I hook, stay accessories such as wire insulator , clamp etc. nut bolts, alongwith concreting copping & padding of polesand stayset as per direction of Engineer in Charge as per TPCOCL specification etc. including cost of all materials, labour , transportation complete with liaising for testing inspection & commissioning as per specification of TPCODL etc complete. |
| 61 | Electrical Earthing with 40mtr dia medium duty GI earthing pipe each 3 m longwith installation including cost of all materials like GI flange chorcoat, salf etc. as required as per I.E Rule |
| 62 | Other Electrical materials such as pvc tape.7/20pvc copper wire 3/20 pvc copper wire G.I flxible condite pipe no 6 GI wire copper cable socket GI socket and petty materials required for electrical installation. All materials should be as per IS including fitting charges. |
| 63 | Cost of document which includes pre and post photograph (2 copies) power supply agreement of pani panchayat office bearers with CESU authorities, handing over documents (agreement) of pani panchayat with OLIC authority recording of latitude and longitude etc complete. |
