Tender For Renovation Of Room 101 - Tripleisotope Analyser Facility; 1 Renovation of Room 101 – Triple Isotope Analyser Facility in NCESS 2 13.80, Providing and applying white cement-based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete 3 13.83.2, Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. 13.83.2 Two coats 4 13.85.3, Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. 13.85.3 With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre 5 13.112.1, Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shadeOld work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface 6 13.52.1, Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturers specifications including appropriate priming coat, preparation of surface, etc. complete. 13.52.1 On steel work 7 LMR, Providing and applying two coats ofelastomeric liquid water proofing membrane with resilient acrylic polymers (such as DrFixit-Rain-coat Star or likewise materials of other brand) on wall surfaces without water dilution (ensuring a coverage rate of 4.2-4.5 m2/ Lit/two coats to achieve a DFT of upto 90-100 microns) over a single priming coat of self-penetrating acrylic white Primer having dilution with water in the ratio 2:1 and spreading at the rate of 8-10 sqm./Lit/coat for superior bonding and hiding. Before applying Priming coat, area must be pressure-washed with water jet having a minimum working pressure of 1400psi to remove all dirts, dust and waste products. Then, cut and open the non-structural hairline cracks less than 0.50mm in width upto 10mm with mechanical cutter and clean, moisten the surface cracks and fill the cracks with Crack-X-shrinkfree crack filler by using a putty-blade. Apply two surface coats after allowing the primer coat is cured for 4-5 hours and keep the surface coat dry for 4-6 hours to achieve the required DFT and allow it be undisturbedfor 7 more days to become fully cure. Thesurface coats should have the following technical properties : a hair line crack bridging upto 1mm; elongation of > 100% a per ASTMD 412; tensile strength of 3.5MPa per ASTM D412; adhesion strength of 2MPa as per ASTM D541; The system comes with 5-year waterproofing and 7-year paint performance warranty from the Company concerned 8 13.88, Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 9 21.8, Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and directioncomplete. 21.8.1 Upto 5mm depth and 5 mm width 10 11.49.2, Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x600 mm 11 11.47.2, Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm 12 11.48.2, Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction Size of Tile 600x600 mm 13 15.13.1, Taking outdoors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead :Of area 3 sq. metres and below 14 9.127.1, Providing & fixing decorative high pressure laminated sheet of plain /wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.1.5 mm thick 15 13.114, Melamine polishing on woodwork (one or more coat) 16 9.82, Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete 17 9.103, Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete: wooden door 18 9.83, Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete : wooden door 19 2.25, Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m 20 16.68, Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction 21 21.17 , Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction (Only weight of grill to be measured for payment). 22 21.2.2 , Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screwsetc. complete as per architectural drawings and directions. Pre-laminated particle board with decorative laminationon both sides 23 21.13 , Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.On UPS Room aluminium Three Door. 24 9.97.3 , Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than gradeAC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :200x10 mm Wooden Door & Aluminium Door in UPS Room 25 21.1.1.2 , Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at,junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : for Fixed Portion - Powder coated aluminium (minimum thickness of powder coating 50 micron) 26 21.1.2.2 , Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at,junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately):Powder coated aluminium (minimum thickness of powder coating 50 micron) 27 21.3.2 , Providing and fixing glazing in aluminium door, window, ventilator,shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) 28 10.16.1 , Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes Hot finished welded type tubes 29 12.50 , Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester topcoat 15-18microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired. The sheet shall be fixed using self-drilling /self-tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 30 12.52.3 , Providing and fixing tiled false ceiling of specified materials of size595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main T runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross T of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main T at 600 mm center to center to form a grid of 1200x600 mm and secondary cross T of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle ofsize 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting / making, opening for serviceslike diffusers, grills, light fittings, fixtures, smoke detectors etc. Main T runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard,manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. 31 0123 , Mason (brick layer) 1st class , closing of airhole with Brick & Mortar ,Making Hole for Chimney & Plastering 32 0111 , Carpenter 1st class, taking outdoor & Re-fitting the same with extra fittings-wool pile 33 0116 , Fitter (grade 1) , Plugging With silicon sealant in the Rubber Beading of Glass shutter of IRMS Laboratory 34 0114 , Beldar , Pluging With silicon sealant in the Rubber Beading of Glass shutter of IRMS Laboratory 35 LMR, Wool pile/ weather pile/Door Sweep stripfor fixing under Gap of door 36 LMR , Supplying 25 mm thick cross-linked polyethylene (XLPE) foam insulation /jacket sheet of reputed company with one side Alluminium foil and fixiing the same on thefaces of masonry wall in correct line & level by using suitable adhesive, screws & washers and pvc grips 37 LMR , Painting (two or more coats) with elastomeric flexible coating (Pidiffin-2K or likewise materials) water proofing paint of approved brand and manufacture to give an even shade. 38 LMR , Painting (two or more coats) with (Sure-Seal or likewise materials) water proofing paint of approved brand and manufacture to give an even shade 39 26.49.3 , Providing and fixing in position factory made EPS cement sandwich wall/roof/floor light weight solid core panels made of core material of EPS granule balls/beads (conforming to IS 4671:1984 and shall have density not less than 15kg per cum) adhesive, cement, sand, flyash and other bonding material in mortar state processed to form in a preset mould. The outer face on both sides of the panels will be non-asbestos fiber cement board confirming to IS 14862:2000 or Calcium silicate board confirming to EN 14306:2009 of 5mm thick each. Panel shall be laid on 6mm thick cement mortar (1 cement: 2 fine sand) mixed with chemical adhesive of 0.5kg per 50kg of cement or shall be preferably fixed into C channel made of 1.2mm thick MS plate screwed/fastenened to the slab/column/beam etc. The panel shall fixed vertically with tongue and groove joint and horizontally locked with steel bar between each other and floors and filled with cement mortar and adhesive. Panels should be used as floor & roofing with additional structural support, steel or RCC depending upon the design. All the operation shall be completed in all respect as per drawings, Manufacturers specifications and under the overall direction (Cost of all the material is included except C channel which will be paid separately). 40 10.16.2 , Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 10.16.2 Hot finished seamless type tubes 41 17.11.2 , Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :17.11.2 Size 600x450x200 mm 42 17.28.2.2 , Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 17.28.2.2 40 mm dia 43 17.69.2 , Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms 44 18.7 , Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold-water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction: Internal work - Exposed on wall -20mm dia 45 18.7.2 , Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Concealed work, including cutting chases and making good the walls-20mm dia 46 CI Civil works @ 34.55% 47 1.8.1 , Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group A 48 1.14.3 , Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2X4 sq. mm + 1 X 4 sq. mm earth wire 49 1.14.1 , Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed using medium pvc conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 50 1.14.2 , Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed using medium pvc conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 51 2.10.1 , Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole 52 1.24.1 , Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6A switch 53 1.24.2 , Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 6A/16 A switch 54 1.24.5 , Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required 6A/16 A socket outlet 55 1.27.1 , Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc.as required.2 Module 56 1.27.4 , Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc.as required.6 Module 57 1.27.5 , Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc.as required.8 Module 58 2.12.2 , Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 59 2.14.2 , Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 60 2.15.2 , Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required. 61 2.13.1 , Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps 62 MR: Supplying and fixing following size of copper conductor armoured underground cable on surface of wall /floor/ceiling including connection etc as required.4x6 sq.mm cu cable 63 MR ; Supplying and fixing 20W LED Tube light 64 MR ; Supplying and fixing Wall round fan 12 inch 65 MR ; Supplying and fixing 18 Way Normal DB 66 MR ; Supplying and fixing 10 Way Normal DB 67 MR ; Supplying and fixing 40W LED fitting (2x2 feet) 68 MR ; Supplying and fixing of 32 A DP switch 69 MR ; Supplying and fixing of 32 A DP socket 70 MR ; Supplying fixing telephone socket outlet suitable for connecting the existing EPABX system including testing, commissioning etc as required. 71 MR ;Supplying and fixing RJ 45 connector with juction box suitable for CAT 6 cable from the exisiting data network including connections testing commissioning etc as required. 72 CI Electrical 34.55%
