|
| 1 | Earth work in excavation by mechanicalmeans (Hydraulic exactor) /manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10sqm on plan) including disposal of excavated earth lead upto 50m and lift upto 1.5m disposed earth to be leveled and neatly dressed- All kinds of soil. |
| 2 | Earth work in excavation by mechanicalmeans (Hydraulic exactor) /manual meansin foundation trenches or drains( not exceeding 1.5m in width or 10sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. All kinds of soil. |
| 3 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope , ramming , consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering – all work up to plinth level |
| 5 | 1:2:4 (1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 20mm nominal size) |
| 6 | 1:4:8 (1 Cement :4 fine sand : 8 graded well burnt brick aggregate 40mm nominal size) |
| 7 | Filling available excavated earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50m and lift upto 1.5m( All kinds of soil) |
| 8 | Centering shuttering including strutting, propping etc. and removal of form work for Columns, Pillars, Piers, Abutments, Posts and Struts with wooden plank. |
| 9 | First class brick work in foundation and plinth including cost of all materials as required complete :- (1) In cement mortar 1:4 (1 cement : 4 fine sand). |
| 10 | Half brick masonry work with first class bricks in superstructure upto floor fivelevelincluding cost of all materials as required complete :- a) In cement mortar 1:4 ( 1 cement : 4 fine sand). |
| 11 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc.,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. a) Hot finished welded type tubes. |
| 12 | Providing and fixing muli bamboo champakampa tarja ( 75 mm wide) ceiling, strengthening with single split bamboo battens (both side) at 300 mm centre to centre and tied with G.I wire 1.0mm complete ( Over required beams or fixed with a frame of suitable type, which will be paid separately). As per specification. |
| 13 | Supply & installation of pre-painted Galvalume sheets for roofing/cladding (size, shape and pitch of corrugation as approved by Engineer-in-charge) in 550mpa steel grade, made out of Cold Rolled Steel coated with Zinc-Aluminum alloy coating of 43.5%Zn,55% Al and 1.5%Silicon confirming to ASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, Colour coated with high quality Polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side, Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single. |
| 14 | Supply & installation of pre-painted Galvalume sheets roofing accessories in 550mpa steel grade, made out of Cold rolled steel coated with Zinc-Aluminum alloy coating of 43.5% Zn, 55% AI and 1.5% Silicon confirming to AASTM A792/A792M and AS1397. Alloy coating AZ150/AZ70, Colour coated with high quality Polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side etc. complete as per direction of Engineer-in-charge. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. Sheet should heve protective guard film of 25 microns minimum to avoid scratches while transportation. The sheet shall be fixed using self drilling /self tapping screws with EPDM washers complete for Ridges/valley/Gutter/Flashing of width 610mm : i) 0.50mm thickness. |
| 15 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. complete as required :- i) in grating, frames, guard bar, railing, brackets, gates and similar works, all complete. |
| 16 | 12mm cement plaster of mix (1) in cement mortar 1:4( 1 cement : 4 fine sand) |
| 17 | 12mm cement plaster of mix in /c net cement punning a) in cement Mortar 1 :4(1 cement; 4 fine sand) |
| 18 | Distempering with 1st quality acrylic distemper ( ready mixed) having VOC content less than 50 grams/litre, of approved brand and manufacture to give an even shade (Payment shall be made after submission of test Certificate issued by the Manufacturer) : New work (two or more coats) over and including water thinnable priming coat with cement primer. |
| 19 | Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture ( Payment shall be made after submission of Text Certificate issued by the Manufacturer) : new work( two or more coats applied @ 1.67 litre/120 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 Sqm) |
| 20 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade (payment shall be maade after submission of Text certificate issued by the Manufacturer) : Two or more coats on new work over an under coat of suitable shade with ordinary paint ( Primer) of approved brand and manufacture. |
| 21 | Providing and laying flat brick flooring in cement mortar including cement slurry etc. complete. A) In cement mortar 1:4 ( 1 cement : 4 fine sand) |
