|
| 1 | Part ACivil Work Based on PWD BSR 2019 For Rajsamand Circle) |
| 2 | Earth work in excavationin foundation trenches or drainsincluding dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter.All kinds of soils |
| 3 | Supply & stacking good earth at site complete including loading , unloading and transportation etc &Filling available excavated earth (excluding rock) in trenches plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead upto 50 Mtr. and with all lift. |
| 4 | Providing and laying in position cement concrete including curing compaction etc. complete in spcified grade excluding the cost of centering and shuttering. All work upto plinth level using crusher broken aggreate1:3:6(1 cement:3 Coarse sand :6 graded stone aggregate 20 mm nominal size).M 10 grade nominal mix |
| 5 | Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level using crusher broken agregate1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). |
| 6 | Providing and laying cement concrete including curing, compaction etc. complete in retaining walls, return walls, walls(any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, copping, bed blocks, anchor blocks, plain window sills, fillets etc up to floor three level excluding the cost of centering and shuttering. M20 grade nominal Mix 1:1.5:3(1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size) |
| 7 | Providing and laying in position specified grade ofreinforcement cement concrete forall RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the jointsexcluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix / Design Mix |
| 8 | Providing and laying in position specified grade of cement concrete for RCC structural elements upto floor three level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement:3 coarse sand) and making good the joints excluding the cost of centtering shuttering and reinforcement for walls (any thickness) including attached plasters, buttreses, plinth and sring courses, fillets, columns, pillers, piers, abutments, posts struts etcM 25 grade design mix |
| 9 | Centering & shuttering with steel plates/ plywood sheets including strutting, propping bracing both ways and removal of formworks for foundation in basement rafts, footings, straps beams, base of columns etc upto plinth level. |
| 10 | Centering & shuttering with steel plates including strutting, propping bracing both ways with wooden members and removal of formwork upto floor three level for :Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel, beams etc. |
| 11 | Centering & shuttering with steel plates including strutting, propping bracing both ways with wooden members and removal of formwork upto floor three level for columns, pillers, posts,and struts etc |
| 12 | Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor three level. Thermo-mechanically Treated reinforcement bars (Conforming of relevent IS 1786) |
| 13 | Brick masonary in foundation and plinth with bricks of class designation75 in : Cement mortar 1 : 6 (1 cement : 6 coarse sand) add extraover item no 5.1 for brick work in super structure up to third storey.add extra over respective items all type of bricks for using clay fly ash bricks. |
| 14 | Half Brick masonry in foundation & plinth using bricks of designation 75 .Cement mortar 1 : 6 (1 cement : 6 coarse sand).Add extra over item no 5.8 for half brick masonary in superstructure up to third storey including cost of nominal hoopreinforcement. add extra over respective items all type of bricks for using clay fly ash bricks. |
| 15 | Random Rubble stone masonry for foundation and plinth in Cement Sand mortar above 30 CM thick wall in: Cement Mortar 1:6 ( 1-Cement : 6-Sand). |
| 16 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or with fixingclips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. |
| 17 | Providing and fixing M.S. sheet single leaf door shutter in angle iron frame35x35x5 mm suitabilly diagonally bracked with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint. m.s. sheet 20 s.w.g. Add extra for double leaf shutters. |
| 18 | Supplying and fixing fixed wire Gauge of 14 mesh X 24 Gauge to the Metal frame of rolled section by metal beading 20X3mm with suitable screw at not exceeding 150mm distance. |
| 19 | Providing and fixing square bars or other flat welded to window ventilators etc. |
| 20 | Grading roof for water proofing treatment with: Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)with water proofing compound as per manufactures specification. |
| 21 | Providingbatta (gola) 75x75 mm in cement concrete 1:2:4 (1 cement : 2coarse sand : 4 stone aggregate 10mm and down gauge) includingfinishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : |
| 22 | Polished blue kota stone flooring skirting laid over 20 mm thickbase of CM 1:4 and jointed with grey cement slurry to match the shade of the slab including rubbing and polishing complete. for area of each slab from 2001 to 5000 sq. Cm 25 mm thick slab. |
| 23 | Polished blue kota stone slab in steps, walls, pillars, having fine machine cut edges laid on 12 mm (average)thick cement mortar 1:3(1 cement: 3 Course sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete . 25mm thick slab area 901 to 2000 sq. cm |
| 24 | Polished blue kota stone slab in steps, walls, pillars, having fine machine cut edges laid on 12 mm (average)thick cement mortar 1:3(1 cement: 3 Course sand ) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete . 25mm thick slab area 901 to 2000 sq. cm |
| 25 | Random rubble Dry stone Kharranjaunder floor |
| 26 | Plaster on new surface on wall in cement sand mortar 1:6 including raking of joints etc. complete fine finish: 12mm thick |
| 27 | Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish: 20mm thick |
| 28 | 6 mm thick cement plaster to ceiling of mix 1:3(1 cement: 3 fine sand) |
| 29 | Applying Birla/JK white cement based putty over cement plaster surface for making even surface. |
| 30 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding. New work (two or more coats) over and including scrapping and priming coat with cement primer. |
| 31 | Painting exterior surface of wall with 100%acrylicexterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering,primer,putty, etc complete in all respect. New work |
| 32 | Painting withenamel paint of approved brand and manufactureto give an even shade : two or more coats on new work . |
| 33 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 110 mm dia |
| 34 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: Bend 87.5110mm dia |
| 35 | Pipe Clip110 mm dia |
| 36 | PART-C (Electric Work) Based on BSR PWD |
| 37 | Wiring of light point/ fan point/ exhaust fan point/ call bell point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS: 694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked (IS:9537 P- II) rigid steel conduit & it\"s all accessories, round tiles, 18 SWG G.l.box with earth terminal, 6 A switch, 3 pin ceiling rose/ Lamp holder / 3 point Connector, 3.0 mm thick ISI marked phenolic laminated sheet, pvc bushes, check nuts, Al. alloy/ cadmium plated iron screws 20 mm cup washers etc. All as per pre approved by Engineer in charge, making connections, testing etc. complete as required. For specification of copper Conductor, Phenolic Laminated sheet\"s & Electrical/ Wiring accessories refer Chapter E04, E 05 & E - 07. For additional technical parameters of products/ work refer Annexure \"A\" attached with this BSR. Light point Short point (up to 3 mtr.) |
| 38 | Medium point (up to 6 mtr) |
| 39 | Long point (up to 10 mtr) |
| 40 | Wiring of 3/5 pin 6 amp. Light plug point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) in recessed ISI marked ( IS:9537 P II) rigid steel conduit & it\"s all accessories, required size 18 SWG, G.I. box with earth terminal, 6 A switch, 3/5 pin 6 A socket, 3.0 mm thick ISI marked phenolic laminated sheet, pvc bushes, check nuts, Al. alloy/ cadmium plated iron screws 20 mm cup washers etc. all as per pre approved by Engineer in charge, making connections, testing etc. complete as required. For specification of copper Conductor, Phenolic Laminated sheet\"s & Electrical/ Wiring accessories refer Chapter E-04, E-05 & E-07. For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR. |
| 41 | S&F following sizes (dia.) of ISI marked (IS:9537 P-II ) rigid steel conduit of apropriate thickness related to its dia as per PWD specification for electrical Works along with accessories in recessed using saddles, clamps, fasteners, pvc bushes, check nuts, screwas etc. as required including cutting the wall and making good the same as required all as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer Annexure \"A\" attached with this BSR |
| 42 | Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130: 2013 of 1.1 kV grade. Wire should be made from 99.99% purity copper, class 5 stranding in acc. to IEC 60228 for lower watt loss, oxygen free (<10 ppm) for less chances of oxidization and higher silver content for gives better conductivity, insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4,, in existing surface or recessed PVC/ MS conduit/casing capping including all as per pre approved by Engineer in charge, making connections, etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR.2 x 1.5 sq. mm |
| 43 | 2 x 2.5 sq. mm |
| 44 | Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/C tripping characteristic as per type of load and site requirement) 4KV impulse withstand voltage, as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947 2, low watt losses, trip free mechanisum, energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm., conductorline load reversibility, label holding facility, IP 20 contact protection and fitted with existing distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A rating including making connections, testing etc. as required.. OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer Annexure \"A\" attached with this BSR. |
| 45 | Providing & Fixing of IK09 recessed/surface mounting heavy duty horizontal type sheet steel of 1.6 mm thick Distribution board as per PWD specification for electrical Works ISI marked conforming to IS-13032 & 1S-8623 / conforming to IEC 61439-3. Phosphatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link, neutral link, earth link, connecting wire of suitable rating and din bar, masking sheet, including making internal DB terminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.OEM shall have submit NABL/ CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR.. 8 Way (8 O/G +2 I/C ) |
| 46 | Providing & Fixing of IP40 LED Recessed / Surface Mounted, Round / Sqaure Non-Dimmable Back lit SMD Mid Power LED Downlight with die-cast aluminum housing & Heat Sink for heat dissipation with UV Stabilized non yellowish Diffuser with internal/external BIS complience 2.5 KV surge protected Isolated driver, with Short & Open circuit protection, having efficiency> 85% and in compliance to IEC standards. System Lumen efficacy of ≥ 120 lm / watt, THD < 10 % ,p.f.20.95, CRI >80, life time of minimum 50000 Burning Hours with, 70% of intial Lumen maintaned till life ends, CCT 3000 K / 4000 K / 5700°K /6000°K/6500 K (As per ANSI Bin) maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/Screen printing on housing.OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge foe additional technical parameters of product/ work, refer Annexure \"A\" attacheded with this BSR. |
| 47 | Providing & Laying P.V.C. / XLPE insulated & P.V.C.sheathed Un-armoured / Armoured aluminium cable of 1.1 KV grade as per PWD specification for electrical Works in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench with filling of excavated earth in trench, on existing cable trays or on surface etc. including making necessary connection, testing etc. as required of size and as per points (a), (b), (c), mentioned below: (a) Material: H4- Grade aluminium conductor ofpurity >99.6% & as per IS:1554 P-I/IS:7098 P-1(b) conductor shall have electrolytic aluminium confirming to IS 8130, IS 3975-1999 for armouring of cables in armoured cable items, IS 5831 for sheath, IS 10810 (Part 0 to 64) for testing procedures.(c) OEM Must have ISO 9001 & 14001 certifications for quality assuarance & its own in house NABL lab setup for all testing facilities for cables. Appropriate type test certificate / OEM test report shall be submitted. All above as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR. as required of size 6 sqmm, 3 core armoured |
| 48 | Providing & Fixing of ISO Certified company made BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan as per PWD specification for electrical Works, conforming to IS:374-2019, & IS:1885 -P-V 1981. with down rod up to 30 cm with secondary support safety cable (steel wire), cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR. 1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5) |
| 49 | Providing & Fixing of ISI marked (IS:1258) 6 amp batten/angle lamp holder as per PWD specification for electrical Works, made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screws including making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR. |
| 50 | P & F 18 swg M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR. |
| 51 | Providing & Fixing of 18 SWG G. I. / M.S. Sheet boxes as per PWD specification for electrical Works, duly finished with two coats of red oxide and with earthing terminal of following sizes (nominal size) in recessed/surface as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR.. 175 mmX 100 mmX60 mm |
| 52 | Providing & Fixing of paper phenolic resin bonded laminates confirming to IS 2036 1995 for boxes/ frames including making holes for switches etc, with brass/ zinc plated screws, washers, nut and bolts as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR. |
| 53 | Providing & Fixing of 240/415 V isolator as per PWD. specification for electrical Works with ISI marked IS:13947. III/conforming to IEC 60947-3, suitable for AC22A utilization catagory, 4KV impulse withstand voltage, true contact indication, Red colour dolly / lever shall have single mould covering over all poles for operation, two position din rail mounting, minimum phase termination capacity of 35sq.mm., label holding facility, IP 20 contact protection and fitted with existing distribution board / sheet including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, Annexure \"A\" attached with this BSR. |
| 54 | Providing & Fixing of non modular socket size flush type 180 watt rotary minimum 5 step fan regulator as per PWD specification for electrical Works, ISI marked (IS:11037) made out from industrial grade Polycarbonate or fire resistant ABS material including making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work refer Annexure \"A\" attached with this BSR. |
| 55 | Providing & Fixing of of 3 pin 6 amp. flush type non modular socket as per PWD specification for electrical Works, made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal with Porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \"A\" attached with this BSR. |
| 56 | Providing and fixing of non modular power plug point accessories as per PWD specification for electrical Works with 18 SWG GI box of size 175 x 100 x 60 mm with earthing terminal/connector on recessed/surface with suitable size phenolic laminated sheet (IS: 2036 1995) cover including cost of 16 amp. Switch (IS:3854) and 3/6 pin 16 amp. socket outlet [ as per detailed in respective item in BSR], making connection, testing, etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/work, refer Annexure \"A\" attached with this BSR. |
