|
| 1 | Page No. - 233/1Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finishedconforming to IS: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - InCharge.(Payment will be made on finished length of the work).(A) In 10-12 Micron thickness Annodizing filmj) Fixed partitions.(Unsupported length of vertical member more than 1.5 mtr. Height of both endsof vertical member restrained but panels within 0.9 sq.m.)i) Top , bottom & side member |
| 2 | ii) Intermediate member |
| 3 | Page No. - 241/2 ( D )Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units:-(D) Partly glazed and partly panelled partition or fixed glazing made of extruded and anodised alloy aluminium sections, fabrications after cutting to proper shape and size, drilling and aligning fitted with inbuilt locking arrangement cutting the glass / board (prelaminated / particle / block) to requisite shape and size moulding the edges fitted and fixed glazing clips and dry set neoprine /EPDM gasket, along with all other necessary arrangements for fixing the partition to walls, floors, beams, columns polysulphide sealant for water proofing if necessary complete in all respect as per drawing and specifications and direction of the Engineer in charge. The rate includes the hire charge of all tools and plants, adhesive, joineries such as screw, fastener but excluding the cost of extruded aluminium sections, EPDM gasket, glass, board, glazing clips, lockingarrangement, etc.I) For partitions using section of size:a) 63.50 mm x 38.10 mm |
| 4 | Page No. - 250/27 Providing and fixing exterior quality Aluminium Composite Panel (ACP) wall cladding on existing Al. /MS frame work with GI brackets, ACP fixed on the existing frame work by folding the edges of ACP panel (Engraving the rear surface of ACP sheet) with CP angles, cleats and strainless Steel screws forming groves at the periphery of ACP panel. Such grooves filled with foam and silicon sealant etc. complete with all materials (but including the cost of silicon sealant), labour, scaffolding and all other incidental charges complete in all respect as per specification and direction of Engineer-in-charge. (Mode of payment is on finished surface area of ACP)(a) 3mm thick (0.25mm Al.+2.5mm LDPE +0.25mm Al. PVDF coating) |
| 5 | Page No. - 233/1Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized (with required film thickness and specified colour / natural) matt finishedconforming to IS: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer - InCharge.(Payment will be made on finished length of the work).(A) In 10-12 Micron thickness Annodizing filmb) 3- track sliding windowi) Bottom frame |
| 6 | ii) Top , bottom & side member |
| 7 | k) Movable door shutter.i) Door frame. (Top & sides) |
| 8 | ii) Shutter : Top rail |
| 9 | Bottom rail |
| 10 | Lock rail |
| 11 | Door vertical |
| 12 | Glazing cleap |
| 13 | d) Shutter for all track sliding window.i) Bottom & Top member. |
| 14 | ii) Style side member. |
| 15 | iii) Interlock member |
| 16 | Page No. - 241/2 Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units:-(A) ii ) 3 /4 track sliding window |
| 17 | (B) Partly glazed partly panelled or fully glazed single leaf alunminium swing door made of extruded and annodized alloy aluminium sections, fabrication including cutting to proper shape and size, drilling and aligning, fitted with heavy duty hydraulic action floor sping placed in the floor with mending damages,with top pin assembly of approve make and brand, fitted with in built locking arrangement, flush bolt, glazing clips and all other necessary fittings, fixtures, adhesives and joineries, cutting glass of approved make to requisite shape and size fitting with dry set neoprene or EPDM gasketing, cutting to requisite shape and size panel board (prelaminated particle block) fixing them with glazing clips as per drawing, specification and direction of Engineer in charge. |
| 18 | Page No. - 242/5Supplying concealed type heavy duty PVC headed aluminium tower bolt for double leaf doors as per approved make and brand as per direction of Engineer-in-Charge.(a) 200 mm long |
| 19 | Page No. - 242/6Supplying PVC rollers for sliding windows as per direction of Engineer in charge. |
| 20 | Page No. - 242/7Supplying maruti lock (100mm) |
| 21 | Page No. - 242/8Supplying EPDM gusket of approved make and brand as per direction of Engineer in charge.i) For sliding windowsa) \" T\" shaped EPDM gasket for frames |
| 22 | b) \"U\" shaped EPDM gasket for frames |
| 23 | Page No. - 243/9 Supplying bubble free float glass of approved make and brandconforming to IS: 2835-1987.ii) 4mm thick coloured / tinted / smoke glass. |
| 24 | Page No. - 244/13 (A) Supplying Aluminium casted body hydraulic door closer as per I.S.I |
| 25 | Page No. - 244/13 (B) Supplying 125 mm. Dia acrylic handle for aluminium door as perapproved make & brand.(a) Natural Colour |
| 26 | Page No. - 244/13 (C) Supplying Heavy Duty Aluminium Handle (EBCO Type) (Natural White) |
| 27 | Page No. - 244/ 13(D) Supplying Aluminium casted body Butt Hinge (KOBRA type).(Natural white) |
| 28 | Page No. - 244/ 13(F) Supplying Zinc powered coated star lock (Natural White) |
| 29 | Page No. - 198/4Removing old scales, blisters etc. of interior surface of walls,ceiling by scraping etc. and preparing smooth and even surface with rendering or cement mortar (1:2) (as necessary), to make the surface suitable for receiving distemper. (Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge) |
| 30 | Page No. - 195/7 Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparingthe surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC.(b) Two Coatii) Solvent based interior grade Acrylic Primer |
| 31 | Page No. - 201/4 Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : (Two coats) ii) Luxury Quality |
| 32 | Page No. - 200/1 (a) (a) Priming one coat on steel or other metal surface with synthetic oilbound primer of approved quality including smoothening surfaces by sandpapering etc. |
| 33 | Page No. - 200/2 (A) Painting with best quality synthetic enamel paint of approved makeand brand including smoothening surface by sand papering etc. includingusing of approved putty etc. on the surface, if necessary :(b) On steel or other metal surface :With super gloss (hi-gloss) -(iv) Two coats (with any shade except white) |
| 34 | Page No. - 200/1 (b) (b) Priming one coat on timber or plastered surface with synthetic oilbound primer of approved quality including smoothening surfaces by sandpapering etc. |
| 35 | Page No. - 200/2 (A) Painting with best quality synthetic enamel paint of approved makeand brand including smoothening surface by sand papering etc. includingusing of approved putty etc. on the surface, if necessary :(a) On timber or plastered surface :With super gloss (hi-gloss) -(iv) Two coats (with any shade except white) |
| 36 | Page No. - 167/22 Supplying,fitting & fixing in position suspended false ceiling with frame work ofaluminium hollow section of size 50mm X 25mm (2.0mm thickness) combined with aluminium corners of size 38mm X 25mm, suspended by aluminium hollow tube section of size 38mm X 25mm having size of 600mm X 600mm ceiling with aluminium composit panels (ACP) - Interior grade of thickness 3.0mm comprising of proctective film, polyester coating, primer, aluminium coil, adhesive film,polyethylene core again with one layer adhesive film, aluminium bottom coating and finally service coating as per manufacturer\"s specification finished with aluminium screw and silicon sealent complete in all respect including all incidental charges etc. as per direction of Engineer-in-charge. |
| 37 | Page No. - 66/36 ( 3rd Corrigenda, dt :- 04.06.2018 )Supplying and laying true to line and level vitrified tiles of approved brand (size not less than 600 mm X 600 mm X 10 mm thick) in floor, skirting etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry back side of tiles using cement @ 2.91Kg./sqM or using polymerised adhesive (6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per sqM below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles / epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer\"s specification and direction of Engineer-in-Charge.(I) With application slurry @1.75 kg/ Sq.m, 20 mm sand cement mortar (1:4) & 2 mm thick cement slurry at back side of tiles, 0.2 kg/ Sq.m white cement for joint filling with pigment.(A) Deep Colour & White |
| 38 | Page No. - 64/ 35 ( A ) a (i)( 3rd Corrigenda, dt :- 04.06.2018 )Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.(D) WallWith Polymerised Adhesive & Epoxy grout pointingWith Polymerised Adhesive and Epoxy grout pointing including spacer- 2 mm ( When Tiles are laid over existing hard ready surface)(b) Area of each tile above 0.09 Sq.m [using adhesive 4.5 mm thick](i) Coloured decorativeGround Floor |
| 39 | (A) FloorWith Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.(a) Area of each tile upto 0.09 Sq.m(i) Coloured decorative Ground Floor |
| 40 | Page No. - 198/5 Rendering the Surface of walls with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) |
| 41 | GST Item (Effect from 18.07.2022)18 % GST on Estimated Cost of Sl No- 1 to 40 |
| 42 | Labour Welfare Cess Item (Effect from 01.11.2017) 1% Labour Welfare Cess on Estmated Cost of Sl No -1 to 41 |
