|
| 1 | Providing and installation of 8 in 1 combination set:-*PRODUCT DIMNSIONS: - D.I.A 4000mm*SAFE WORKOUTAREA: - D.I.A. 5000mm*Combination made from “B” Class G.I. pipe. The octagonal structure is made up of 100mm NB “B” class GI pipe. Round plate of 250mm diameter & 10mm thickness is welded at bottom of octagonal Structure. The links are made up of 25mm NB “B” class G.I. pipe. The handle and seat frame of seated puller is made from 32mm NB “B” class G.I. pipe. For the assembly different bushes are used which is made from seamless pipe of 50mm OD and 5mm thickness & 5mm solid bar is used. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330mm x 300mm x 2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20mm with no sharp edges. Leg press footrest consists of 25 NB diameter hardened low carbon steel material. The nut Bolts used for assembly are made from S.S. material. The bushes (stopper) used to avoid the collusion made from Poly Urethin Plastic material of 50mm diameter. Surfing frame is of 32NB made from “B” Class G.I. pipe. 300mm diameter x 10mm thick plate can be used for rotating sear of seating twister with 50 NB vertical G.I. pipe. Closing caps made from high quality FRP material which is of 2mm thickness. The pints used are made up of 17mm diameter solid bar. The bearing used are of “6205” permanent lubricated sealed bearing of reputed make. The nut bolts used for assembly are made from M.S. pre-galvanized material. A17, A24, A34 circlips are used for assembly. The footrests are made from casted Aluminum material. Having sizes 130mm x 310mm x 5mm thick. With the support of 310mm x 130mm x 3mm thick MS plate. It has Bolting provision for mounting on concrete slab. |
| 2 | Providing and installation of Air Walker-DIMENSIONS: - 1060mm (Length) x 810mm (Width) x 1600mm. (Height). SAFE AREA:- 2.0 Meter x 1.8 MeterAir Walker Equipment made from “B” class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. Make of G.I. Pipe will be of Apollo, Tata, Jindal, Swastik, Zenith or Siddharth. The main frame pipe is of 80mm NB made from“B” Class G.I. Material which is bending at the radius of 250mm. The Sleeve frame is of 100 OD and M.S. Seamless Pipe with thickness 5mm. This sleeve can be easily disassembled from main frame. The bottom support of M.S. round plate of 0250mm & 10mm thick. The leg movement frame is of 32NB made from “B” Class G.I. pipe. This link is supported with MS flat of size 60X8mm. The handle frame is of 25NB made from “B” Class G.I. Pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” class welded with M.S. round plate of 0250mm & 10mm thickness and 20mm x 25mm M.S. angles of 3mm thickness and 20mm x 40mm CRC square pipes. Foundation cover Closing Cap is made from FRP Material with 0.7mm thickness. Closing Caps are made up of high quality reinforced Plastic material. A24 circlips are used for assembly. The bearings used are “6205zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel galvanized nuts & bolts are used for assembly. The powder coating is done by Pure Polyester powder of Ackzonoble or Berger Paints with 60 to 70 micron thickness. The footrests are made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 250mm X 115mm X 3mm thick MS plate. To build structure bushes are used which are made fromM.S. made of SS 304 used on nylon cap mounted on pins to protect and pins from rain and dust. |
| 3 | Providing and installation make TRIPLE STANDINGTWISTER – DIMENSIONS: - 1150mm (Length) x 1150mm (Width) x 1580mm (Height). SAFE AREA: - 02.1Mtr.Triple Twister made from “B” Class G.I. Galvanized (G.I.) Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. Make of G I Pipe will be of Tata, Jindal, Swastik, Zenith or Siddharth. The Center Pipe is of 80NB made from “B” ClassG.I. pipe. The bottom support welded is of M.S. round plate of 0250mm & 10mm thick. The standing frame is of 32NB made from “B” ClassG.I. pipe. The handle frame of triple twister is of 25mm NB made from “B” class G.I. pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80NB “B” class welded with M.S. round plate of 0250mm & 10mm thick. Main pipe supported with 25 mm x 25 mm M.S. angle of 3mm thickness and 20mm x 40mm CRC square pipe of 3mm thickness. The standing plate is fitted on the framemade up of 0 80 NB GI. Pipe. M.S. Round Plate of size 0300mm x 10mm thickness. Closing Caps are made up of high quality Fiber reinforced Plastic material. The Pins used are made up of 0 35 mm SAE 8620 bright material. The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts are used for assembly. The powder coating done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness. |
| 4 | Providing and installation of make LEG PRESS DOUBLE -*DIMENSIONS: -1840mm (Length) x 360mm (Width) x 1560mm. (Height).*SAFE AREA: - 2.8Mtr x 1.4Mtr.*Leg press equipment made from “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters.*Make of G I Pipe will be of Tate, Apollo, Jindal, Swastik, Zenith or Siddharth.*The center pipe is of 100mm NB made from “B” Class G.I. pipe.*The Sleeve frame is of 100 OD and of M.S. Seamless Pipe with thickness 5mm. This sleeve can be disassembled from main frame.*The bottom support of M.S. round plate of 0250mm & 10mm thick.*The remaining outer frame is of 32NB made from “B” Class G.I. pipe.*The foundation used for fixing is structure and made from center pipe of G.I. of 80mm NB “B” Class welded with 25mm X 25mm M.S. angles of 3mm thickness and 20mm x 40mm CRC square pipe of 3mm thickness.*Seat & Back rest provided are made up of MS deep draw quantity of 2mm thickness with no joint with uniform outer edge radius 20mm.*The footrests are made from casted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 310mm X 130mm X 3mm thick MS plate.*The frame of footrests made up of 25NB “B” Class G.I. pipe.* Closing Caps are made up of high quality Fiber reinforced Plastic material.*To build structure bushes are used which are made from M.S. seamless pipe of 50mm O.D. and 5mm thickness.*The pins used are made up of 025mm SAE 8620 bright material.*The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed Brand (SKF/FAG).*High tensile steel with galvanized nut bolts are used for assembly.*The cerclips used for assembly are of A24mm.*The powder coating done with Pure Polyester powder of Ackzonoble or Berger with 60 to 70 micron thickness. |
| 5 | Providing and installation of ARM PULLAR DOUBLE-DIMESIONS: - 1900mm (Length) x 740mm (Width) x 1920mm (Height). SAFE AERA: - 1.2Mtr x 3Mtr.Seated puller equipment made up of “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. Make of G I Pipe will be of Apollo, Tata, Jindal, Swastik, Zenith or Siddharth. The center pipe is of 100NB made from “B” ClassG.I. pipe. Bottom support is of M.s. round plate of 0250mm & 10mm thickness is welded. All linkages are made up of 25NB “B” Class G.I. pipe. The handle frame is of 32NB “B” Class G.I. pipe. The seat frame is of 32NB “B” class G.I. pipe. To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80NB “B” class. Welded with M.S. round plate of 0250mm & 10mm thick. Main pipe supported with 25mm X 25mm M.S. angles of 3mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Foundation cover Closing Cap is made from FRP Material. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330mm X 300mm X 2mm thickness and form radius of 20 mm with no sharp edges. Closing Caps are made up of high quality Fiber reinforced Plastic material. Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. The bearings used are of “6205zz” and “6203zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG). High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used of assembly are of A16. The powder coating done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 micron thickness. |
| 6 | Providing and installation of SURF BOARD SINGLE -*DIMENSIONS: - 910mm (Length) x 860mm (Width) x 1400mm. (Height).*Safe Area: - 1.39Mtr x 1.27Mtr.*Surf Board Equipment made from “B” Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters.* Make of G I Pipe will be of Tate, Apollo, Jindal, Swastik, Zenith or Siddharth.*The center pipe is of 100mm NB made from “B” class G.I. pipe.*The sleeve pipe is of 125mm OD seamless pipe with thickness of 5mm and bolted to main frame with M10 SS bolts.*The bottom support welded of M.S. plate of 0250mm & 10mm thickness.*The handle frame is of 25NB made from “B” class G.I. pipe.*The paddle frame is of 25NB made from “B” Class G.I. pipe is supported with 70x8mm bend M.S. flat and can be replaceable.*The foundation used for fixing is a structure and made from center pipe of G.I. of 80NB “B” class welded with M.S. round plate of 0250mm & 10mm thick. Main pipe supported with 25mm x 25mm M.S. angles of 3mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness.*Bushes are used 70mm Outer Diameter with 5mm thickness is used.*The footrests made from Aluminum casting material of size 320mm x 270mm x 5mm.*For support to footrest 200mm x 250mm with 3mm thickness M.S. Plate used.*Closing Caps are made up of high quality Fiber reinforced Plastic material.*The pins used are made up of 035mm SAE8620 bright material.*The bearing used are of “6007zz” permanent lubricated sealed bearing of reputed brand (SKF/FAG).*High tensile steel with galvanized nut bolts are used for assembly.*The cerclips used for assemble A24.*The powder coating is done with Pure Polyester powder of Ackzonoble or Berger with 60 to 70 micron thickness. |
| 7 | Providing and installation of SHOULDER BUILDER DOUBLE :- General Information:Product Area: - 1.5 X 0.8 meter Safe Play Area: - 2.5 X 1.8 meter Technical Specification:25 NB Galvanized pipe bend to form ring and spokes consists of 20 NB G.I. pipes the connect to each other of form a pair of wheels of FOREARM TWIRT. These wheels are mounted on both ends of 40 NB G.I. pipe bend with specially designed bearing housings and shaft assemblies. This bend pipe is fixed to main frame of 80 NB G.I. pipe. Handle is fixed over the pipe ring for free movement of wheels. All pipes are uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe bend closed by GI/HDPE caps for user safety against entrapment. Handle for rotating the ring fixed. |
| 8 | Providing and installation of CROSS TRAINER-*DIMENSIONS: - 1320mm (L) x 600mm (W) x 1650mm. (H).*SAFE AREA: - 2.3 x 1. 6Mtr.*Cross trainer equipment made from “C” Class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters.* Make of G I Pipe will be of Tate, Apollo, Jindal, Swastik, Zenith or Siddharth.*The main frame Pipe are ofRectangle Pipe of size 90 x 48mm Pipe & square pipe of 40 x 40mm .*The bottom support of M.S. round plate of 250mm & 10mm thick.*The Handle of 32mm ID is used for fixing a structure and made from center pipe of G.I. of 80NB “C” class welded with M.S. round plate or 0250mm & 10mm thick. Main pipe supported with 25 mm x 25 mm M.S. angles of 3 mm thickness*To build structure bushes are used which are made from seamless pipe of 60mm OD. With 3mm thickness.*The footrests are made from Aluminum casing material of size 100mm X 300mm X 5mm thickness and mounted on M.S. Plate of Size 130mm x 310mm x 3mm thick.*Closing Caps are made up of LLDPE Plastic material.*Pins used of Diameter 25 & 32mm are made up from bright Material.*The Bearings used are of “6205zz” permanent lubricated sealed bearing of reputed brand.*High tensile galvanized nuts and bolts are used for assembly.*The powder coating is done with Pure Polyester of Ackzonoble or Berger Paints with 60 to 70 Micron assembly.* A 24 mm serclips are used for assembly. |
| 9 | Providing and installation of SINGLE CHEST PRESS –*DIMENSIONS: - 900 mm (L) x 710mm (W) x 2100mm. (H).*SAFE AREA: - 2.0Mtr x 1.7Mtr.*Chest press equipment made up of “B” Class G.I. pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters.* Make of G I Pipe will be of Tate, Apollo, Jindal, Swastik, Zenith or Siddharth.*The center pipe is of 100NB made up of “B” Class G.I. pipe.*The bottom welded with support of M.S. round plate of 250mm & 10mm thickness.*The connecting pipes are made up from 25NB “B” Class G.I. pipe.*The handle frame is made up from 32NB “B” Class G.I. pipe.*To build structure bushes are used which are made from M.S. seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used.*The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “B” Class Welded with M.S. round plate of 250mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3mm thickness.*Foundation cover Closing Cap is made from LLDPE Material.*The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 300 mm X 250 mm X 2 mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.*Closing (Bearing) Caps are made up of LLDPE material.*Pins used of Diameter 25mm are made up from bright material.*The bearings used are of “6205zz” permanent lubricated sealed bearing of reputed brand.*High tensile steel with galvanized nuts & bolts are used for assembly.*The serclips used for locking is made up of A24 mm.*The powder coating done with Pure Polyester powder from Ackzonoble or Berger Paints with 60 to 70 micron thickness. |
| 10 | Providing and installation of 5 in 1 combination (shoulder press+ chest press+ knee chair+ seating and standing twister)• PRODUCT DIMENSIONS: - 2410mm (Length) x 1720mm (Width) x 2350mm (Height).• SAFE WORKOUT AREA: - 4500mm (Length) x 4500mm (Width).Combination made from “B” Class G.I. pipe. The center pipe is of 100mm NB pipe. Round plate of 248 mm diameter & 9mm thickness is welded at bottom. The links are made up of 25mm NB pipe. The handle and seat frame of shoulder press is made from 32mm NB pipe. For the assembly different bushes are used which is made from seamless pipe of 50mm OD and 5mm thickness & 50mm solid bar is used.Chest press frame is of 32mm NB pipe. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330mm X 300 mmX1.8mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. The chest press footrest consists of 25 NB pipe. The pins used in are made up of Φ25 mm, Φ35mm & Φ45mm bright material. The Nut Bolts used for assembly are made from height tensile steel with galvanized material. The bushes (stopper) used which are made from Poly Urethin Plastic material of 48 mm diameter. Surfing pedal is of 32NB pipe. Knee chair handle frame is of 32NB pipe. 298mm diameter x 9mm thick plate is used for rotating seating of standing twister with 50NB pipe. Closing caps made from best quality HDPE/LLDPE material in attractive colors. The pins used are made up of 17mm diameter solid bar. The bearing used are of “6203”, “6205”, & “6007” permanent lubricated sealed bearing of reputed make. The nut bolts used for foundation assembly are made from M.S. pre-galvanized material. A17, A24, A34 circlips are used for assembly. The footrests are made from casted Aluminum material, having sizes 125mm X 305mm X 4mm thick. With the support of 305mm X 125mm X 2.9mm thick MS plate.It has Bolting provision for mounting on concrete slab. Polycarbonate sheet is used for roof with supporting frame which is made from Dia. 25mm NB pipe. MS 7.8mm thick round plate is used for splitting roof structure from main frame. Handle grips are provided which is made of high quality rubber material. The powder coating done with Pure Polyester powders from Ackzonoble or Berger Paints with minimum 60 to 70 micron thickness. |
| 11 | Providing and installation of multi action play system & other children playground equipments consisting of the following items the area of 8 mtr x 7 mtr and required safe area is 9 mtr x 8 mtr(1). Square Deck 5 feet height - The platform is made in fiber reinforced plastic. The top of platform is anti skid surface with multi colour pigmented resin .The back coat of fiber reinforced plastic is such that the mat strands are not visible and the surface is tack free. At the top of the deck there is a window canopy shade to the children playing on it.(2).Wave slide 5’ height - The Wave Slide chute with top entry module shall be made by FRP, the slide thickness thickness will be 5 mm with uv pigment to avoid colour fading.. The Wave shape is given in such a manner that it will not give any jerk or bump to the rider. The chute has its end such as it causes safe landing of the child. The landing portion is horizontal with respect to the ground.(3). FRP Straight slide 5 feet height-The Straight Slide chute with top entry module shall be made by FRP, the slide thickness for total will be 5 mm for both side finished(4). ROCK CLIMBER 5’ HT. The rock climber is made up of fiber reinforced plastic. Rocks are molded on same platform and it has gradient from the ground. The climber is supported by 25 IDGI pipe at the bottom for ground support.(5) STEEL BRIDGE 8’ LONG-The Steel bridge is made from 40x40x5 with CRC sheet 18 gej& laminated by FRP non skidchequred sheet.it has railing made from FRP molded process with support of 20 NB GI pipe with the help of 80 IDGI pipe and 80 x 20 NB nylon clamps.(6). FRP CANOPY- Square canopy should be made up of fiber glass reinforced plastic with 3 to 4 mm thickness with glossy finish and paint by PU paint in Multy colors.(7).Frp Ladder 5 feet height- Frp ladder should be made by fiber glass reinforced plastic with 4 to 5 mm thickness with antiskid surface.(8). Frp Railing - The railing is made in FRP molded process .The railings are attached to each other with the help of 20 IDGI pipe.(9). Hand railing- Hand railing should be made by 20 mm IDGI pipe to proper control for children’s. There is no any sharp corner not seen on the railing.(10). Frp RINDEER andFrp FLOWER- This is made from Fiber glass reinforced plastics for the attraction.(11). DOUBLE SWING WITH FRP BUTTERFLY-The leg support of double swing is made by 60 MM IDGI pipe while the top bar Is of 60 MM IDGI pipes. The GI pipes are powder coated. The swing seats are made from 9 mm thick antiskid chequered reinforced rubber belt or 9 MM thick. FRP seating arrangement. The ball bearings are mounted inside a specially designed clamp.(12). Spiral climber 5 feet height-Spiral climber made up of 25 NB GI pipes. The spiral structure is suitably bent and is kept standing with vertical 40 IDGI pipe support.All the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. The pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. The pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. |
| 12 | Providing and installation of hanging Climber:- Safe Play Area -3.4 mtr. X 2.2 mtr. DiaArea: - 2.4 mtr. 1.2 mtr.Height- 2.4 mtr.It required area 2.4 mtr x 1.2 mtr& height 2.4 mtr and leg support should made up of 50 mm IDGI pipe outer frame should be made by 32 mm IDGI pipe in main frame joint with 20 mm IDGI pipe in handrails/inner frame in dia. Ladder should be made by 20 mm IDGI pipe. And connected with proper fitment like welding, fastener.All the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. The pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. The pure polyester powder coating (oven baked) done on the pipes extend the life of equipments.And install by C.C. base system as per order by engineer in charge Age capacity 6-12 Year. |
| 13 | Providing and installation of Snake Climber: - Safe Play Area -4.5 mtr. X 2.0 mtr.Area : 3.6 x 1.0 MtrHeight- 2.4 mtrIts height 2.4 mtr. And Length should be 3.6 mtr. And width should be 1.0 mtr. And made by 50 mm IDGI pipe in vertical support and 32 MM NB pipe in outer frame. Handrails should be made by 25 mm IDGI pipe. Leg support should be 50 mm IDGI pipe. Ladder should be madeby 20 mm IDGI pipe.All the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. The pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. The pure polyester powder coating (oven baked) done on the pipes extend the life of equipments.And install by C.C. base system as per order by engineer in charge Age capacity 3- 8 Year. |
| 14 | Providing and installation of Swing Double Seater : - Safe Play Area -4 mtr. X 2.5 mtr.Area: - 3 mtr. X 1.5 mtr. Height- 2.4mtrIts total required area 3 mtr. X 1.5 mtr. And height shall be 2.4 mtr. From ground level top bar of swing is made by 60mm IDGI pipe. And 4 nos. of leg support pipe should be 60mm IDGI pipe.Top bar attach with 2 nos. of alloy steel coasting bearing with GI chain. Seating arrangement of swing is made up of 10mm thick. Anti skidchequered reinforced rubber belt. Bearing should be covered by specially design nylon clamp. The pure polyester powder coating (oven baked) done on the pipes extend the life of equipments.And install by C.C. base system as per order by engineer in charge. |
| 15 | Providing and installation of EagleSee Saw:- Safe play Area – 2.5 mtr. X 3.5 mtr.Area – 1.5 mtr. X 2.5 mtr. Height – 0.8 mtr.It’s required area 1.5mtr x 2.2mtr. Main frame should be made by 80mm IDNB Centre pipe with proper fitment for installation of see saw. Handle should be made by 25 mm IDNB pipe. Total height 0.5mm from ground level. 2 nos. of sheet made by 3 mm thick FRP with proper seating arrangement grouted in CC. foundation base All the sharp edges and corner properly grinded to Give Smooth finishing so that children are not hurt with playing on it. The pure polyester powder coating (oven baked) done on the pipes extend the life of equipments And install by C.C. base system as per order by engineer in charge Age capacity 6-12 Year. |
| 16 | Providing and installation of Orbit Climber:- Safe Play Area -3.4 mtr. X 2.2 mtr. Dia Area: - 2.4 mtr. 1.2 mtr.Height- 2.4 mtr.It required area 2.4 mtr x 1.2 mtr& height 2.4 mtr and leg support should made up of 50 mm IDGI pipe outer frame should be made by 32 mm IDGI pipe in main frame joint with 20 mm IDGI pipe in handrails/inner frame in dia. Ladder should be made by 20 mm IDGI pipe. And connected with proper fitment like welding, fastener.All the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. The pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. The pure polyester powder coating (oven baked) done on the pipes extend the life of equipments.And install by C.C. base system as per order by engineer in charge Age capacity 6-12 Year. |
| 17 | Providing and installation of Circular swing :- Safe play area:-2.5 m x 3 mThe area :-1.5 m x 2 mThe leg support of this item is made up of 40 MM, while the top bar is from 50 MM powder coated GI pipes. The swing frame is made from 25 MM and 15 MM powder coated GI pipes. There are two seats provided which are made out of Fiber Reinforced Plastic. The platform is made using chequered plate for footrest and bearing assembly is made. All the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. The pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. Slide should be made in a single mould piece there is no any joint in the slide.FRP components should be paint by 3 layers of PU paint. And install by C.C. base system as per order by engineer in charge. All the sharp edges and corner properly grinded to give smooth finishing so that children are not hurt with playing on it. The pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. And install by C.C. base system as per order by engineer in charge Age capacity 3-10 Year. |
| 18 | Providing and installation of Platform (GI platform) Marry Go Round having Product area 5.0 m Product height 1.1 m Safe paly area 2.5 mtswith age limit 5-12 year |
