|
| 1 | Sub Heading 1 |
| 2 | Surface dressing of ground include removable ofDust,vegetation and inequalities not exceeding 15cm depth and disposal of rubbish, lead upto 50m andlift upto1.5m.Total Area = (66’1’x13’0”)+(59’3”x7’9”)+(32’5’’x19’11”)=1963.82sft=~182.51sqm. |
| 3 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate.(1)With providing improper slope.Area of shed-5=66’1”x13’=859.04sftArea of shed -6=59’3”|x7’9”=459.19sft.(2)With Patchy FlooringArea of shed-2&3=645.6sqftTotal area for shed 5&6=1963.82sft=~182.51sqm |
| 4 | Surface dressing of ground include removable of Vegetation and inequalities not exceeding 15cm depth and disposal of rubbish, lead upto 50m andlift upto1.5m.Total Area = 15’x57’=855sft=~79.46sqm. |
| 5 | Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m. Ordinary rock. Total = (10”x10”x2’)x7no.s=9.64cft=~0.27cum |
| 6 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)Total =(10”x10”x2’)x7no.s=9.64cft=~0.27cum |
| 7 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type2”&1”pipesTotalweight=(8’+2’)x6no.s+(8’6”+2’)x1+(13’3”x7no.s)=153.25=49.7m=253+5%=265kg |
| 8 | Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. Total= 8’1”x6no.=48.48’=14.74mx2.6kg/m=38.32kg |
| 9 | Providing and fixing precoatedgalvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. Total=13’3”x55’=728.75sft=~67.28sqm |
| 10 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturersspecificationsPainting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufactureTotal area=35.79sqm=~36sqm |
| 11 | Goods and Service Tax @ 18% |
