|
| 1 | Removing plantation and its roots from buildings at all height, including dismantling and repairing plaster and masonry including repair of surface with cemnet plaster 1:3 ( cement :3 sand) after applying chemical with name \"ROUND UP\" or equivilatant on the leaves of plants all complete as per the direction of the Engineer-in-charge . |
| 2 | Note 1. The rate includes cost of chemical, arrangement of necessary ladders upto required height & repair work if any. |
| 3 | 2. scaffolding if required at any site shall be used only with the prior approval of the Engineer-in Charge and shall be paid for separately). |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 5 | 1:2:4 (1 cement : 2 coarse sand(zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 6 | 1:5:10 (1 cement : 5 coarse sand(zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 7 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: |
| 8 | Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 9 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 10 | Deduct for not providing hinges in doors, windows or clerestory window shutters with : |
| 11 | Stainless steel butt hinges with stainless steel screws : |
| 12 | For 2nd class teak wood and other class of wood shutters. |
| 13 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: |
| 14 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 15 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : |
| 16 | 30 mm thick shutters |
| 17 | with ISI marked M.S. pressed butt hinges bright finished of required size - Kiln seasoned and chemically treated hollock wood |
| 18 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : |
| 19 | 250x16 mm |
| 20 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : |
| 21 | 200x10 mm |
| 22 | 100x10 mm |
| 23 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : |
| 24 | 100 mm |
| 25 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 26 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 27 | Twin rubber stopper |
| 28 | Providing and fixing to existing door frames. |
| 29 | 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in-charge. |
| 30 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 31 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. |
| 32 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc.,., complete. |
| 33 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 34 | Two or more coats on new work. |
| 35 | Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. |
| 36 | One coat. |
| 37 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : |
| 38 | One or more coats on old work. |
| 39 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground , all complete as per directions of Engineer-In-Charge. |
| 40 | With cement mortar 1:4 (1cement: 4 coarse sand). |
| 41 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: |
| 42 | Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm). |
| 43 | Cleaning of terrace/loft water storage tank (inside surface area) upto 2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of tank, including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba, all complete as per direction of Engineer-in-Charge. (The old date already written on tank should be removed with paint remover or black paint and if date is not written with the stencil or old date is not removed deduction will be made @ Rs. 0.10 per litre if during cleaning any GI fittings or ball cock is damaged that is to be repaired by contractor at his own cost and nothing extra will be paid on this account) |
| 44 | Cleaning and de-silting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer-in-charge. |
| 45 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in- Charge. |
| 46 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 47 | Providing & Fixing Galvanizd MS wire mesh of apeture 1.4 mm with nominal dia of 0.63mm to wooden /steel doors & windows with necessary screw nails beading or welding after removing existing wire mesh (if any), all complete as per the direction of Engineer-in- charge. |
| 48 | Cleaning of whole BSNL Compound including out side area near compound wall & entrance gate, removing of grass, bushes and cleaning of internal drains, roads & approach roads, collection of malba and garbage all complete as per direction of Engineer-in-Charge. (Note: The cost of alll necessary tools/plants/machine required for cleaning job is inclusive in the item & shall be provided by the agency) |
| 49 | Staff quarter and T.E Compound at Dheerwali, Haridwar |
| 50 | T.E Compound at Mayapur Haridwar. |
| 51 | IQ and T.E Compound at Bhimgoda, Haridwar |
| 52 | T.E Compound, Jwalapur, Haridwar. |
| 53 | Store and Type-V compound at Shyamlok, Haridwar |
| 54 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 55 | Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) |
| 56 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 57 | Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer in-charge. |
| 58 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead: |
| 59 | Of area 3 sq. metres and below |
| 60 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 61 | Credit for dismantled unserviceable material |
| 62 | Wooden paneled / flush door shutter/ glazed shutter/ wire guage shutter of size upto 2.50 Sqm. |
| 63 | Brass fittings such as water taps , pillar cock , angle cock, stop cock and door window brass fittins or alike . |
| 64 | PVC Cistern |
| 65 | PVC Tanks (upto 500 Litre Capacity) |
| 66 | Old dismantled reinforcement bars/ steel sections /steel-built up sectioins etc |
| 67 | Supplying of following Sanitary items of approved make to be used at site all complete as per direction of Engineer-in-charge. :- |
| 68 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests with necessary grit , sand and cement for fixing of WC seat |
| 69 | White vitreous china pedestal type water closet (European type W.C. pan) of approved qualitywith necessary grit , sand and cement for fixing of WC seat |
| 70 | PVC Flushing Cistern 10 lts capacity ( low level) with fittings, accessories and flush pipe. |
| 71 | ISI marked solid plastic Seat cover with lid with CP brass hinges and rubber buffers for European type WC pan |
| 72 | White Vitreous China Wash basin size 550x400 mm of approved quality |
| 73 | ISI marked Stainless steel kitchen sink - without drain board 610x510mm bowl depth 200 mm |
| 74 | 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate for European WC seat |
| 75 | Flexible (coil shaped) PVC waste pipe for sink and wash basin 32 mm dia / 40 mm dia with length not less than 700 mm i/c PVC waste fittings |
| 76 | 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws |
| 77 | PTMT Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms |
| 78 | ISI marked uPVC pipe 75 mm dia |
| 79 | ISI marked uPVC pipe 110 mm dia |
| 80 | ISI marked uPVC coupler 75 mm dia |
| 81 | ISI marked uPVC plain bend 75 mm dia 87.5 degree |
| 82 | ISI marked uPVC plain bend 110 mm dia 87.5 degree |
| 83 | ISI marked uPVC TEE 75 x75x75 mm dia |
| 84 | ISI marked uPVC equal TEE 110 x 110 x 110 mm dia |
| 85 | Flush pipe ( PVC Cistern long bend) of approved quality |
| 86 | Washer for PVC cistern of approved quality |
| 87 | Syphon Assembly for PVC cistern |
| 88 | ISI marked uPVC Floor trap / nahani trap 100x 75 mm size |
| 89 | Supplying of following water supply items of approved make to be used at site all complete as per direction of Engineer-in-charge. :- |
| 90 | Chlorinated Polyvinyl - chloride (CPVC) pipe with necessary fittings including ( Note :- Length of CPVC pipe used for maintenance work / repair work shall only be measured and nothing extra for CPVC fittings shall be paid) |
| 91 | Chlorinated Polyvinyl - chloride (CPVC) pipe 20 mm dia |
| 92 | Chlorinated Polyvinyl - chloride (CPVC) pipe 25 mm dia |
| 93 | C.P. brass bib cock 15 mm nominal bore confirming to IS:8931 |
| 94 | C.P. brass angle valve 15 mm nominal bore confirming to IS:8931 |
| 95 | Uplasticised PVC connection pipe with brass unions 45 cm long 15 mm nominal bore |
| 96 | G.I. Union for G.I. pipe 15 mm nominal bore |
| 97 | G.I. Union for G.I. pipe 20 mm nominal bore |
| 98 | PTMT Bib cock 15 mm nominal bore 86 mm long and weight not less than 88 gms |
| 99 | PTMT pillar cock 15 mm nominal bore , 107 mm long and weighing not less than 110 gms. |
| 100 | PTMT angle stop cock 15 mm nominal bore, weighing not less than 85 gms |
| 101 | PTMT Ball cock 15 mm nominal bore, 105 mm long, weighing not less than 138 gms |
| 102 | PTMT Ball cock 20 mm nominal bore, 105 mm long, weighing not less than 138 gms |
| 103 | Brass metal spindle for bib cocks / stop cock / angle valves and aloke of approved quality |
| 104 | PVC over head water stoarge tank cover |
| 105 | Brass full way valve / gate with C.I. wheel (screwed end) 15 mm dia |
| 106 | Brass full way valve / gate with C.I. wheel (screwed end) 20 mm dia |
| 107 | Polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement |
| 108 | G.I. pipeswith necessary GI fittingsinncludingWhite lead, hemp, oil , Cement, sand and grit etc.except GI Union( Note :- Length of GI pipe used for maintenance work / repair workshall only be measured and nothing extra for GI fittings shall be paid) |
| 109 | i) 15mm nominal bore |
| 110 | ii) 20 mm nominal bore |
| 111 | Arranging services of plumber for plumbing jobs ( sanitary work , water supply & drainage work etc ) including necessary labour whereever required for day to day maintenance of all departmental buildings including repair/fixing of all sanitary & water supply items including fixing of new sanitary and water suplly fittigs ,opening of air locks from water supply pipe all complete as per direction of Engineer-in-Charge. |
| 112 | Note 1. All T&P shall be arranged by the agency except materials required which will be paid for separately. |
| 113 | 2. Payments shall be made on job basis for period of one month). |
| 114 | Providing Mannual assistance for miscellaneous works as per site requirement and as per direction of Engineer-in-Charge. |
| 115 | (Note: One Man day shall be treated as One job) |
| 116 | Cleaning of manhole chamber including inter connected chocked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines all complete as per the direction of Engineer-in-charge.(Note:- Rate includes the cost of Cleaning of manholes sewer line i/c dewatering, removal of manhole cover and keeping the same back in position after completion of job.) |
| 117 | Removing of chokage of floor traps, Nahani traps and alike including attached pipe and bends for smooth flow of waste water by pressure pushing, flexible wire and taking out refuse and dispose off etc. complete as per the direction of the Engineer-in-charge. |
| 118 | Removal of chockage / blockege in W.C. Seat including cleaning of seat & disposal of waste material all complete as per direction of Engineer-in-Charge. |
| 119 | Providing Reams of A4 Size Photocopy paper of weight not less than 70GSM of ISI make to be used for maintaining day to day maintenance records in ofice and as approved by engineer-in-charge. (1 Ream=500 Sheets) |
| 120 | Refilling of Printers Cartrdige of make M1136MFP to be used for maintaining day to day maintenance records of Sub-Division office of aprroved make and as approved by engineer-in-charge. |
