|
| 1 | Excavating in trenches, in any typesoilnot exc 1.5m wide and not exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sq. m on plan and not exc 1.5m in depth and getting out complete all as specified and directed. |
| 2 | Excavating over areas, n exc 1.5 m deep and getting out in any type of soil complete as specified and directed. |
| 3 | Returning filling in including spreeding, leveling, watering and well ramming in layers n. exc 25 cm thick in soft /loose soil complete all as specified and directed. |
| 4 | Removal of excavated soil exc 500m not exc 1Km and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed. |
| 5 | Material & labour for sand filling with clean dry find sand unwashed including gently punning around cables in trenches/ducts for cable protection complete all as specified and directed. |
| 6 | M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base, foundation, filling, mass concrete complete all as specified and directed. |
| 7 | M&L for cement concrete(1:2:4) type B-1 using 20 mm graded crushed stone aggregate as in lintels upto 1.5 clear span , cills steps seismic and other similar bands, copings, hold fast and the likeincluingweathering , slightly rounded or chamfered anglesand throatingasdirected with and icludingnecessary form work in CM 1:4 completeall as specified an directed. |
| 8 | M&L for RCC M-25 design mix using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers, lintles over 1.5 m span complete all as specified and directed. |
| 9 | M&L for RCC M-25 design mix using 20 mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. |
| 10 | M&L for RCC M-25 design mix using 20 mm graded stone aggregate as in Columns, pillars, piers, posts and struts complete all as specified and directed. |
| 11 | M&L for RCC M-25 design mix using 20 mm graded stone aggregateas in roof slab, shelves and the like complete all as specified and directed. |
| 12 | M&L for Plain cement concrete 1:2:4 type -B2 (using40mm graded crushed stone aggregateas in foundation filling & mass concrete , sub base complete all as specified and directed. |
| 13 | M&L for PCC 1:3:6, type C-2 (using 40mm graded stone aggregate) as in surfacechannel and drain incluing necessary form work complete all as specified and directed. |
| 14 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed. |
| 15 | Supply only Liquid water proofing compound ISI Marked (used 200 ml per bag of cement) complete all as specified and directed. |
| 16 | M&L for brick work with subclass \"B\" bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed. |
| 17 | M&L for Cutting chases, pinningin making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills sunshades, shelves lintels etc and cutting chases for concealed water pipe etc and making good cutting not exc 10cm. complete all as specified and directed. |
| 18 | M & L for 18mm thick Granite stone slab (of any type/Colour ) Slabs machine cut in skirting/dado/ cill and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including rounding to edges cutting and polishingover and including 10mm thick cement mortar 1:4 , on fair faces of brick work or concrete surfaces as backing for Granite stone slab complete all as speifide & directed |
| 19 | M & L for use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. |
| 20 | M&L for use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed. |
| 21 | M&L for Use and waste of formwork as in foundation, footings, padestals and in PBs complete complete all as specified and directed. |
| 22 | M&L for Use and waste of formwork as in Columns complete all as specified and directed. |
| 23 | Taking down chowkhats with shutters (without taking off shutters from frame) not exc. 1.50 sqm each complete all as specified and directed. |
| 24 | Taking down chowkats or frame of any description exc 1.5 Sqm each and n.exc 4.0 Sqm (without taking off shutters from the frames) & remove off the premisescomplete all as specified and directed. |
| 25 | S&F solid PVC door frame of size 50mmx 47mm made out of 5 mm plain/wall nut colour PVC sheet reinforced with MS square tube as per specification & drawingsspecified in SSR Part-II 2010 complete all as specified and directed. |
| 26 | S&F Factory Made Solid PVC Moulded Door Shutter wall nut colour, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawingcomplete all as specified and directed. |
| 27 | S&F first class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed. |
| 28 | S&F 40 mm thick firstclass hard woodplain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers,etc are provided with stiles and rails as specified in SSR Pt I Section 8, clause 8.24 (a) complete all as specified and as directed. |
| 29 | S&F 18 to 20 mm thick solid PVC Board for cupboard/cabinet shutters with one side 1 mm thick printed PVC sheet other side plain PVC sheet of approved pattern as per specification and drawing and including necessary beading in matching colour, magnetic ball catcher, 1 brass 2 lever lock of 50 mm size complete all as specified and directed. |
| 30 | S&F aluminium anodised barrel tower bolt of extruded section 150 mm long and fixed complete all as specified and directed. |
| 31 | S&F aluminium anodised barrel tower bolt of extruded section 125 mm long and fixed complete all as specified and directed. |
| 32 | S&F 100 mm sizemild steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws/welded to frame complete all as specified and directed. |
| 33 | S&F 100 mm sizemild steel butt hinges, ISI marked, heavy weight, cold rolled and fixed with screws/welded to frame complete all as specified and directed. |
| 34 | S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed allas specified and directed. |
| 35 | S&Faluminium die cast body door closer hydrau lically regulated, designation No. 3, universal type, suitable for door shutters of upto1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed. |
| 36 | S&F in repair, magnetic ball catcher, size complete all as specified and directed. |
| 37 | S&Fbrasshandles, cast type, anodised 100 mm size completeall as specified and directed. |
| 38 | S&F in repairs mortice lock, vertical type of size 100 mmwith brass body 2 lever complete all as specified. |
| 39 | S&Fbrasshandles,, cast type, anodised 150 mm size completeall as specified and directed. |
| 40 | S&F continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flap (when open) 30 mm completeall as specified and directed. |
| 41 | S&F wire netting of galvanised steel wire size of mesh 20 mm and nominal dia of wire 1.40 mm completeall as specified and directed. |
| 42 | S&F 125 mm long hasp & staple safty type aluminium anodisedwith mild steel hinge pinincluding bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 43 | M & L for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips qualitycomplete all as specified and directed. |
| 44 | M&L for Mild steel bars TMT Bars 5mm dia & over upto & including 10mm dia in stirrups, spacers & binders, cut to length, bent to shape required, including cranking, bending , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips Complete all as Specified and directed. |
| 45 | S&F galvanised 2 strand steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of fencing posts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins etc complete all as specified and as directed. |
| 46 | S&F concertina coil 2.5 mm dia of core wire in 450 mm circular dia of each coil having a core wire of high carbon spring steel of high tensile strength as per grade of IS-1454(Part-I) with low carbon steel strip punched tape of 19 mm wide, 0.50 mm thick and series of knife edge sharp barb/blades @ 25 mm centre to centre punched all along the length of both sides of strip at regular interval conforming to IS-513 complete all as specified and directed. Note:- Concertina coil having 50 Rounds per 6 RM. |
| 47 | S &F M.S Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165complete all as specified and directed. |
| 48 | S&F mild steel angle iron in fencing posts, and struts fixed independently without connecting plates, grill etc and cutting to required size and shape, conforming to gde Fe 410-W (Gde E-250) Quality complete all as specified and directed. |
| 49 | S&F Powder Coated aluminiumwindow and ventilator shutters side hung type without sash bars, , aluminiumsectionweighing not less then 0.55kg/m includingnecessary jointing cleats/ glazing clips,rubber neoprene packing, anodised aluminium snap beading , screws, anodised aluminium fittings such as peg stay 150mm long (1 No) hinges typeB-21 100mm long ((2 Nos) suitable handle (1 No) complete all as specified and directed. |
| 50 | Preparing RCC roof slab top by wire brushingand cleaning thedust and forign materail etc completeand applying a coat of hot blown bitumen 85/25 grade @ 1.20kg/Sqm over a coat of bitumen primer @ 0.40 ltrs/Sqm and there after laying of a layer of APP based polymeric membrane (five layered with centre core as 100 microns high molecular high density polyethylene film)weighing 3kg/Sqm andwill be laid as per MES SSR Pt-I para 11.43.2.2 with minium side lap 75 mm and end Lap of 150 mm bonded with hot blown bitumen 85/25 gde penetration @ 1.20kg/sqm and blinded with fine sand in dry condition (pleable free) @ 0.50 kg/sqm dusted over the bitumen coatcomplete all as sp[ecified and directed. |
| 51 | M&L for glazed coloured ceramic tiles, first quality (or approved class, colour and design/shade) of size 350x250x7mm/ 450x350x7mm thick in vertical surfaces, as in dado/skirting etc set & jointed in neat cement slurry & pointed in coloured cement to match with coloured tiles, over and including 10mm thick rendering in cement mortar 1:4 rough finish to receive the tiles complete all as specified and directed. |
| 52 | M&L for non skid Ceramic tiles,first quality( of approved class , colourand design/ shade )6 to 7 mm thick( square/ rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm,,as in floorsurfaceetc set and jointed in neatcement slurry and pointed in coloured cement to match with coloured tiles overand including 15 mm Screed bed in CM 1: 6 complete all as specified and directed. |
| 53 | M & L 40 mm thick PCC (1:2:4) type B-0, (using 12.5 mm graded crushed stone aggregate) in two layers (each 20 mm) with chicken mesh provided between the layers and finished even and smooth with false grooves @ 450x450 mm complete all as specified and as directed.( Note: Chicken wire mesh shall be measured and paid separately under respective item of sch \"A\"). |
| 54 | M&L providing 100mm thick PCC (cement concrete) 1:2:4 etc type C-2 (using20 mm graded stone aggregate) pavement/ramp/floor finsihed fair and event complete all as specified and directed. |
| 55 | M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour glossy finish, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed. |
| 56 | M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and smooth (without using extracement) complete all as specified and directed. |
| 57 | M&L for Rendering 15 mm thick on fair faces of concrete/brick surfaces in cement mortar 1:4mixed withwater proofing compound as per manufacturer\"s instruction, finished fair and even without using extracement complete all as specified and directed. Note :- WPC shall be measured and paid forseprately as supply only under respective item of sch A/BOQ. |
| 58 | M&L 10mm thick cement plaster on fair face ofconcrete surface including repair of doubing roof surfacesin CM 1:3 finished even land smooth without using extra cement over complete all as specified and directed.(Water proofing compound shall be measured and paid sepratly ) |
| 59 | Taking down existing cement or cement lime plaster/Grit wash of any description and in any position on brick or concrete surfaces etc including racking out joints, hacking for key scrubbing down with water etc complete all as specifed and directed. |
| 60 | M&L for taking down/dismantling of existing roof treatment / cement plaster of any description such as PCC Padding/ Coba treatment/ mud phuska/Lime conc terracing including screed bed etc. Hessian base felt/tar feltetc. (any type and thickness) with and including, removing debris out sideMOD Land at contractor is own arrangement )complete all as specified & directed. |
| 61 | M & L forpreparing new plasteredsurface of walls and applying two coat of Oil Bound Distemper over and including a coat of alkaliresistantprimer over 3mm thick damproof wall care putty in two layer complete all as specified and directed. |
| 62 | M&L for applying Two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade ( Company Depot Tinted) with silicon additives @ 1.43 litre / 10 Sqm over and including priming coat of exterior primer applied and 0.90 litre/10sqm over new surfaces external surfaces of wall complete all as specified and directed. |
| 63 | Preparation of new plastered surfaces of walls and concrete work and applying two coats of cement based paint complete all as specified and directed. |
| 64 | M&L for 4.80 mm thick sheet glass ordinary quality in panesexc 0.50 sqm each pane fixed with & including rubber gasket in aluminium frame work complete all as specified and directed. |
| 65 | M & Lpreparation of new orpreviously untreatedy steel surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 66 | M&L for preparation of new or previously untreated wooden surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed |
| 67 | S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet,integral foot rest (excluding flushing cistern and flush pipe) & including CI trap & connecting fitting as required set inplain cement concrete (1:3:6) type C-1and connecting to flusing cistern and trap & connecting fittings as required and making good to floor as per existing with and including removing unserviceable water closet outside MOD land complete all as specified and directed. |
| 68 | S&F in repair white vitreous China wash down water closet pan (pedestal) pattern, and trap(excluding fixing bolts, flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. with and including plastic water closet sheet covers white closed pattern with flat bottom, with mild steel chromium plated or aluminised hinging device and 15mm dia chromium plated brass washing jet fixed to water closet with 15mm dia and 1.2m to 1.5m long flexible pipe with chromium plated spring type cover with and including removing unserviceable water closet outside MOD land complete with fixing arrangement fancy look complete all as specified and directed. |
| 69 | S&F in repair PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic actiontype with inlet ball valve and float, handle with & including bracket andPVC flush pipe 32 mm borecomplete all as specified and directed. |
| 70 | S&F counter top wash hand basin coloured oval type 550x445 mm fixed over granite slab ofAppropriatesize including brackets, PVC connection waste pipe waste coupling etccomplete all as specified and directed.Make: Parryware cat No: C 0431 popular for counter type and bolan code no 9901 / 9811 or equivalent in Jaquar/Hindware as approved by GE. Note Graniteslabwill bemeasuredand paidseparately |
| 71 | S&F in repairs vitreous china urinals, flat back of size 465mmx355mmx265 mm, white minimum incl grating and union for discharge pipe complete incl providing & fixingplugs, bedding urinal against wall in cement mortar 1:2, securing urinals plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete all as specified and as directed. |
| 72 | M & L for 20mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors with and including taking down existing old pipe complete all as specified and directed. |
| 73 | M & L for 15mm bore `Medium grade` GI tubing with all fitting and fixed complete to walls and ceilings or laid in floors with and including taking down existing old pipecomplete all as specified and directed. |
| 74 | S&F fancy type Pillar cock Hot and Cold mixer with base flange complete all as specified and as directed.Make : Jaquar Cat No. KUB 35001F or equivalent in Parryware/Hindware as approved by GE. |
| 75 | S&F PVC connection 450 mm long suitable for 15 mm GI pipe with two brass nuts & rubber washers complete all as specified and directed. |
| 76 | S&F 2 WayBib tap, cast copper alloy fancy type suitable for 15 mm dia pipes complete all as specified and as directed.Make :Jaquar Cat No KUB-35041F or equivalent in Parryware/Hindware as approved by GE. |
| 77 | S&F hand shower (health faucet) ABS body with 8 mm dia,1 mtr long flexible tube &wall hook complete all as specified and as directed.Make : Jquar Cat No. ALD-CHR-593N or equivalent in Parryware/Hindware as approved by GE. |
| 78 | S&F towel ring square complete all as specified and as directed.Make : Jaquar Cat No. AKP-35721P or equivalent in Parryware/Hindware as approved by GE. |
| 79 | S&F stainless steel toilet roll holder with flap complete all as specified and as directed. Make : Jaquar Cat No. AKP-35753P or equivalent in Parryware/Hindware as approved by GE. |
| 80 | S&F Corner glass shelf complete all as specified and as directed.Make : Jaquar Cat No ACN-1173 or equivalent in Parryware/Hindware as approved by GE. |
| 81 | S&F single towel rail 600mm long complete all as specified and as directed. Make : Jaquar Cat No. AKP-35711P or equivalent in Parryware/Hindware as approved by GE. |
| 82 | S & F Soap dispensor with glass bottle complete all as specified and as directed.Make : Jaquar Cat No. AKP-35735P or equivalent in Parryware/Hindware as approved by GE. |
| 83 | S&F PVC (SWR) pipe 110mm bore single socketed in any length with rubber ring jounts laid in trenches or in floor.complete all as specified and directed. |
| 84 | S&F in repair PVC (SWR) bends any radius, with access door, for 110 mm bore of pipe complete all asspecified and directed. |
| 85 | S & F PVC (SWR) gully trap 125/110 mm, settingand jointing with solvent cement. |
| 86 | S&F in repair CP unirnal Push Cock incl necessary fittings complete all as specified and directed |
| 87 | S&F in repair CP Urinal Spreaderincl necessary fittings complete all as specified and directed |
| 88 | S&F in repair for 600x450mm beveled edge looking mirror of selected quality glass 4 mm thick mounted on 6mm thick AC building board or commercial ply woodand fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified & directed. |
| 89 | S&F rotational moulded polythene water storage tank 1000 Ltr capacity (Cylindrical vertical with closed top) hosted with and including 20mm dia ball brass valves, high pressure with polythene, float and fly nut complete screwed for iron pipe of for brass ferrute and fixed in position all as per SSR part I complete all as specified and directed. |
| 90 | Providing and laying non-pressure NP2 class (light duty) 300 mm diaR.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete all as specified and directed. |
| 91 | Dismantling wrought iron or mild steel work of any description not otherwise described and removal of dismantling materials with and including, removing debris outside MOD Land at contractor is own arrangement , complete all as specified and directed. |
| 92 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing with and including, removing debris outside MOD Land at contractor is own arrangementdebrish and rubbish off the premises and stacking serviceable tiles complete all as specified and directed. |
| 93 | Demolition of cement concrete (unreinforced) of any description as in ground floors and pavings not exceeding 15cm thickness (above or below ground floors) with and including, removing debris outside MOD Land at contractor is own arrangement complete all as specified and directed |
| 94 | Demolition of brick or stone boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone works and precast concrete articles with and including, removing debris outside MOD Land at contractor is own arrangement complete all as specified and directed. |
| 95 | Demolition of ( reinforced cement concrete) (reinforcement cut as required to facilitiate demolition)of any description and in any positionnot otherwise specifically provided with and including, removing debris outside MOD Land at contractor is own arrangement complete all as specified and directed. |
| 96 | Taking down Cast iron/PVC pipe of any dia and size fixed on wall or floor including all fittings with and including, removing debris outside MOD Land at contractor is own arrangement complete all as specified and directed. |
| 97 | Dismantling barbed wirefixing to any type of fencing posts,and removal of dismantling materials to a distance exceeding 500 M but not exceeding 1000mtr complete all as specified and directed. |
| 98 | Dismantling posts or struts (wood, steel, or RCC) any section, including taking out embedded portion in concrete, brick work, masonry etc with and including and removing of debris outside MOD Land at contractor is own arrangement complete all as specified and directed. |
| 99 | Dismantling fencing wire mesh of any type complete all as specified and directed. |
| 100 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed, |
| 101 | M&L for point wiring with single corePVC insulated unsheathed 1100 volt grade FRLS-IS 694 cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI markednot less than 20mm dia, concealed conduit wiring in walls and surface with GI saddles, GI screws, rawl plugs in ceiling or roof if not possibleincluding Tee, Junction boxes and provision ofmodular flush metal boxes, modular inner and outer plate suitable formodular switch, socket and fan regulator as per site requirement and drawing continuous earth wire with and including PVC insulated unsheathed 1100 Volts grade FRLS-IS 694 cable with multi strandedcopper conductor of size 1.5 Sq mm (Nominal area) and connected to main earth dolly complete all as specified and directed for one light/fan point controlled by one Switch. |
| 102 | S&FModular switch single pole one way 6 amp ISI marked ccomplete as specified and as directed. |
| 103 | S&F 3 pin 5 Amp ceiling rose made of polycarbonate, isolated body including connecting with the junction box complete all as specified and directed. |
| 104 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed |
| 105 | Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete alll as specified and directed |
| 106 | Supply and fix exhaust fan, steel body AC single Phase 230V of size 300m sweep with, blades, and frame and louvers all as specified and directed by Engr-in-Charge. Make : Havells/ Bajaj or equivalent |
| 107 | Taking down/disconnecting the existing LT cable of any type and any size from boundary wall/trench and Re-laying LT cable Obtained form (Any size) complete all as specified and directed . |
| 108 | Taking up CI/DI water pipes including all fittings of any sizewith spigot and socket ends and lead joints and R e-laying CI/DI water pipes including all fittings of any size complete all as specified and directed . |
| 109 | Fixing / laying only old PCC cable coverof any description as obtained from dismantling of the cable complete all as specified and directed. |
| 110 | Supplying, Fixing, jointing and testing for provision of straight through joints,complete withjointing materials and accessories , suitable for XLPE, LT Cable, 1100 Volts grade, for the following sizes of cablescomplete all as specified and directed. |
| 111 | 25 Sqmm to 50 sqmm 3½ core |
| 112 | 70 Sqmm to95 sqmm 3½ core |
| 113 | 120 Sqmm to 150 sqmm 3½ core |
