|
| 1 | Material and labour for seamless plaster of paris false ceiling comprising of Gl frame work with Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including necessary hangers 6mm dia GI adjustable strip suspenders up to 1200mm long fixed to roof slab(using concrete drill) by suitable GI fasten with and including panel for ceiling (12mm thick Plaster of Paris board seamless 1200mmx1800mm size) with self-tapping screw finishing covering the joints with fiber tape and ceiling compound 48 mm wide fibre tape to provide seam less finish and surface finish as specified (particular specification 22.2 ) completely all as specified and as directed.Note: The rate is inclusive of frame work, POP panel and surface finish nothing extra shall be paid on this account |
| 2 | Demolition of brick or stone PCC block masonry built in cement mortar or cement lime mortar including all quoins,arches,pillers etc but excluding ashlar facings,dressed stone work and precast concrete articles in any position complete all as specified and as directed. |
| 3 | Material and labour for precastPCC 1:3:6 Type C1 using 20 mm graded aggregate solid block masonryexceeding 10 Cm width(with plain or interlocking joints as directed), built in cement mortar 1:6 all as specified and as directed. |
| 4 | Material and labour for precastPCC 1:3:6 using 16 mm graded aggregate solid block masonrynot exceeding 10 Cm width(with plain or interlocking joints as directed), built in cement mortar 1:6 all as specified and as directed. |
| 5 | Taking down cement plastering on concrete or Brick works surface racking out joints, hacking for key , scrubbing down with water etc complete all as specified and as directed. |
| 6 | Material and labour for rendering 15 mm on fair faces of brick or concrete surfaces in CM 1:6, finished even and fair without using extra cement complete all as specified and directed. |
| 7 | Material and labour for rendering 15 mm on fair faces of brick or concrete surfaces in CM 1:4, finished even and fair without using extra cement complete all as specified and directed. |
| 8 | Material and Labour for preparing of new surfaces of any description and applying two coats of acrylic distemper, white or tinted over a coat of primer after applying one or more coat of wall putty to achieve smooth surfaces on plastered wall surface complete all as specified and as directed. |
| 9 | Material and labour for preparation of old distempered wall surfaces by washing, rubbing down and stopping the surfaces and applying Two coat ofacrylic distemper applied to walls, complete all as specified and directed |
| 10 | Material and labour for Preparation ofold ceiling surfacesincluding washing, rubbing down and stopping by brooming down, scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat ofacrylic distemper on ceiling surfaces complete all as specified. |
| 11 | Material and labour for preparation of new surfaces on wall and applying two coat of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, alkali and fungal resistant, dirt resistant exterior paint of required shade(company depot tinted) with silicon additives @ 1.43 Litre/10 Sqm over and includingpriming coat of exterior primer applied @ 0.90 Litre per 10 Sqmover new surface complete all as specified and as directed. |
| 12 | Taking down chokhats or frame not exceeding 1.5 sqm each with shutters (without taking off shutters from the frame ) complete all as specified and directed. |
| 13 | Taking down chowkats or frame exc 1.50 sqm each but not exc 4 sqm each with shutters (without taking off shutters from the frame ) complete all as specified and directed. |
| 14 | Providing and fixing Powder coated Aluminium work for doors and Partitions walls with extruded built up standard tubular sections/ appropriate & sections and other sections of approved make fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners for fixing of vertical sections in the ceiling to support the frame including necessary filling up of gaps at junctions, top, bottom and sides with required PVC/ neoprene felt, etc. Aluminium sections shall be smooth, rust free straight, metered and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass/ stainless steel screws all complete the direction of engineer-in-charge With powder coated aluminium frame section ofsize 100mm X68.5mm X 2.5 mm thick and shutter sections of size 100 mm X 38.10 mm X 2.5 mm thick ( sectional weight of the Aluminium section should not be less than 4 Kg. for the sectional length of 15) with 12 mm thick both side pre-laminated flat pressed three layer of graded wood particle board conforming to IS: 12823 grade I type II in panelling of partition walls or with float glass panes of 5 mm thickness ( Modi, saint Gobain or equivalent) panelling of required height complete in all respect including all hardware fittings as per the direction of Engineer -in charge |
| 15 | Supply and fix Aluminium Powder coated sliding window/ventilator shutter using aluminium section weighing 0.55kg/m, 20mm thick using standard vertical handle section, interlocking section, top and bottom rails, U channels for all -around for gauge shutters. All sections are of medium weight series of approved makein three track sliding window in whichtwo shuttersof with and including of 4mm thick Modi guard or equivalent float glass and one shutter fixed with inclusive ofstainless steel wire mesh of size 0.30mm nominal dia and average with of aperture 1.40mm, including necessary jointing cleats, glazing clips , good quality bearing rollers, Neoprene rubber Gasket and rubber beadingof any type, screws , aluminium fitting such as Gasket, handle (01 Nos on each shutter), interlocking arrangements complete all as specified and asdirected by Engr in Charge. Note: The quoted rate shall be inclusive of 4mm thickfloat glass and Stainless steel wire cloth. |
| 16 | Material and Labour for pre-laminated particle board 9 mm thick, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws in timber frame work complete all as specified and directed. |
| 17 | Supply and fix lnsulated PVC Wall Lining consisting of PVC Insulated Panels (25mm thick insulated PVC wall lining) having expanded polystyrene (EPS) stuck to 2mm thick plain colour PVC sheet duly fitted into the wall of any shape and any colourat any position Each panel have to interlock with each other complet all as per manufactures instruction complete all as specified and asdirected by Engineer in Charge. |
| 18 | Material and Labour for 20mm thick Granite ( of any type) work (table rubbed and polished) as in wall lining(veneering to wall) and the like and fixedover and including 15mm thick cement mortar 1:3 including pointing in white cement using marble dust in 1:2 with admixture of pigment to match with shade of granite complete all as specified and directed. |
| 19 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) remaining serviceable tiles to stores and rubish off the premises all as specified and as directed. |
| 20 | Material and labour for providing 25mm thick plain cement concrete 1:2:4 mix type B1, using 20mm graded stone aggregate as in under layer to flooringfinished rough to reiceve toping complete all as specified and as directed. |
| 21 | Material and Labour for non-skid coloured Ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11sqm but not excceding 0.18 sqm, in floors etc, set and jointed in cement mortar and pointed in white of coloured cement to match over and including 15 mm thick screed bed in CM 1:4 complete all as specified and as directed. |
| 22 | Material and Labour for glossy finish coloured vitrified ceramic tiles 8-10 mm thick, area of each tiles exceeding 0.42sqm but not exceeding 1.0sqm, of any pattern (pattern consists combination of two or more tiles ) as on floor surfaces etcjointed in neat cement slurry and pointed in colored cement to match colour tiles over and including 15mm thick screed bed in CM 1:4 and pointed in coloured cement to match coloured tiles complete all as specified and as directed. |
| 23 | Material and labour for ceramic coloured tiles in vertical surface 600x100/150 mm size of 8 to 10 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles over and including 10mm thick backing coat in CM 1:4complete complete all as specified and as directed. |
| 24 | Material and Labour for Vitrified tiles 10mm thick (square/rectangular) light coloured, area of each tile not exceeding 0.36 sqm of any shade and any pattern (Pattern consists combination of two or more tiles ) in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed of 15mm thick in CM 1:4 complete all as specified and as directed. |
| 25 | Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 26 | Demolition of cement concretereinforced (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided complete all as specified and as directed. |
| 27 | Material and labour for Plain cement concrete 1:3:6, type C1, using 20mmgraded stone aggregate as in bed block for hold fastincluding necessary form work all as specified and as directed. |
| 28 | Material and Labour for point wiring complete using 1.5 Sqmm PVC insulated unsheathed copper conductor, stranded cable (FR) upto and including working voltage 1100volts grade, drawn through and including non metallic rigidPVC conduit not less than 20mm drawn in concealed conduit in wall and open conduiton ceiling including all accessories ISI marked including factory made galvanised modular flush sheet metal enclosure having top bottom side and back wall knock out for conduit entry from any direction suitable to the approved make of switch/socket outlet conforming to IS 14772-2000 and suitable for for cover plates and unsheathed copper conductor stranded cable (FR) earth continuity wire connected to DBs/sunken boxes/fittings of size 1.5 Sqmm Cross sectional area and all other metal parts with earth dolly for the following:-(a) onelight point controlled by one switch 5 Amps |
| 29 | (b ) onefan pointpoint controlled by one switch 6 Amps |
| 30 | (c) One 3pin socket outlet 6 Ampson Independent board |
| 31 | (d ) One 3pin socket outlet 6 Ampsonsame board |
| 32 | All as per Item No. 28 above but with 4 sq mm PVC insulated copper conductor cable(FR) including 4 sq mmPVC copper conductor used as earth wirefor power point on independent board |
| 33 | Supply and fix Modular switch one way 6A, 1 Module complete all as specified and as directed. |
| 34 | Supply and fix Modular Switch socket combintation, 3pin, 5 Amps flush type 3 module complete all as specified and as directed. |
| 35 | Supply ans fix Modular socket combination 16 A, 6 pin, 3 module complete all as specified and directed. |
| 36 | Supply and fix LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.Make: Havells /Philips/Bajaj. |
| 37 | Supply and fixing LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. Make: Bajaj / Havells/Philips/Crompton Greaves. |
| 38 | Supply and fixing round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.Make: Crompton /Philips/Havells |
| 39 | Supply and fix Exhaust Fan of size 300 mm sweep with louvers, with metal body AC 230 V, 50 Hz, 1200 RPMand connecting to ceiling rose terminals with 23/.0076 flexible cable and making good the disturbed surface to match with existing finishes complete all specified and directed. Make: Cat No. Turbojet SP of Havells or equivalent in Usha/Crompton Greaves. |
| 40 | Supply and fixing of Ceiling rose in poly carbonate 3 plates flush type 6 Amps, 250 volts AC complete all as specified and directed. |
| 41 | Taking down ceiling fan of any type and size, cable ends, dimantling blades and removing fan and blades to store yard Scraping down old paint of ceiling fan of any size complete body & blade including down rod filling the cavitieswith filler and making smooth surfaceby applying sand paper painting the ceiling fan by meansspray gun/brush with synthetic enamel white paint complete all as specified and directed and Hanging/fixing including provision of cable from ceiling rose or connector to fan all as specified and directed. |
| 42 | Supply and fix MCB SP 6-32 amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB) of single pole in the MCB DB,IP 20 transparent lebel holder fully insulated safety shutters suitable for cable up to 35 Sqmm cross sectional area complete including suitable size copper Lugs complete all as specified and directed. |
| 43 | Supply and fix MCB SPN, 240Volts, 40 to 63 Amps rating 240 V, breaking capacity of 10 KA, \"C\" Curve complete all specified and as directed. |
| 44 | Supply and fix in repairs Distribution board (DB) made out of sheet metal enclosure (CRCA sheet), dust and vermin proof, SPN 8 way with 200 Amps rated copper bus bar double doorprotection, neutral bar,earth bar, single pole and neutral 240 volts, MCBs used as incommerDouble door, flush to wall complete all as specified and directed . |
| 45 | Material and labour for sub main wiring with 2 runs of 6 sqmm FRLS single core multistranded copper conductor PVC insulated andunsheatheddrawn through and including PVC conduit not less than 25mm dia size with all accessories such as bends,Tee, junction boxes, elbow etc fixed to walls/ceiling including 1 run of 6 Sqmm copper (insulated) FRLS cable as earth continuity conductor including complete all as specified and as directed. Note : 3 runs of 6 Sqmm copper cable and one run of PVC casing and caping shall be measured one unit length. |
| 46 | Schedule of Credit (Minus) Rs.8200.00NOTE: Bidder shall insert credit amount of Rs. 8200.00 as ratein Green field under Col-13. |
