Tender For Construction Work In Community Building Village Umren Under Range Bayana. - 1 Item Description 2 Earth work excavationbymechanical mean ( hydraulic excavatore manualmean over areas (exeeding 30 cm in depth 1.5cm in width as well as 10 sqm on plan)including disposel of excavated lead up to50mdispose earth to be levelled all kind of soil 3 Providing and laying in position cement concrete includingcuring, compaction etc. complete in specifiedgrade excludingthe cost of centering and shuttering - All work up to plinthlevel.1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size). 4 RANDOME RUBBLE STONE MASSONARY with hard stone infoundation and plith cement mortar above 30 cm thik wall in cement mortar 1:6 5 Supplying and fixing machine cut fine dressedRed/Pink sand stone dasa orcoping,with full moulding if required laid on cement mortar 1:4 including pointing with admixture of pigment matching with the stone shade. 75 mm thick 6 Brick work with F.P.S. bricks of class designation 75 insuperstructure above plinth level upto floor V level in allshapes and sizes in :Cement mortar 1 : 6 (1 cement : 6 coarse sand) 7 Providing and fixing horizontal chajja of Red/ White sandstone 40 mm thick and upto 80 cm projection in cement mortar1:4 (1 cement : 4 coarse sand) including pointing in whitecement mortar 1:2 (1 white cement : 2 stone dust) with admixture of pigment matching the stone shade. 8 Providing dab stone over Chajjas duly fixed in cement sandmortar 1:6 complete :50mm thick. 9 Supplying and fixing machine cut fine dressed Red/Pink san stone dasa or coping, with full moulding if required laid oncement mortar 1:4 including pointing with admixture ofpigment matching with the stone shade.25 mm thick 10 25 mm thick 11 75 mm thick 12 Providing and fixing steel gate, grating , and grills made ofangles, tees, square bars, flats,or black pipe with holdfast andfittings complete as per design and drawing including cuttingwelding and fabrication with priming coat of red oxide 13 Stone slab roofing on ground floor with fine grained stoneslab from approved quarry including filling of joints ofparapet and slab on both sides in cement sand mortar 1:4,with ceiling pointing in cement sand mortar 1 : 3 complete asper specification and instruction of Engineer In Charge 14 Fore slab 15 Providing and laying brick kharanja on roofs with cementmortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound in square pattern75mm to 100mm thick average 16 Plaster on new surface on walls in cement sand mortar 1:4including racking of joints etc. complete fine finish20mm thick . 17 Brick work with F.P.S. bricks of class designation 75 insuperstructure above plinth level upto floor V level in allshapes and sizes in : Cement mortar 1 : 6 (1 cement : 6 coarse sand) 18 Providing and applying white cement based putty overplastered surface to prepare the surface even and smoothcomplete New Plastered Surface (three or more coats) 19 Wall painting with plastic emulsion paint of approved brandand manufacture to give an even shade including allscaffolding: 12.40.1 Two or more coats on new work including prepartion of basewith primer, putty, lippy etc complete in all respect. 20 P & F 1st qualityVitrified Porcelain Polished tiles on floor,skirting and steps etc.in different sizes (thickness to bespecified by manufactuer) with water absortion less than0.08% and conforming to IS 15622 of approved make in allcolour and shade, laid with 20 mm thick CM 1 : 4 includinggrounting the joints with white cement and matching pigmentetc completesize 600 mm X 600 mm 21 HALL FLOOR 22 BARAMDA FLOOR 23 Total 24 Random rubble dry stone Kharanja under floor. 25 For Hall Floor 26 Total 27 Part B 28 Wiring of light point/ fan point/ exhaust fan point/ call bell point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (as per IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (as per IS:694) on surface ISI marked ( IS:14927 P - II ) UPVC casing capping& its accessories like coupler, inner, outer, elbow, square box, tee, end cap etc., recessed 18 SWG G. I. box with earth terminal/surface UPVC Boxwith earth terminal, 6 A switch 3 pin ceiling rose / lamp holder/ 3 point connector , 3.0 mm thick ISI marked phenolic laminated sheet (IS : 2036 -1995),Al. alloy/ cadmium plated iron screws 20 mm cup washers etc., all as per pre approved by Engineer in charge,making connections, testing etc. complete as required. For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessoriesrefer Chapter E - 04, E - 05 & E - 07 . For additional technical parameters of products/ work, referAnnexure A attached with this BSR . 29 Short point (up to 3 mtr.) 30 Medium point (up to 6 mtr.) 31 Long point(up to 10 mtr..) 32 Wiring of 3/5 pin 6 amp. Light plug point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal sizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694)and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694)onsurfaceISI marked ( IS:14927 P - II ) UPVC casing capping & its accessories like coupler, inner, outer, elbow, square box, tee, end cap etc., recessed 18 SWG suitable G. I. box with earth terminal/ surface UPVC Boxwith earth terminal, 6 Aswitch, 3/5 pin 6 A socket, 3.0 mm thick ISI marked phenolic laminated sheet (IS : 2036 -1995),Al. alloy/ cadmium plated iron screws 20 mm cup washers etc.all as per pre approved by Engineer in charge,making connections, testing etc. complete as required. For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessoriesrefer Chapter E - 04, E - 05 & E - 07 .For additional technical parameters of products/ work, referAnnexure A attached with this BSR . 33 On board 34 S&F following sizesof ISI marked ( IS:14927 P - II ) UPVC casing capping as per PWD specification for electrical Works along with all accessorieslike coupler, inner, outer, elbow, square box, tee, end cap etc. on surfacewithscrews, expansionfasteners , All as per pre approved by Engineer in charge, making connections, testing etc. complete as required. For additional technical parameters of products/ work, referAnnexure A attached with this BSR . 35 25 mm x 12 mm 36 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.99% purity copper, class 5 stranding in acc. to IEC 60228 forlower watt loss , oxygen free ( <10 ppm) for less chances of oxidization and higher silver content for gives better conductivity , insulation PVC type A ,flame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4,, in existingsurface or recessed PVC/ MS conduit/casing capping includingall as per pre approved by Engineer in charge,making connections, etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of products/ work, referAnnexure A attached with this BSR . 37 1 x 1.5 sq.mm 38 2 x 1.5 sq.mm 39 Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load andsite requirement) 4KV impulse withstand voltage,as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC,minimum phase termination capacity of 35sq.mm. , conductorline load reversibility, label holding facility , IP 20 contact protection and fitted withexisting distribution board/sheets, min. operation 20,000 upto 32 A rating and 10,000 upto 63 A, 5000 for 80 A ratingincluding making connections, testing etc. as required.. OEM shall have submitNABL / CPRI / ERDA accrediated lab test reportsbefore execution & All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 40 Single pole MCB 41 6 A to 32 A rating 42 Providing & Fixing of 240/415 V isolator as per PWD specification for electrical Works with ISI marked IS:13947-III/conforming to IEC 60947-3, suitable for AC22A utilization catagory, 4KV impulse withstand voltage,true contact indication,Red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting,minimum phase termination capacity of 35sq.mm. , label holding facility , IP 20 contact protection and fitted with existing distribution board / sheetincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab test reportsbefore execution & All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 43 Double pole isolator 44 30 A / 40 A rating 45 Providing & Fixing of IK09 recessed/surface mounting heavy duty horizontal type sheet steel of 1.6 mm thickDistribution board as per PWD specificationfor electrical Works ISI marked conforming to IS-13032 & IS-8623 / conforming to IEC 61439-3. Phosphatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link , neutral link, earth link , connecting wire of suitable rating and din bar,masking sheet, including making internal DBterminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.OEM shall have submitNABL / CPRI / ERDA accrediated lab test reportsbefore execution & All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 46 IP-43 Double door (single phase) 47 6 Way (6 O/G +2 I/C ) 48 Providing & Fixing of ISI marked (IS :3854) 16 amp. flush typenon modular switch as per PWD specification for electrical Works, made out from industrial grade Polycarbonate or fire resistant ABS material , minimum width of switch toggle should not less then18 mm, brass terminal & captive screws including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 49 Providing & Fixing of3/6 pin 16 amp flush type non modular socket as per PWD specification for electrical Works, made out fromindustrial grade Polycarbonate or fire resistant ABS material, brass terminal with Porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 50 Providing & Fixing of ISI marked (IS:1258)6 ampbatten/angle lampholder as per PWD specification for electrical Works,made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screws including making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 51 Providing & Fixing ofISI marked (IS:1293) 6 ampunbreakable 3 pin plug top with lamp indicator as per PWD specification for electrical Works, made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal including making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 52 Providing & Fixing of non modular socket size flush type 120 watt rotary minimum 5 step fan regulator as per PWD specification for electrical Works, ISI marked (IS:11037) made out from industrial grade Polycarbonate or fire resistant ABS material including making connection testing etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 53 Providing & Fixing offollowing size mounting grid plates with cover plates as per PWD specification for electrical Works, made from fire retardent UV established high performance engineering plastic suitable for all universal metal boxes for front installation & removal direct fit type complete in all respect.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 54 8 Module 55 10 Module 56 12 Module 57 16/18 Module 58 Providing & Fixing offollowing size hot dip galvanized M.S. box of 18 SWG as per PWD specification for electrical Works, with earthing terminal in recess/ surface suitable for modular accessories as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 59 6 / 8 module 60 10 / 12 module 61 16/18 module 62 Pipe Earthing as per PWD specification for electrical Works as per IS:3043- 1987 with 3.0 Mtr. Long, 40 mm dia. B class G.I. Pipe IS: 1239 (Part-1) 2004, Equivalent to BS : 1387 with perforated holes of 12 mm dia ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height250 to 300 mm. and embodying the pipecomplete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 63 Providing & Fixing of ISO Certified company made BEEStar rated copper wounded double ball bearing capacitor start, aluminium body & Metallicblade ceilingfanas per PWD specification for electrical Works, conforming to IS:374-2019, & IS:1885 -P-V- 1981. with down rod up to 30 cm with secondary support safety cable ( steel wire ) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required.Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . 64 1200 mm Sweep BEE 2 Star rated (service value >=4.5 to < 5 ) 65 Providing & Fixing of IP40 LED Recessed / Surface Mounted, Round / Sqaure Non-Dimmable Back lit SMD Mid Power LED Downlight with die-cast aluminum housing & Heat Sink for heat dissipation with UV Stabilized non yellowish Diffuser with internal/ external BIS complience 2.5 KV surge protected Isolated driver, with Short & Open circuit protection, having efficiency > 85% and in compliance to IEC standards. System Lumen efficacy of ≥ 120 lm / watt, THD < 10 % ,p.f.≥0.95, CRI >80,life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing onhousing. 66 OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer Annexure A attacheded with this BSR. 67 Surface Mounting 68 LED Downlight 12/14 W
