Sales : +91-777 804 8217
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 04-04-2025 | Corrigendum V (Hospital AGT - Date) | Date | 30-04-2025 |
| 2 | 20-03-2025 | Corrigendum IV (Hospital AGT - Date and Integrity Pact) | Date | 04-04-2025 |
| 3 | 10-03-2025 | Corrigendum III (Date and Forms - Hospital Agatti) | Date | 20-03-2025 |
| 4 | 05-03-2025 | Corrigendum II (Agattii Hospital Civil Drawing) | Other | 10-03-2025 |
| 5 | 19-02-2025 | Corrigendum I (Hospital at Agatti) | Date | 10-03-2025 |
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil |
| 2 | Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil. |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil |
| 4 | Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil |
| 5 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 6 | Filling in plinth or trenches underfloors, foundations in areas etc with red earth ( from main land) in layers not exceeding 20cm in depth, consolidating each depositedlayer by ramming and watering, lead upto 50 m and lift upto 1.5m including cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge |
| 7 | Carriage of materials by mechanical transport including loading, unloading and stacking lead up to 5 km, including all lifts involved as directed by the Engineer-in-Charge. Surplus Excavated Earth |
| 8 | Extra rates for quantities of earth works, executed: In or under water and/or liquid mud, including pumping out water as requiredNote for item no. 2.24:- The extra percentage rate is applicable in respect of each item but limited to quantities of work executed in these difficult conditions. The unit, namely, metre depth, to be considered for payment, shall be the depth measured from the sub soil water level up to the centre of gravity of the qty executed in difficult conditions. The depth shall be reckoned correct to 0.10 m, 0.05 m or more shall be taken as 0.10 m and less than 0.05 m ignored |
| 9 | Providing and applying Antitermite treatement by injecting chemical emulsion Imidacloprid emulsiable concentrate .075% for pre-constructional treatement and creating a chemical barrier as per IS 6313 (Part ll) 2001 for wall trenches, foundation, top surface of plinth filling, foundation of wall and floor, along the external perimeter of the building,etc. complete conforming to manufacturers specification and as directed by the Engineer-in-Charge.(Plinth area only to be measured for the payment ) (The above work shall be carriedout by an agency having sufficient experience and should ensure a warranty for a period of 10 years. Only skilled and experienced persons shall be employed for this purpose.) |
| 10 | Close timbering in case of shafts, wells, cesspits, manholes and the like including strutting, shoring and packing cavities (wherever required) etc. complete. (Measurements to be taken of the face area timbered). Depth exceeding 1.5 m but not exceeding 3 m |
| 11 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 12 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) |
| 13 | Providing and Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. |
| 14 | Providing and laying autoclaved aerated cement blocks filling with 150mm/230mm/300 mm thick AAC blocks laying in sunken portion with approved blockin cement mortar 1:4 ,cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge |
| 15 | Extra for laying concrete in or under water and/or liquid mud including cost of pumping or bailing out water and removing slush etc. completeThe quantity will be calculated by multiplying the depth measured from the sub-soil water level up to centre of gravity of concrete under sub-soil water level with quantity of concrete in cum executed under sub-soil water. The depth of centre of gravity shall be reckoned correct to 0.1m. 0.05m or more shall be taken as 0.1m and less than 0.05m ignored |
| 16 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level. Concrete of M30 grade with minimum cement content of 350 kg /cum. |
| 17 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level. Concrete of M30 grade with minimum cement content of 350 kg /cum. |
| 18 | Extra for laying reinforced cement concrete in or under water and/ or liquid mud, including cost of pumping or bailing out water and removing slush etc., completeThe quantity will be calculated by multiplying the depth measured from the subsoil water level up to the centre of gravity of the R.C.C. under subsoil water with the quantity of R.C.C. in cubic metre executed under subsoil water. The depth of centre of gravity shall be reckoned correct to 0.1 m. 0.05 m or more shall be taken as 0.1 m and less than 0.05 m ignored. No extra payment shall be made for placing reinforcement or centering & shuttering under sub - soil waterconditions. |
| 19 | Add for using extra cement in the items of design mix over and above the specified cement content therein |
| 20 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 21 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 22 | Providing fusion bonded Epoxy coating not less than 175 micron thickness and upto 300 micron to reinforcement barsof any diameter as per IS-13620-1993/ ASTM-775 M including repairs to cut ends,welded spouts and handling damages with reccomendedliquid epoxy compatible with the coating and testing of coating at plant etc complete as directed by engineer ion charge. |
| 23 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : Foundations, footings, bases of columns, etc. for mass concrete |
| 24 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 25 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : Columns, Pillars, Piers, Abutments, Posts and Struts |
| 26 | Centering and shuttering including strutting, propping etc. and removal of form for all heights :Stairs, (excluding landings) except spiral-staircases |
| 27 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : Weather shade, Chajjas, corbels etc., including edges |
| 28 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : Suspended floors, roofs, landings, balconies and access platform |
| 29 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 30 | Centering and shuttering including strutting, propping etc. and removal of form for all heights : Edges of slabs and breaks in floors and walls. Under 20 cm wide |
| 31 | Providing and laying autoclaved aerated cement blocks masonry with 150mm/ 230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). |
| 32 | Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:21850(Part 3) in super structure above floor 2 level up to floorV level in cement mortar 1:4 (1 cement :4 coarse sand). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work. |
| 33 | Providing and laying solid block masonry 20cm thick using best quality blocks ofavailable size in cement mortar 1:6 ( 1cement: 6 coarse sand )for walls at any area (including duct walls,fin walls skin / ledge wall ,kerb wall etc) .The rate including cost, conveyance and unloading at site and stacking of all materials, all labour, scaffolding, watering, curing etc complete as per the direction of Engineer in charge. |
| 34 | Providing and laying solid block masonry 10cm thick using best quality blocks ofavailable size in cement mortar 1:4 ( 1cement: 4 M. sand )for walls at any area (including duct walls,fin walls skin / ledge wall ,kerb wall etc) .The rate including cost, conveyance and unloading at site and stacking of all materials, all labour, scaffolding, watering, curing etc complete as per the direction of Engineer in charge. |
| 35 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 36 | Providing and laying factory made Precast concrete solid blocks of 200 mm thickness of grade M10 made of C&D waste from approved manufacturer in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 37 | Providing and laying factory made Precast concrete solid blocks of 200 mm thickness of grade M10 made of C&D waste from approved manufacturer in superstructure above plinth level up to floor V level. Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 38 | Providing and laying half block masonry with factory made Precast concrete solid blocks of 100 mm thickness of grade M10 made of C&D waste from approved manufacturer in superstructure above plinth level up to floor V level: Cement mortar 1:4 (1 cement : 4 coarse sand) |
| 39 | Providing material and labour for laying 18 to 20 mm Mirror Polished Kota stone of approved quality, selected and sorted for uniform color & texture, in internal/external flooring work. .Kota stone is to be laid and jointed with grey cement slurry mixed with pigment to match the shade of the slabincluding rubbing and mirror polishing completed withbedding of average 25 mm thickness cement mortar in 1:4 (1 cement : 4 coarse sand). |
| 40 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 41 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed Vitrified tiles Matt/Antiskid finish of size.Size of Tile 600 x 600 mm. |
| 42 | Providing and laying fully Vitrified matt tiles in different sizes (thickness to be specified by manufacturer),with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in allcolours & shade, in dadoing, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ Sq.m including grouting/filling thejoint with white cement & matching pigments,cost and conveyance of all materials, labour charges etc. complete at all levels as directed by Engineer-in-charge Size of Tile600x600 mm |
| 43 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. Area of slab over 0.50 sqm |
| 44 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 45 | Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work |
| 46 | Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. |
| 47 | Providing and fixing removable raised/false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of: (a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug. (b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-charge. (c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with lightweight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to ensure the quality of the product. 300 mm Finished Floor Height (FFH) |
| 48 | Providing and Fixing, uPVC factory-made, white colour casementLouvers made of extruded profiles. Profiles of frames and sash will be mitred cut and fusion-welded at all corners including drilling of holes for fixing hardware and drainage of water etc., making arrangements for fixing of hardware, EPDM gasket, 1.2 ± 0.2mm thick galvanised steel profile to be included in the required profile, the frame will be fixed to the wall with 8 mm x 100 mm long fasteners, all complete as per direction of Engineer-in-charge. The Rates inclusive of 6mm Glazing, Louvers, Locks, hardware hinges, handle and fitting etc. |
| 49 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners if required to be paid for separately) :For fixed portion.Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 50 | Providing and fixing 12 mm thick toughened fixed glass panel of approved brand and manufacture, including making necessary arrangements for fixing requiredfittings, all complete as per direction of Engineer-in-charge |
| 51 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). |
| 52 | Providing and fixing factory-made single extruded GRP (Glass Reinforced Plastic) solid door/window/clerestory windows & other frames/chowkhat, comprising of high-quality GRP material with an antibacterial finish and honeycomb structure for superior strength and durability. The frames shall be fabricated with miter joints, assembled using GRP adhesive and stainless steel (SS) full-threaded star-headed screws.The frame shall have a minimum density of 750 kg/m³, a compressive strength of 58 N/mm², and a modulus of elasticity of 900 N/mm². It shall also be termite-proof, borer-proof, water/moisture-proof, fire-retardant (Class A resistance to flame spread), and non-corrosive. The material shall comply with all relevant IS standards and be designed for long-term use in demanding environments such as hospitals.The frames shall be fixed in position using M.S. holdfasts/lugs or SS dash fasteners of the required diameter and length, ensuring proper alignment and stability. The installation shall be completed as per the design and direction of the Engineer-in-Charge.Note: For GRP solid frames, a minus tolerance of 5 mm in dimensions (depth and width) shall be acceptable. Variations on the plus side shall be acceptable; however, no extra payment shall be made for such variations. Frame size: 65 x 150 mm. |
| 53 | Providing and fixing factory-made single extruded GRP (Glass Reinforced Plastic) solid plain flush door shutter of required size, comprising high-quality GRP material with an antibacterial finish and a honeycomb core structure for enhanced strength and durability. The door shutter shall have a minimum density of 650 kg/m³, a screw withdrawal strength of 1800 N (Face) & 900 N (Edge), a minimum compressive strength of 50 N/mm², a modulus of elasticity of 850 N/mm², and a Class A resistance to the spread of flame.The door shall be termite-proof, borer-proof, water/moisture-proof, fire-retardant, and resistant to microbial growth, making it ideal for hygienic environments such as hospitals. The surface shall be smooth, non-porous, and designed for easy cleaning and maintenance.The door shutter shall be fixed with stainless steel butt hinges of the required size using full-body threaded, star-headed, countersunk stainless steel screws, ensuring secure installation and smooth operation. All work shall be carried out as per the direction of the Engineer-in-Charge.Note: Stainless steel butt hinges and necessary screws shall be paid for separately. Thickness: 35 mm. |
| 54 | Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured):Rectangular or square |
| 55 | Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367: Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc, Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. |
| 56 | Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with/without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately.Note:-Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: (i) Sites with basic wind speed > 45 m/sec as per IS 875- Part 3 (ii) Sites with structure height more than 20m for all wind speedsThree track three panel sliding window with aluminium channel for roller track, wool pile, nylon rollers with SS 304 body Using R2 series with frame (70mm & above) x (40mm & above) & sash (25mm & above) x (55mm & above) with zinc alloy (zamak) powdercoated handle on every panel with multipoint locking system (Height upto 1.8 metre). |
| 57 | Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367: Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc, Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. |
| 58 | Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with/without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately.Note:-Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: (i) Sites with basic wind speed > 45 m/sec as per IS 875- Part 3 (ii) Sites with structure height more than 20m for all wind speedsTwo track two panel sliding window with aluminium channel for roller track, wool pile, nylon rollers with SS 304 body Using R3 series with frame (55mm & above) x (40mm & above) & sash (30mm & above) x (55mm & above) with zinc alloy (zamak) powdercoated handle on every panel with multipoint locking system (Height upto 1.8 metre). |
| 59 | Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367: Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc, Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. |
| 60 | Two track two panel sliding door with aluminium channel for roller track,wool pile , zinc alloy (zamak) powder coated handle on every along multi- point locking system adjustable nylon rollers with SS 304 body. Using R3 series with frame (55mm & above) x (40mm & above) & sash (30mm &above )x (74mm & above)(Height upto 2.5m) |
| 61 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40mm thick :Float glass panes. 4 mm thick glass pane (weight not less than 10kg/sqm). |
| 62 | Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :Float glass panes. 5 mm thick glass pane (weight not less than 10kg/sqm). |
| 63 | Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367: Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc, Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. |
| 64 | Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with/without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately.Note:-Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for: (i) Sites with basic wind speed > 45 m/sec as per IS 875- Part 3 (ii) Sites with structure height more than 20m for all wind speedsFixed window/ventilator with mullion / transom Using R3 series with frame (55mm & above) x (45mm & above)(Height upto 2.5 metre). |
| 65 | Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). |
| 66 | Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c, including applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and asper direction of Engineer-in-charge with glass of required thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm. |
| 67 | Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded). |
| 68 | Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete. |
| 69 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 70 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 71 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm |
| 72 | Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles ofapproved quality with necessary screws etc. complete. |
| 73 | Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :100X58X1.90 mm |
| 74 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. |
| 75 | Supply and Installation of Handles for Glass Door of Stainless Steel Satin Finish, SS 304 Back To Back Pull Handles Dia. 25 mm,CTC Length 300 mm all complete, as per approved drawing and as directed by engineer in charge. |
| 76 | Supplying And Fixing Glass to Glass Hook Lock of Dorma make WG-300G-G/G-PC45-NI-DCSSS series or equivalent for Frameless glass double door with 60mm EPC - both side key , all complete as per approved drawings and as directed by engineer in charge. |
| 77 | Supplying And Fixing a pair of fire rated Solid SS Lever Handle and Mortise Lock case with Cylinder of approved size and quality for 2 hr fire rated steel doors etc complete all works including all required fixtures as directed by Engineer in Charge. |
| 78 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of crosssection 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. |
| 79 | 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge. |
| 80 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm |
| 81 | Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. |
| 82 | Providing and fixing an SS sliding mosquito net for windows and doors involves custom-measuring the window or door, sourcing durable stainless steel mesh, and installing a sturdy frame with sliding tracks. The mesh size is of 18 x 16 OPI (openings per inch, 18 openings per inch horizontally and 16 openings per inch vertically). The net is securely attached, and the sliding mechanism is set up for smooth operation. Professionals ensure a perfect fit, easy sliding, and long-lasting protection against mosquitoes, offering a practical, rust-resistant solution for homes and businesses. |
| 83 | Providing and fixing a 40mm thick lead-lined flush door shutter with vinyl covering, including a 2mm thick lead sheet for radiation shielding and vinyl finish on both sides. The door shall be installed with a 65x100mm hardwood frame and shall include all necessary fittings and accessories, such as hinges, locks, door closer, handles, and screws, ensuring proper installation all complete as directed by Engineer in Charge. |
| 84 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 85 | Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge. |
| 86 | Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin-charge. The product performance shall carry guarantee for 10 years against any leakage. For vertical surface two coats @0.70 kg per sqm |
| 87 | Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin-charge. The product performance shall carry guarantee for 10 years against any leakage. For horizontal surface one coat @1.10 kg per sqm. |
| 88 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 89 | Providing and fixing stainless steel(grade 316) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) |
| 90 | 12mm cement plaster of mix1:4 (1 cement : 4 fine sand) including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels - Internal plastering |
| 91 | 15 mm cement plaster on the rough side of single or half brick wall of mix : : 1:4 (1 cement: 4 fine sand) |
| 92 | 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) |
| 93 | Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. |
| 94 | 12 mm cement plaster finished with a floating coat of neat cement of mix :1: 3 (1 cement: 3 fine sand)including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels. - |
| 95 | Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 96 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre |
| 97 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats |
| 98 | Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. |
| 99 | Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm |
| 100 | Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Alumini um sheets (each0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places |
| 101 | Curtain glazing-Design, Supply installation, fixing and testing curtain glazing system at all heights consisting of powder coated aluminium frame and glass of approved make, aluminium frame work fabricated out of heavy duty Aluminium extruded profile, powder coated with durable thermosetting polyester powder coating by electrostatic spraying and hard stoved to not less than 60-micron thickness to comply with BS 6496:1994 (1991) and AAMA 2603-98 standard as per approved metallic shade. All aluminium members and profile shall be of AC-25grade as specified. Mullions & Transoms, extruded aluminium sections shall be of 6063-T6 alloy to be decided as per structural calculations. The aluminium members shall be protected with protections tapes all around the profile for safety against external scratches at site. (Protection tape shall be removed only at the time of handing over as per the instructions of Engineer In Charge).The anchoring /bracing of the Al. sections to the RCC slabs /beams /columns/block masonry shall be done with required number of non-corrosive galvanized extended brackets of approved design (Galvanizing to be done conforming to IS: 4759-1996 up to 610 gms per SqM, 80-90 microns thickness) with approved dash fasteners of minimum 12mm dia and depth of minimum 100mm, in the concrete/ stainless steel bolts including providing and fixing aluminium shims of various thickness to adjust the beam level and line variation. The anchoring system should be designed to withstand the dead load of structural wall as well as stresses due to wind pressure as per IS code 875-Part III. (MS frame work to be provided wherever required will be measured separately for payment).(The detailed structural design calculations & shop drawings both vetted by IIT shall be provided by the executing agency and mock-up based on approved design has to be approved by Engineer In Charge before start of work.) |
| 102 | The glazing subframe shall be aligned for each vertical mullion of size 50 mm x 180 mm for the entire height and for each transom of size 50 mm x 75 mm for the entire width horizontally by laser beam equipment to ensure 100% x axis and y axis alignment. To make the joint water and air tight, the glazing sub frame work is provided with approved in built ventilation and drainage system. All the joints of the structural glazing system and the periphery of glass shall be properly sealed with specified weather silicon. The details of inbuilt ventilation and drainage system should be submitted by the contractor before execution. Heavy duty, best quality EPDM gasket of approved colour of suitable profile is provided at joints and connections between. The glass is to be fixed at the outer side of the aluminium subframe with structural silicon sealant of approved make & colour (the structural silicone bite size shall not be less than 6 mm as per the structural design calculation or requirement/as per manufacturers recommendation).All screws, washers, Bolts, Nuts and Anchors used shall be only stainless steel of 316 grade etc. complete as per direction of Engineer in Charge. Curtain wall should be sealed to hoist structure and allow movements, ensure water tight and water proof etc. in its service life. Item includes cost of design, supply, installation, fixing aluminium frame with structural members, mullions, transom, sub frame, fixtures etc, including glass as specified below, cost of sealants, brackets, fasteners, screws, sleeve, spacer tape, backer rod, bolts, gasket, scaffolding, transportation, all taxes etc. complete in all respect and as directed by engineer in charge for the following items. Etc. (The above work shall be carried out by an agency having sufficient experience and should ensure a warranty fora period of 10 years. Only skilled and experience persons shall be employed for this purpose).Glass - 6 mm thk performance Glass.High performance glass U value less than or equal to 5.6+-0.1 Watt/m2k, SF-0.47+-0.02,SC -0.54+-0.2,VLT>43%, External reflection<11%, Internal reflection<18% etc.Provide Horizontal and vertical Aluminium Capping 50 mm x 100 mm in line with tender drawings, all visible surfaces shall have high Durability (Akzonobel) / Super durable (Jotun) Powder coating of 60 - 80 micron confirming. The non visible aluminium surfaces shall have minimum chromatizing treatment. |
| 103 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 104 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer\"s specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work |
| 105 | Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture\"s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. |
| 106 | Providing and Fixing Polycarbonate Plain Sheet involves supplying 4mm thick polycarbonate sheets, as approved by the Engineer, in a single length of 12 meters (or as per the Engineer\"s decision). These sheets will be installed using self-drilling/self-tapping screws (5.5x55mm) with EPDM seals, and can be fixed on horizontal, vertical, or curved surfaces, with the cost of purlins, rafters, and trusses excluded. The installation includes cutting the sheets to required sizes and shapes and must comply with ISI mark standards for quality. |
| 107 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. |
| 108 | Providing and Fixing ofBuilding signages as per following specifications - Sign to be made shall be made of 3 mm aluminium / Acrylic Box Letters (100mm thick letters). Sign Face shall be in 3mm 0/40 Translucent Acrylic with Male / 10mm Water Proof Sun board Female Joint Adequate LED of Samsung Make shall be fitted with the required wiring & Waterproof Transformer to have the uniform Light. A provision for Weather Proof Box shall be made to keep the Transformers. The signages to be fixed on the structural ACP + MSframework with required sizes as per the design. The item includes design of supporting arrangement, fabrication, installation and commissioning the signages with structural framing including channels, angles, gusset plates and anchoring the frame by anchor fasteners to the Building. The structural framing should be painted with primer and enamel paints |
| 109 | Frosted Film - Supply & laying ofFrost/Privacy Film appoved design and color for All Glass Partitions and GLass doors. Rate including laying.(The successful vendor should submit 10 years Warranty certicate to the clients. Product to be certified by Manufacturer\"s Representative) |
| 110 | Egress fire exit Signage- Ceiling recess mounted -Supply & fixing of LED unit fixed on ceiling which is lit internally.The LED is prolite make). Sleek exit/Egress edgelit lights recess mounted as pproved by the architect. Signage to have UPS back up in built.Fixed on to the existing background with necessary chains & hooks |
| 111 | Room/Function identification holders signs made of imported clear acrylic of size 127mm x 127mm x5mm thickness . The room location will be made 0.8mm raised computer cut with 16mm high. Signage will be painted with DuPont paint as per approved shade card. |
| 112 | Room/Function identification holders signs made of 127mm x 127mm x3mm thick SS fixed on 3mm thk foam board with double sided tape.The room location will be made 0.8mm raised computer cut with 16mm high. Signage will be painted with DuPont paint as per approved shade card. |
| 113 | Providing control joints in 6mm Width x 10 mm depth at 3m X 4m panels along the length and breadth of the entire screed area. The joint can be provided by using a saw cutting machine attached with a 3 mm blade within 18-24 hrs of application of the screed.28- 30 days later, these joints can be filled with one-part moisture-curing Polyurethane Sealant.The rate is including cost and conveyance of all materials, labour charges, scaffolding, sundries etc complete as directed by the Engineer-in-Charge at all levels. |
| 114 | Grading roof for water proofing treatment with Cement concrete 1:2:4 |
| 115 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x0.90 mm M.S. laths with 0.90 mm thick top cover |
| 116 | Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer-in- charge, (area of grill to be measured). |
| 117 | Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 118 | Providing and fixing Gysum false ceiling (12.5 mm) at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer\"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS Certification marks) |
| 119 | Providing & fixing 8 mm thick Calcium Silicate false ceilingat all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture\"s specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with: 8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process. |
| 120 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level,suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \"T\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \"T\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \"T\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \"T\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \"T\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyesterpaint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. |
| 121 | Providing and fixing of Ceiling pelmet for curtains, made in plywood and Gysum ceiling with paint finish at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer\"s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS Certification marks) As per design approved by Architects. |
| 122 | Providing and fixing 450mm wide Pantry unit made with 710 grade prelaminated plywood in approved wooden laminate shade on shutters and all visible areas. Best quality telescopic sliders,hinges,locks,hardware to be provided. (HETTICH/DORMA/HAFELE OR EQ) as per drawing and 3D.counter top laid with steel grey granite with bullnose rounded edge . |
| 123 | Providing & fixing TV unit ledge of 30mm thick with back panelling in lobby made with 16mm plywood box work with all visisble area in laminate finish 1MM MERRINO 10510 MAGUS WALNUT BRONZE and 3mm groove at 60cm intervals as per 3D and drawing. |
| 124 | Providing ,supplying & fitting of vanity counters/ wash basin counters with cabinets of carcase with 19mm tk BWP 710 grade plywood with laminate finish &wooden edge band,16mm tk BWP 710grade pywood shutters with self closing hinges. counter top with granite or fullbody tile laid over 8 mm thick multiwood board, with cement based high polymer modified quick set adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete allas directed by the Architect.Extra for providing opening of required size & shape for wash basin, vanity counter and similar location ingranite or fullbody tile ,including necessary holes for pillar taps etc.Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer\"s specifications including appropriate priming coat, preparation of surface, etc. on complete steel work |
| 125 | Providing & supplying of Mirror fixing in toilet, above Toilet wash counter to provide 6mm edge polished mirror SAINT GOBAIN or equivalent fixed with mirror stud. |
| 126 | Providing and fixing wardrobes and cabinet with 16mm thick Marine plywood box work with inside area approved 1 mm thick frosty white laminate, shutter with 19mm Plywood with 1mm thick GREENLAM 930 SGL GLISTEN on all visible areas. Best quality telescopic sliders,hinges,locks,hardware to be provided. (HETTICH/DORMA/HAFELE OR EQ) as per drawing and 3D |
| 127 | Providing and fixing registration,pharmacy and admin counters with 16mm and 12mm thick marine plywood with approved shade 1mm thick laminate ( GREENLAM GLISTEN 930SGL) on all visible areas. Internal laminate finish in white. Table to have CPU stand,key board tray, wire manager, footrest, 3 drawers with multi latch locks,telescopic sliders and all required soft close hardware. Top covered with 19mm edge bullnose Black granite as per drawing. |
| 128 | Providing & fixing2 seater sofa with dimension -1550 mm Width x750 mm Depth x 950 mm Height.Frame shall be made of combination of 12 mm moisture resistance and termite free plywood and pine wood (without knot)having cross section 34x64mm.Seat - shall be made of slab stock foam of density of base 28 kg/ meter cube and super soft 32 kg/meter cube at top. Seatshall be embeded with 2mm pocket spring.Seat Back - made of slab stock foam of density 28 kg/ meter cube pasted on back. Front of the back rest shall be made ofloose conjugated polyester fiber webbing.Legs - legs shall be made of rubber wood.Facia - facia of the sofa shall be made of membrane pressed MDF. |
| 129 | Providing & placing three seater waiting chair. CROSS BEAM: It should be made up of black powder coated rectangularM.S.ERW tube having 8.0 ± 0.03 cm x 4.0 ± 0.03 cm x 0.2 ± 0.014 cm size.LEG AND ARMREST: It should be chrome plated made of cold rolled steel with 0.12 ± 0.013 cm thinkness.SEAT/BACK SHELL: It should be powder-coated perforated shell made from cold rolled M.S. sheet.The Side Bar should be made of Chrome plated solid steel 3.0 ± 0.03 cm x 1.2 ± 0.3 cm with fluting and plastic inserts. The Shell should be assembled on the Cross Beam with help of M8 Bolts .Overall Dimensions:Seat Height - 40.0cm, Height - 67.5 cm, Width & Depth of Chair as - Width-163.0cm and Depth-57.0 cm |
| 130 | Supplying of Fourseater waiting chair. 4 seater perforated metal bench -Cross beam and Leg shall be powder coated made of cold rolled steelwith 0.2 ± 0.01 cm thickness. Seat-Back shell shall be 1.2 mm thk powder-coated perforated shell made from cold rolled M.S. sheet 0.12 ± 0.013 cm thickness. The Side Bar shall be made of powdercoated solid steel with in serts. The Shell shall be assembled on the Cross Beam with help of bolts . Seat width- 54.5 cm per seat. Thickness of side bars is 4.5cm & gap between seats is 2cm. Overall Dimensions shall be Seat Height - 40.6 cm, Height - 77.5cm, Width & Depth of Chair as measured from ground - Width-176.5 cm and Depth-71 cm.Dimensions tolerance / variations shall be within +/- 1 cm. |
| 131 | Providing and fixing conference table of size 3500 mm width x 1200 mm depth. Legs shall be made from 25 mm PPB having a straight profile with half round edges and clad with 0.6 mm thick post forming laminat. Overall thickness of leg shall be 26.2 mm.Modesty panel of understructure shall be made of 18 mm thick Pre laminated Twin Board. |
| 132 | Providing & fixing conference and admin chair. SEAT/BACK ASSEMBLY: The seat should be made up of 1.2 ± 0.1cm. thick hotpressed plywood and upholstered with leather and moulded Polyurethane Foam. The back foam should be designed withcontoured lumber support for extra comfort. BACK SIZE: 53.0cm.(W) X 95.4cm.(H) SEAT SIZE: 54.6cm.(W) X 49.0cm.(D) HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HRpolyurethane foam should be moulded with density = 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf for 25% compression.SEAT-BACK CONNECTING SPINE:The seat and back should be arrested together with spine made of 0.8 ±0.05 cm thkHR Steel and should be black powder-coated ( DFT 40-60 microns ).ARMREST ASSY: The armrest assy. should comprise of three parts viz. the armrest support tube and P.U. armrest and thearmrest top. The armrest tube assy. should be made of 2.54±0.03cm x 0.16±0.0128cm M.S. E.R.W. support tubes andChrome plated. The P.U. armrest should be made of black integral skin polyurethane with 50-70 shore \"A\" Hardness andreinforced with M.S. insert. The armrest top should be made of ABS & upholstered with foam & leather. FRONT PIVOT SYNCHRO TILT MECH.: The mechanism should be designed with the following features:•360° revolving type.•Seat back tilting ratio of 1 : 1.5•Front pivot for tilt with feet resting on ground ensuring more comfort.•Tilt tension adjustment.•5-position locking with anti-shock back mechanism, which prevents the backrest from impacting the user when the lockshould be released.•Static seat depth adjustment = 5.0 ± 0.5cm with 5 position locking.PNEUMATIC HEIGHT ADJUSTMENT: it has an adjustment stroke of 9.0 ± 0.3cm.BLOW MOULDED BELLOW : The bellow should be 1 piece and blow moulded in black Polypropylene.PEDESTAL ASSY: The pedestal should be made of die-cast aluminium with buffing finish. It should be fitted with 5nos. twinwheel castor. The pedestal should be 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with castors).TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black Nylon. |
| 133 | Providing & fixing examination chair. SEAT/BACK ASSEMBLY: The seat and back should be made up of 1.2 ±0.1cm, thick hotpressed plywood, upholstered with fabric and moulded Polyurethane foam with PVC lipping all around. The back foamshould be designed with contoured lumbar support for extra comfort.POLYURETHANE FOAM: The polyurethane foam should be moulded with density = 45 ±2 kg/m\" and Hardness = 20 ±2 onHampden machine at 25% compression.TUBULAR FRAME: The tubular frame should be cantilever type & made of 0 2.54 ±0.03cm. x 0.2 +0.016cm. M.S. E.R.W.tube and black powder coated ( DFT 40-60 microns ).The Armrest Tube of 0 2.54 +0.03cm. x 0.2 ±0.016cm. M.S. E.R.W.tube should be welded to mainframe. The desklet should be fitted on the right hand side.DESKLET ASSEMBLY: The wooden desklet should be made of 1.8 ±0.05cm. thk. pre-laminated particleboard with 0.15±0.03cm. thk. P.V.0 lipping all around.ARMRESTS: The one-piece armrests should be made of black integral skin polyurethane foam with 50-70 Shore hardnessand reinforced with M.S. insert. The armrests should be scratch and weather resistant tant.PAPER TRAY: The paper tray should be made of 0 0.4 +01-0.005cm. M.S. wire spot welded to form a mesh. It should beblack powder coated. |
| 134 | Providing and fixing Nurses station Table with 16mm and 12 mm thick marine plywood with 1mm thick Laminate finish (GREENLAM 930 SGL GLISTEN)on visible areas. Bottom portion covered in Wooden laminate shade (MERRINO-10510 MAGUS WALNUT BRONZE) and steel skirting as per 3D image and drawing. Top and sides covered with 12mm CORIAN (LG- HI-MACS W007 LENTIL) eased edge. Internal finish with laminate in 0.8mm Frosty white mattas per drawing and 3D images. |
| 135 | Providing & fixing consultation table with written of 1500x750 mm H. Primary Work Surface shall be Made of25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to topSoft closing access flap with in-build power box are provided on work surface for wire management.Secondary Work Surface of the green guard by ul certified table shall be made of 25mm thick MDF one side pre-laminateboard confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVCmembrane pressed on to top. There shall be a desk pad of width 800 mm and depth 430 mm made of 1 mm thich artificialleather glued on 1.2 mm thick GI sheet a per IS 277.Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS12823:1990, Edge banded with matching 2 mm thick PVC lipping.Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS12823:1990, Edge banded with matching 2 mm thick PVC lipping.Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming toIS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-BOX-FILE type which Usespowder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM.Drawers have a soft closing & anti slam mechanism.Handles are provided for ease of opening.Pedestals are provided with lock for security. |
| 136 | Providing and supplying High back chair. SEAT/BACK A SSEMBLY: The seat is made up of 1.2 + 0.1cm thk. hot pressed plywoodmeasured as per QA method described in OCP-QLTA-PL14-18.The Back is made up of injection mou1ded glass filled nylon& upholstered using Mesh fabric with high tenacity yarn.HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45+/-2 kg/m°and hardness 16 + 2 kgf as per IS:7888 for 25% compression.ARMRESTS : The adjustable armrest is designed with Up-Down adjustment— 8 steps (8 0+0.Scm range) Height adjustable armrest structure which is Powder Coated & fitted with an armrest top. Fixed Armrest Top is PU moulded over metal insert.LUMBAR SUPPORT ASSEMBLY: The Lumbar support consists of polypropylene pad with moulded polyurethane foam &covered with polyester fabric.The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rearside of the pa6. Lumbar pad has an adjustment of 8.0 + 0.5 cm in height.FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designedwith the following features. 360° revolving type.Single point control. Front-pivot for tilt with feet resting on ground ensuring more comfort. Tilt tension adjustment.4-position locking with anti-shock feature.Seat/back tilting ratio of 1:2.NECKREST : The Neckrest assembly consist of polypropylene pad with moulded polyurethane foam & covered withpolyester fabric Neckrest is fixed to Back Assembly through Neckrest connector Neckrest assembly has height adjustment. |
| 137 | Providing and fixing visitors chair,The seat and back are made of injection moulded high impact strenght polypropylene polymer compound with indoor grade UV Resistance.The tubular weled frame is made from Dia2.22 +/- 0.03cmx 0.12+/- 0.0128 cm and 3.5+/- 0.03 cm x 0.12+/-0.0128 cm stainless Steel 202 grade tube.The tube of green guard by ul certified chair shall be buffed polished to give shinyfinish. The Shoes are made of high impact strenght polypropylene polymer compond with indoor grad UV Resistance andpressed fitted with tubularfram. |
| 138 | Supply & fixing ofpatients Steel Stools with cushions, size 21\"ht 14\" dia cushion fabric top and stool legs of 1\" dia SS tube |
| 139 | Providing & fixing dinning table of 90cm dia 3 Seater,made up of plywood confirming to IS 710 withPU Coating . The table top shall be provided with 1 mm thk laminate.Legs are made up of harwood/Ashwood. All exposed faces finished with PU polish for wood frames . |
| 140 | Providing & fixing Study table with prelaminated plywood confirming IS 710 grade 16mm ,with 1mm thick laminated fixing on drawer shutters and all visible areas.Best quality accessories and telescopic sliders for drawers to be used(HETTICH/DORMA OR EQ) (TABLE SIZE: 900MMX50MMX75MM, DRAWER SIZE: 300MMX150MM[H]) |
| 141 | Providing and fixing of linear workstation Table top 1200x600x750mm of 25mm thick Pre-laminate particle board E1 norms finished with 2mm pvc edge banding on all expossed edges.Under-structure : Supported on MS powdercoated CONNECT leg with supporting beams.Wire management : 65mm Dia grommet and Below Table Top 250 mm ht laminate fascia.Raceway &separator for power & data cable management. MS vertical cover for wire entry. |
| 142 | Providing & supplying Bystander Cot made with hardwood frame work and plywood box work covered with laminate of approved shade.Head Board made with 12mm plywood fixing at 16mm plywood box work with laminate in approved color on all visible areas. Accessories and hardware,6 inches foam/coir mattress of approved brand (customised dimension to fit cot) to be provided as per approved architects drawing. |
| 143 | Providing, supplying & fixing of dining chairs,frame & legs are made up of Ashwood having matching finish or walnut finish ploish.Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density wrapped in high end soft fabric of Italian leather.All exposed faces finished with PU polish for wood frames. |
| 144 | Supply & fixing Singleseater sofa of 80x65 x 68 cm with Frame structure madeAshwood frame work wit canes and legs are made up of ashwood.Upholstery works were provided with High-resilience polyfoam seat cushions with 50m density and having walnut finish ploish.All exposed faces finished with PU polish for wood frames . |
| 145 | Providing & fixingTeapoy of 900x600mm and Glass should be 12 ±0.3 mmtoughened glass uv glued with bushes made in ss 202 grade for fixing with under structure. it should be a welded assembly made in ss202 grade having dia 12mm. |
| 146 | Providing & fixingTeapoy of 750x400mm and Glass should be 12 ±0.3 mmtoughened glass uv glued with bushes made in ss 202 grade for fixing with under structure. it should be a welded assembly made in ss202 grade having dia 12mm. |
| 147 | Providing & fixingTeapoy of 450mm dia and Glass should be 12 ±0.3 mm toughened glass uv glued with bushes made in ss 202 grade for fixing with under structure. it should be a welded assembly made in ss202 grade having dia 12mm. |
| 148 | Providing & fixingTeapoy of 500mm dia and Glass should be 12 ±0.3 mm toughened glass uv glued with bushes made in ss 202 grade for fixing with under structure. it should be a welded assembly made in ss202 grade having dia 12mm. |
| 149 | Providing & fixingTeapoy of 900mm dia and Glass should be 12 ±0.3 mm toughened glass uv glued with bushes made in ss 202 grade for fixing with under structure. it should be a welded assembly made in ss202 grade having dia 12mm. |
| 150 | Providing & fixingtable with prelaminated plywood confirming IS 710 grade 16mm ,with 1mm thick laminated fixing on drawer shutters and all visible areas.Best quality accessories and telescopic sliders for drawers to be used(HETTICH/DORMA OR EQ) (TABLE SIZE: 1500MMX75MMX75MM, DRAWER SIZE: 300MMX150MM[H]) |
| 151 | Supply and installation of a dining table in outdoor dining area with an aluminium frame, powder-coated for enhanced durability and corrosion resistance. The frame should be woven with high-quality synthetic wicker, providing an attractive, durable, and low-maintenance finish. The table should feature a toughened glass top, tempered for additional strength and safety. The dimensions of the table are as follows: Width 200 cm, Depth 100 cm, and Height 75 cm.The quoted rate shall include the cost of all materials and labours, tools and tackles etc complete and as per directions of Engineer-in-charge. |
| 152 | Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete.8mm thick.Granite of any colour and shade |
| 153 | Providing and fixing of wall panelling with 19 mm thick BWP 710 fire retardant plywood conforming to IS: 5509 /10701 grade internal frame work and 12 mm thick fire retardant plywood conforming to IS: 5509 /10701 grade . Exposed area finishing with 12 mm thk. BWP 710 fire retardant plywood conforming to IS: 5509 /10701 grade with veneer-A grade finish and one coat of PU coat and flexiply with veneer covering combination, with SS Gold finish profile 20mm, with all necessary fittings and labour charges, as per design approved by Architects. |
| 154 | Providing and installation ofAcoustic wall panelling with 12mm pet panels of size: 1220x2440 of weight 1800 g/m2, which are 50 % recyclable material has LEED MR-4, having NRC value upto 0.8 and 15 mm Wood Fiber of size: 600x1200mm of density 410 kg/m3, with Green (VoC,RC%)-Low 10, having NRC value upto 0.9,with polyester fibre infill of 500GSM. Fixed with GI struts of Web Width 48mm, depth 48mm, 0.6mm thickness are used to form frame from ceiling to floor of CC – 600mm framing on both the planar sides from(Vertical & Horizontal). Above this framing, one side first layer will be gypsum board of 12mm thick and second layer will be 15 mm wood wool board and another side will two layer of 12 mm thick gypsum board of approved make. Wood wool boards, pet panels and gypsum boards are installed using black phosphate or nickel pated bugle head fine threaded screws horizontally or vertically as per the architecture design and infill is used to fill the gap between the frames. The rates for above works are inclusive of all cost materials incluidng fabric, fabrication charges, transportation and installation, labour, etc complete, as per design approved by Architects. |
| 155 | Providing and fixing of wallpaper with paper backing with 220-250 GSM. The wallpapers are printed on either low VOC, or PVC-free LEED-certified substrates- either of which are intended for a range of commericial applications. These are fixed with Bartoline or equivalent-all purpose wallpaper adhesive with high quality and which is easy to mix. As per design approved by Architects. |
| 156 | Finishing walls with textured interior paint of required shade: New work (Two or more coats applied @ 3.28 ltr/ 10 sqm ) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm |
| 157 | Supplying and installation of Black out roman blinds as per the detailed Technical specification and deatiled drawing. Including all fixing charges and necessary fittings. Base rate of fabric is Rs. 700/- |
| 158 | Supplying and installation of Black out roller blinds as per the detailed Technical specification and deatiled drawing. Including all fixing charges and necessary fittings. Base rate of fabric is Rs. 700/- |
| 159 | Supplying and fixing of Main curtain(Size:345X220 cm), with polyester based cotton blend pleated curtains. Including all fixing charges and necessary fittings. |
| 160 | Providing and fixing Cubicle curtains made by 2400 square inch treads,100% Polyester Fabric,Fungus Retardent, Water repellant,Stain retardent,and easy washable.Curtains gsm 175to180 gsm. |
| 161 | Providing and fixing CubicleTracks made of AlluminumAlloy of Box size 1.7x20x25mm with 50-60 microns powder coating in white color.Tracks are bend to a radius at 90 degree.Wall Bracket:Made of CRC steel with white powder coating finish. Bridge Clamp:Made of CRC steel with white powder coating finish.RoofSuspension:Made of aluminum pipe of 12.5mm &20mm diameter.The upper circular plate made of aluminum with 50.4mm diameter thickness.Curtain Removal Point is Made of SS.Runner: Comprises of Wheel type runners made of Teflon ISS material for easy and smooth sliding of curtain. Including all fixing charges and necessary fittings. |
| 162 | Providing & supplying Patients Cot 36\" wide x 80\" length ,made of combination of mettallic and plastic,finishing by Pretreated and Epoxy Powder Coated.Provided by adjustable height for the entire bed, the head, and the feet, adjustable side rails, and electronic buttons to operate both the bed and other nearby electronic devices and are mounted on wheels allowing for mobility. Including soft furnishing items,necessary fittings and fixing charges. |
| 163 | Providing & supplying ICU bed (200x90x60cm) made up ofFrame work of M.S. Tube ,Pair of Foldable Aluminum Side Rails, head and foot board. Four section top made up of perforated MS Sheet. provided with 2 brakes and holder for Urine bag.finished with pretreated & Epoxy Powder Coated/ Baked Paint and Five Function available with manual operation Functions are Head End Elevation, Foot End Elevation, Hi-Low, Trendelenburg, Reverse Trendelenburg. Including soft furnishing items,necessary fittings and fixing charges. |
| 164 | Providing & supplying Eletrical delivery bed (200x90x60cm) single size bed made up of Frame work of M.S. Tube ,Four section top made up of perforated MS Sheet,Pair of Foldable Aluminum Side Rails,head and Foot Panel.Provided with holder for Urine bag,Backrest elevation,Knee rest elevation,High/Low movement and Provision for I.V. Rod at all corners. Including soft furnishing items,necessary fittings and fixing charges. |
| 165 | Providing and fixingexamination couch with cabinets . Body section covered with sheet for 3 sides . It comes with three drawers & three cabinet. It has 2 section coushioned top. It has adjustable backrest by gas spring system.Ithas inbuilt foot step for patients. Product size: 183L X 50W X 82 H |
| 166 | Providing & supplyingmanually operated SNCU beds 180x150x13cm ,made up of frame work of rectangular M.S Tube and 2 Section top made of perforated M.S Sheet,having head & foot Panels. finished with pre treated and Epoxy powder Coated. Including soft furnishing items,necessary fittings and fixing charges. |
| 167 | Providing and supplying an examination couch, Model MEDIK-MX-168 (Medik168), with overall dimensions of 72” length, 24” width, and 32” height. The couch is equipped with an adjustable headrest for customizable positioning, three drawers for storing medical instruments or supplies, and two shelves with doors for secure and organized storage. It features a 2-inch high-density cushion to ensure patient comfort and is finished with epoxy powder coating for enhanced durability, corrosion resistance, and ease of maintenance. The product must comply with relevant healthcare standards, with materials and workmanship of the highest quality. Delivery and installation are to be completed at the specified location within the agreed project timeline. |
| 168 | Providing and supplying a multifunctional couch/dialysis couch made of a strong and stable platform, designed to meet versatile medical requirements. The couch features a head cushion and armrests on both sides, with dimensions of 1950 mm in length, 650 mm in width without armrests, and height adjustable between 530 mm and 800 mm. The armrests, measuring 450 mm in length and 160 mm in width, are vertically and horizontally adjustable, can be moved out for easy entry of patients or donors, and provide enhanced flexibility and convenience. The couch offers motorized height adjustments and allows adjustment of the backrest, leg rest, height, Trendelenburg, and Reverse Trendelenburg positions, and can be converted into a chair position. It has a lifting capacity of at least 150 kg and comes with an IV rod attachment. The couch is equipped with four lockable castor wheels for ease of movement and stability. It features extra-thick, disinfectant-resistant upholstery for durability and hygiene. Delivery and installation are to be completed as per the project requirements. |
| 169 | Providing & fixing of 90x200 cm size cot with base, legs, and frame works made up of Ashwood or hardwood furniture and provided with a fabric headboard of imported fabric and provided with provision for 10\" mattresses. The cot will be finished with a matching finish or walnut finish. All exposed faces will be finished with PU polish for the wood frames. |
| 170 | Providing and supplying a premium model pediatric bed with wheels and mattress, featuring crank-operated back-raise adjustment up to 75°. The bed dimensions are 1787 mm in length, 1034 mm in width, and 1285 mm in height (with ±1% tolerance). It comes with epoxy powder-coated sliding side rails for safety, and a pressed steel bottom for durability. The bed is equipped with 100 mm diameter casters, with brakes on opposite corners, allowing for easy mobility and secure positioning. Additionally, the bed includes a provision for an I.V. hanger rod attachment. The mattress is designed for comfort and support, and delivery and installation will be completed as per the specified requirements. |
| 171 | Providing and supplying a stretcher on trolley, Model MEDIK-152, with dimensions of 80” length, 22” width, and 33” height. The stretcher features a strong MS tubular frame mounted on four swivel castors for easy maneuverability. It includes a removable stretcher top made of stainless steel sheet with a powder-coated finish for durability and easy maintenance. The stretcher is equipped with provisions for IV attachment and an oxygen cylinder carrier, making it suitable for emergency and medical transport purposes. Delivery and installation are to be completed as per project requirements. |
| 172 | Providing and fixing ABS plastic, anti-rust, easy to clean bed side lockers. Including one drawer and equiped with a door wth glass holder, towel shelf on two sides with castor(2 with brake). Size:48x48x81cm. |
| 173 | Providing and fixing locker cabinets and drawers made from MS CRCA sheet, stainless steel top with raised edge on 3 sides, castors 2 with brakes, pre treated powder coated finish. |
| 174 | Providing and fixing over bed table, frame made of rectangular square tube with body section mounted on 5 cm castors, with laminated top of 75cmx 40cm with height adjustable gear handles. |
| 175 | Providing and fixing trolley with integral ABS surface and special concave top. Framework made of round SS tube 202 Grade & 304 grade, product size: 70x45x90cm. |
| 176 | Providing and fixing corridor handrails cum wall guard of4\" dia complete with continuous aluminum retainer and vinyl cover . Complete with mouting brackets, end returns and fixing accessories. Fixed at 1000mm (upto centre) from finishedfloor level. |
| 177 | Providing and fixing 52mmx52mm corner guard complete with continuous aluminum retainer and vinyl cover. Complete with top caps,end returns and all fixing accessories.Fixed on walls above skirting |
| 178 | Providing and fixingrigid pvc sheet 1mm sheet for wall protection, complete with top caps and silicon filling for joints.( To be used as kick plates on doors - size 4\"x2\"). |
| 179 | Providing and fixing foam mattress comes in 4 sections. It is covered with rexin closed with zip at one end. It is used on full fowler bed. Product size:190x90x10 |
| 180 | Procuring healthy grass free from weeds and foreign materials and laying on the soil medium as turfing,the rate include for grass cost, transport to site, cost and application of manure, planting, labour, supervision and maintenance for 2 months after plantingPearl Grass |
| 181 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting.Royal palm |
| 182 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting.Foxtail palm |
| 183 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting.Bismarkia palm |
| 184 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting.Jackfruit tree |
| 185 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting.Elenji tree |
| 186 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting.Coconut tree |
| 187 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting.Malpighia Topiary in steel mesh |
| 188 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting.Eugenia Topiary |
| 189 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting.Clerodendrum Inerme -Hedge |
| 190 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting.Murraya Exotica - Flower bush |
| 191 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting.Heliconia Caribea |
| 192 | Procuring and planting specified nursery grown trees, shrubs and other plants .Rates include plant cost,transport, cost of manure, planting, labour,supervision and maintenance for 2 months after planting.Areca tree |
| 193 | Supplying , stacking and spreading sludge / well decayed farm yard manure from thesource,Mixing earth and manure or in proportion specified or directed, Spreading ofdung manure or / and good earth in required thickness.and fine dressing the ground as per natural gradiantapproved by the engineer in charge incl. screening, loading, unloading, conveyance and stacking at site. |
| 194 | Providing and Placing in position suitable PVC water stops conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete : Serrated with central bulb (225 mm wide, 8-11 mm thick) |
| 195 | Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25 |
| 196 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-inCharge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern. |
| 197 | Providing and fixing at or near ground level factory made RCC pavement slab of M-30 grade of size 450x450x50 mm, including reinforcement with 6 mm dia M.S. bars 4 nos on each side, including setting in position in footpath to the required level and line over a bed of 20 mm average thick cement mortar 1:5 (1 cement : 5 coarse sand), having joint thickness not more than 5mm except on curve, including filling of joints with same cement mortar and making grooves etc. complete as per direction of Engineer-in-charge. |
| 198 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineerin-charge). |
| 199 | Painting runway/taxi track/apron marking with adequate nos of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-incharge, i/c cleaning the surface of ail dirt, scales, oil, grease and other foreign mater;al etc. and lining out complete. New work (Two or more coats) |
| 200 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 201 | Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 202 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. |
| 203 | 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 204 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 205 | 2 X 4 sq. mm + 1 X 4 sq. mm earth wire |
| 206 | 2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 207 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 208 | 20 mm |
| 209 | 25 mm |
| 210 | 32 mm |
| 211 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. |
| 212 | 5/6 A switch |
| 213 | 2 way 5/6 A switch |
| 214 | 15/16 A switch |
| 215 | 3 pin 5/6 A socket outlet |
| 216 | 6 pin 15/16 A socket outlet |
| 217 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 218 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. |
| 219 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. |
| 220 | 1 or 2 Module (75mmX75mm) |
| 221 | 3 Module (100mmX75mm) |
| 222 | 4 Module (125mmX75mm) |
| 223 | 6 Module (200mmX75mm) |
| 224 | 8 Module (125mmX125mm) |
| 225 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 226 | 8 way , Double door |
| 227 | 12 way , Double door |
| 228 | 16 way , Double door |
| 229 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 230 | 6 way (4 + 18), Double door |
| 231 | 8 way (4 + 24), Double door |
| 232 | Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) |
| 233 | 4 way (4 + 12), Double door |
| 234 | 8 way (4 + 24), Double door |
| 235 | 12 way (4 + 36), Double door |
| 236 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 237 | Single pole |
| 238 | Double pole |
| 239 | Triple pole |
| 240 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. |
| 241 | Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.25 A |
| 242 | Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 A |
| 243 | Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A \"C\" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required. |
| 244 | Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
| 245 | Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. |
| 246 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 247 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 248 | Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 249 | Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm) |
| 250 | Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm) |
| 251 | Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required. |
| 252 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. |
| 253 | Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required. |
| 254 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required. |
| 255 | Upto 35 sq. mm |
| 256 | Above 35 sq. mm and upto 95 sq. mm |
| 257 | Above 95 sq. mm and upto 185 sq. mm |
| 258 | Above 185 sq. mm and upto 400 sq. mm |
| 259 | Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. |
| 260 | Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 261 | Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) |
| 262 | Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp) |
| 263 | Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp) |
| 264 | HT CABLE LAYING: Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing masonry open duct as required.Above 120 sq. mm and upto 400 sq. mm |
| 265 | MV CABLE JOINTING & END TERMINATION: Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 266 | 3½ X 25 sq. mm (28mm) |
| 267 | 3½ X 35 sq. mm (32mm) |
| 268 | 3½ X 50 sq. mm (35mm) |
| 269 | 3½ X 70 sq. mm (38mm) |
| 270 | 3½ X 95 sq. mm (45mm) |
| 271 | 3½ X 150 sq. mm (50mm) |
| 272 | 3½ X 185 sq. mm (57mm) |
| 273 | 3½ X 240 sq. mm (62mm) |
| 274 | 3½ X 300 sq. mm (70mm) |
| 275 | 3½ X 400 sq. mm (82mm) |
| 276 | 4 X 10 sq. mm (25mm) |
| 277 | 4 X 16 sq. mm (28mm) |
| 278 | 4 X 25 sq. mm (28mm) |
| 279 | HV CABLE JOINTING & END TERMINATION: Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :300 sq. mm |
| 280 | RMU |
| 281 | 11KV Outdoor Metering Cubicle: SITC of 11KV Outdoor Metering Cubiclecomprising of : 3 Nos. Current transformer (---/5A,15VA,class 0.2s) 1 No.Potential transformer(11KV /110V,100VA,class 0.2) Separate Compartment for CT/PT and TOD Meter with KSEB sealing facilityTTB with Fuse and CarrierProvision for incoming and outgoing XLPE 11 KV Cable and cable entry from bottom side withcable box suitable for 3 x 300 sqmm XLPE, 11KV Al: cable Enclosure-Powder coated CRCA sheet 2MM –IP 54 |
| 282 | 11KV TOD Meter: SITC of 11KV/ √3 / 110V/ √3 , Class 0.2S , 15VA HT TOD Meter suitable for mounting outdoortype with all standard accessories.11 KV KSEB metering cubicle, lead wires etc.complete Carrying CT/PT units with TOD meter for testing and calibrating at the KSEB Testing Lab and taking back the same to the site isincluded in the scope of the contractor.Statutory testing fees shallbe remitted and will be reimbursed against producing original receipt |
| 283 | 11KV Multi Panel System (VCB/LBS/LBS): SITC of H.T 4 Panel comprising of : Incomer1 No. Indoor type 11kV, 630A, 26.3kA for 3 sec Horizontal Draw out VCB fittedwith Manual / Motor operated spring charging mechanism with 230V AC motor andmotor control switch, shunt trip coilof 24V DC, closing coil of 24V DC, Auxiliary Contact 6NO + 6NC, MechanicalON/OFF indicator,mechanical operation counter, master trip relay , auxilliary relay with multifunction meter, voltmeter with selectorswitch and 3 nos ammeter , necessary cast resin current transformer(45/5A , Cl:5P10,/ Cl: 1,15 VA-dual core),Potential transformer ( 11KV/110V , Cl:0.2 , 25VA ) Anti pumping feature, instantaneous IDMT relay withMicroprocessor based 3O/C + and 1E/F Protection relay, Strip Heater with thermostat , Power pack230V AC-24 V DC emergency OFF push button with Aluminium busbar and copper earthing strip, incoming cable entry at bottom suitable for 3 x 300sqmm 11KV XLPE Al: cable Outgoing3 Nos. Indoor 11kv,630A, 26.3 kA for 1 sec Load Break Switch Panel consist ofmechanical / electrical Trip bush button ,ON/OF Indicator ,Space heater with thermostat , 230V AC shunt trip coil HT HRC Fuses links with Aluminium busbar and copper earthing strip, on HVside Rigid Bus Bar interonnection to the TransformerCompletewithallinterconnection , powder coatedapproved color control wiring,earth bus ofadequate capacity & double earthing to all breakersetc.as per ElectricalInspectorate / KSEB Standards. |
| 284 | 11kV/433v,500KVA Cast Resin Transformer: SITC of Transformer comprising of : 11kV/433V ,500KVA ,50Hz,3phase,Vector Dyn 11 Resin Cast Indoor Transformer with off circuit tapping+5% to -5% in steps of 2.5% with winding temperature indicator and hooter with allstandard accessories as per IS 2026/77 on HV side Rigid Bus Bar interonnection to the 11KV LBS Panel and on LT side cable boxsuitable for 3 x 3.5 x300 sq.mm XLPE Al ; cablewith all standard fittings and accessories.Painting shall be carried out as per IS 631, impedance ofthe transformer shall be as per relevant standards. |
| 285 | NEUTRAL CTs: Supply & Fixing of 1no Cast Resin Neutral CT with ratio 150/5A ,15VA, Cl.5P10, fixed in a suitable M.S box with view glass. |
| 286 | HT CABLES: Supply of 11KV stranded compact circular aluminium conductor,conductors insulation screened withextruded semi conducting compound in combination with copper tape (0.3 kA for 1 sec.),cores laid up, inner sheath of PVC tape,galvanized steel flat strip armoured,and overall PVC sheathed cable conforming to IS 7098/11/85 with latest amendments & confirming to the GTP of Group Aof following sizes. 3C - 300 Sq.mm HT Cable |
| 287 | GENERATORS: SITC of D.G. set of following KVA 0.8 P.F.3 phase,50c/s,433V, comprising diesel engine, fuel tank, base plate,antivibration pad,battery, batterylead wire, battery charger self startingand self charging mechanism,and residential type silencer, control panel , in accoustic enclosure etc.with all standard accessoriesas per ElectricalInspectoratestandards and pollutioncontrol boardnorms. 500 KVA |
| 288 | NEUTRAL CTs: Supply & Fixing of 1 No. Cast Resin Neutral CT fixed in a suitable M.S. box with viewglass. 150/5A, 15VA, Cl.5P10 |
| 289 | L.T.PANELS: SITC of cubicle type mediumvoltage switch boards as per specificationsmentioned below, comprising ofACBs / MCCBs.,enclosed in 16 guage M.S.cubicle complete with angle iron frame work,panel doors , horizontal andvertical busbars and outgoing feeders,FRP separators, phase barriers,gaskets for door,feeders designations, etc.,Main Switch Board shall be capable of withstanding 50 KA fault level. The panelshall be suitable for erection on the floor using channel and fastners at regular intervals. All panels should have fire suppression system( Panel should confirm to BIS,IE rules,KSEI/ KSEB Standards) |
| 290 | MAIN MV PANELFree standing, floor mounting Switchboard fabricated out of 14SWG CRCA sheet with Top Cable entry facility at HT side for 4nos 500 KVA incomer & Cable/ Bus bar trunking facility at LT side1) Main Busbars: 800A,50KA TPN Aluminium Busbars – 1sets/sections; 2) Transformer 500 KVA Incomer: Moulded Case Circuit Breaker TP, 800A, 50KA Set 666.5A with Electronic release FD KIT, OC, SC, EF, Shunt& Isolation duty Current Limiting type – 2no4) Diesel Generator 500 KVA incomer -2 no. Metering and Indications:3Phase Digital Combination Meter with Ammeter, KW Meter, PF Meter Model EM6400 of Conserve or equivalent , 3nos Cast Resin Metering CTs, CL1,10VA 630/5, 3nos 2AControl fuses – 1setLED Type Red Yellow Blue (RYB), Red Amber Green (Close/Trip/Open) Indication Lamps with Control fuses and toggle switches – 1set3Phase Digital Voltmeter 0-500V Model DM3256 of Conzerv or equivalent and 2A Control fuses - 1setRelays: Stand by Earth fault relay 10-40% 1.3sec IDMT & 400/5 Class 10P10,15VA,415V Resin cast protection CT - 1set; AMF Relay + PLC based Synchronisation Relay5) Outgoing Feeders:Moulded Case Circuit Breaker TP, 630A, 36KA– 2nosMoulded Case Circuit Breaker TP, 500A, 36KA– 4nosIsolator TP, 400A - 1noProvision shall be made for sealing of all shutters. |
| 291 | APFC PANEL - 150 KVArSITC of APFC Panel comprising of : Incomer : 1 No. 250A, TPN, IsolatorIndication/Protection 1 SetR,Y,B LED Type Phase Indicating Lampswith 2A SP MCB as control.1 No. 8 STAGE APFC Relay. 1 Set TPN AL: Bus bars Suitably rated Outgoing 1 No.125A TP Capacitor Switching Contactor with 125 A TPN SFU withHRC Fuses Coupled with 1no 50 KVAr Capacitor. 3 No. 63A TPN SFU with 63A HRC Fuses Coupled with 3 no 25 KVAr Capacitor. 3 No.40A TP Capacitor Switching Contactorwith 40 A TPN SFU withC152:C163HRC Fuses Coupled with 3 no 10 KVAr Capacitor. 2 No.16A TP Capacitor Switching Contactor with 16 A TPN SFU withHRC Fuses Coupled with 2 no 5KVAr Capacitor. Completewithallinterconnection , powder coatedapproved color control wiring,earth bus of adequate capacity & double earthing to all switches etc.as per ElectricalInspectorate / EB Standards. |
| 292 | SSB GFSITC of Floor Panel comprising of :Incomer : 1No. 500A TPN Isolator; 1 Set TPN AL: Bus bars Suitably rated Metering/Indication : 1 Set.R,Y,BLED type Phase Indicating Lamps with 2A SP MCB as control. 3 Nos.MFDM (KW,KWh,V, A,F ); 3 Nos .500/5A,CL:1, 15VA CTs Outgoing: 1 No. 250 A 25kA TP MCCB; 1 No.200 A 25kA TP MCCB; 2 Nos.100 A 25kA TP MCCBas outgoing;1 No . as Spare. Completewithallinterconnection , powder coatedapproved color control wiring,earth bus of adequatecapacity & double earthing to all switches etc.as per ElectricalInspectorate / EB Standards. |
| 293 | SSB FFSITC of Floor Panel comprising of :Incomer : 1No. 250A TPN Isolator; 1 Set TPN AL: Bus bars Suitably rated Metering/Indication : 1 Set.R,Y,BLED type Phase Indicating Lamps with 2A SP MCB as control. 3 Nos. 0-100A Ammeter.; 3 Nos .250/5A,CL:1, 15VA CTs Outgoing: 1 No. 160 A 25kA TP MCCB; 1 No.100 A 16kA TP MCCB; 1 No.100 A TP MCBas outgoing;1 No . as Spare. Completewithallinterconnection , powder coatedapproved color control wiring,earth bus of adequatecapacity & double earthing to all switches etc.as per ElectricalInspectorate / EB Standards. |
| 294 | SSB SFSITC of Floor Panel comprising of :Incomer : 1No. 250A TPN Isolator; 1 Set TPN AL: Bus bars Suitably rated Metering/Indication : 1 Set.R,Y,BLED type Phase Indicating Lamps with 2A Control fuse as control. 3 Nos.MFDM (KW,KWh,V, A,F ); 3 Nos .250/5A,CL:1, 15VA CTs Outgoing: 1 No. 100 A 16kA TP MCCB; 2 Nos.80 A 16kA TP MCCB; 2 Nos.63 A TP MCBas outgoing;1 No . as Spare. Completewithallinterconnection , powder coatedapproved color control wiring,earth bus of adequatecapacity & double earthing to all switches etc.as per ElectricalInspectorate / EB Standards. |
| 295 | SSB COMMONSITC of Floor Panel comprising of :Incomer : 1No. 500A TPN Isolator; 1 Set TPN AL: Bus bars Suitably rated Metering/Indication : 1 Set.R,Y,BLED type Phase Indicating Lamps with 2A Control fuse as control. 3 Nos.MFDM (KW,KWh,V, A,F ); 3 Nos .250/5A,CL:1, 15VA CTs Outgoing: 1 No. 100 A 16kA TP MCCB; 2 Nos.80 A 16kA TP MCCB; 2 Nos.63 A TP MCBas outgoing;1 No . as Spare. Completewithallinterconnection , powder coatedapproved color control wiring,earth bus of adequatecapacity & double earthing to all switches etc.as per ElectricalInspectorate / EB Standards. |
| 296 | HVAC PANELSITC of Floor Panel comprising of :Incomer : 1No. 500A TPN Isolator; 1 Set TPN AL: Bus bars Suitably rated Metering/Indication : 1 Set.R,Y,BLED type Phase Indicating Lamps with 2A Control fuse as control. 3 Nos.MFDM (KW,KWh,V, A,F ); 3 Nos .500/5A,CL:1, 15VA CTs Outgoing: 3 Nos. 200 A 25kA TP MCCB as outgoing;1 No . as Spare. Completewithallinterconnection , powder coatedapproved color control wiring,earth bus of adequatecapacity & double earthing to all switches etc.as per ElectricalInspectorate / EB Standards. |
| 297 | HVAC SUB PANELSITC of Floor Panel comprising of :Incomer : 1No. 200A TPN Isolator; 1 Set TPN AL: Bus bars Suitably rated Metering/Indication : 1 Set.R,Y,BLED type Phase Indicating Lamps with 2A SP MCB as control. 3 Nos.MFDM (KW,KWh,V, A,F ); 3 Nos .200/5A,CL:1, 15VA CTs Outgoing:7 Nos.80 A 16kA TP MCCB as outgoing;1 No . as Spare. Completewithallinterconnection , powder coatedapproved color control wiring,earth bus of adequatecapacity & double earthing to all switches etc.as per ElectricalInspectorate / EB Standards. |
| 298 | SSB OTSITC of Floor Panel comprising of :Incomer : 1No. 160A TPN Isolator; 1 Set TPN AL: Bus bars Suitably rated Metering/Indication : 1 Set.R,Y,BLED type Phase Indicating Lamps with 2A Control fuse as control. 3 Nos.MFDM (KW,KWh,V, A,F ); 3 Nos .160/5A,CL:1, 15VA CTs Outgoing: 1 No. 120 A SET @ 100A 25kA 4P MCCB;1 No. 100 A SET @ 80A 25kA 4P MCCB as outgoing;1 No . as Spare. Completewithallinterconnection , powder coatedapproved color control wiring,earth bus of adequatecapacity & double earthing to all switches etc.as per ElectricalInspectorate / EB Standards. |
| 299 | UTILITY PANELSITC of Floor Panel comprising of :Incomer : 1No. 500A TPN Isolator; 1 Set TPN AL: Bus bars Suitably rated Metering/Indication : 1 Set.R,Y,BLED type Phase Indicating Lamps with 2A Control fuse as control. 3 Nos.MFDM (KW,KWh,V, A,F ); 3 Nos .500/5A,CL:1, 15VA CTs Outgoing:2 Nos.200 A 25kA TP MCCB; 4 Nos.100 A 25kA TP MCCB; 1No. 100A TP Isolator as outgoing;1 No. as Spare. Completewithallinterconnection , powder coatedapproved color control wiring,earth bus of adequatecapacity & double earthing to all switches etc.as per ElectricalInspectorate / EB Standards. |
| 300 | PUMP PANELSITC of Floor Panel comprising of :Incomer : 1No. 100A TPN Isolator; 1 Set TPN AL: Bus bars Suitably rated Metering/Indication : 1 Set.R,Y,BLED type Phase Indicating Lamps with 2A Control fuse as control. 3 Nos.MFDM (KW,KWh,V, A,F ); 3 Nos .100/5A,CL:1, 5VA CTs Outgoing: 4 Nos. 25 A TP MCB; 3 Nos. 16 A TP MCB as outgoings.;coupled with: 1 Nos. Star/Delta Starters (upto 14 KW) with: 1 Sets. \"ON\" \"OFF\" luminous Push Buttons with 1NO- 1NC contacts. 1 No . 25 A TP MCBas Spare. Completewithallinterconnection , powder coatedapproved color control wiring,earth bus of adequatecapacity & double earthing to all switches etc.as per ElectricalInspectorate / EB Standards. |
| 301 | LAUNDRY PANELSITC of Floor Panel comprising of :Incomer : 1No. 200A TPN Isolator; 1 Set TPN AL: Bus bars Suitably rated Metering/Indication : 1 Set.R,Y,BLED type Phase Indicating Lamps with 2A Control fuse as control. 3 Nos.MFDM (KW,KWh,V, A,F ); 3 Nos .200/5A,CL:1, 15VA CTs Outgoing:6 Nos.63 A TP MCB as outgoing;1 No . as Spare. Completewithallinterconnection , powder coatedapproved color control wiring,earth bus of adequatecapacity & double earthing to all switches etc.as per ElectricalInspectorate / EB Standards. |
| 302 | LIFT PANELSITC of Lift Panel comprising of : Incomer : 1 No. 100A, TPN Isolator. 1 Set.R,Y,BLED type Phase Indicating Lamps with 2A Control fuse as control . 1 Set TPN AL: Bus bars Suitably rated Metering/Indication : 1 Set.R,Y,BLED type Phase Indicating Lamps with 2A Control fuse as control. 3 Nos.MFDM (KW,KWh,V, A,F ); 3 Nos .100/5A,CL:1, 15VA CTsOutgoing : 2 Nos. 63 A 100 mA 4PRCBO; 2 Nos. 63 A 4P MCCB ; Completewithallinterconnection , powder coatedapproved color control wiring,earth bus of adequatecapacity & double earthing to all switches etc.as per ElectricalInspectorate / EB Standards. |
| 303 | UPS PANEL - MEDICAL EQUIPMENT - 125 KVASITC of Floor Panel comprising of :Incomer : 1No. 200A TPN Isolator; 1 Set TPN AL: Bus bars Suitably rated Metering/Indication : 1 Set.R,Y,BLED type Phase Indicating Lamps with 2A Control fuse as control. 3 Nos.MFDM (KW,KWh,V, A,F ); 3 Nos .200/5A,CL:1, 15VA CTs Outgoing:3 Nos. 63 A TP MCB; 1 No 40 A TP MCB as outgoing; 2 Nos. 40 A 30mA 4P,RCBO; 1 No . as Spare. Completewithallinterconnection , powder coatedapproved color control wiring,earth bus of adequatecapacity & double earthing to all switches etc.as per ElectricalInspectorate / EB Standards. |
| 304 | UPS PANEL - 10 KVASITC of UPS PANEL comprising of : Incomer : 1 No. 63, TPN Isolator. 1 Set.R,Y,BLED type Phase Indicating Lamps with 2A Control fuse as control . 1 Set TPN AL: Bus bars Suitably rated Outgoing : 2 Nos. 40 A, 4P,RCBO; 2 Nos. 25 A, DP,RCBO ; Completewithallinterconnection , powder coatedapproved color control wiring,earth bus of adequatecapacity & double earthing to all switches etc.as per ElectricalInspectorate / EB Standards. |
| 305 | UPS PANEL - 30 KVASITC of UPS PANEL comprising of : Incomer : 1 No. 63, TPN Isolator. 1 Set.R,Y,BLED type Phase Indicating Lamps with 2A Control fuse as control . 1 Set TPN AL: Bus bars Suitably rated Outgoing : 2 Nos. 40 A, 4P,RCBO; 2 Nos. 25 A, DP,RCBO ; Completewithallinterconnection , powder coatedapproved color control wiring,earth bus of adequatecapacity & double earthing to all switches etc.as per ElectricalInspectorate / EB Standards. |
| 306 | 30 KVA UPS - Three Phase SITC of 30kwFrame with5kw x 6 modules three phase in and out. withindoor (IP21) with surge protection system with 60 min backup battery @ 30kva .8 PF load with min VAH of48000 Dual string (SMF battery ofreputed approved make. Input pf >0.99,with externalinput isolationtransformer, with IGBTrectifier andinverterDouble conversiontechnology, with inputvoltage range 320-460 @ full load, 50Hz Three Phase,output400V, 50HzThree phase, compatibility etc. |
| 307 | 10 KVA UPS - Three Phase SITC of10kwFrame with 3.4kw x 3 modules threephase in and out. Withindoor (IP21) with surge protection system with60 min backupbattery @ 10kva .8 PF loadwithmin VAH of16320 Dual string(SMF battery of reputed approvedmake. Input pf >0.99,with externalinput isolationtransformer, with IGBTrectifier andinverterDouble conversiontechnology, with inputvoltage range 320-460 @ full load, 50Hz Three Phase, output400V, 50HzThree phase, compatibility etc. |
| 308 | 125 KVA UPS - Three Phase SITC of120kwFrame with 30kw x 5 modules threephase in and out. Withindoor (IP21) with surge protection system with60 min backupbattery @ 10kva .8 PF loadwithmin VAH of16320 Dual string(SMF battery of reputed approvedmake. Input pf >0.99,with externalinput isolationtransformer, with IGBTrectifier andinverterDouble conversiontechnology, with inputvoltage range 320-460 @ full load, 50Hz Three Phase, output400V, 50HzThree phase, compatibility etc. |
| 309 | SUPPLY OF LT CABLE: Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. |
| 310 | 1 X 240 sq. mm |
| 311 | 3 X 4 sq. mm |
| 312 | 3½ X 25 sq. mm |
| 313 | 3½ X 35 sq. mm |
| 314 | 3½ X 50 sq. mm |
| 315 | 3½ X 70 sq. mm |
| 316 | 3½ X 95 sq. mm |
| 317 | 3½ X 150 sq. mm |
| 318 | 3½ X 185 sq. mm |
| 319 | 3½ X 240 sq. mm |
| 320 | 3½ X 300 sq. mm |
| 321 | 3½ X 400 sq. mm |
| 322 | 4 X 6 sq. mm |
| 323 | 4 X 10 sq. mm |
| 324 | 4 X 16 sq. mm |
| 325 | 4 X 25 sq. mm |
| 326 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable PVC box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C |
| 327 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable PVC box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 328 | Wiring for light point/ fan point / exhaust fan point / call bell point with 1.5 sq.mm FRLS PVC insulated copperconductorsingle core cable in surface / recessedmedium class PVC conduit,with modular switch, modular plate,suitable GI box and earthing the point with 1.5sq.mm.FRLS PVCinsulatedcopper conductor single core cable etc. as required for; |
| 329 | Two light controled by one switch. |
| 330 | Three light controled by one switch. |
| 331 | Four light controled by one switch. |
| 332 | Five light controled by one switch. |
| 333 | S\" type M.S. fan hook fabricated from suitable dia. M.S. rod duly painted for fixing of ceiling fan. The \"S\" type hook shall be fixed to steel bar in RCC ceiling. The ceiling shall be replastered with sand, cement & neeru etc. The cost of labours for chipping out ceiling upto steel bar & fixing of \"S\" hook & resurfacing the ceiling is included in the cost of item |
| 334 | FRP Cable Tray: Supply of the following sizes of Ladder Type FRP cable trays with vertical sides on both ends as per approved design and FRP supports with coupler plates spaced 300mm apart throughout the length as specified, including the cost of support hooks, fasteners, painting if required etc.( Contractor shall ensure to use corrossion free materials as support or fastening fittings) |
| 335 | 150mm(150x100x25) |
| 336 | 300mm(300x100x25) |
| 337 | 600mm(600x100x25) |
| 338 | RACE WAYS: Readymade 2500mm standard length, prefabricated, GI trunking from MS sheet and then hot dip galvanised, of following sizes and associated accessories such as coupler plates, tees, elbow etc. 50 mm side flanges shall be provided. Galvanisation thickness shall be minimum 86 Micron. cost of trunking shall be included junction box of suitable size, and all other accessories required to complete the work. |
| 339 | 100 x 40mm (W x H) - (14 SWG - 2mm) with cover without partition |
| 340 | 150 x 40mm (W x H) - (14 SWG - 2mm) with cover without partition |
| 341 | 300 x 40mm (W x H) - (14 SWG - 2mm) with cover without partition |
| 342 | IP 44 SS Floor Box (120 x 120 mm) - Flush mount floor box for concrete floors, IP 40 - for 3 Mosaic modules |
| 343 | LIGHT FITTINGS / FANS: SITC of following Light Fixtures/Ceiling Fans / Exhaust Fans |
| 344 | LED Downlight Recessed Fitting 15 W |
| 345 | LED Downlight Recessed Fitting 12 W |
| 346 | LEDRecessedLuminaire 36Watts |
| 347 | LED Linear Fixture 20Watts 4ftSurface Mounted |
| 348 | Mirror Light 5W |
| 349 | Ceiling Fan -1200 mm ( BLDC) |
| 350 | Exhaust Fan-450 mm |
| 351 | Bollard Lights |
| 352 | 50W Flood Light |
| 353 | 80W Flood Light |
| 354 | LIGHTNING PROTECTION: Air Terminal: Providing and fixing Fully Solid Vertical Air terminals for wind stability as per IS/IEC -62305 part-3. For 1,2,3,4 meter air terminal 16mm rod tapered to 10 mm aluminium rodmeter rod: Meets the requirement (IS/IEC 62305). Semi-hard (E-AlMgSiO5) Suitable for high wind load. All air terminal must have Interception Tip at the Top of air terminal. System consist of Fang Fix with base and clamp on the top air terminal is erected. Air terminal Joining Clip Stainless Steel SS 304 clamp made of cable bracket, lightning tested for 100 KA 10/350 micro sec waveform. Stainless Steel Wall Clamp or 16 KG stone of 365 mm diameter, high level of stability.No. of stones/wall clamps depending on wind load. Quick and easy mounting of interception rod using anchors. Concrete, frost-resistant, can be stacked. Govt approved Indian labs test certificate required. Make: Cape/Dehn |
| 355 | 2meterairterminalwith Interception Tip mountedon Stainless Steel WallClamp mounting accessories. |
| 356 | Parapet / Down Conductors: Providing & fixing of 8mm solid aluminium round conductor with necessary holders @ required interval as specified below:Meets the requirement of (IS/IEC 62305) : semi-hard (E-AlMgSiO5 )with 50 sq.mm cross sectional area. Govt approved Indian labs test certificate required. Make: Cape/Dehn |
| 357 | Conductor with Down Conductor Holder made of whether resistant plastic holder @ every 0.75 meters |
| 358 | Conductor with Terrace Conductor Fibre Reinforce Concrete holder @ every 0.75 meters |
| 359 | T-Connectors: ProvidingandfixingofCrossConnector/TConnector/FoldingClamp/ClampingShoe/ Expansion Piece: to route vertical down conductor /mesh formation made ofAluminiumFerruleusingscrewfreejoints.FoldingClamp/ClampingShoeformetalpanels(upto 20mmthicknessofthemetalframe):Foldingclamp/clampingshoeformetalframe thicknessupto20mm,madeofstainlesssteelSS304/316grade, conformstothe requirements accordingto (IS/IEC 62305). Expansion piece with connector:Forequalising temperaturerelatedlengthchanges.Necessaryonconductorslengthat every 20 meters horizontally. Using round conductor 8mm aluminium conductor with straight Connector: usingAluminiumFerrule. Quick installation using crimp joints. Conforms to the requirements according to (IS/IEC62305).Makesurealljointsare strong and willbe inspectedatsite.GalvanisedIronjointsarenotpermittedtoavoidriskofcorrosion. Single bolt joints are not permitted to avoid risk of faulty loose joints and reduce risk of flash over. Govt approved Indian labs test certificate required. Make: Cape/Dehn |
| 360 | Test Joints: Providing and fixing of Stainless Steel Test Joint suitable with suitable Outdoor Enclosure: For 8mm dia solid round aluminium conductor & 10mmdiacopper coated solidsteel roundconductorhaving100micronsofcopperbonding.Conformstotherequirements according to(IS/IEC62305).Theenclosureshouldbeoutdoorglass-fibrereinforcedpolycarbonate opaque having minimum inner dimension of 75mm x 75 mm x 50 mm. Thetestlinkhastobestraightandneedsminimum4mountingscrewsforstrongjoints Inspection of bimetallic corrosion at site required. Seperation of 8mm Aluminium & 10mm Copper bonded steel is required for future inspection and contractor has to make sure both conductors permitted. Govt approved Indian labs test certificate required. Make: Cape/Dehn |
| 361 | Ring Earthing: Providingandlayingcoppercoatedsteelsolidroundconductor10mmdiameterfrom earth electrode directly in ground as required. copper coated steel, high corrosion resistant. Meets the requirement of (IS/IEC 62305) copper coating thickness of100microns Should be tested and use exclusively for lightning protection earthing system and ring equipotentialbonding.AftertestlinkneedstoberoutedinsideHeavydutyconduittoavoid touch potential till ground level. Govt approved Indian labs test certificate required.Make: Cape/Dehn |
| 362 | Welded Joints: Installation of Exothermic WeldJoints for 10mm round copper bonded steel conductor having 100 microns as per IS/IEC 62305.Each under ground joints has to be wrapped withpetrolatum- coatedchemicalfibrefabrichaving1.1mmthickandwidth 50mm. Govt approved Indian labs test certificate required. Make: Cape/Dehn |
| 363 | Earth Pits: Providingandfixingofmaintenance freeEarthingsystemcomprises ofmolecularly bonded copper of 99.9% purity on low carbon steel of min 3048mm length (10 feet), having a diameter of 20mm with copper bonding thickness of 250microns asper UL 467. The Rod has to be either continuous or with self-coupling peg & bore arrangement with fault current withstand capability of 30 KA rms value for 1 second and I peak of 76 KA The rod must be having corrosion test, peel off test for uniform coating, 180 degree bend testwith out peeloff of copper bonding. Exothermic welded Clamp for clamping as suggested as per NBC 2016.Ordinary Stainless steel/Copper alloy universal clamps are not recommended. For self coupling peg & bore arrangement rod needs Impactpoint onthe bottom rod for easy insertion. Earth enhancing mineral compound is used for improving the soil conductivity. The material shall be mineral inert to sub soil and shall not pollutethe environment and non corrosiveto earth rod. Thematerial shouldhave aresistivity less than0.2Ωm. It should be free from hazardous substances.The mineral compound is required to have minimum 17.5 Kg ofthe total composite.The compound should be chemically inert and needs to submitGovt approved Indian labs test certificate. Concrete Earth electrode inspection chamber with weight bearing capacity of 50KN. The dimension shall be 320mmx 320mmx 190mm. Govt approvedIndianlabstestcertificaterequired. Make: Cape/Dehn |
| 364 | Solar Street Lights: SITC ofSolar Street Lightmounted on 2.5 inch dia. 5 meter height G.I Post comprising of :60W Monocrystalline panels , 26Ah Gell Battery , 15 Watts LED Street Light, Powder doated battery box and automatic ON/OFF Sensor etc. complete. |
| 365 | Solar PV: 100KW Common load |
| 366 | CCTV: Supplying and fixing of 25 mm Medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 367 | Supply and drawing of UTP 4 pair Cat 6 LAN cable in the existing surface/recessed PVC conduit as required.. one run |
| 368 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.. 63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 369 | DATA: Supplying and fixing of 25 mm Medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 370 | Supplying and fixing of 32 mm Medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 371 | Supplying and fixing ofGI box of following size modules, alongwith modular base & cover plate for modular switches in recess etc as required.. 1 or 2 Module (75mmX75mm) |
| 372 | Supply and drawing of UTP 4 pair Cat 6 LAN cable in the existing surface/recessed PVC conduit as required. one run |
| 373 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 374 | TELEPHONE: Supplying and drawing 2 pair, 0.5 sq mm FR PVC insulated copper conductor, un armoured telephone cable in the existing surface/recessed steel/ PVC conduit. |
| 375 | Supplying and fixing of 25 mm Medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 376 | Supplying and fixing of 32 mm Medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 377 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required.: Telephone socket |
| 378 | Supplying and fixing ofGI box of following size modules, alongwith modular base & cover plate for modular switches in recess etc as required.: 1 or 2 module( 75 mmx75 mm) |
| 379 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.: 63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 380 | TV: Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required |
| 381 | Supplying and fixing of 25 mm Medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 382 | Supplying and fixing of 32 mm Medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 383 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required.. TV antenna socket outlet |
| 384 | Supplying and fixing following size/ modules,GI box along with modular base, cover plate for modular switches in recess etc as required.. 1 or 2 module( 75 mmx75 mm) |
| 385 | CCTV: Supply, installation, testing and commissioning ofIP based IRVarifocal dome Camera, 1/3\" CMOS, 3 MP, 2.7–12 mm MFZ, night vision compatible,IR range of 40 mtrs PoE, inbuilt micro SD card,Ethernet port, H.264, IP 66, ONVIF, UL, FCC & CE certified. All mounting accessories shall be included |
| 386 | Supply, installation, testing and commissioning ofIP based IRbullet Camera, 1/3\" CMOS,3 MP,night vision compatible,IR range of 40 mtrs PoE,inbuilt micro SD card,Ethernet port, H.264, IP 66, ONVIF, UL, FCC & CE certified. All mounting accessories shall be included |
| 387 | Supply, installation, testing and commissioning ofIP based IR PTZ camera, 1/3\" CMOS, 2 Megapixel,30X zoom, WDR,IR range of 200 Meters, inbuilt micro SD card,,Ethernet port,TDN, PoE, DWDR, BLC, AGC, DNR, OSD,H.264 High Profile dual-stream, ONVIF, Wall/corner Mount, IP-66. CE, FCC, C-Tick certified. All mounting accessories and mounting arm suitable for the location shall be included |
| 388 | Supply,installation, testing and commissioning of IP Network Video Recorders 16 channel with 16 ports, 2 SATA, audio 1 input 1 output, video 1 HDMI 1 VGA, recording resolution 5MP/3MP/1080P, 720P/ D1 @ 30 fps, network throughput 200 Mbps from IPC and 128 Mbps to Client, Smart search supported, Remote access by DDNS & P2P, 4 channel alarm input and 2 channel relay output, 2 USB ports, ONVIF, UL & CE certified. |
| 389 | Supply, installation, testing and commissioning of 20 100/1000 SFP ports + 4 Combo 10/100/1000BASE-T/SFP ports + 4 10G SFP+ ports, L2 Management Switch - Core Switch |
| 390 | Supply, installation, testing and commissioning of 8 port- Edge PoE switch |
| 391 | Supply, installation, testing and commissioning of 24 port- Edge PoE switch |
| 392 | Supply, installation, testing and commissioning of Patch Panel UTP Keystone- 24 Port- Fully loaded (Cat 5e,Cat 6 & Cat 6 A ) |
| 393 | Supply and installation of Cat 6 UTP patch cord, 1 mtr |
| 394 | Supply, installation, testing and commissioning of Server PC, Intel i7 processor, 24 inch LED monitor, Gigabit LAN port, USB port, 8GB DDR3 RAM,1TB HDD,1GB dual graphic card, 100/1000 LAN ports, optical mouse, Keyboard, DVD Writer. Genuine Win 8.1 Pro - Down grade to Win 7 professional, 24 inch LED monitor |
| 395 | Supply, installation, testing and commissioning of Professional Joystick designed for Surveillance application as compatible with the above mentioned system. UL+CE+FCC certification minimum. |
| 396 | Supply, installation, testing and commissioning of Surveillance/ ESATA compatible Hard Disk of 4TB capacity to achieve the total storage for the NVR server |
| 397 | Supply, Installation, Testing & Commissioning of 42 inch full HD LED monitor with resolution 1920X1080 pixel including wall mounting accessories (location: security room & central control room).Material shall be UL/CE listed |
| 398 | Supply and installation of wall mounted 22U rackincluding cable manager, power supply units etc.to accommodate NVR, ethernet switch patch panel etc in control rooom |
| 399 | Supply of the following sizes of Ladder Type FRP cable trays with vertical sides on both ends as per approved design and FRP supports with coupler plates spaced 300mm apart throughout the length as specified, including the cost of support hooks, fasteners, painting if required etc.( Contractor shall ensure to use corrossion free materials as support or fastening fittings) |
| 400 | 150mm(150x100x25) |
| 401 | 300mm(300x100x25) |
| 402 | PA SYSTEM: Supply, installation, testing & commissioning of column speaker6 watts |
| 403 | Supply, installation, testing & commissioning of 6 watts ceiling speakers |
| 404 | Supply, installation, testing & commissioning of voice alarm call Station with all cables and accessories |
| 405 | Supply, installation, testing & commissioning ofvoice alarm keypad - Extension to voice alarm call station with all cables and accessories |
| 406 | Supply, installation, testing & commissioning of voice alarm controller with all cables and accessories |
| 407 | Supply, installation, testing & commissioning of voice alarm router with all cables and accessories |
| 408 | Supply, installation, testing & commissioning of 480 W Booster Amplifier with all cables and accessories |
| 409 | Supply, installation, testing & commissioning of DVD/MP3Player for audio playback only |
| 410 | Supply, Installation, Testing & Commissioning of Paging Microphone, goose neck type |
| 411 | Supply, laying and termination ofShielded Cat6 cable with all necessary accessories |
| 412 | Supply, laying and termination of2 Core x 1.5Sq.mm ArmouredAl.Mylar Screened FRLS Twin Twisted PVC Insulated cable along with all accessories. Accessories include cable glands, locknuts,saddle clips, cable tie & other hardwares to achieve cable termination and installation. Cable shall be terminated in speakers and amplifiers |
| 413 | Supply, installation, testing & commissioning of standard AV rack with 600mm Width, 800 mm Outer Depthand 36U Height |
| 414 | DATA SYSTEM: Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc as required. |
| 415 | RJ 45 socket |
| 416 | Supply and installation of Cat-6 shuttered 24 port patch panel |
| 417 | SITC of24 portunmanaged ethernet switch |
| 418 | Supply and installation of 9U rack withFront glass door, Rear Perforated door with handle Lock & key. Front/Rear 19\" mounting angles, top, bottom open, RAL 9005 with all other accessories |
| 419 | AX3600 WIFI6 Dual Band Multi Band Multi Gigabt Ceiling Mount Access Point / EAP660HD |
| 420 | Supply of the following sizes of Ladder Type FRP cable trays with vertical sides on both ends as per approved design and FRP supports with coupler plates spaced 300mm apart throughout the length as specified, including the cost of support hooks, fasteners, painting if required etc.( Contractor shall ensure to use corrossion free materials as support or fastening fittings) |
| 421 | 150mm(150x100x25) |
| 422 | 300mm(300x100x25) |
| 423 | TELEPHONE SYSTEM: Supply,laying and termination of 20 pair telephone cable, 0.5mm copper PVC insulated,unarmoured telephone cable drawn in the existing cable tray |
| 424 | Supply,laying and termination of 20 pair telephone terminal block housed in engineering plastic box with transparent hinged door |
| 425 | Supply,laying and termination of 10 pair telephone cable, 0.5mm copper PVC insulated,unarmoured telephone cable drawn in the existing cable tray |
| 426 | Supply,laying and termination of 10 pair telephone terminal block housed in engineering plastic box with transparent hinged door |
| 427 | Supply,installation,testring and commisioning of EPABX with the following specifications: 1.208 Analog Extensions with CLI Expandable to 512Ports2. 08 Port Analog trunk with CLI and Power Failure Transfer and with Protection modules.3. 02 PRI.4. 02 nos Operator Console with 30 Direct selection Keys each. 5. 08 Port Voice Guidance to announce Extension Busy status, Wake up call announcement and other important telephone features,Auto Attendant facility for Welcome message announcement.6. 02Nos -500 pair MDF(wall mountable)7. 01 No. Call Billing and monitoring Software.8. Charger/UPS with Batteries for backup of 1 hour. |
| 428 | Supply of the following sizes of Ladder Type FRP cable trays with vertical sides on both ends as per approved design and FRP supports with coupler plates spaced 300mm apart throughout the length as specified, including the cost of support hooks, fasteners, painting if required etc.( Contractor shall ensure to use corrossion free materials as support or fastening fittings) |
| 429 | 150mm(150x100x25) |
| 430 | 300mm(300x100x25) |
| 431 | NURSE CALLING SYSTEM: Supply, Installation, Testing & Commissioning of Patient Handsets - type with wired console unit |
| 432 | Supply, Installation, Testing & Commissioning of Toilet Pull Cords with all the necessary accessories for the installation. |
| 433 | Supply, Installation, Testing & Commissioning of Light Modules with all the necessary accessories for the installation. |
| 434 | Supply, Installation, Testing & Commissioning of Nurse Station Terminals with all the necessary accessories for the installation. |
| 435 | Supply, Installation, Testing & Commissioning ofsystem switch communiction accessories |
| 436 | Supply, Installation, Testing & Commissioning ofmanagement software alongwith workstation |
| 437 | QUEUE MANAGEMENT SYSTEM: SITC of Queue Management System Consisting of multi function queue ticket printer with touch screen kiosk type diplay , Voice Unit & Customer Identification devices, High Resolution GUI display in multi languages, support wireless networks, durable printer, supports alpha numeric numbering system |
| 438 | Display system with 24\" LCD Monitor, with audio speaker arrangement, HDMI Cabling |
| 439 | Workstation counters |
| 440 | Browsers/ Softwares and inclusive of testing, commissioning and training to treasury officers for Queue management system by OEM.( Necessary softwares& hardwares required for the effective functioing of QMS) |
| 441 | LIFT |
| 442 | 20BED LIFTEquipement Details : Machine Roomless - GearlessNo. of Unit : One Controller Type : Micro Processor Based VVVF Capacity in Kgs/Persons : 1360Kg/20PSpeed in MPM : 60mpm/1.0mps Door Opening Type :Centre Opening Sliding Door Operation : Simplex No.of Stops : 4 (G,1,2,T) No.of Openings : 4 (G,1,2,T) Storey Served Front : 4 (G,1,2,T)Travel (mm) : 12700mm Hoistway Size (mm) : 2400 (w) x 3000 (d)Cabin Dimemnsions (WxDxH) (mm) : 1300x2400x2350 Pit Depth (mm) : 1500 Overhead (mm) : 4250Entrance Dimensions (mm) : 1200x2100 Ceiling : SS Honeycomb finish with LED Downlight Car Front/Rear/Side Panel : SS Honeycomb finishHandrail : 38mm dia Car Doors : SS Honeycomb finishCar Flooring : Vinyl TileFloor Thickness : 1.5mm Thick Vinyl TileCar Sill : Extruded Hard AluminiumEntrance Frame/Landing Doors : SS Honeycomb finish |
| 443 | DUMBWAITER |
| 444 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand Cast Iron P or S trap, 10 litter low level white P.V.C.flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever require:17.1.1White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 445 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : |
| 446 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixerMake:Jaquar, Kohler, Grohe, Cera high end series. |
| 447 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:17.7.9White Vitreous China Surgeon Type wash basin of size 660x460 mm with single 15 mm C P. brass pillar taps with elbow operated levers ISI marked |
| 448 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cisternMake: Jaquar, Kohler, Grohe, Cera high end series. |
| 449 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:17.7.7White Vitreous China Flat back wash basin size 450x300 mm with single 15 mm C.P. brass pillar tap |
| 450 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 451 | Providingandfixingstainlesssteeltoiletpaperholder. Make:Jaquar,Kohler, Grohe, Cera high end series. |
| 452 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore.Make:Jaquar, Kohler, Grohe, Cera high end series. |
| 453 | 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms |
| 454 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 455 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board510x1040 mm bowl depth 250 mmMake: Jayana, Nirali, Carysil high end series. |
| 456 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:17.7.10Stainless Steel AISI - 304 ( 18/8/) Round basin 405x355 mm with single 15 mm C.P. brass pillar tap. |
| 457 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore Make: Jaquar, Kohler, Grohe, Cera high end series. |
| 458 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC SDR 11) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall (Above ceiling and Ducts) |
| 459 | 15 mm nominal outer dia Pipes |
| 460 | 20 mm nominal outer dia Pipes |
| 461 | 25 mm nominal outer dia Pipes |
| 462 | 32 mm nominal outer dia Pipes |
| 463 | 40 mm nominal outer dia Pipes |
| 464 | 50 mm nominal outer dia Pipes |
| 465 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.Make: Astral, Supreme, Finolex, Prince |
| 466 | 20 mm nominal outer dia Pipes |
| 467 | 25 mm nominal outer dia Pipes |
| 468 | ProvidingandsupplyingISImarkCID/FButterflyValvesasperIS:13095 (Latest Edition) of PN 10 and 50 mm diameter including all taxes, insurance, transportation,freightcharges,octroi,inspectioncharges,loading, unloading, conveyance to departmental stores, stacking etc. complete. |
| 469 | ProvidingandsupplyingISImarkCID/FButterflyValvesasperIS:13095 (Latest Edition) of PN 10 and 65 mm diameter including all taxes, insurance, transportation,freightcharges,octroi,inspectioncharges,loading, unloading, conveyance to departmental stores, stacking etc. complete. |
| 470 | ProvidingandsupplyingISImarkCID/FButterflyValvesasperIS:13095 (Latest Edition) of PN 10 and 80 mm diameter including all taxes, insurance, transportation,freightcharges,octroi,inspectioncharges,loading, unloading, conveyance to departmental stores, stacking etc. complete. |
| 471 | ProvidingandsupplyingISImarkCID/FButterflyValvesasperIS:13095 (Latest Edition) of PN 10 and 100 mm diameter including all taxes, insurance, transportation,freightcharges,octroi,inspectioncharges,loading, unloading, conveyance to departmental stores, stacking etc. complete. |
| 472 | Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.Y- Strainer of Ductile of 50 mm dia |
| 473 | Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.Y- Strainer of Ductile of 65 mm dia |
| 474 | Providing and fixing Gun metal check or non-return fullway wheel valve.(E) 40mm dia. |
| 475 | Providing and fixing Gun metal check or non-return fullway wheel valve.(E) 50mm dia. |
| 476 | Excavation for foundation/utility services upto 1.5 m depth including sorting out and stackingofusefulmaterialsand disposingoffthe excavated stuff with all lead and lift.(E)HardRock |
| 477 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm. in depth consolidating each depositedlayer by ramming and watering. (Ramping by manual ormechanical means) |
| 478 | Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with frame of 300mm x 300mm size (inside) with standardweight.(i)Squaremouthtraps.(B)150mmx100mmsizePorR type(make-Local ) |
| 479 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin counter top type 550x420mm with a 15 mm CP Brass single hole basin mixer. Make:Jaquar, Kohler, Grohe, Cera high end series. |
| 480 | Fixing, Testing and Commissioning at site Wall Mounting type water closet with P trap & its all fittings like rag bolts, solid plastic Seat cover etccomplete including cutting and making good the walls and floors wherever required,Concealed flushing cisternwith brass screws,nuts , and washers complete including cutting and making good the walls and floors wherever requiredEtc complete.Queo - (Zelos Neo+CC Sisma)/ KOHLER ESCALE K16817IN-SS-0, OR Equ. |
| 481 | Providing, Fixing, Commissioning at site Urinal Partition with Curved shaped frosted glass fixing with brass screws,nuts , and washers complete including cutting and making good the walls and floors wherever requiredEtc complete. 900x450x10 mm tk. Make: Jaquar 1110uc/ equ. |
| 482 | Providingandfixingofgrabbars300mmStainlesssteelinphysically disabledtoiletincludingallnecessaryfitting,SSScrews&Accessories etc.Complted in all manners and satisfied to of EIC. complete. Make: Jaquar,Kohler, Grohe, Hindware, Cera high end series. |
| 483 | Providing and fixing of grab bars Vertical Swing 18-8 S, type-304, 18-gauge (1mm) stainless steel tubing with satin-finish. 1–1/4 (25mm) outside diameterwallmountedinphysicallydisabledtoiletincludingallnecessary fitting, SS Screws & Accessories etc.Complted in all manners and satisfied to of EIC.complete. Make: Jaquar, Kohler, Grohe, Hindware, Cera high end series. |
| 484 | Providing, Fixing, Testing and Commissioning at site ablution Health Spray Faucet with wall hook and 1.2 mtr. Chrome plated PVC hose pipe, etc. complete in all respects. Queo - Addons/Kohler/Grohe/jaquar |
| 485 | Providing, Fixing CP Robe hook: Queo - / KOHLER/Grohe ,jaquar OR Equ. |
| 486 | Supplying,Fixing, Testing, and commissioningSink tapwall mounted/floor mounted with swivel casted spout and wall flange, trending cutting and making good the walls whatever required etc. complete Queo - Allamoda/jaquar/Kohler/Grohe |
| 487 | Providing and Fixing of Stainless SteelHand Dryer with all required connections and following specifications. Weld-free cover fixed to the base with two safety screws and lock withspecial speedflow key. Aluminium base. Includessilent-blockstodamp mechanicalvibrations.Fireresistant plastic UL 94-V0 fan scroll. High-speed motor with safety thermal cut-off.The motor revolutionscanbeadjustedmanuallybythepotentiometer.•Aluminium centrifugaldoubleasymmetricalinletfanwheel.Disconnectsautomatically after60secondsofcontinuoususe.Electronicinfrareddetectionsensor. Adjustabledetectionbypotentiometer(5-25cm).Ultra-flat:10cmdeep (complieswithADAregulations).complete.Make:Jaquar,Kohler,Grohe, Hindware, Cera high end series. |
| 488 | Providing and fixing wash basin with 4 Faucets 16 SWG SS 304 HL- Finish Top, with 16 SWG SS 304 leg channel to support legs for increased hygiene and strength compared to angle framework; 40X40 mm SS 304 16 SWG square tube legs; Height adjustable high quality nylon bullet feet; SS 304 custom made sink.SS 304 20SWG HL-finish 25x25mm square tubular cross supports.size-250*55*35 cm |
| 489 | Providing and fixing Gyser 20 Ltr with flexible connectionfittings arrangement etc. complete of approved quality and make, including cost and conveyance of all materials, labour charges, lead, lift, etc. complete, as per direction of the Engineer-in-Charge at all levels. |
| 490 | Supplying, Fixing, testing and commissioning at site in positionuPVC pipe -6kg/cm2) (IS:4985)Solvent Welded fittings with bosses where required e.g. tees, bends, coupling, door bends, junctions, cowls, door TEE , Door Elboe where ever required etc.,complete. (Soil & Waste in Shaft) Make: Astral/Supreme/Ajay |
| 491 | 110 mm O.D. (6Kgf/cm2 IS:4985) |
| 492 | 75 mm O.D.(6Kgf/cm2 IS:4985) |
| 493 | 63 mm O.D( 4Kgf/cm2) Vent pipe in shaft |
| 494 | Providing, Fixing, testing and commissioning at site in position uPVC pipe( IS : 4985 ) With Rubber Ring or Solvent Welded fittings with bosses where required e.g. tees, bends, coupling, etc. complete. (For Rain water pipes in shaft & Ceiling) Make: Astral/Supreme/Ajay |
| 495 | 110 mm O.D( 4Kgf/cm2)) Rain water pipe in shaft |
| 496 | Supplying, Fixing, testing and commissioning at site in position u PVC pipe of 6Kgf/cm2including PVC fittings with bosses where required e.g. tees, bends,door TEE , Door Elboe where ever requiredcoupling and adapters and jointing with adhesive approved by fitting manufactures including cutting and making good the walls and floors or surface mounted with clamps as required at site universal clamps & anchor fasteners(8mm) , threaded rod(8mm),nuts ,washers, wherever required etc. complete.Make: Astral/Supreme/Ajay |
| 497 | 50 mm O.D. (6Kgf/cm2 (IS:4985) |
| 498 | 75 mm O.D. (6Kgf/cm2 (IS:4985) |
| 499 | 110mm O.D (6Kgf/cm2 (IS:4985) |
| 500 | 32 mm O.D. (8Kgf/cm2 (IS:4985) for sunken spout |
| 501 | Supplying, Fixing, testing and commissioning at site in position Deep Seal UPvc fabricated Multi floor trap (4”), with suitable supporting on GI slotted rails (1.6mmthick) full threaded rod, anchor fasteners etc. complete in all respects.50/75 mm dia outlet (In Ceiling)Astral/Supreme/Ajay |
| 502 | Supplying,Fixing, testing and commissioning at site in position UPvc fabricated Multi floor trap (7”),with 50/75 mm dia outlet (In Sunken slab & floor raising areas)Astral/Supreme/Ajay |
| 503 | Supplying,Fixing, Testing and commissioning at site in position 150x150mm square C.P cast brass or stainless steel anti cockroach grating cover ss (304) of matching size of UPvc fabricated floor trap / multi inlet trap complete in all respects. Chilly/Eligna/ |
| 504 | Supplying,Fixing, Testing and commissioning at site in position 150x150mm square C.P cast brass or stainless steel sealed grating cover ss (304) of matching size of UPvc fabricated floor trap / multi inlet trap complete in all respects. Chilly/Eligna/ in common toilets |
| 505 | Supplying,Fixing, testing at site in position 160mm dia square /circular grating Terrace rain water outlet(Cast Iron)(for 110mm dia pipe) |
| 506 | Supplying, Fixing, testing at site in position PVC Roding Eye (6kg/cm2) Complete in all respects. |
| 507 | 110 mm dia |
| 508 | 75 mm dia |
| 509 | Providing and fixing in position cowel went to pipes.(C) 100mm dia |
| 510 | Providing, Fixing at sitein position uPVC Pipes (as per ASTMD – 1785 sch-40 ) of approved make For Cold Water Supply, complete with all necessary (ASTM D – 2466/2467) fittings (elbows, unions, tees, reducers, couplings, nipples etc) (External/ Inshaft) |
| 511 | 1 ¼ “ (32mm) dia. |
| 512 | 1 1/2 “ (40mm) dia. |
| 513 | 2” (50mm) dia(External / in Shaft) |
| 514 | 2 ½” (65mm) dia(External / in Shaft) |
| 515 | Supplying,Fixing at site in position full way lever operated forged brass gate valve of brass body with forged brass hard crome plate (PN 10) of approved make with necessary MTA fittings in position as per drawings |
| 516 | ½ \"\"(15mm) dia.Globe valve |
| 517 | ¾ \"\"(20mm) dia. |
| 518 | 1” (25mm)dia |
| 519 | 1 ¼ “ (32mm) dia. |
| 520 | 1 1/2 “ (40mm) dia. |
| 521 | 2” (50mm) dia |
| 522 | Supplying, Fixing, testing and commissioning at site Puddle Flangefabricated from Upvc ASTM Grade sch-40 pipes & uPVC sheet (600 mm long) |
| 523 | 1 ½” (40mm) dia(External / in Shaft) |
| 524 | 2” (50mm) dia(External / in Shaft) |
| 525 | 2 ½” (65mm) dia(External / in Shaft) |
| 526 | 3” (80mm) dia(External / in Shaft) |
| 527 | 4” (100mm) dia(External / in Shaft) |
| 528 | 6” (150mm) dia(External / in Shaft) |
| 529 | Supplying, Fixing, testing and commissioning at site Puddle Flangefabricated from GI pipe with 6mm tk plate (600 mm long) for FIRE Tank |
| 530 | 6” (150mm) dia-GI,single side flange |
| 531 | 8” (200mm) dia-GI ,single side flange |
| 532 | Supplying and Laying of pipes and conveying to position; cleaning, laying and jointing to true lines and gradients,with proper bedding uPVC pipe of IS 4985(6kgf/cm2)including jointing the pipe as per specification, testing the pipe line after installation all per provisions of IS: 1742-1983 (Code of practice for building drainage) complete as directed by the Employer |
| 533 | 160 mm OD (6/kg/cm2) |
| 534 | Providing and supplying of Class SN8Structured Wall polyethelene Piping systems (Pipe with online/offline coupler and elastomeric sealing ring) with non-smoothExternalAnnularCorrugatedandSmoothInternalSurfaces (Double Wall) for non-pressure underground Sewerage & Drainage application as per EN:13476-3 including all local and central taxes, transportation,freightcharges,octroi,inspectioncharges,loading, unloading, conveyance to the departmental stores etc. complete.(ID 150 mmdiameter) Make: Astral, Supreme, Finolex, Prince |
| 535 | 160 mm OD (6/kg/cm2) |
| 536 | 200 mm OD (6/kg/cm2) |
| 537 | Supply, installation, testing and commissioning of percolation well (Recharge well) including all work like drilling, compressor work, gravel packing, mud slurry disposal, clay packing and including of all materials like 300mm UPVC pipe, 300mm wire screens, 300mm collar joint, accessories, gravels, sand, sand filteration module etc. Site cleaning, mud pit, mud refilling for borewell must be in the contractor\"sscope.Contractorhastomaintainthepercolationwellupto three years after installation. |
| 538 | Supply,Installation, Testing and commissioning of Clear water transfer open well submerssible pump of adiquate hp with discharge 3 lps at 20 mtr head, SS body, ss shaft with bronze impeller mounted on a single base platewith controll panel and auto level controller. 1 working+ 1 stand by |
| 539 | TERRACE DWS BOOSTER PUMP Duty Conditions of 6 lps @ 35 mtr - head(Each pump 3LPS 35 mtr Head - 2 Pump system-1 Working+1standby) Compact skid mounted Booster pumps with SS 304 casing, SS316 impeller , SS316 shaft , C I base and TEFC motorwith mechanicalseal. Pumpto be havesingle VFD logic controller. - Electriccontrol panel withlogic controller, relays, calibrated pressure switch, pressuretransmitter including cabling within panel, incorporating dry run protection, potential contacts forBMS integrating , sucton and discharge headers, pressure vessal 60 ltr capacity. |
| 540 | Supplying and fixing of Borewell /tube well submerssible pump with panel, with CIconstruction, CI impeller complete with motor, base plate, foundation bolts, nuts, pressure guage and all accessories. and working with 415V, 3ph and50 Hz frequencyalong with pump protection starter with in built level controller for automatic operation of pumpset using float switch , The panel should have LCD screen showing Voltage / Ampere, Error log, Cascading operation , Pump run status , Auto faulty pump change over, Auto- Manuel selection etc . The panel should protect the pumpsetfrom over and under voltage, over and under load, dry protection , Phase reversal protection , Single phase prevention etcincluding cost and conveyance of all materials,labour charges etc complete as directed by the Engineer-in-Charge at all levelsCapacity :7m3/hrHead : 55 m |
| 541 | Supplying and fixing of Horizontal open well SUBMERCIBLE pump(1W+1S)ug to oht, with CIconstruction, CI impeller complete with motor, base plate, foundation bolts, nuts, pressure guage and all accessories. and working with 415V, 3ph and50 Hz frequencyalong with pump protection starter with in built level controller for automatic operation of pumpset using float switch , The panel should have LCD screen showing Voltage / Ampere, Error log, Cascading operation , Pump run status , Auto faulty pump change over, Auto- Manuel selection etc . The panel should protect the pumpsetfrom over and under voltage, over and under load, dry protection , Phase reversal protection , Three phase prevention etc -Capacity :24 m3/hrHead : 32 m |
| 542 | Fixing, testing and commissioning at site Automatic Dewatering system having 2 nos (1w+1s) Vertical Bottom suction submersible pump Having CI: body / Ci: impeller / SS : shaft . Each pump should be capable to deliver 3 lps @ 8mtr , having 0.75 kw /1hp /3phase motor . A wall mounting micro controlled automatic control panel should be provided for the working of pumpset as 1w+1s in cascading operation . The control panel should have LCD screen showing Voltage , Ampere , Pump running status , error logs, faulty pump indication etc. The panel should protect the pumpset from over and under voltage , over and under load , dry run, etc . Automatic operation of pumpset should be with float switch.(deliver pipeline size : 40mm )(Basement Pit ) |
| 543 | Supply, Installation, Testing & Commissioning of 14,000 Lpd Water Treatment Plant with Reverse Osmosis Process with all mechanical work like piping,mechanical components as follows but excluding the electrical works and civil work. a) PAC offChlorine Dosing system -1nos,Pressure sand filter FRP-1 no ,Activated carbon filter FRP-1no, |
| 544 | 40 KLD Fiber reinforced tank (FRP) With Modular Membrane Bioreactor (MBR) based Sewage Treatment Plant, Design Flow KLD 60.0 LPH 2000.0 Type Fully-Automated, Design MLSS mg/L 6000.0 – 8000.0.Membrane Membrane Bioreoctor (MBR) to provide an advanced level of organic andsuspended solids removal with 0.4 Microns pore isze, provides high filtrate quality.Operating Hours h 24.0, Design Flexibility % 30 - 100 with transfer pumps, air blowers, medias, membrine, tube settlers and all connected pipe lnes and necessary power connections and cubicle control panel in all respect. 3 years operation and maintanance of Sysytem is included,OUTLET ResultsParameter Unit Outlet ValuepH - 6.5-8.5TDS mp/I <2100TSS mp/I <20BOD5 mp/I <10COD mg/I <50Total Nitrogen mp/I <5Phosphorus mp/I <5Ammonia Mp/I <5Fecal Califorms MPN/ml Less than 1000 |
| 545 | Incinerators with capacity of 150 kl per day include air pollution control equipment (e.g., fabric filters, scrubbers, electrostatic precipitators) to remove fly ash and gaseous contaminants |
| 546 | Supply, installation, testing and commissioning of 1200 LPD Solar Water Heater with Heatingcoile Control panel with necessary controls, and other standard accessories as instructed by S-I-C. |
| 547 | Supply, installation, testing and commissioning of Recirculation pump, Inline pump with SS body with 2lps @18 meter head with standard solinoid valves, necessary piping and other standard accessories as instructed by S-I-C. |
| 548 | Providing,fixing,jointingandtesting,heavyquality caststeel /Brass Air Release Valve designed ofapproved make, including flanges / unions, nuts, bolts, washers, etc. complete, as per I.S 5212 approved by the Engineer-in-charge for water supply lines of the following nominal bore (NB)size: 20mm diameter. Make:ZOLOTO/VTC/SANT |
| 549 | Constructing Brick masonry road Inspection chamber 450mm x 450mm x 775mm with horizontal grating complete.C.M.1:6.Foundation concrete150 mm thick in C. C.1:4:8oftrap metalsize 25mm to40mm thick, inside cement plaster in C. M. 1:3 and cement pointing outside in C. M. 1:3 and ms gratings on top. Upto 1 Mt. depth from G. L. to pipe invert level incl. complete civil works but excl. cost of excavation and refilling, with cast in situ RCC slab in one single piece with fixing of CI-MH Frame and cover (incl cost of CI-MH Frame and cover) with 23 mm thick brick masonry wall in C.M.1:6.With precastslab in two parts 15mm. for rain water/storm water drainage |
| 550 | Construction of Manhole chambers(Inspection chambers) 600mm X 600 mm and depth 1.0 m in brickorbelastonemasonry,locallyavailableinC.M.1:6.Foundation concrete150 mm thick in C. C.1:4:8oftrap metalsize 25mm to40mm thick, inside cement plaster in C. M. 1:3 and cement pointing outside in C. M. 1:3 and top cover of precast RCC slab 100 mm thick (with key hole in two parts, each with handles or MS Bar etc. complete as given size) Upto 1 Mt. depth from G. L. to pipe invert level incl. complete civil works but excl. cost of excavation and refilling, with cast in situ RCC slab in one single piece with fixing of CI-MH Frame and cover (incl. cost of CI-MH Frame and cover) with 23 mm thick brick masonry wall in C.M.1:6.With precastslab in two parts 15mm. |
| 551 | Extra over items above for every additional depth of 0.1M. of part thereof beyond 450mm depth for Brick masonry chamber.(i) |
| 552 | ProvidingandfixingC.I.coverwithframe(Medium duty)600x600mm , total weight of cover and frame to be not less than 108kgFOR SUMP TANKS |
| 553 | ProvidingandfixingC.I.coverwithframe(Light duty)600x600mm , total weight of cover and frame to be not less than 23 kg for OHT |
| 554 | Supply, installation,testing and commissioning of Grease Chamber round type havingcapacity of 400-750 litter. The separator for greasy wastewater is suitable for installation in the ground and comes without metallic components in the tank. The collecting tank made of permanently resistant polymer (PE) is equipped with an integrated sludge trap and has a rounded base for fast and clean disposal. Access for cleaning and maintenance work is possible via one or several service access covers. A direct disposal pipe socket shall be available for odour-reduced manual disposal. A load distribution slab must be installed on site for load class D. The reinforcement shall be provided as per OEM specification . installation depth 550-900 mm,net weight not less than130 kgand gross wight not leass than 137 kg |
| 555 | Supply and fixing ofDRAINAGE GRATING WITHTROUGH, 30x30x8+10• Trough using 1 mm thick 304grade #4 stainless steel• Grating using 2 mm thick 304grade #4 stainless steel |
| 556 | Supply and fixing ofDRAINAGE GRATING WITHTROUGH, 60x30x8+10• Trough using 1 mm thick 304grade #4 stainless steel• Grating using 2 mm thick 304grade #4 stainless steel |
| 557 | Providing, Supply, installation,testing and commissioning of UPVC Oil Wastesystem conforming to DIN-EN-12056 & DIN-1986-100 fittings (moulded as well as fabricated) like bends, tees, Y-tees, crosses, boss connections, access pieces, saddle pieces, cleanouts, adaptors for connections to other materials, plugs, reducers, cowls, offSet and other specials. Jointing shall be done with pushfit EPDM ring jointing technique in general. Solvent cement joints may be provided for fittings and specials which are not manufactured with pushfit rubber joints. Pipes may be laid / fixed in sunken floors, under slung from ceiling. The pipes laid in sunken floor shall be encased with 75 mm thick cement concrete (1:2:4) all around. The installation shall be complete in all respects including cutting chases / holes in walls, slabs and making good the same as per specifications. |
| 558 | 75mm Dia |
| 559 | 110mm Dia |
| 560 | FIRE HYDRANT SYSTEM: Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :Make: Safeguard, Minimax, New Age |
| 561 | Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :Make: Safeguard, Minimax, New Age. Stainless Steel (Grade 304) |
| 562 | Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :Make: Safeguard, Safefire, Minimax, New Age |
| 563 | Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 1258520 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall.Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.and tested to 1.2 MPA( 12 Bar pressure) installation brackets, complete in all respects including all accessories as required for complete installation. INLET PIPE CONNECTION FROM RISING MAINS TO HOSE REEL SHALL BE PROVIDED WITH GI HEAVY CLASS PIPES WITH UNIONS OR WITH READY MADE TYPE FLEXIBLE RUBBER HOSE IN STANDARD LENGTH, HYDRAULICALLY FITTED END CONNECTIONS ETC .Make: Monsher, Minimax, New Age |
| 564 | Supplying and fixing of 4 Way fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :Make: Safeguard, Safefire, Minimax, New Age |
| 565 | Supplying and fixing of 2 Way fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :Make: Safeguard, Safefire, Minimax, New Age |
| 566 | Providing, laying, testing & commissioning of \"B\" class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as requiredNote : Pipes up to and 50 mm dia shall be socket welded with DI fittings. For pipes inside the Fire pump room |
| 567 | 25 mm dia |
| 568 | 80mm dia |
| 569 | 100 mm dia |
| 570 | 150 mm dia |
| 571 | 200 mm dia |
| 572 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : Make : Leader/ Audco/ Zoloto |
| 573 | 80 mm dia |
| 574 | 100 mm dia |
| 575 | 150 mm dia |
| 576 | 200 mm dia |
| 577 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : Make : Leader/ Audco/ Zoloto |
| 578 | 150 mm dia |
| 579 | 100 mm dia |
| 580 | 80 mm dia |
| 581 | Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.Make : Leader/ Audco/ Zoloto |
| 582 | 100 mm dia |
| 583 | 200 mm dia |
| 584 | Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required. Set |
| 585 | Supply, installation, testing and commissioning of Brass Air release valve, size 25mm with threaded inlet & provided with ball type float complete with all accessories required for complete installation. Make : Leader/ Audco/ Zoloto |
| 586 | Supply, installation, testing and commissioning of industrial type pressure switch having 1/4\" BSP(F) connection IP:32 enclosure protection, phosphor bronze bellows as sensing element, SDPT contact system, switch rating 6A Inductive/lOA resistive 380 V AC, 0.2A Inductive/10A resistive 250V DC suit with ball valve etc. complete as required. Make: Infoss/ |
| 587 | Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to soundcontinuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required : 150mm Dia |
| 588 | FIRE PUMPS, & ACCESSORIES: Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in allrespects, as required :(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-\"F\" insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads.: 1620 lpm at 56 m Head Set. Make : Kirloskar, Mather & Platt India Limited |
| 589 | Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-\"F\" insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. Pump –Pump Casing : C.I, Impeller- Bronze impeller. 180 lpm at 56 m Head Set. Make : Kirloskar, Mather & Platt India Limited |
| 590 | Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 voltselectric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. Suitable reinforced cement concrete pump foundation including cushy foot mounting, foundation bolts, washers as required. Engine panel, Sealed maintenance free batteries of 24 V, 88 AH, Exhaust pipe of required length with asbestos lagging, muffler, Day oil tank of 400 lts with first charge and manual oil pump set. No. of stage preferred - Single / Double, |
| 591 | The pump shall be of the following specifications: Discharge - 1620 lpm, Head - 56 m, Speed RPM -1450, Mover - Diesel engine driven, Material of construction, a) Impeller - Bronze, b) Casing - C.I., c) Shaft & Shaft Sleeve - SS-410, d) Bearing - Grease Lubicated, e) Seal & Make - Mechanical, Type of pump - End Suction.1620 lpm at 56 m Head Set Make : Kirloskar, Mather & Platt India Limited |
| 592 | Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, inter connection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required : |
| 593 | Details of requirements given in specs. INCOMING 250A, 50kA 4 Pole MCCB, Ics=100% Icu rating Digital Voltmeter 0-500V with selector switch Digital Ammeter (0-250 A) with selector swtich & CTs etc.LED type RYB phase indicating lamps, ON, OFF, tripindicating lamps Set of Copper Bus Bar 300A OUTGOING( Note : All outgoing feeders for pumps should have digital Ammeter with selector switches, and LED type ON, OFF, trip indicating lamps)Main Fire Pump125 A, 50kA TPN MCCB, Ics=100% Icu, with fully automatic Star/Delta starter suitable for 60 HP pump with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation.Jockey Pump63 A, 50kA TPN MCCB, Ics=100% Icu, with suitable HP fully automatic Star/Delta starter with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation. DIESEL ENGINE CONTROLControl for diesel engine comprising -Automatic/Manual selctor switch & 3 attempts starting device, timers and relays as required, push buttons, start/stop in manual modeIndicating lamp for high/ Low Lub. Oil pressure, High Water Temp and Engine on indication Battery charger suitbale for 12V/24 V DC with boost and trickle selector switch, 0-30 V DC volt meter, and 0-20 A DC Ammeter. All standard relays and accessories for automatic operation of diesel engine System Controller Designing, Supply, Installation, Testing andcommissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specificationconsisting of relays, timers. Sensors, annunciation window for fault indication, complete as perspecificationFollowing provisions to be made in the fire panel: Facility for mode selection ie auto or manual test & local/remote.Protection failure & control cabling. Panel shall be interlocked in such a way when fire pump starts on pressure drop in the header, supply to working chiller A/c panel is disconnected. Remote indication of ON/OFF/TRIP shall be provided through potential free contact. |
| 594 | AUTOMATIC SPRINKLER SYSTEM: Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : working pressure 175 PSI (UL/FM approved)as required for complete installation as required.Make: Tyco/Viking/Sharp |
| 595 | Pendent Type bronze finish with C.P. brass rossett flange |
| 596 | Up right Sprinkler |
| 597 | Extended Coverage Side wall type sprinkler( apartment Inside) |
| 598 | Pre-assembled, ready to install,flexible connectors, stainless steel hose lengths: 1000mm,Mounting bracket , Maximum Working Pressure: 200 psi , Minimum Bend Radius UL Listed /FM Approved |
| 599 | Providing and fixing GI heavy duty \"B\" class (IS: 1239 Part-1) including cutting, welding etc. and providing all fittings viz. Flanges. Bends,Tees, Elbow, Reducers, Clamps. Hangers etc. including cutting holes and chases in brick or RCC walls/slabs and making good the same to the approval of engineer/consultant complete including painting with one coat of primer and two or more coats of enamel paint of approved make and shade including steel work, GI pipe sleeve of suitable higher size shall be provided wherever the pipes are crossing the walls / floors and sealing the sleeves with glass wool in between & fire sealant compound at either end all as per Project Manager’s requirements including cutting holes and chases in brick, RCC work and making good the same to original conditions complete in all respects. Note : Pipes up to and 50 mm dia shall be socket welded with DI fittings. |
| 600 | 25 mm dia |
| 601 | 32 mm dia |
| 602 | 40 mm dia |
| 603 | 50 mm dia |
| 604 | 65 mm dia |
| 605 | 80 mm dia |
| 606 | 100 mm dia |
| 607 | Supply, installation, testing and commissioning of electrically operated water flow switches (Vane type) dia 65 mm including tamper switch and accessories, complete with tap off socket arrangement as required, with potential free contact with 2 Nos. NO/NC including all accessories as required for complete installation. HD/ Honeywel |
| 608 | In 100mm line |
| 609 | Supply, Installation, Testing and Commissioning of Fire alarm control panel capable of handling 99 devices / detectors per loop to meet the NFPA Standards and UL approvals. 2 loop Panel should be expandable, with a battery backup in normal condition and in alarm condition. The panel should be expandable. Make: Honeywell/Edward/Essar/Cooper |
| 610 | Supply, Installation, Testing and Commissioning of Intelligent Addressable Heat Detector with base. The detector shall be suitable for both rate of rise and fixed temperature. Make: Honeywell/Edward/Essar/Cooper |
| 611 | Supply, Installation, Testing and Commissioning of Intelligent Addressable Multi Sensor with optical smoke element and thermal element. Make: Honeywell/Edward/Essar/Cooper |
| 612 | Supplying, installation, testing & commissioning response indicator on surface/ recess MS box having two LEDs metallic cover complete with all connections etc. as required |
| 613 | Supply, Installation, Testing and Commissioning of analogue addressable type Manual pull station at indicated locations with necessary termination as per the specifications and full ready for operation. Make: Honeywell/Edward/Essar/Cooper |
| 614 | Supply, Installation, Testing and Commissioning of addressable sounder at different locations complete with all fixing accessories.Make: Honeywell/Edward/Essar/Cooper |
| 615 | Supply and laying of 2C X 1.5 Sqmm Armoured copper conductor cable FRLS with all necessary saddles and other accessories. Make: Finolex/Polycab/Havells/KEA |
| 616 | Supply, Installation, Testing and Commissioning ofShort Circuit Isolator Module for isolating the affected segment of the circuit, allowing the remaining devices to continue operation.Make: Finolex/Havells/Polycab |
| 617 | 10 zone control panel for fire alarm system with following:- 250 Watt amplifier racks suitable for operation on 230V AC/24V DC supply conforming to IEC-268-3 complete with all accessories as required 2 Nos. (one to act as standby) Talk back master station with LED PTT (Press to talk) push button for operation on 230V AC/24 V DC supply conforming to IEC-268 for simplex mode of operation/communication suitable for 20 Nos.talk back unit 1 set.Annoucement control desk suitable for selection of different zones selectively and ON ALL CALL switch with visual indication etc., complete as required 1 Set. Amplifier change over switch for inter changing amplifier 1 No. Monitor panel for loudspeaker complete output selector ON/OFF switch, fuse visual indications etc. complete as required 1 No.Gooseneck microphone with stand and ON/OFFswitch 1 No. Mains ON/OFF switch, fuse indication lamps,DC and AC voltMetres & Ammetres terminal blocks etc. complete as required 1 Set. Battery charger trickle cum boost to take completeload of fire alarm & PA system complete with all accessories including providing & fixing of 2 nos.12 volt, 60 AH each sealed maintenance free batteries |
| 618 | Supplying, installation, testing & commissioning talk back slave station in surface/ recess suitable for operation on simplex mode complete with P.T.T. knob & speaker/ microphone enclosed in a M.S.(16 SWG)/ ABS box with break glass in front etc. complete as required. |
| 619 | Supply, installation testing and commissioning of20mm. PVC Rigid Conduits conforming to IS and specification,on walls /ceiling / floor etc. complete with all accessories like junction boxes, collars, bends etc. Make: ISI Marked |
| 620 | Supply, install, test and commission 2C x 1.0 mm PVC cable. Make: Finolex/Havells/Polycab |
| 621 | Supply and installation of Weather proof Outdoor type hose cabinets fabricated from 14 SWG M.S. sheet with full glass door with locking arrangement (Water Proof), suitable to accommodate 2 nos.15 M long hose and 1 No branch pipe. Glass will be transparent Acrylic - 3mm thick. The cabinet shall be painted with coat of P O Red paint from outside and white paint from inside including all accessories as required for complete installation.(size shall be such that the above all items can be accommodated). (Double door type) as per industrial standards |
| 622 | Supplying, laying, fitting and fixing , testing and commissioning of under ground GI heavy duty \"C\" class pipe confirming to IS 1239 The pipes shall have anti-corrosive wrapping coating and a wrapping treatment with pipe coat 4 mm thickness, after applying one or more coats of Asphalt primer. Rates shall include cutting, welding etc. bends, elbows reducers suitable for pipe joints, clamps and all other accessories including excavation of earth to sufficient depth to install the pipes, the pipes buried in ground excavation and refilling etc.as per the specification and as required complete as required for complete installation etc. including cutting holes in RCC walls/slabs and making good the same adequately supported on rigid supports duly painted as required complete in all respect including allup to building rising mains and for yard hydrants , |
| 623 | 100 mm dia |
| 624 | 80 mm dia |
| 625 | Supply & installation of Pressure Gauge with 0-300 psi (0-21Kg/Sq.CM) range white background, black graduation scale with dual reading in Kg/Sq.CM & PSI, 1/4\" BSPT bottom entry 100 MM dial, PHOSPHOROUS BRONZE bourden tube, brass moving parts, polished stainless steel case with positive seal against weather, moisture & dust, hardened glass, glycerine filled type with syphon tube and isolation cock,Make: Fiebig / H guru |
| 626 | Providing & fixing double flanged flexicon rubber expansion joint with unit control of standard length as per manufacturers specifications suitable for working pressure rated (PN16) and test pressure to be 150 % rated pressure ofincluding rubber gaskets, flanges, nuts, bolts and washers complete as required |
| 627 | 100 mm dia |
| 628 | 80 mm dia |
| 629 | Supply and fixing Co2 type Fire Extinguisher of capacity 4.5 kg filled with Co2 Gas with control discharge mechanism ( squeeze grip type) fitted with Bend and Horn applicable on Class B and C class of fire. Manufactured and marked to IS 15683 with ISI marking and cylinders having the approval of Chief Controller of Explosives, and including all accessories as required for complete installation. |
| 630 | Supply and fixing of dry chemical powder type (DCP) fire extinguishers (ABC Type) of 4 Kg capacity, Pressurized with nitrogen, mfg. to IS:15683 with ISI mark fitted with pressure gauge, GM cap nozzle complete with initial charges and installation brackets and screws with ISI marks etc. complete as approved and instructed by the engineer in charge including all accessories as required for complete installation.. |
| 631 | Supply and fixing of Modular type automatic extinguishers with Clean Agent Gas Fire Extinguisher mainly consist of MIG welded M.S. body 2 mm CRC Sheet upper part of which is fitted with adapter or Flange for fixing on ceiling wall. And below part fixed automatic release Nozzle based on Sprinkler technology unlike the Sprinkler Nozzle is gas tight the release temperature is adjusted with sprinkler imported bulb set at 57 0 C, or 680 C or special temperatures according to specific requirements and imported pressure gauge fitted for insta nt verification of reliability of every unit. |
| 632 | Supply and fixing emergency exit light fixture with battery back up unit, LED Lamps, indicating Fire Exit, recess / mounted type. 24hrs x 7days working conditional. |
| 633 | Supplying andinstalling of in position the various type of sign boards made out of 3mm thick \"Opaque\" PVC foam board with computer cut, PVC Non-reflective self adhesive vinyl painted foam board, complete with mirror fasteners. Size : 60cm x 15cm |
| 634 | Supplying,Fixing at site in position full way lever operated forged brass Ball valve of brass body with forged brass hard crome plate (PN 10) of approved make with necessary MTA fittings in position as per drawings |
| 635 | 1” (25mm)dia |
| 636 | 2” (50mm)dia |
| 637 | Supplying,Fixing at site in position full-3way lever operated forged brass Ball valve with sight viewb glass (test and drain ) of brass body with forged brass hard crome plate (PN 10) of approved make with necessary MTA fittings in position as per drawings |
| 638 | 2” (50mm)dia |
| 639 | VRF/VRV UNITS: Supply, Installation ,testing and commissioning of the following minimum capacityAir-cooled VRF (Variable Refrigerant Flow) Outdoor unit with variable speed inverter driven multiple compressors complete with suitable capacity drive motors conforming to IE3 as per IS 12615, air cooled condenser, R410A refrigerant, oil separator, with all accessories, and safety devices like thermal protector, pressure relief valve, high-low pressure cut off etc . Necessary structural supports, ODU vibration isolators shall be considered . Equipment shall be suitable for 3 phase, 415 V, 50Hz supply along withsuitably rated starter panel & associated accessories, suitable interconnecting control cabling between IDUs, ODUs ,power cabling between isolator and single/multiple outdoor units along with associated electrical accessories. Required supports including structural supports /RCC/ cement concrete foundation shall be included as part of equipment . COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5. The efficiency of the equipment shall meet ECBC/ASHRAE latest standards etc. complete in all respects as per the technical specifications.(single feeder power source will be provided for outdoor units).All the structural corrosion resistant structural supports/concrete pedestals for mounting indoor/outdoor equipment\"s shall be included.Gas charging with refrigerent R 410 A shall be included at sufficient quantity recommended by the manufacturer. (Complete in all respects as per technical specification). 220 HP Air cooled |
| 640 | AIR SEPERATOR: supply, installation, testing and commissioning of Centrifugal air seperator with insulation and necessary supports and accessories |
| 641 | Supply, installation testing and commissioningofCeiling Suspended AHUs Inverter Type DuctedUnits of specifiedcapacities,nominalcapacitycondensing unit withall standard fittings, safety devices, likeHP/LPcutout, single phase preventor,overload relays,R-410A Gas,vibration isolationpadsetc. Suitabletoworktill50Degambient,BlueFinCondenserandCorrosion Resistant Body, Wide Voltage Range 360V- 440V,Scroll Compressor-driven OutdoorunitstandforDuctedmachine,vibrationisolationpadsetc. completeincludingallcharges, Anticorrosiveblackpaint(2coatepoxy painting and 2 coat primer )etc.(Complete in all respects as per technical specification) |
| 642 | 1.0TR,400CFM,30MMESP |
| 643 | 1.5TR,600CFM,30MMESP |
| 644 | 2.0TR,800CFM,30MMESP |
| 645 | 2.5TR,1000CFM,30MMESP |
| 646 | 3.2TR,1280CFM,30MMESP,Pre & Fine Filter |
| 647 | 4.5TR,1800CFM,30MMESP,pre& Fine Fliter |
| 648 | 6.5TR,2480CFM,30MMESP,pre& Fine Fliter |
| 649 | 8TR,3200CFM,30MM ESP |
| 650 | 11TR,4400CFM,30MM ESP,Pre& fine filter |
| 651 | Supply installation testing and commissioning of VRF compatible 4 way Cassette unit type with cordless remote, of following minimum capacities suitable for operationsingle phase, 230 V, 50Hz supply, including fixing of room unit, with high lift drain pump, all associated electrical works includingaccessories including power socket/power/control cabling etc, ,the filter shall be plasma and synthetic washable media type arranged for convenient cleaning and replacement. PVC condensate drain pipe (upto 5m) 6kg/sq.cm of suitable dia connecting to the drain pan ofthe indoor units to nearest drain point with necessary U-traps, elbows, fittings etc. duly insulated with 9 mm thick closed cell elastomeric class 0 insulation finished with 7 milsfactory laminated glass cloth & with required accessories like structural supports, Vibration isolator etc. complete in all respects as per technical specifications. Color/Finish(Powder Coating) shall be selected or approved by Architects(Complete in all respects as per technical specification) |
| 652 | 4TR 4 Way Cassette with drain pump |
| 653 | 3.2TR 4 Way Cassette with drain pump |
| 654 | 3.5TR 4 Way Cassette with drain pump |
| 655 | Supply of VRF / Packageair cooled Air-conditionerseach complete with Rotary compressor, air cooled condensor, GSS casing, filters, cooling coils, fan motors, copper refrigerant piping (insulated) length as per drawing maximum upto 3 mts, control wiring, refrigerant controls and accessories, including MICRO-PROCESSOR CONTROL with indication lampsfor the operation of the system withinbuilt thermostat remote controller operated with Micro- processor control panel for each machine. Tenderes to elaborate the features of Micro- processor panel. GI painted frame works for outdoor units & making good of civil work\"s |
| 656 | 2TR High wall unit |
| 657 | Supply ,Installation and testing and commissioningof double skin thermal break Treated fresh Air Handling Units complete with chilled water cooling coil, centrifugal fan, cleanable fabric pre&fine filters, flushing by pass arrangement, condensate drain pan, coil piping connections, condensate drain connections, blue fins/gold fins/blygold fins to be considered for coil, mixing box with dampers, flexible duct connectors, including thermostats that are BMS compatible, temperature controller, and sensors along with the control box, its transformer, relays, necessary power and control wiring between the thermostat, controller, AHU, PICVas shown in the drawings and specifications. The duties of equipments listed below and accessories shall be as per equipment schedule. All units shall be suitable for 415 +/-10% volts and required lengths of wiring as per site requirement to be included. VFD to be provided to suitable for the machine capacity.The electrical power wiring from the starter panel to the units shall be included. Units shall be installed as shown in the drawings and Sound Attenuators as applicable to meet the design noise criteria as specified for the capacities as under. |
| 658 | 1750CFM,40MMESP |
| 659 | 1200CFM,40MMESP |
| 660 | 850CFM,40MMESP |
| 661 | 750CFM,40MMESP |
| 662 | 450CFM,40MMESP |
| 663 | 600CFM,40MMESP |
| 664 | 100CFM,40MMESP |
| 665 | Supply, Installation ,testing and commissioning of Gas/ Liquid Copper Piping with 19mm thick nitrile rubber class \"O\" insulation of suitable thick round closed cell elastomeric insulation with minimum R value of 0.7 for pipe size greater than 40mm and 0.4 for less than 40 mm, finished with 7mils factory laminated fibre glass cloth and insulation shall have antimicrobial properties. Refrigerant piping shall have suction filters for gas line, filter drier & sight glass for liquid line as per specification for each indoor machines & outdoor units including chasing, drilling, concealing and making good the same on walls etc of following specifications as per site conditions. Suitable Refnet/ Y joints required for interconnection of piping & required pipe fittings and accessories like Bends, Tees, reducers, supports, clamps, etc shall be considered as part ofrefrigerant piping .Complete in all respects as per technical specifications. NOTE: The contractor shall ensure that all refrigerant pipe sizes required as per the design of the equipment shall be considered in the line items underneath, even if the refrigerant pipe size is not mentioned in following line items. Both refrigerant suction and liquid line shall be insulated. Complete in all respectsas pertechnical specifications.(Piping quantities are tentative and total cost quoted shall be suitable for site layout, unit location and installation requirement.) |
| 666 | 6.4mm |
| 667 | 9.5mm |
| 668 | 12.7mm |
| 669 | 15.9 mm |
| 670 | 19.1 mm |
| 671 | 22.2 mm |
| 672 | 28.6 mm |
| 673 | 34.9 mm |
| 674 | 41.5 mm |
| 675 | DRAIN PIPING: Supplying, fixing, testing and commissioning of UPVC Class E condensate drain pipe with U trap, insulation & fittings up to drain line with necessary support and accessories |
| 676 | 50mm Dia |
| 677 | 32mm Dia. |
| 678 | 25mm Dia |
| 679 | 20mm Dia |
| 680 | Supply & Installation of Inline Centrifugal Extract Fans shall be with direct driven centrifugal fan, circular section, suitable for ceiling suspension/mounting. The units shall be complete with flexible duct connections at inlet and outlet. The motor shall be protected by thermal contact relay as protection against burn-out. aswith all necessary accessories and supports |
| 681 | Ground Floor |
| 682 | 500 CFM,15MM ESP |
| 683 | 650 CFM,10MM ESP |
| 684 | 100 CFM,10MM ESP |
| 685 | First Floor |
| 686 | 225 CFM,10MM ESP |
| 687 | 100 CFM,10MM ESP |
| 688 | 325 CFM,10MM ESP |
| 689 | 500 CFM,15MM ESP |
| 690 | 650 CFM,15MM ESP |
| 691 | 1000 CFM,15MM ESP |
| 692 | Second Floor |
| 693 | 100 CFM,18MM ESP |
| 694 | 225 CFM,10MM ESP |
| 695 | 500 CFM,15MM ESP |
| 696 | 750 CFM,15MM ESP |
| 697 | 1200 CFM,15MM ESP |
| 698 | Supply, installation , testing and commissioning of metal body wall mounted proppeller fan with necessary accessories and supports |
| 699 | Supply, installation , testing and commissioning of aluminium duct with corner pieces, nut& bolt, gasket, Joints to be sealed with sealents, with all necessary hi-tech support and accessories as per the site approved shop drawing and Site condition.(for OT1,OT2 , & OT TFA Ducting ) |
| 700 | 22 G |
| 701 | 20 G |
| 702 | Supply, installation , testing and commissioning pre insulted duct withall necessary hi-tech support and accessories as per the site approved shop drawing and Site condition. |
| 703 | Supply, installation , testing and commissioning of GI volume control damper with corner pieces, nut& bolt, gasket, Joints to be sealed with sealents, with all necessary hi-tech support and accessories as per the approved shop drawing and Site condition. |
| 704 | Supply, installation , testing and commissioning of supply air aluminium powder coated diffuser with collar damper, withall necessary hi-tech support and accessories as per the approved shop drawing and Site condition. |
| 705 | Supply, installation , testing and commissioning of return air aluminium powder coated diffuser with outcollar damper, withall necessary hi-tech support and accessories as per the approved shop drawing and Site condition. |
| 706 | Supply, installation , testing and commissioning of supply air aluminium powder coated grille with collar damper, withall necessary hi-tech support and accessories as per the approved shop drawing and Site condition. |
| 707 | Supply, installation , testing and commissioning of return air aluminium powder coated grille without collar damper, withall necessary hi-tech support and accessories as per the site approved shop drawing and Site condition. |
| 708 | Supply, installation , testing and commissioning ofaluminium powder coated louver withall necessary hi-tech support and accessories as per the site approved shop drawing and Site condition. |
| 709 | Supply, installation , testing and commissioning of class \"o\" closed cell nitrile rubber insulation with self adhesive. Duct surfce to be cleaned before applying adhesive and joints to sealed with 3mm thick,5centimeter black tape. |
| 710 | 13mm Thick |
| 711 | 19mm Thick |
| 712 | Supply, installation , testing and commissioning of class \"o\"open cell Acoustic insulation with self adhesive. Duct surfce to be cleaned before applying adhesive . |
| 713 | 10mm Thick |
| 714 | Supply, installation , testing and commissioning of class \"o\"closed cell nitrile rubber insulation for under deckwith self adhesive. |
| 715 | 13mm Thick |
| 716 | Supply, installation, testing and commissioning of manually operated, opposed blade, duct mounted, flanged volume control dampers of required sizes inGI construction with operating mechanism, mounting arrangement, rubberrefrigerant kits etc. complete. |
| 717 | Supply, installation , testing and commissioning of HEPA filter,Plenum Construction : 1 mm Aluminium construction having Aluminium Square tube skeleton structure,Perforated diffuser: 1 mm Stainless Steel (SS-304) Inline Round Perfoaration : 5mm ø,12 mm Pitch,Filter fitment : Filter face seating on a self-leveling Poly Urethene compound formed on the Plenum structure,Thermal insulation : 19 mm thick Class \"O\" Nitrile insulation with aluminium foil lamination on exterior side,Duct connecting collar : No. of Duct connecting Collars -Based on user requirements Maximum Height : 225 mm,Volume control dampers : Aluminium Aerofoil Volume Control Damper Operable from the OT side without distrubing filter installation,Suspension brackets : SS \"L\" angle brackets for ceiling suspension of the Plenum, with all necessary hi-tech support and accessories as per the site approved shop drawing and Site condition.Plenum Size: 2350 (L) x 1740 (W) x 455 (H) mm (Excluding Thermal Insulation) |
| 718 | Supply,install,testing and commissioning of strip heaters comprising thermostat,humidistat, safety thermostat, contactors, Controls & control Wiring. Minimum capacity of strip heaters shall be 2 KWx3Nos |
| 719 | Supply of the following sizes of Ladder Type FRP cable trays with vertical sides on both ends as per approved design and FRP supports with coupler plates spaced 300mm apart throughout the length as specified, including the cost of support hooks, fasteners, painting if required etc.( Contractor shall ensure to use corrossion free materials as support or fastening fittings). 300mm(300x100x25) |
| 720 | Supplying, Fixing, Testing & commissioning at site in position2 HP Axial Fan for ExhaustSpecification :Fan Casing is made of heavy gauge MS Sheet (as per IS-1079/2062) having robust construction. It has flanges at both ends for easy fixing on ducts/walls. Impeller is made of Die Cast aluminium having aerofoil design with adjustable pitch angles. fitted with 2 Hp , 4 Pole, 440 volts , 50 Hz, 3 Phase Motor |
| 721 | Supplying, Fixing, Testing & commissioning at site in position1 HP Axial Fan for Fresh Air Specification :Fan Casing is made of heavy gauge MS Sheet (as per IS-1079/2062) having robust construction. It has flanges at both ends for easy fixing on ducts/walls. Impeller is made of Die Cast aluminium having aerofoil design with adjustable pitch angles. fitted with1 Hp , 4 Pole, 440 volts , 50 Hz, 3 Phase Motor |
| 722 | Supplying, Fixing, Testing & commissioning at site in positionGI Ducting with Fittings For Exhaust Specification : 22 Swg Gi Sheet Of Tata/Jindal With All Connected Accessories For Fitment Of The Duct On The Ceiling And With Hood As Per Site Layout/Site Conditions. Plat Form For Fixing Blower, Smooth Bends, Bents To Be Fixed With GI Angle And GI Suspenders Fixed On To The Ceiling/Wall With All Allied Fixing Materials. The Jointing Flanges To Be Made With 35x35x3 Mm. GI Angle. 8mm GI Rods And Painted 5mmx35mmx3mm GI Angle At An Interval Of 2mtr Shall Be Used To Suspended The Ducting On To Ceiling/Wall. Duct Joints to Be Bolted Together With Gasket for Air Tight Seal. |
| 723 | Supplying, Fixing, Testing & commissioning at site in positionGI Ducting with Fittings For Fresh Air Specification : 22 Swg Gi Sheet Of Tata/Jindal With All Connected Accessories For Fitment Of The Duct On The Ceiling And With Hood As Per Site Layout/Site Conditions. Plat Form For Fixing Blower, Smooth Bends, Bents To Be Fixed With GI Angle And GI Suspenders Fixed On To The Ceiling/Wall With All Allied Fixing Materials. The Jointing Flanges To Be Made With 35x35x3 Mm. GI Angle. 8mm GI Rods And Painted 5mmx35mmx3mm GI Angle At An Interval Of 2mtr Shall Be Used To Suspended The Ducting On To Ceiling/Wall. Duct Joints to Be Bolted Together With Gasket for Air Tight Seal. |
| 724 | Supplying, Fixing, Testing & commissioning at site in positionFresh Air Grill |
| 725 | Supplying, Fixing, Testing & commissioning at site in positionWall Mount Exhaust Hood With Baffle Filters size-1800*900*500 mm ,Exhaust Hood with filters for Bulk range & Hot plate Wall mounted type :20 SWG SS 304 body; SS 304 Baffle filters , air grill and oil collection tray |
| 726 | Supplying, Fixing, Testing & commissioning at site in positionWall Mount Exhaust Hood With Baffle Filters -size-1250*750*500 mm,Exhaust Hood with filters for Bulk range & Hot plate Wall mounted type :20 SWG SS 304 body; SS 304 Baffle filters , air grill and oil collection tray |
| 727 | OXYGEN SYSTEM (O2): Supply, Testing and commissioning of Fully automatic Oxygen Control panel Model AMAZON -D with flow rate of 2100 LPM Fully complying with ISO 10524-2, ISO 7396-1:2007/HTM02-01 as per technical specification. (Make: Drager ) |
| 728 | Oxygen Manifold : Supply, testing and commissioning of Oxygen Manifold - 2 banks x10 cylinders including Copper tail pipes. (Make:Drager) |
| 729 | Oxygen Emergency Manifold: Supply, testing and commissioning of Emergency Oxygen manifold 1 x 5 with IOX-14 high flow regulator (Make: Drager) |
| 730 | NITROUS OXIDE (N2O) SYSTEM: Supply, Testing and commissioning of Semi -automatic Nitrous Oxide Control panel with minimum flow rate of 2000LPM Fully complying with ISO 10524-2, ISO 7396-1:2007/HTM02-01 as per technical specification. (Make: Drager) |
| 731 | Manifold System N2O: Supply, testing and commissioning of Nitrous Oxide Manifold - 2 banks x 2 cylinders including Copper tail pipes. (Make: Drager) |
| 732 | Emergency Manifold N2O: Supply, testing and commissioning of Emergency Nitrous Oxide manifold 1 x 2 with IOX-14 high flow regulator. (Make: Drager) |
| 733 | CARBON DI-OXIDE SYSTEM: Supply, Testing and Commissioning of Carbon Dioxide manifold - 1 x 2 with IOX-14 High Flow Regulator. (Make: Drager) |
| 734 | MEDICAL AIR SYSTEM: Supply Installation, Testing and Commissioning of ANESTIWATA (Japan) Make Model BFT 75C- 9E 7.5 Hp Non - Lubricated Air Compressor Base frame mounted -24.43 cfm (692 Lpm) - 2 Nos. with all standard accessories. |
| 735 | Air Dryer system: Supply, Installation, Testing and Commissioning of TRIDANT Make Desiccant Air Dryer. Model : DRYSPELL PLUS 45 - 60 CFM |
| 736 | VACUUM SYSTEM: Supply, Installation, Testing and Commissioning of. ANEST IWATA Make Vacuum Pump Model:BVLS 50 DE - 5HP - 2 Nos with 1000 Ltr Vacuum Receiver tank - 1 No, Vacuum switch - 2 No., DOL starter - 2 No, 5 HP Motor - 2 No. with inter connecting pipes |
| 737 | COPPER PIPING Supply, installation testing and commissioning of Copper pipe: Per Mtr. It must comply with EN 13348as per technical specifications.Make: Mexflow |
| 738 | 15 mm |
| 739 | 22 mm |
| 740 | 28 mm |
| 741 | 35 mm |
| 742 | 42 mm |
| 743 | 54 mm |
| 744 | MEDICAL GAS OUTLETS Supply, Installation, testing and commissioning of DIN Gas Outlets meeting requirements of EN ISO 9170-1Make: Drager |
| 745 | O2 Outlet with probe |
| 746 | N2O Outlet with probe |
| 747 | Air 4 Outlet with probe |
| 748 | Air 7 Outlet with probe |
| 749 | CO2 Outlet with probe |
| 750 | Vacuum Outlet with probe |
| 751 | Anaesthesia Gas Scavenging System Outlet (AGSS) Ventury type with probe (Make: Drager) |
| 752 | Supply, Installation, testing and commissioning of Area Valve Service fully complying with ISO 7396-1:2007 (Make: Aktive Technologies) |
| 753 | 2 Gas With Valves (15/22) |
| 754 | 3 Gas With Valves (15/15/22) |
| 755 | 4 Gas With Valves (15/15/15/22) |
| 756 | 6 Gas With Valves (15/15/15/15/15/22) |
| 757 | AREA ALAM PANELS Supply, Installation, testing and commissioning of Digital Area Alarm Service fully complying with ISO 7396-1:2007 (Make Aktive Technologies) |
| 758 | Medical Gas Area Alarm Digital 2 Gas |
| 759 | Medical Gas Areal alarm Digital 3 Gas |
| 760 | Medical Gas Area Alarm Digital 6 Gas |
| 761 | BALL VALVES Supply, installation, testing and commissioning of Ball Valves, complying with HTM 02-01, as per technical Specifications. Make: UN Med |
| 762 | 15 mm |
| 763 | 22mm |
| 764 | 28mm |
| 765 | 35 mm |
| 766 | 54 mm |
| 767 | SERVICE DELIVERY UNITS: Rigid Pendant Rigid Pendant Vertical type with Provision for Medical Gas Outlets and Electrical Sockets with 1 Monitor stand |
| 768 | Bead Head Panels (BHU)Supply, Installation, testing and commissioning of Bed head panels with Medical gas Terminal unit provisions as per tender drawing, Provision for Electrical and data points as per consultant specification.(Make: Drager / Stark Storme)4 Feet Long |
| 769 | ACCESSORIES (Make: GHL) |
| 770 | Oxygen BPC Flowmeter with Humidifier Bottle |
| 771 | 600 Ml Wall Suction Unit |
| 772 | Theatre Suction Unit with 2 x 2000 ml Bottles |
| 773 | Medical Oxygen Generation Plant 1. Compressed Air Station Modular rotary screw compressor with refrigeration dryer & air receiver, equipped with the followings:from FS CURTISa) Air compressor b) Refrigeration air dryer c) Air filtration system d) Air tank :1500L2. OXYGEN PSA GENERATORa) 2 PSA sieve beds b) 1 monitoring system CPU Controller with digital screen c) 1 separate oxygen receiver equipped for oxygen service d) 2 air inlet filters (25 μm and 0.1 μm)e) 1 oxygen outlet filter * Flow : 10.5 m3/h at purity 93% + 3%* Pressure : 4.5 to 6 bar-g* LPM : 1753. OXYGEN BUFFERa) Vertical configurationb) Capacity : 1000 L |
| 774 | OT TABLE • Table type: fully electric• Height adjustable range: 750mm to 1000mm• Trendelenberg : 30 degree• Maximum patient load: 200 kgs• Table length: 1930mm• Table width: 533mm• Trendelenberg reverse: 25 degree• Lateral tilt: left :20 degree/right :20 degree• Back rest: up:80 degree/down:25 degree• Leg rest:up:15 degree/down:90 degree• Head rest :up:20 degree/ down:60 degree STAAN/CONFIDENT/AMSCO |
| 775 | OT LIGHT • Double doom• Light source type:L.E.D.• Color temperature: 4300 K• Intensity: 1,60,000 Lux• Focus diameter: 15-20 cm• Led lifetime: 50,000 hours.• Light head diameter: 53cm• Control unit: SMPS• Color rendering index: 93• No of LEDs: 63 DR MAACH/STAAN/STRYKER |
| 776 | ANESTHESIA PENDENTAnesthesia Pendent with Single Arm, Terminal units as per consultantdrawing,330 degree angle rotation of column and arm, with air break as standardfor arm system, 2shelves ,IV pole with arm- 1no.,Provision for 12 nos Electrical and 4 data points. |
| 777 | SURGERY PENDENT Surgeon Pendent with Double Arm , Terminal units as per consultantdrawing,330 degree angle rotation of column and arm, with air break as standard for arm system, 3shelves.Provisionfor 12 nos Electrical and 4 data points.• Microprocessor controlled• Smart feedback system• Pre-defined programs• Monopolar & bipolar modes• Soft, Swift, Force & Spray coagulation• Dual output for monopolar coagulation• Split patient plate indicator• Bipolar coagulation with auto start• Automatic power regulation•quality monitoring systemALAN/VALLEYLAB/COVIDIEN |
| 778 | FULLY AUTOMATIC HORIZONTAL STEAM STERLISER TUTTUNEUR/GETTINGE/MMM |
| 779 | HORIZONTAL STEAM STERILISER• Design pressure: 0.26MPa•Design temperature: 150℃•Maximum working pressure: 0.23MPa•The accuracy of temperature display: 0.1℃•Selection of sterilization temperature: 105℃~138℃•Uniformity of temperature: ≤ ± 0.5℃•Material of the cavity: SUS304 stainless steel•Requirements for water sources: Distilled water or RO water. YORCO/OSE |
| 780 | ETO STERILISER• Computer controlled profit. Simple and convenient operation. display of operating status(including temperature). Temperature. Negative pressure. Sterilization time. Residual gastreatment time/times).•Record and print the sterilization information of the whole process. For verification and filing.•Built-in humidity sensor; Select advanced imported humidity sensor, automatic detection of sterilization indoor humidity. With automatic program recovery function: regardless of power failure. Power outage. Or computer program element disorder, can judge its fault point. The program automatically restores after powering on.•Multiple protection functions: no over-voltage and over-temperature protection function. More secure and reliable.•The air inlet is equipped with aseptic filter, which can effectively remove bacteria and microorganisms, and avoid secondary pollution when discharging residues. |
| 781 | PLASMA STERILISER JOHNSON& JOHNSON |
| 782 | ULTRASONIC CLEANER Freestanding ultrasonic washer for surgical instruments to process up to 16 lumened devices, or up to 35 lbs. per cycle* Automated dosing and delivery of chemistry Simple operation with touch screen control that clearly displays cycle statusUNIDENT/VEVOR |
| 783 | INSTRUMENT DISINFECTOR50% more throughput compared to standard single chamber washersUses as low as 31 gal. water/cycle; Process up to 300 DIN trays/8-hour day |
| 784 | DRYER UNIT |
| 785 | SEALING MACHINE• Stainless steel material• Sterilization pouch packing• Capacity of 10M/Min SEAPACK |
| 786 | SITC OF Pre‐Fab Wall Panel:Stainless Steel Grade 304 Panel : The Pre‐fabricated modular constructionisdesignedandconstructedforexactsize,easy field installation and future disassembly, enlargement, or relocation. The operating roomwill be constructed from Pre‐fabricated Panel of 1.2 mm or more thick Stainless Steel Grade304sheets,witha12mmthickbackingofgypsum board |
| 787 | SITC OF Substructure Steel Assembly : Substructure elements of 1.5 mm thick GI extending from the finish floor to ceilingslabtomakethewallpanelsfreestanding.Suitable substructure in GI for mounting wall panels along walls, with cross members to support equipment\"s flush mounted in to the wall panels. Substructure will also have provision for routing electrical wiring and gasPipeline. |
| 788 | SITC OF Pre‐Fab Ceiling:Stainless Steel Grade 304 Panel : The Pre‐fabricated modular constructionisdesignedandconstructedforexactsize,easy field installation and future disassembly, enlargement, or relocation.Theoperatingroomceilingwillbeconstructed from Pre‐fabricatedPanelof 1.2 mm or more thick Stainless SteelGrade304sheets,witha12mmthickbackingof gypsumboard.Suitablegridstructuresuspendedfromthe ceiling slab should be provided to support the ceiling panels to therequiredheight,andalsoprovideforeasyroutingof electricalconduits,gaspipelinesand bioair‐conditioning ducts. |
| 789 | SITC OF Antimicrobial Coating:Filling of all Joints and cavities with metallic Epoxy Filler and SandedFlushtoprovideajointlessfinishandthensprayed withawaterbasedliquidplasticasepticandselfsterilizing wall coating system to a d.f.t. of 300microns with primer. |
| 790 | SITC OF Antistatic Conductive/ Dissipative Flooring: Seamlesswithperfectlycurvedflush‐covings,resistanceto mechanical stresses and dynamic loads and having conductive protection characteristics, 2 mm thick, washable |
| 791 | SITCOFHermeticallySealingtypeofManualSliding/ SwingDoorhavingthicknessof40‐48mmofsize1500X 2100 mmsingle / dual leaf with PUF core sandwiched betweenAntimicrobialHighPressurelaminates(HPL),with viewing window of size 300 X 300 mm. The door leafs hung on extruded heavy duty aluminium alloy extrusion Doorframe for single side swing Doors, Sliding Door leafs runs on (nylon wheels) within an extruded heavy duty aluminium alloy extrusion track / frames, for smooth effortless sliding with the help of handle. |
| 792 | SITCOFMicroprocessorbasedElectronicAutomation (Operator ) for Manual Door for controlling the direction of movements, the acceleration and speed of the door, with a low noise levelpulse generatormotor. Itincludes a photocell for users safety. (For sliding door) |
| 793 | CONTROL PANEL:SUPPLY, INSTALLATION, TESTING AND COMMISSIONING OT CONTROL PANEL, MOUNTED FLUSH IN THE THEATRE WALL ALONG WITH DIGITAL DISPLAYS COMPRISING OF THE FOLLOWING:1.DAY TIME CLOCK (DIGITAL)2.TIME ELAPSED CLOCK (DIGITAL) 3 TEMP. AND 4. HUMIDITY DISPLY. 5. POSITIVE PRESSURE STATUS. |
| 794 | SITC of ULTRAVIOLET LIGHT: UV LAMP FIXTURE MADE OF SS304 AND FITTED WITH 30 W UV TUBES. |
| 795 | DENTAL CHAIR WITH EQUIPMENTTRISCO/CONFIDENT/SKANRAY |
| 796 | LABOUR TABLE• Heavy duty tabular frame work on smooth running castors with brakes• Five section top with mattress• Back section adjustable on pneumatic pump• Trendelenburg and reverse trendelenburg by crank mechanism• Table can be positioned as chair and lithotomy pelvic position upto 120 mm• Size: 1830 L x 600 W x 810 H mm approx• Pre-treated and Epoxy Powder Coated |
| 797 | GAS WORK: Supplying, Fixing, Testing & commissioning at site in positionGas BankSpecification : (3+3) Manifold SS 304 1/2 pipe Schedule 40 S with Necessary Fittings 3/8 needle valve unitechEmergency shutter valve 1/2\"4\" ss measure guageManifold valve ss valveNon return valve (gasman)Liquid drain filterQC adapter (gaso)Cylinder pigtail 2ft.Booster valve united 30 PSIRange connector (Lumpsum) |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
