|
| 1 | Excavation for foundation in earth, soils of all types, sand,gravel and soft murum, including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5m to 3.0m) Spec.No. :-Bd.A.1/Page No.259 |
| 2 | Excavation for foundation in earth, soils of all types, sand,gravel and soft murum, including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5m to 3.0m) Spec.No. : Bd.A.1/Page No.259 |
| 3 | Providing and filling in the foundation with sand of approved quality including watering, compacting etc. complete. (To be executed with prior approval of Superintending Engineer)Spec.No. :- Bd.A.13 Page No. 264 |
| 4 | Providing soling using 80 mm size trap metal in 15 cm. layer including filling voids with Crushed sand/grit, ramming, watering etc. complete.Spec.No. :- As directed by Engineer in charge. |
| 5 | Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete.With natural sand/V.S.I. quality Artificial Sand Spec. No. : Bd.E. 1/Page No. 287/I.S. 456 (2000) |
| 6 | Providing andlayingCastinsitu/ReadyMixcementconcreteM-25oftrap/granite/quartzite/gneissmetalforR.C.C.workinfoundationslike raft,strip foundations,grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water,Steel centering,formwork,coverblocks,laying/pumping,compactionandcuring roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)Spec.No. :- Bd.F.3 Page No. 298 and B.7, Page No.38 |
| 7 | ProvidingandlayingCastinsitu/ReadyMixcementconcreteM-25oftrap/granite /quartzite/gneissmetalforR.C.C.columnsasperdetaileddesignsanddrawingsoras directedincludingsteelcentering,formwork,coverblocks,laying/pumping,compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smoothand even surface or roughening if special finish is to be providedand curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 8 | Fillinginplinthandfloorswithcontractors material/broughtfromoutside andapprovedbyEngineer incharge inlayersof15cm to20cm includingwateringandcompactionetc. complete.(SSR-2021-22/Item No.-21.37/Page No.-) |
| 9 | Providing andlayingCastinsitu/ReadyMixcementconcreteinM-25oftrap/granite/ quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping,compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcementandstructuralsteel).withfullyautomaticmicroprocessorbasedPLCwith SCADAenabledreversibleDrumTypemixer/concreteBatchmixplant(Panmixer)etc. complete. With fine aggregate (Crushed sand VSI Grade) |
| 10 | Providing fly ash brick masonry with conventional / I.S. type fly ash bricksin C.M. 1:6 in foundation and plinth includingbailing out water manually striking joints, racking out joints watering and scaffolding etc. complete. As director by engineer in charge and BDG- 2 and 5 |
| 11 | Providing and laying Cast in situ/Ready Mix cement concrete M-15 of trap/ granite/quartzite/gneiss metal for coping to plinth or parapet, moulded or chamfered as per drawing or as directed including steel centering, plywood/ steel formwork compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) |
| 12 | Providing fly ash brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. CompleteAs director by engineer incharge and BDG- 2 and 5 |
| 13 | Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of 2 bars of 6 mm diameter / 2 hoop iron strips 25 mm X 1.6 mm placedat every third course, properly bent and bonded at ends scaffolding, racking out joints and watering etc. complete. |
| 14 | Providing and laying Cast in situ/Ready Mixcement concrete M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting androughening the surface ifspecial finish is to be provided and curing complete. (Excluding reinforcement and structural steel). withfullyautomaticmicroprocessorbasedPLCwithSCADA enabledreversibleDrum Typemixer/concreteBatchmixplant(Panmixer)etc.complete.Withfineaggregate (Crushed sand VSI Grade) |
| 15 | Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landingsas per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) |
| 16 | Providing and fixing in position TMT- FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations,slabs, beams columns, canopies, staircase, newels, chajjas,lintels pardis, copings, fins, arches etc. as per detailed designs,drawings and schedules. including cutting, bending, hookingthe bars, binding with wires or tack welding and supporting asrequired complete. |
| 17 | Providing internal cement plaster 20mm thick in a single coat in cement mortar 1:5 to concrete, brick surfaces in all positions including scaffolding and curing. Providing groove at joint of B.B.Masonry and concrete members complete. |
| 18 | Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. |
| 19 | Providing and applying Texture plaster with finishing with texture material of approved make in 3 to 4 millimeter thickness on previously plastered surface, including Plaster Groove 6mm thickness or Tape Grooves 35 to 45 mm thickness or as required, in all position including preparing the surface, scaffolding etc. complete. |
| 20 | Providing and laying machine cut machine Polished Kota stone flooring 25mm to30mm thick and required width in plain/diamond pattern on bed of 1:6C.M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete |
| 21 | Providing and laying vitrified mirror / glossy finish tiles decorative typehaving size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearingetc. complete. a) Flooring |
| 22 | Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearingetc. complete.b) Skirting |
| 23 | Providing and laying Antiskid Ceramic tiles of approved qualityof size 30 cm x 30 cm and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete. |
| 24 | Providing and laying ceramic tiles having size 30 cm. x 60 cm. confirming to corresponding I.S.for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete. |
| 25 | Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade withfullmoulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaningetc. complete. |
| 26 | Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete |
| 27 | Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing,etc. complete. |
| 28 | Providing and fixing Country cut teak wood double or single leaf second class fully panelled door shutter with 35mm thick style and rail with 25 mm thick panels with openable fan light as per detailed drawings. Excluding the door frame 60mm x 100mm stainless steel fixtures and fastening and finishing the wood work with oil painting 3 coats. (Excluding the door frame) |
| 29 | Providing and fixing solid core flush door shutter in single leaf 32 mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3 mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete. |
| 30 | Providing and fixing Country cut teak wood windows with double leaf 25 mm thick planked shutterswithoutventilatorsasperdetaileddrawingsincludingstainlesssteelfixturesand fastenings and finishing the wood work with oil painting 3 coats etc. complete |
| 31 | Providing and fixing in position Mild steel fixed staggered ( Z Type ) Ventilatoras per detailed drawing with hot deep zink coating including fabricating with Mild steel\"Z \"Section of size 20mm x 25 mm and 3 mm thick at weight 1.42 Kilogram/One RunningMetre,with stainless steel mosquito net of 304 Grade,4 mm thick float glass ?as directedby Engineer In charge including necessary welding, grinding, two coats of oil paintetc.complete |
| 32 | Providing and fixing mild steel grill work for windows, ventilators, etc. 20 Kg / Sqm. as per drawing including fixtures necessary welding and painting with one coat of anticorrosive paint and two coats of oil painting complete. |
| 33 | Providing and fixing collapsible steel gate in one / two leaves with hot rolled verticalchannels of 18 x 9 x 3 mm minimum size, crossings of M.S. flats of size 18 x 5 mm T orE section for runner of minimum 40 x 6 mm size for flange, M.S. flat for top runner ofminimum size 40 x 12 mm with roller wheels confirming to grade F.G. 150 fittedwith snap headed rivets of minimum size 6 mm max. spacing of vertical channels be100 mm enclosed gate position and clear space of 150 mm between two sets ofcrossings with hold fasts, stoppers, spaces, handles, locking arrangement and one coatof red lead primer and oil painting etc. complete. (I.S. 105211983). |
| 34 | Providing and fixing 50mm diameter and 1.5 mm thick vertical and top Stainless steelhand railing in S.S.304 Grade with Stainless steel square / circular pipe bracing of size 32mm x32mm x1.5 mm in 3 rows including fabricating ,fixtures, errecting, necessarywelding, grinding, finishing, buffing to stainless steel pipe etc. complete |
| 35 | Providing and applying two coats ofexterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary , and watering the surface for two days etc complete. |
| 36 | Providing and applyingimpression 24 carrat Luxury paint of approvedmake & approved brand Emulsion paint to interior walls and ceilings of approved quality, colour and shade to new surface in two coats, including sub surface prparation by Acrylic putty and Acrylic primer coats including scaffolding, preparing the surface. etc. complete (Low VOC). |
| 37 | Providing and fixing 8 cm C.I. Nahani Trap including C.I. grating bend and piece of C.I.pipe upto the outside face of the wall complete |
| 38 | Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete1:4:8 outside the building including cast iron grating in the sink, connecting glazedstoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for thegully trap |
| 39 | Providing and constructing Brick Masonry Inspection Chamber 60cm x 45cm x90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channelshalf round G.S.W. pipes, Brick Masonry, plastering from inside and with frame fixed incement concrete with R.C.C. Cover medium duty 140Kilogramwith frame etc complete. |
| 40 | Providing and constructing Brick Masonry Inspection Chamber 90cm x 45cm x90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channelshalf round G.S.W.pipes, Brick Masonry, plastering from inside and with frame fixed incement concrete with R.C.C. Cover medium duty 140Kilogramwith frame etc complete |
| 41 | Providing, laying and fixing P.V.C. pipe of 75mm dia. with fittings such as bends,tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete.Including removing existing pipe line if necessary and conveying and stacking thesame in PWD chowky or as directed etc. complete. |
| 42 | Providing, laying and fixing P.V.C. pipe of 110 mm. dia. with fittings such as bends,tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete.Including removing existing pipe line if necessary and conveying and stacking thesame in PWD chowky or as directed etc. complete. |
| 43 | Providing and fixing white glazed earthenware Wash Hand Basin of 63cm x 45cmsize including Bib cock stop tap brass heavy 15mm, brackets, rubber plugs and brasschain, stop tap and necessary pipe connection including P.V.C. waste pipe and trap up tothe outside face of the wall |
| 44 | Providing and fixing on walls/ ceiling/ floor 15 mm dia. CPVC pipe with necessaryfittings, remaking good the demolished portion etc. complete. Including removing existingpipe line if necessary and conveying and stacking the same in PWD chowky or as directedetc. complete |
| 45 | Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessaryfittings, remaking good the demolished portion etc. complete. Including removing existingpipe line if necessary and conveying and stacking the same in PWD chowky or as directedetc. complete |
| 46 | Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessaryfittings, remaking good the demolished portion etc. complete. Including removing existingpipe line if necessary and conveying and stacking the same in PWD chowky or as directedetc. complete. |
| 47 | Providing and fixing 20 mm dia. screw down bib/ stop tap of brass including necessarysocket union nut complete. |
| 48 | Providing, laying and fixing P.V.C. pipe of 15mm dia. with fittings such as bends,tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete.Including removing existing pipe line if necessary and conveying and stacking thesame in PWD chowky or as directed etc. complete. |
| 49 | Providing, laying and fixing P.V.C. pipe of 20mm dia. with fittings such as bends,tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete.Including removing existing pipe line if necessary and conveying and stacking thesame in PWD chowky or as directed etc. complete. |
| 50 | Providing, laying and fixing P.V.C. pipe of 25mm dia. with fittings such as bends,tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete.Including removing existing pipe line if necessary and conveying and stacking thesame in PWD chowky or as directed etc. complete. |
| 51 | Providing and fixing H.D.P container one piece moulded water tank made out of highdensity polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet,outlet overflow pipe inclusive of all tankscapacity between 200 to 1000 liters |
| 52 | Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mmdia. nickel plated towel rod etc. complete. |
| 53 | Providing and fixing Orissa type white glazed earthenware 575 mm water closetpan including S trap with earthenware foot rests, cast iron soil and vent pipe upto outsideface of the wall 1:2:4 brick bat lime concrete bedding without flushing tank and itsaccessories etc. complete. |
| 54 | Providing and fixing European type white glazed earthenware coupled closet symphonictrap with symphonic low level white glazed 10 litres cistern with black backliteseat with all necessary pipe connection etc. complete |
| 55 | Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) treatmentby treating the backfill in immediate contact with foundation at the rate of 5 litres ofemulsion concentrate of 1.0 percent of clorophyrifos per One Square Metre of verticalsurface area covering 10 years guarantee on bond paper. |
| 56 | Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating thetop surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0percent of clorophyrifos per One Square Metre of surface area covering ten yearsguarantee on bond paper |
| 57 | Providing and applying water proofing treatment using acrylic polymer modifiedcement based water proofing coating with fibre glass mesh mixing at the rate ofpowder to liquid (2:1) by weight covering 9 to 10 Square Metre /Kilogram withtwo coat using approved chemicals for masonry and concrete surface by brush covering7 years guarantee on Stamp Papers etc. complete |
| 58 | Providing and Fixing Vertical Blinds of approved Make and shade of 100mm regularfabric with powder coated aluminium channel with telting PVC chain & bottom weightplate with all necessary fixtures and fitting etc. complete. (Sample to be final by EngineerIn-charge prior execution of work) |
| 59 | Providing and Fixing of Mineral Fibre Suspended Ceiling System with Bioguard(Bevelled Tegular) EDGE TILES WITH 15mm Exposed GRID. The tiles shouldhave Humidity Resistance (RH) of 99%, Light Reflectance 90%, Thermal Conductivityk = 0.052 - 0.057 w/m K, Colour White, Fire Performance UK Class 0/Class 1 (BS476 Part 6 and 7), in module size of 600x600 x 16mm with Anti Microbial coatingon the face of the tile, suitable for Green Building application, with Recycled contentof 34%. The tile shall be laid on precoated G.I. channel on XL2 Clip having a webheight of 32 mm 32 with 15 mm wide T - section flanges colour white having rotarystitching on all T sections i.e. the Main Runner and 1200 mm Cross Tees with a webheight of 32 mm and a load carrying capacity of 7.7 Kilograms/M2 and pull outstrength of 100Kilograms. . The T Sections have a Galvanizing of 90 grams per M2 andneed to be installed with Suspension system The Tile and Grid system used togethershould carry a 10 year warranty. products approved at GRIHA and BS 476 etc. complete. |
| 60 | Providing and fixing in position U.P.V.C.(Unplasticized Poly Vinyl Chloride) havingmulti- chambered outer frame section (73 x 50)mm with an outer wall thickness of2mm & steel reinforcement, multi-chambered slider frame (73x 60) mm with steelreinforcement, multi- chambered slider sash (46x 82) mm with steel reinforcementdesigned to give optimum strength, 5 mm thick toughened double glass with 12 mmspacer of good quality including alluminium track, Inter-locking profile, coextrudedbeadings, EPDM gaskets,silicon sealent,sliding handle, fixtures and fastenings(couplings, hinges) including with all required screws and nuts with all necessaryU.P.V.C. sections as per the detailed drawing and as directed by Engineer-In-Chargeetc. complete. |
| 61 | Providing and fixing 4mm thick High Pressure interior compact Laminate made out ofthermosetting resign treated Kraft as core material and design paper as a finish surface.Compact laminates should have the characteristic of flame retardant fulfilled the criteria ofunder BS-476/97 and EN438-6 with classification of BS1D0 standard property, Antibacterial and anti-termite property under JIS Z2801:2000, Chemical resistance, Scratchresistant ,fire resistance, weather & climatic shock resistance( The manufacturer shouldprovide10 years warranty certification on any manufacturing and moisture relateddefects.)The compact laminates should be resistance to water immersion throughpermissible increase on thickness and mass <0.60% and board should have density>1.35kg/cm3 and fulfilled the criteria of FSCand Green Guard Gold certification andmanufactured under EN438-2&3:2005 standard . Finish and colour of compact laminatesshould be finalised under direction of Engineer –in-charge.Including fixing Compactlaminates on 25x50mm aluminium tube or approved tube size at 600mm c/c underdesirable height and fixed through same compact colour rievts or compact adhesive as perrecommended by compact supplied agency. Finish and colour of Interior clade should beapproved under engineer-in-charge direction |
| 62 | Full Height Partitions in Glass finish - Providing and Fixing 80mm to 85mm thick Fullheight Double Skin partition up to 3 mtr height with All visible sections in Anodized /Powdercoated finish. Made up of Frames and Tiles. Frame construction In combinaton ofAluminium Rails and Bottom ,Center and Top members, Connected with 2 way RoundShape Post , 3way Post , 4 way Post made up of Aluminium Extruded and Tiles in 5mmthk. Non Toughened Glass on both side. With all the Joints in the partitions covered withPVC extrusions to provide better sound Proofing. Tiles to be separated 55mm from eachother to provide adequate space for drawing cables for electric, data and telephone withproper facility for fixing electrical and data switch plates. as per design and drawing. |
| 63 | Providing and fixing in position, Double shuttered aluminium extruded powdercoated openable door of specified size with aluminium door frame of powder coatedsection 101.60 x 44.75mm , 3.18 mm thick and shutter comprising of powder coatedsection having bottom and lock rail of size 150 mm x 44.5 mm x 3.00 mm thick top rails47.62 x 44.45 mm x 3.00 mm thick , vertical style 47.62 x 44.45 mm, 3.00 mm thick andfor shutter plain glass panes 5 mm thick for top panels and 12mm thick both sidelaminated phenol bonded particle board panels for bottom panels etc. , I.S.I. mark, heavy duty, Hydraulic floor spring of 150Kilogramcapacity , having heavy dutyconcealed lock, necessary beading, glazing clips, PVC gaskets, 250mm lengthaluminium tower bolts, 150mm dia. pad handle, etc. as per detailed design anddrawing or as directed by engineer in charge including all materials , labours, andequipment etc.complet |
| 64 | CUSTOM PRINTED ACOUSTICAL FALSE CEILING :Providing & Fixing of Customcolor Printed Mineral Fibre Acoustical Suspended Ceiling System with 19mm thickMicrolook 90 Edge Tiles with 15mm face exposed grid. The tiles shall have smooth bright laminated visual with Humidity Resistance (RH) of 99%, NRC 0.7 (Average value ofAbsorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as perASTM C423 standard, CAC of 41db as per ASTM E1414, Light Reflectance ≥87% as perASTM E-1477, Thermal Conductivity k = 0.045 - 0.048 W/mK, Colour Global White,Fire Performance of Class 0/1 as per BS 476 Part6/7 and Class A as per ASTM E 84 with19mm Square Tegular/Microlook 90˚ edge and 8mm drop in module size of 600 x600mm. The scrim on the face of the tile shall be cleanable, soil and scratch resistant andhaving superior scrub-ability (Gardner Test). The tiles shall be classified as ISO 14644-1cleanroom class 5. The tile shall have a rating of 8 or above for tests conducted forResistance to growth of Mold in accordance to ASTM D3273. It shall be suitable forGreen Building application, with Recycled content of 36%. The tile shall havecertifications from GRIHA and GreenPro thereby confirming that it is an environmentfriendly product. SUSPENSION: The tile shall be laid on with 15 mm wide T - sectionflanges colour global white (matching to tile color) having roll formed double strokerotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Teeswith a web height of 38mm (all sections). The deflection loading of the system shall be12.5 kg/m2 (as per standard installation layout mentioned below) and main beam tested asper ASTM C635 (Deflection limit less than L/360) with a deflection loading of 15kg/m.The end details of the cross tee shall be made of pre hardened steel and fixed to the endsof the cross tee to provide double locking between “cross tee to cross tee” and “cross teeto main beam”. All main beam to main beam and cross tee to cross tee connection shallhave a pull out strength of more than 100kg. The T Sections shall be made of hot dippedgalvanized steel of 90 gsm as per IS 277 (2003) and pre-painted steel with baked polyesterpaint with 0T bending capability. All border cross tee/main beam shall be levelled usingperimeter fill. |
| 65 | Providing and fixing 90 cm x 60 cm Granite plate engraving 10 cm. Height letter,figures including painting the lefters/figures with approved colour and shade complete |
| 66 | ProvidingandfixingheavydutyinterlockingconcreteRubbermouldglossypavingblocksof80mm thickness of having a strength of 400 Kilogram/Sq.cm. of approved quality and shape on a bedof crushed sand of 25 to 30 mm thick including skirting jointsandcleaning etc. complete. (using 100% crushed sand)(SSR-2021-22/Item No.-33.54/Page No.-) |
| 67 | Full Height Steel Storage @ 750Lx450Dx2100HTProviding and fixing Openable Steel Storage of 750 x 450 x 2100Ht, with 4 adjustableshelves, Complete body & shutter made in 0.8 mm thick & Top in 2 mm thick CRCA, 4Shutter to be mounted with the help of cup hinges, and 4 adjustable levelers, enitre storagein powder coated finish with 60 to 80 microns as as per drawing. |
| 68 | Executive\"sTable @ 1800Lx900Dx750HTProviding&Fixing ofTable @1800Lx900Dx750HT-TOP&GABLEENDto bemade of Membrane finish with soft water fall edges & curved panel & Decorated Anodizedsection MODESTYPANEL to be made of 18 mm thick Prelaminated particle board with PVC edge band as per drawing |
| 69 | 12 Seater Reading Table for Library @ 3600Lx1200Dx750HTProviding andFixing 12 Seater Reading Table forLiberary @3600Lx1200Dx750HTTop:made from 25 mm Prelaminated Particle board.All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine.Gable Ends : made from 25 mm Prelaminated Particle board.All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine. Modesty panel : Made from 18mm both side prelaminated particle boards.All edges are covered by 0.8mm PVCedge bands glued by hot melt glueapplied by auto edge banding machine. |
| 70 | Free Standing Table @ 1200Lx600Dx750HTProviding and fixing Table of Size 1200 x 600 x 750 mm. Top: made from 25 mm Prelaminated Particle board.All edges are covered by 2 mm. Thk. PVC edge bands glued by hot melt glue applied by auto edge banding machine.Legs : C Shape made from CRCA Sheet with Powder Coat finish. Modesty panel : Made from 18mm both side prelaminated particle boards.All edges are covered by 0.8mm PVC edge bands glued by hot melt glue applied by auto edge banding machine.KEYBOARD TRAY ( WITHOUT MOUSE TRAY ) :-Metal Powder Coated - Black Color, CPU TROLLEY :-Metal Powder Coated - Black Color, 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board, |
| 71 | Book Case with Glass Shutter @ 825Lx300Dx1650HTProviding & Fixing of Book Case with Glass Shutter @ 825Lx300Dx1650HT:- To be made out of complete body & in 0.7mm thick CRCA & Shutter in 1.2mm thick CRCA with glass pannel in Powder coating finish as per drawing. |
| 72 | Providing&ArrangemntofMidBack,ECOCTSMechanism,FixedArmrest,GasliftforSeatheight adjustment, Standard 5-prong P/Nylon Base with Fabric Upholstery |
| 73 | Providing & Arrangemnt of High Back Chair - TILT MECHANISM WITH MULTILOCKING, HIGH DENSITY CUSHION ON SEAT COMPOSITE LEATHER WITH METALLIC SILVER FINISH BASE AND ARMS WITH P.U.CASTORS GASLIFT FOR HEIGHT ADJUSTMENT. |
| 74 | Transportation charges of drilling machine, pipes and all accesorries of tube well etc.complete. |
| 75 | Drilling of bore well 150 mm dia. including drilling in all strata, removing drilled stuff out side the bore well complete. |
| 76 | Providing with thread Plain Iron casing pipes of 150 mm dia and 4.80mm thick Pipes of M.S.E.R.W. medium class (I.S.1239)for 150 mm dia. Tube-well, including loweringinto bore well without any damage & welding etc. complete. |
| 77 | Providing Perforated Iron casing pipes of 150 mm dia and of 4.80mm thickness of M.S.E.R.W. medium class (I.S.1239), including loweringinto tube well without any damage etc. complete. |
| 78 | Providing and fixing steel cap (I.S. 1239) for threaded Iron casing pipes including all acessesories complete. |
| 79 | Providiing gravel packing around the tube well & as directed by the engineer-Incharge etc. complete. |
| 80 | Improving (Development) process of tube well etc. complete. |
| 81 | Providing and fixing bell plug including all acessesories etc. complete. |
| 82 | Providing Wooden blocks of Mango trees of size 1.00m in length x 0.15m. width x 0.20m. thick. etc. complete. |
| 83 | Providing and fixing steel clamps 1.00m in length x 0.10m. width x 0.01m. thick. etc. Complete. |
| 84 | Providing Flushing (Air Lift method) after completion of Tubwell and capacity test by 90 degree \"V\" notch for half an hour as per G.S.D.A. Norms etc. Complete. |
